Search NASA⌕ Search

SEARCH · Search NASA

Results for “DEMs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Continuum Correlations from CFD-DEM Modeling of Conduction Heat Transfer in Granular Flows

Heat transfer between a surface and flowing particles is analyzed to improve the accuracy of continuum models for wall-to-bed heat transfer in a fluidized bed. Discrete element modeling (DEM) is used to model a fluidized bed heat exchanger where heat enters the system through a heated wall. The DEM heat transfer predictions are validated against published experimental work (Brewster et al., 2024) with less than 15% error. In previous work by Morris et al. (2015), a continuum model was developed using data from high-fidelity DEM simulations of chute flows. In the current study, the continuum model is extended and validated for fluidized beds. The sensitivity of the continuum heat transfer model parameters, which was not quantified in previous studies, is also investigated. It is observed that for a given particle with specific properties, e.g. the particle size, roughness, and conduction lens radius, the continuum correlation developed for heat transfer from a heated boundary to the particle bed depends mainly on the solid fraction or porosity of the particle bed for a given fluid. The new continuum heat transfer model is then validated over a wide range of superficial velocities via comparisons to both discrete element and experimental data. It is shown that this correlation is valid for a large range of particle flow conditions from chute flows to fluidized beds with less than 10% error as compared to DEM predictions.

14 SOLAR ENERGY↗

Fabric evolution and dilatancy within anisotropic critical state theory guided and validated by DEM

Fabric, expressed by means of an evolving deviatoric fabric tensor F, plays a very important role in the anisotropic mechanical response of granular materials. The Anisotropic Critical State Theory (ACST) addresses fabric anisotropy by rendering dilatancy a function of F, in addition to other state variables. In this paper, 3D DEM is used to guide the specific grain-level definition of F, the formulation of its continuum evolution equation and its effect on anisotropic dilatancy within ACST. DEM provides stress-ratio and shear strain variations as input for ACST analytical calculations of evolving fabric tensor and dilatancy, which are then favourably compared with totally independent direct measurements of these quantities by DEM. Furthermore, dilatancy is shown to be strongly affected by the contact normal-based fabric tensor Fc, whose evolution is best described by a continuum equation within ACST that includes dilatancy and a quantity related to particle orientation-based fabric tensor Fp. The aforementioned favourable comparison of the results for fabric tensor and dilatancy obtained independently by ACST and DEM, confirms the validity of the core framework of ACST irrespective of any constitutive model that addresses the deviatoric stress-strain relations.

58 GEOSCIENCES↗

Radar and Lidar Radar DEM

Using radar and lidar data, the aim is to improve 3D rendering of terrain, including digital elevation models (DEM) and estimates of vegetation height and biomass in a variety of forest types and terrains. The 3D mapping of vegetation structure and the analysis are useful to determine the role of forest in climate change (carbon cycle), in providing habitat and as a provider of socio-economic services. This in turn will lead to potential for development of more effective land-use management. The first part of the project was to characterize the Shuttle Radar Topography Mission DEM error with respect to ICESat/GLAS point estimates of elevation. We investigated potential trends with latitude, canopy height, signal to noise ratio (SNR), number of LiDAR waveform peaks, and maximum peak width. Scatter plots were produced for each variable and were fitted with 1st and 2nd degree polynomials. Higher order trends were visually inspected through filtering with a mean and median filter. We also assessed trends in the DEM error variance. Finally, a map showing how DEM error was geographically distributed globally was created.

remote sensing↗

Reverse scaling of a bonded-sphere DEM model: Formulation and application to lignocellulosic biomass microstructures

We explore scaling laws for adapting a bonded-sphere discrete element method (BS-DEM) model developed for woody structural mechanics at the millimeter scale to model the mechanics of realistic lignocellulosic biomass microstructures. Two scaling approaches, i.e., the reverse coarse graining (RCG) and equivalent bulk behavior (EBB), are proposed based on the classical mechanics principles and assessed in the single-particle compression and rectangular cuboid block tension tests. The EBB approach is recommended for BS-DEM models with general 3D geometries and is applied to simulate the microindentation test on a realistic microscale pinewood specimen. Simulations are performed to elucidate the impact of specimen thickness and loading position on the specimen’s force–deformation behavior. Furthermore, the range of Young’s modulus obtained from the calibrated BS-DEM simulations can match the experimental measurements. This is the first-of-its-kind study that has explored scale-bridging modeling approaches in biomass micromechanics and has proposed solutions based on BS-DEM models in the microscale.

59 BASIC BIOLOGICAL SCIENCES↗

CFD-DEM Onset of Motion Analysis for Application to Bed Scour Risk Assessment

This CFD study with DEM was done as a part of the Federal Highway Administration’s (FHWA’s) effort to improve scour design procedures. The Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) model, available in CD-Adapco’s StarCCM+ software, was used to simulate multiphase systems, mainly those which combine fluids and solids. In this method the motion of discrete solids is accounted for by DEM, which applies Newton's laws of motion to every particle. The flow of the fluid is determined by the local averaged Navier–Stokes equations that can be solved using the traditional CFD approach. The interactions between the fluid phase and solids phase are modeled by use of Newton's third law. The inter-particle contact forces are included in the equations of motion. Soft-particle formulation is used, which allows particles to overlap. In this study DEM was used to model separate sediment grains and spherical particles laying on the bed with the aim to analyze their movement due to flow conditions. Critical shear stress causing the incipient movement of the sediment was established and compared to the available experimental data. An example of scour around a cylindrical pier is considered. Various depths of the scoured bed and flow conditions were taken into account to gain a better understanding of the erosion forces existing around bridge foundations. The decay of these forces with increasing scour depth was quantified with a ‘decay function’, which shows that particles become increasingly less likely to be set in motion by flow forces as a scour hole increases in depth. Computational and experimental examples of the scoured bed around a cylindrical pier are presented.

97 MATHEMATICS AND COMPUTING↗

BOREAS HYP-8 DEM Data Over The NSA-MSA and SSA-MSA in The AEAC Projection

These data were derived from the original Digital Elevation Models (DEMs) produced by the Boreal Ecosystem-Atmosphere Study (BOREAS) Hydrology (HYD)-8 team. The original DEMs were in the Universal Transverse Mercator (UTM) projection, while this product is projected in the Albers Equal-Area Conic (AEAC) projection. The pixel size of the data is 100 meters, which is appropriate for the 1:50,000-scale contours from which the DEMs were made. The original data were compiled from information available in the 1970s and 1980s. This data set covers the two Modeling Sub-Areas (MSAs) that are contained within the Southern Study Area (SSA) and the Northern Study Area (NSA). The data are stored in binary, image format files. The DEM data over the NSA-MSA and SSA-MSA in the AEAC projection are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

Knapp, David E.↗

A simplified DEM-CFD approach for pebble bed reactor simulations

In pebble bed reactors (PBR's), the pebble flow and the coolant flow are coupled with each other through coolant-pebble interactions. Approaches with different fidelities have been proposed to simulate similar phenomena. Coupled Discrete Element Method-Computational Fluid Dynamics (DEM-CFD) approaches are widely studied and applied in these problems due to its good balance between efficiency and accuracy. In this work, based on the symmetry of the PBR geometry, a simplified 3D-DEM/2D-CFD approach is proposed to speed up the DEM-CFD simulation without significant loss of accuracy. Pebble flow is simulated by a full 3-D DEM, while the coolant flow field is calculated with a 2-D CFD simulation by averaging variables along the annular direction in the cylindrical geometry. Results show that this simplification can greatly enhance the efficiency for cylindrical core, which enables further inclusion of other physics such as thermal and neutronic effect in the multi-physics simulations for PBR's. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Discrete-Element and Material-Point Method (DEM and MPM) Based Solvers for Sustainable Technologies

We present the use of discrete element method (DEM) and material point method (MPM) in three relevant green technology applications that include biomass feedstock handling, lithium-ion battery manufacturing, and high-pressure reverse osmosis. Our open-source DEM and MPM solvers are developed using performance portable grid and particle management library, AMReX, thus enabling superior performance on NVIDIA and AMD GPUs with > 100 million particles. Our DEM solver resolves the motion of individual particles in a granular system and includes a bonded sphere method for modeling non-spherical particles along with Hertzian and liquid bridge-based contact models. We simulate highly variable biomass feedstock flows in large-scale hoppers for biofuel production and electrode calendering in battery manufacturing using DEM. Our simulations predict flow blockage in large scale biomass hoppers and electrode microstructure variations, thus providing valuable information for biofuel and battery manufacturers, respectively. The second half of the talk will be on MPM and its application towards pore resolved simulations of reverse osmosis membranes under compressive loads. We present a validation study of our MPM simulations with membrane microscopy imaging thus providing useful insights on membrane stability under high pressure conditions. We also present a spectral stability analysis of using linear hat, quadratic and cubic spline basis in MPM indicating regions of numerical stability.

BIOMASS FUELS,MATHEMATICS AND COMPUTING↗

Utah FORGE: Area LiDAR Bare Earth DEM Mosaic

This is a mosaic of 154 bare earth DEM panels (0.5 m resolution) acquired during Phase II of the Utah FORGE project. The DEM covers the western Mineral Mountains and adjoining basin including the Roosevelt Hot Springs area. The coordinates are in UTM Zone 12, NAD 83 and elevation units are in meters. The DEM is in GeoTiff format.

15 GEOTHERMAL ENERGY↗

DEM, DSM, and Cleaned LiDAR Point Cloud Data from the NGEE Arctic UAS Campaigns at the Teller 27 Field Site from 2017 and 2018, Seward Peninsula, Alaska

A Digital Elevation Model (DEM) and Digital Surface Model (DSM) were derived from airborne Light Detection and Ranging (LiDAR) data collected from Los Alamos National Laboratory's (LANL) heavy-lift unoccupied aerial system (UAS) quadcopter and hexacopter platforms operated by Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) scientists from the EES-14 group at LANL. These data were collected in August 2017 and July 2018 at the NGEE Arctic field site near mile marker 27 of the Bob Blodgett Nome-Teller Memorial Highway between Nome, Alaska and Teller, Alaska. A Vulcan Raven X8 Airframe (Mitcheldean, Gloucestershire, UK), DJI Matrice 600 Pro Airframe (Shenzhen, China), and Routescene UAV LiDARSystem (Edinburgh, Scotland, UK) were used to collect LiDAR data. Following pre-processing in Routescene LidarViewer Pro software, the LiDAR point clouds were cleaned and processed using CloudCompare software to separate ground and off-ground points. A high resolution DEM and DSM were then created using ArcGIS Pro software. This data package contains fully cleaned point clouds of ground and off-ground points (.las), a 25 cm DEM (.tif), and a 25 cm DSM (.tif) for the Teller 27 field site. Ancillary aircraft data, flight mission parameters, weather conditions, and raw lidar data and imagery can be found in the L0 datasets for these campaigns: NGA299 (2017) and NGA297 (2018). Minimally processed point clouds and auxiliary files can be found in the L1 dataset: NGA304 (2017 and 2018).The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a 15-year research effort (2012-2027) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗

A three-dimensional meso-scale approach to concrete fracture based on combined DEM with X-ray μCT images

Highlights: • We investigate fracture in concrete beams subjected to 3-point bending. • We use a discrete element method (DEM) to capture fracture. • Concrete is described as 4-phase material. • Evolution of micro-structural phenomena is investigated. • The 3D results are carefully compared with the 2D ones. - Abstract: The paper shows three-dimensional (3D) numerical mesoscopic results on progressive concrete fracture at aggregate level in a notched concrete beam under bending. A classical particle discrete element method was used to capture fracture in concrete. Heterogeneity was taken into account with a 4-phase concrete description: aggregate, cement matrix, macro-voids and interfacial transitional zones. Both the real shape and location of aggregate particles in concrete were assumed in DEM analyses based on X-ray μCT scans. A satisfactory agreement in terms of the vertical force versus crack mouth opening displacement evolution and crack geometry was achieved between DEM analyses and own laboratory tests. The evolution of broken contacts, contact normal forces, particle rotations, internal energies was studied at the aggregate level. The 3D results were also carefully compared with the 2D ones. The 3D model proved to be a promising simulation tool in predicting concrete fracture at the mesoscopic and macroscopic level.

36 MATERIALS SCIENCE↗

Extraction of Hydrological Proximity Measures from DEMs using Parallel Processing

Land surface topography is one of the most important terrain properties which impact hydrological, geomorphological, and ecological processes active on a landscape. In our previous efforts to develop a soil depth model based upon topographic and land cover variables, we extracted a set of hydrological proximity measures (HPMs) from a Digital Elevation Model (DEM) as potential explanatory variables for soil depth. These HPMs may also have other, more general modeling applicability in hydrology, geomorphology and ecology, and so are described here from a general perspective. The HPMs we derived are variations of the distance up to ridge points (cells with no incoming flow) and variations of the distance down to stream points (cells with a contributing area greater than a threshold), following the flow path. These HPMs were computed using the D-infinity flow model that apportions flow between adjacent neighbors based on the direction of steepest downward slope on the eight triangular facets constructed in a 3 x 3 grid cell window using the center cell and each pair of adjacent neighboring grid cells in turn. The D-infinity model typically results in multiple flow paths between 2 points on the topography, with the result that distances may be computed as the minimum, maximum or average of the individual flow paths. In addition, each of the HPMs, are calculated vertically, horizontally, and along the land surface. Previously, these HPMs were calculated using recursive serial algorithms which suffered from stack overflow problems when used to process large datasets, limiting the size of DEMs that could be analyzed using that method to approximately 7000 x 7000 cells. To overcome this limitation, we developed a message passing interface (MPI) parallel approach for calculating these HPMs. The parallel algorithms of the HPMs spatially partition the input grid into stripes which are each assigned to separate processes for computation. Each of those processes then uses a queue data structure to order the processing of cells so that each cell is visited only once and the cross-process communications that are a standard part of MPI are handled in an efficient manner. This parallel approach allows analysis of much larger DEMs as compared to the serial recursive algorithms. In this paper, we present the definitions of the HPMs, the serial and parallel algorithms used in their extraction and their potential applications in hydrology, geomorphology and ecology.

54 ENVIRONMENTAL SCIENCES↗

Effects of curvature-related DEM contact model on the macro- and micro-mechanical behaviours of granular soils

The presented paper conducted a comprehensive comparison between the Hertz-Mindlin model and the linear spring model in true triaxial shear simulations of granular soils using the discrete element method (DEM). The no-slip Hertz-Mindlin model for general elastic non-spherical particles with smooth surfaces was revisited, and implemented for superellipsoidal particles in an in-house DEM code. Three groups of specimens with a grain size distribution of Ottawa 20-30 sands, consisting of spheres, ellipsoids, and superellipsoids, respectively, were subjected to triaxial shear DEM simulations with the Hertz-Mindlin model and the linear spring model. The corresponding mechanical behaviours were examined in terms of a series of macro-and micro-parameters. It is found that the linear spring model is able to resemble the Hertz-Mindlin model on aspects of both microscopic and macroscopic mechanical behaviours of granular media with spherical and/or non-spherical particles. This finding suggests that the linear spring model can be used to investigate micro-mechanical behaviours of granular soils even with complex particle shapes.

42 ENGINEERING↗

BOREAS HYD-8 DEM Data Over the NSA-MSA and SSA-MSA in the UTM Projection

The BOREAS HYD-8 team focused on describing the scaling behavior of water and carbon flux processes at local and regional scales. These DEMs were produced from digitized contours at a cell resolution of 100 meters. Vector contours of the area were used as input to a software package that interpolates between contours to create a DEM representing the terrain surface. The vector contours had a contour interval of 25 feet. The data cover the BOREAS MSAs of the SSA and NSA and are given in a UTM map projection. Most of the elevation data from which the DEM was produced were collected in the 1970s or 1980s. The data are stored in binary, image format files. The data files are available on a CD-ROM (see document number 20010000884) or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Wang, Xue-Wen↗

A Review of Discrete Element Method (DEM) Particle Shapes and Size Distributions for Lunar Soil

As part of ongoing efforts to develop models of lunar soil mechanics, this report reviews two topics that are important to discrete element method (DEM) modeling the behavior of soils (such as lunar soils): (1) methods of modeling particle shapes and (2) analytical representations of particle size distribution. The choice of particle shape complexity is driven primarily by opposing tradeoffs with total number of particles, computer memory, and total simulation computer processing time. The choice is also dependent on available DEM software capabilities. For example, PFC2D/PFC3D and EDEM support clustering of spheres; MIMES incorporates superquadric particle shapes; and BLOKS3D provides polyhedra shapes. Most commercial and custom DEM software supports some type of complex particle shape beyond the standard sphere. Convex polyhedra, clusters of spheres and single parametric particle shapes such as the ellipsoid, polyellipsoid, and superquadric, are all motivated by the desire to introduce asymmetry into the particle shape, as well as edges and corners, in order to better simulate actual granular particle shapes and behavior. An empirical particle size distribution (PSD) formula is shown to fit desert sand data from Bagnold. Particle size data of JSC-1a obtained from a fine particle analyzer at the NASA Kennedy Space Center is also fitted to a similar empirical PSD function.

Lane, John E.↗

Aster Global Dem (gdem) Version 3

The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) is a 14-channel imaging instrument operating on NASA’s Terra satellite since 1999. ASTER’s visible–near infrared (VNIR) instrument, with three bands and a 15 m Instantaneous field of view (IFOV), is accompanied by an additional VNIR band using a second, backward-looking telescope. Collecting along-track stereo pairs, the geometry produces a base-to-height ratio of 0.6. In 2009, the ASTER Science Team released Version 1 of the global DEM (GDEM) based on stereo correlation of 1.2 million ASTER scenes. The DEM has 1 arc-second latitude and longitude postings (~30 m) and employed cloud masking to avoid cloud-contaminated pixels. The GDEM covers all of the Earth’s land surface from 83 degrees north to 83 degrees south latitude. Version 2 was released in 2011, with notable improvements in coverage and accuracy. In 2019, the final, Version 3, was released; again improving on coverage and removing almost all artifacts. Th GDEM is a unique, global high spatial resolution digital elevation dataset available to all users at no cost. In addition, a second unique dataset was produced and released. The raster-based ASTER Global Water Body Dataset (ASTWBD) identifies the presence of permanent water bodies, and marks them as ocean, lake, or river. An accompanying DEM file indicates the elevation for each water pixel. To date, over 110+ million 1x1 degree GDEM tiles have been distributed.

Crippen, R.↗

An Orthogonal Recursive Bisection (ORB) Based Time Advancement Algorithm for CFD-DEM Solvers

The time integration of the granular phase in coupled computational fluid dynamics (CFD) – discrete element method (DEM) simulations presents a unique computational challenge brought about by the large variations in particle collisional time scales. Particles in the dilute regions of the computational domain can be advanced with large time steps while dense regions require much smaller time increments. However, the time step size in most solvers is globally set as the limit for accuracy and stability imposed by the collisions and is typically orders of magnitude less than that required away from collisions. This work addresses this precise issue and provides a strategy to avoid the use of a global conservative small time step size for the entire set of particles.A novel time stepping algorithm for CFD-DEM solvers using a partitioning approach using orthogonal recursive bisection (ORB) that allows for variable time steps among particles is described and its computational performance is compared against baseline explicit methods, typically used in several CFD-DEM solvers. ORB has advantages of being relatively quick and easy to update incrementally and has the required heuristic behavior (i.e., it will split the region in half with a cluster on each side) when groups of particles are well separated (clustered). The algorithm presented in this work uses a local time stepping approach to resolve collisional time scales for subsets of particles that are present at the leaves of the ORB, thereby resulting in substantial reduction of computational cost. The parallel implementation of this method where a ``knapsack” algorithm is used in tandem with ORB for effective load-balancing is also presented, where a best possible partitioning is obtained based on number of particles and local time-stepping costs. The algorithm is tested against benchmark problems with varying particle distributions that include fluidized bed and riser flow scenarios. Preliminary results indicate that the approach is 2-3X faster than traditional explicit methods for problems that involve both dense and dilute regions, while maintaining the same level of accuracy.

adaptive timestepping↗

DEM and MELT: A Modular and Compact In-Can Melting Technology Dedicated to D and D and Remediation Waste - 20033

The DEM and MELT In-Can vitrification process is designed to process intermediate and high level waste coming for D and D and remediation operations. It is developed to treat liquid and solid waste, to produce a small amount of secondary waste and to minimize investment and operating costs. This In-Can vitrification process is also developed with a compact and modular design and can be adapted regarding nuclear operators' needs and requirements. Furthermore, this robust and simple process is flexible enough to accommodate most uncertainties on waste composition. The DEM and MELT process is developed through the French consortium coordinated by CEA which gathers Orano, ECM technologies and Andra. In the frame of this project, Orano has designed a compact and modular layout of the process allowing an efficient in situ implementation, close to the waste to be treated. This paper presents the compact and modular design of the DEM and MELT process and the way it can be used for a short duration, as a decommissioning tool aimed to be dismantled just after the treatment operation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗