A Dual-Polarized, Dual-Frequency, Corrugated Feed Horn for SMAP
No abstract available
climate predications↗
SEARCH · Search NASA
Results for “Corrugated Horns”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A Dual-Polarized, Dual-Frequency, Corrugated Feed Horn for SMAP
SMAP will be the first Earth science mission to use a deployable 6m mesh reflector for both radar and radiometric measurements from low Earth orbit. The instrument antenna will spin at about 14 rpm, making the design of both reflector and feed more challenging. While the performance requirements imposed by the radar instrument are relatively benign, those pertinent to the radiometer are more difficult to meet. Extreme care was necessary in designing the feed, especially from a performance stability perspective. Thermal variations due to the spacecraft going in and out of eclipse during orbit and direct solar radiation into the horn are just two of the challenges faced during the design phase. In this paper, the basic concepts behind the design of SMAP's feed will be discussed. Each component of the feed will be analyzed in detail with particular emphasis on its impact on major RF requirements. Overall performance of the feed will also be discussed.
deployable reflector↗
A parametric study of cut-off corrugated surface properties
Corrugated horns involve a junction between the corrugated surface and a conducting groundplane. Proper horn design requires an understanding of the electromagnetic properties of the corrugated surface and this junction. Therefore, an integral equation solution has been used to study the influence of corrugation density and shape on the power loss. Surface current, and the scattering from a groundplane-corrugated surface junction. Both square and vee shape corrugations have been considered over the range of corrugation depths where the surface acts as a cut-off corrugated surface.
Mentzer, C. A.↗
Computing Scattering Matrices For Circular Waveguides
Scattering Matrix Program for Circular Waveguide Junctions computes scattering matrix for series of circular waveguide sections. Sections must have same axis, but radius and length of each section completely arbitrary. Devices analyzed include simple waveguide step discontinuity like that used in a dual-mode horn, stepped matching section, or corrugated waveguide section with constant or varying slot depth. Certain types of corrugated horns also analyzed with program. Mathematical model used in program accurately predicts reflection and transmission characteristics of such devices, taking into account excitation of modes of higher order as well as multiple reflections and energy stored at each discontinuity. Written in FORTRAN 77.
Hoppe, Daniel J.↗
Optics Design for the U.S. SKA Technology Development Project Design Verification Antenna
The U.S. design concept for the Square Kilometer Array (SKA) program is based on utilizing a large number of 15 meter dish antennas. The Technology Development Project (TDP) is planning to design and build the first of these antennas to provide a demonstration of the technology and a solid base on which to estimate costs. This paper describes the performance of the selected optics design. It is a dual-shaped offset Gregorian design with a feed indexer that can accommodate corrugated horns, wide band single pixel feeds or phased array feeds.
Corrugated Horns↗
Measurements of very low-sidelobe conical horn antennas
A description is given of conical corrugated-horn antennas that were designed for millimeter-wave radiometers with a 7 degree field of view, namely the Differential Microwave Radiometers (DMRs) that will measure the large-angular-scale anisotropy of the cosmic background radiation that is generally thought to be the remnant of the primeval explosion, the Big Bang. The DMRs will be part of the Cosmic Background Explorer (COBE) satellite. Measured test results for three radiometers at 31.4, 53, and 90 GHz are reported along with those of a circular polarization orthomode transducer designed and characterized at 31.4 GHz. The measurement techniques and facilities are described, including an outdoor far-field facility where measurements down to levels 90 dB below the main beam maximum were achieved. The goal of achieving very low-sidelobe antennas with good symmetry has been demonstrated.
Toral, Marco A.↗
Pattern measurements of a low-sidelobe horn antenna
The techniques and results of power pattern measurements of a corrugated horn antenna designed for low sidelobes are reported. The power pattern was measured to levels 90 dB below the main beam maximum in both the E- and H-planes. The measured patterns were found to be in good agreement with predictions from existing theory for the performance of corrugated scalar feeds.
Janssen, M. A.↗
Pattern measurements of a low-sidelobe horn antenna
The techniques and results of measuring the power pattern of a corrugated horn antenna designed for low sidelobes to levels 90 dB below the main beam maximum on both the E- and H- planes are presented. The study was motivated by a requirement for an antenna with very low side lobes to measure properties of the cosmic microwave background radiation from a satellite. The particular application calls for horn antennas of approximately 7 deg beamwidth, operating at discrete frequencies in the range of 20-90 GHz. It is demonstrated that the side lobes of horn antennas can be measured to significantly lower levels than has been achieved previously. Finally, it is noted that an improvement could be achieved by allowing for longer signal integrations and incorporating a switched reference measurement scheme to enable the accurate determination of very low signal levels.
Janssen, M. A.↗
Optimizing the G/T ratio of the DSS-13 34-meter beam-waveguide antenna
Calculations using Physical Optics computer software were done to optimize the gain-to-noise-temperature (G/T) ratio of Deep Space Station (DSS)-13, the Deep Space Network's (DSN's) 34-m beam-waveguide antenna, at X-band for operation with the ultra-low-noise amplifier maser system. A better G/T value was obtained by using a 24.2-dB far-field-gain smooth-wall dual-mode horn than by using the standard X-band 22.5-dB-gain corrugated horn.
Esquivel, M. S.↗
A 20-dB quasi-integrated horn antenna
A multimode quasi-integrated dipole-fed horn antenna is presented with a performance comparable to that of waveguide-fed corrugated horn antennas. The antenna has been designed using fullwave analysis and has been fabricated and tested at 91 GHz. The horn has a gain of 20 dB with very symmetric patterns, a Gaussian coupling efficiency of 97 percent, and a cross-polarization level of -22.7 dB. The antenna provides a significant improvement in integrated antenna designs and is suitable for millimeter-wave communication and radar systems and as a Gaussian-beam launcher in quasi-optical receiver systems.
Eleftheriades, George V.↗
Integrated horn antennas for millimeter-wave applications
The development of integrated horn antennas since their introduction in 1987 is reviewed. The integrated horn is fabricated by suspending a dipole antenna, on a thin dielectric membrane, in a pyramidal cavity etched in silicon. Recent progress has resulted in optimized low- and high-gain designs, with single and double polarization for remote-sensing and communication applications. A full-wave analysis technique has resulted in an integrated antenna with performance comparable to that of waveguide-fed corrugated-horn antennas. The integrated horn design can be extended to large arrays, for imaging and phased-array applications, while leaving plenty of room for the RF and IF processing circuitry. Theoretical and experimental results at microwave frequencies and at 90 GHz, 240 GHz, and 802 GHz are presented.
Rebeiz, Gabriel M.↗
A multiple-beam spherical reflector antenna
A spherical reflector with multiple feeds is considered for application in communications satellite systems. Data are presented which show that spherical reflectors possessing relatively high gain (40 db) and very small phase path error are feasible. A design of a spherical reflector utilizing corrugated horn feeds is considered. Radiation patterns are computed using the physical-optics technique. The designed antenna is approximately 60 lambda in diameter. Calculations performed for this antenna with three beams indicate that each beam has a gain of about 42 db, a beamwidth of 1.4 deg, and sidelobes that can be expected to be at least 28 db down. These results indicate that the feature of low sidelobes makes the spherical reflector a consideration for a multiple-beam communications satellite antenna.
Woo, R.↗
Optimization of the design parameters for a wide-band radiometric system
The optimun design parameters for a swept frequency wide-band radiometric antenna system for spacecraft applications are studied. Wide band antenna systems are needed to observe layered surfaces which are frequency sensitive and require multiple measurements for interpretation. The lowest frequency band of interest is between 1.4 to 2.8 Ghz. Starting with a given size reflector fed in the offset mode by a corrugated horn located at the focus of the parabola, the primary performance indexes; e.g., half power beamwidth, cross polarization level, and overall beam efficiency were calculated over a wide frequency range (two to one) for different physical horn dimensions and for different values of f/D ratio. These data are used to find the best design under given restriction of reflector size and blockage.
Agrawal, P. K.↗
Feasibility of inertialess conscan utilizing modified DSN feedsystems
The closed-loop conical-scan (conscan) technique has proven to be a useful method for pointing the DSN antennas more accurately than is possible by open-loop methods. As presently implemented, the antenna beam is scanned about the received signal direction by physical movement of the antenna. While straightforward, this approach has at least two disadvantages. Firstly, because of structural distortions, finite angle encoder resolution, and drive servo response, the actual antenna beam direction only approximates the commanded beam direction. Secondly, because of the large mass moved during scan, the rate of scan is severely restricted. If there are significant gain or signal level variations during a scan period, the conscan system interprets these variations as antenna pointing error. Both of these disadvantages would be alleviated in an inertialess conscan system in which the beam scanning was performed electronically. Recently, standard JPL antenna feedhorn software was upgraded to calculate, among other things, asymmetric corrugated horn radiation patterns of the type that would be needed for electronic beam scan. The required horn excitation is discussed and the results were described.
Potter, P. D.↗
Microwave blackbodies for spaceborne receivers
The properties of microwave blackbody targets are explained as they apply to the calibration of spaceborne receivers. Also described are several practicable, blackbody targets used to test and calibrate receivers in the laboratory and in the thermal vacuum chamber. Problems with the precision and the accuracy of blackbody targets, and blackbody target design concepts that overcome some of the accuracy limitations present in existing target designs, are presented. The principle of the Brewster angle blackbody target is described where the blackbody is applied as a fixed-temperature test target in the laboratory and as a variable-temperature target in the thermal vacuum chamber. The reflectivity of a Brewster angle target is measured in the laboratory. From this measurement, the emissivity of the target is calculated. Radiatively cooled thermal suspensions are discussed as the coolants of blackbody targets and waveguide terminations that function as calibration devices in spaceborne receivers. Examples are given for the design of radiatively cooled thermal suspensions. Corrugated-horn antennas used to observe the cosmic background and to provide a cold-calibration source for spaceborne receivers are described.
Stacey, J. M.↗
An upward looking airborne millimeter wave radiometer for atmospheric water vapor sounding and rain detection
A 90/180 GHz multichannel radiometer is currently under development for NASA's 1985 Hurricane Mission onboard the Convair 990 research aircraft. The radiometer will be a fixed beam instrument with dual corrugated horns and a common lens antenna designed to operate simultaneously at 90 and 180 GHz. The all solid state front-end will contain three double side band data channels at 90 + or - 3 GHz, 180 + or - 3 GHz, and 180 + or - 7 GHz. The airborne radiometer will mount in a window port on the CV-990 and will maintain a fixed beam view approximately 14 degrees off zenith. The radiometer design is a Dicke chopper arrangement selected to achieve maximum absolute temperature accuracy and minimum brightness temperature sensitivity. Analog outputs of the three data channels will be calibrated dc voltages representing the observed radiometric brightness temperatures over the selected integration time.
Gagliano, J. A.↗
Calculating Scattering At Circular-Waveguide Junctions
Computer program calculates scattering matrices for circular waveguides including step discontinuities between collinear sections of different radii. Radius and length of each section specified arbitrarily. Examples of devices analyzed with program include waveguides with single step discontinuities, matching sections, corrugated straight sections, and corrugated horns. Sections with smooth tapers and horns with arbitrary profiles approximated by series of small steps.
Hoppe, D. J.↗
Measured performance of the half-scale accurate antenna reflector
A corrugated horn was designed and fabricated for use as a feed for the half-scale accurate antenna reflector. This feed allows the reflector to be used in a compact range configuration as part of a microwave reflectance measuring system. The horn design is described, and the measured farfield patterns of the horn are presented. The horn was installed at the focus of the reflector, and the nearfield of the antenna was measured. The results of these measurements are presented and discussed with respect to the compact range application.
Lambert, Kevin M.↗