Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIAMOND GROWTH MECHANISM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Computational modelling of Er(3+): Garnet laser materials

The Er(3+) ion has attracted a lot of interest for four reasons: (1) Its (4)I(sub 13/2) yields (4)I(sub 15/2) transition lases in the eyesafe region near 1.5 micron; (2) the (4)I(sub 13/2) transition lases near 2.8 micron, an important wavelength for surgical purposes; (3) it displays surprisingly efficient upconversion with lasing observed at 1.7, 1.2, 0.85, 0.56, 0.55, and 0.47 micron following 1.5 micron pumping; and (4) it has absorption bands at 0.96 and 0.81 micron and thus can be diode pumped. However, properties desirable for upconversion reduce the efficiency of 1.5 and 3 micron laser operation and vice versa. Since all of the processes are influenced by the host via the crystal field induced stark splittings in the Er levels, this project undertook modelling of the host influence on the Er lasinng behavior. While growth and measurement of all ten Er(3+) doped garnets is the surest way of identifying hosts which maximize upconversion (or conversly, 1.5 and 3 micron performance), it is also expensive - costing approximately $10,000/material or approximately $100,000 for the materials computationally investigated here. The calculations were performed using a quantum mechanical point charge model developed by Clyde Morrison at Harry Diamond Laboratories. The programs were used to fit the Er:YAG experimental energy levels so that the crystal field parameters, B(sub nm) could be extracted. From these radial factors, rho (sub n) were determined for Er(3+) in garnets. These, in combination with crystal field components, Anm, available from X-ray data, were used to predict energy levels for Er in the other nine garnet hosts. The levels in Er:YAG were fit with an rms error of 12.2/cm over a 22,000/cm range. Predicted levels for two other garnets for which literature values were available had rms errors of less than 17/cm , showing the calculations to be reliable. Based on resonances between pairs of calculated stark levels, the model predicts GSGG as the best host for 1.5 micron laser operation, GSGG or YSAG as the best host for a 2.8 micron operation, and LuGG as the best host for an upconversion material.

Spangler, Lee H.↗
NASA NTRS2017

Diamond-Like Carbon Nanorods and Fabrication Thereof

Novel sp. (sup 3) rich diamond-like carbon (DLC) nanorod films were fabricated by hot filament chemical vapor deposition technique. The results are indicative of a bottom-up self-assembly synthesis process, which results in a hierarchical structure that consists of microscale papillae comprising numerous nanorods. The papillae have diameters ranging from 2 to 4 microns and the nanorods have diameters in the 35-45 nanometer range. A growth mechanism based on the vapor liquid-solid mechanism is proposed that accounts for the morphological aspects in the micro- and nano-scales.

Varshney, Deepak↗
DOE OSTI2024

Nanotwinned alloys under high pressure

Nanotwinned alloys are of interest due to their high strength and ductility, but twin boundaries may not be stable under shear. Computational studies indicate that high hydrostatic pressure may suppress detwinning mechanisms. Here, in this study, we investigate the microstructural changes of nanotwinned-nanocrystalline copper-nickel and Inconel 725 alloys under quasi-hydrostatic pressures up to 50 gigapascals (GPa). The alloys are compressed in a diamond anvil cell. In-situ x-ray diffraction (XRD) and ex-situ transmission electron microscopy (TEM) were employed to monitor microstructural changes. Twin boundary deformation and grain growth occur at 11.4 GPa quasi-hydrostatic pressure in the copper-nickel alloy. Molecular dynamics (MD) simulations reveal that hydrostatic pressure causes elevated local shear stress at grain boundaries, which leads to atomic rearrangements. A superposition of hydrostatic and deviatoric pressures lead to partial dislocation mediated twin boundary migration. In contrast, the Inconel 725 alloy showed stable twin and grain boundaries up to a quasi-hydrostatic pressure of 12.7 GPa. Texture, high solid solution strengthening, and low stacking fault energy are hypothesized to the enhanced microstructural stability in Inconel 725.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Silicon Ingot Casting - Heat Exchanger Method Multi-wire Slicing - Fixed Abrasive Slicing Technique. Phase 3 Silicon Sheet Growth Development for the Large Area Sheet Task of the Low-cost Solar Array Project

Several 20 cm diameter silicon ingots, up to 6.3 kg. were cast with good crystallinity. The graphite heat zone can be purified by heating it to high temperatures in vacuum. This is important in reducing costs and purification of large parts. Electroplated wires with 45 um synthetic diamonds and 30 um natural diamonds showed good cutting efficiency and lifetime. During slicing of a 10 cm x 10 cm workpiece, jerky motion occurred in the feed and rocking mechanisms. This problem is corrected and modifications were made to reduce the weight of the bladeheat by 50%.

Schmid, F.↗
DOE OSTI2025

Multi-scale Interaction Mechanism for Edge-Localized-Mode Suppression in the Tokamak Edge

A central challenge in fusion energy is reconciling the high-confinement mode required for reactor performance with the intense intermittent relaxation events it produces, known as edge-localized modes. These instabilities arise in the steep pressure pedestal at the plasma edge when magnetohydrodynamic thresholds are crossed, inflicting damaging heat loads on reactor components. Here, we show that multiscale interactions between microscopic turbulence and macroscopic magnetohydrodynamic modes provide encouraging prospects for self-organized edge-localized modes regulation. Using direct quantitative measurements of multiscale modes, eddy dynamics, and turbulent flux, we show that small-scale electron drift wave turbulence actively scatters the large-scale peeling-ballooning modes. This scattering decorrelates the pressure and velocity fields of the instability, so arresting its growth. Our modeling and theoretical analysis confirm this suppression mechanism is effective even when conventional linear stability thresholds are exceeded. This work establishes a nonlinear principle for edge-localized modes stability, revealing how ambient micro-turbulence can be leveraged to maintain a macro-stable, high-performance pedestal for future fusion reactors.

experimental nuclear physics↗
DOE OSTI2021

Physics of turbulence spreading and explicit nonlocality

In this paper, we systematically derive a model for turbulence spreading from the basic kinetic equation. The model contains explicit nonlocal nonlinear diffusion and nonlocal growth. When the nonlocality scale parameter δ b (banana width) vanishes, this model reduces to the usual turbulence spreading model. We elucidate the mechanisms of nonlinear saturation and nonlocal growth. Results show that nonlocal effects, especially the nonlocal growth, thicken the turbulence spreading front and increase the speed of front propagation. More turbulence intensity penetrates the stable region when δ b increases. The penetration depth Δ p is proportional to $ \delta_b/L_T $, therefore the fraction of turbulence in the unstable region scales as 1 – δ b* . Lastly, the transport scales the same way.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Engineering quantum-coherent defects: The role of substrate miscut in chemical vapor deposition diamond growth

The engineering of defects in diamond, particularly nitrogen-vacancy (NV) centers, is important for many applications in quantum science. A materials science approach based on chemical vapor deposition (CVD) growth of diamond and in situ nitrogen doping is a promising path toward tuning and optimizing the desired properties of the embedded defects. Herein, with the coherence of the embedded defects in mind, we explore the effects of substrate miscut on the diamond growth rate, nitrogen density, and hillock defect density, and we report an optimal angle range for the purposes of engineering coherent ensembles of NV centers in diamond according to our growth parameters. We provide a model that quantitatively describes hillock nucleation in the step-flow regime of CVD growth, shedding insight on the physics of hillock formation. We also report significantly enhanced incorporation of nitrogen at hillock defects, opening the possibility for templating hillock-defect-localized NV center ensembles for quantum applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2000

Diagnostic Techniques Used to Study Chemical-Vapor-Deposited Diamond Films

The advantages and utility of chemical-vapor-deposited (CVD) diamond as an industrial ceramic can only be realized if the price and quality are right. Until recently, this technology was of interest only to the academic and basic research community. However, interest has grown because of advances made by leading CVD diamond suppliers: 1) Reduction of the cost of CVD polycrystalline diamond deposition below $5/carat ($8/sq cm); 2) Installation of production capacity; 3) Epitaxial growth of CVD single-crystal diamond. Thus, CVD diamond applications and business are an industrial reality. At present, CVD diamond is produced in the form of coatings or wafers. CVD diamond film technology offers a broader technological potential than do natural and high-pressure synthetic diamonds because size, geometry, and eventually cost will not be as limiting. Now that they are cost effective, diamond coatings - with their extreme properties - can be used in a variety of applications. Diamond coatings can improve many of the surface properties of engineering substrate materials, including erosion, corrosion, and wear resistance. Examples of actual and potential applications, from microelectromechanical systems to the wear parts of diamond coatings and related superhard coatings are described. For example, diamond coatings can be used as a chemical and mechanical barrier for the space shuttles check valves, particularly on the guide pins and seat assemblies.

Miyoshi, Kazuhisa↗
NASA NTRS2001

Microgravity Production of Nanoparticles of Novel Materials Using Plasma Synthesis

The research goal is to study the formation in reduced gravity of high quality nanoparticulate of novel materials using plasma synthesis. Particular emphasis will be placed on the production of powders of non-oxide materials like diamond, SiC, SiN, c-BN, etc. The objective of the study is to investigate the effect of gravity on plasma synthesis of these materials, and to determine how the microgravity synthesis can improve the quality and yield of the nanoparticles. It is expected that the reduced gravity will aid in the understanding of the controlling mechanisms of plasma synthesis, and will increase the yield, and quality of the synthesized powder. These materials have properties of interest in several industrial applications, such as high temperature load bearings or high speed metal machining. Furthermore, because of the nano-meter size of the particulate produced in this process, they have specific application in the fabrication of MEMS based combustion systems, and in the development and growth of nano-systems and nano-structures of these materials. These are rapidly advancing research areas, and there is a great need for high quality nanoparticles of different materials. One of the primary systems of interest in the project will be gas-phase synthesis of nanopowder of non-oxide materials.

Frenklach, Michael↗
NASA NTRS1982

Large-area silicon sheet task

A set of computer models was used to define a growth system configuration that was then built and used to grow web with lower thermally generated stress. Aspects of research in the edge-defined film-fed growth (EFG) method of making Si ribbon are reported. A technique was developed to determine base resistivity and carrier lifetime in semicrystalline wafers. Automated growth of 150 kg of 15 cm-dia ingot material per crucible is reviewed. Scanning transmisson electron microscopy (STEM) and microprobe investigations of processed EFG ribbon are reported. The chemical composition of the large precipitates was studied. The structural arrangement and the electrical activity of distentions or close to the central twin plane in processed material were studied. The electrical and structural properties of grain boundaries in silicon are discussed. Temperature-dependence measurements of zero-bias conductance, a photoconductivity technique, and deep-level transient spectroscopy (DLTS) were developed. A grooving and staining technique, secondary ion mass spectroscopy, and EBIC measurements in scanning electron microscopy were used to study enhanced diffusion of phosphorus at grain boundaries in polycrystaline silicon. The fundamental mechanisms of abrasion and wear and the deformation of Si by a diamond in various fluid environments are described. The efficiency of solar cells made from EFG ribbon and Semix Inc. material is reported.

Morrison, A. D.↗
DOE OSTI2024

An exploration of anomalous electrical noise in shocked cyclotrimethylenetrinitramine (RDX)-based explosives

Gas gun shock experiments on cyclotrimethylenetrinitramine (RDX)-based explosive compositions that employ embedded gauge particle velocity tracers have noted a significant amount of electrical noise when compared to other explosive formulations. This paper reexamines previously published embedded gauge data on Cyclotols (60–80 wt. % RDX) to quantify the electromagnetic behavior of these materials. The primary observation is a fourfold increase in the electrical noise when Cyclotols are shocked above 4.22 ± 0.08 GPa. Electromagnetic gauge noise is also observed within particle velocity traces in reactive growth and off-Hugoniot shocks, although at higher pressures than the direct shock case, suggesting a temperature- or kinetically dependent transition. In all cases, the electrical noise disappears upon detonation. By comparing with the static high-pressure phase diagram of RDX, we interpret this change in electromagnetic behavior to be a change in the RDX crystal structure to a piezoelectric phase, although it is uncertain whether the γ or ε phase is responsible for the observed behavior.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Evidence and modeling of turbulence bifurcation in L-mode confinement transitions on Alcator C-Mod

Analysis and modeling of rotation reversal hysteresis experiments show that a single turbulent bifurcation is responsible for the Linear to Saturated Ohmic Confinement (LOC/SOC) transition and concomitant intrinsic rotation reversal on Alcator C-Mod. Plasmas on either side of the reversal exhibit different toroidal rotation profiles and therefore different turbulence characteristics despite the profiles of density and temperature, which are indistinguishable within measurement uncertainty. Elements of this bifurcation are also shown to persist for auxiliary heated L-modes. The deactivation of subdominant (in the linear growth rate and contribution to heat transport) ion temperature gradient and trapped electron mode instabilities is identified as the only possible change in turbulence within a reduced quasilinear transport model across the reversal, which is consistent with the measured profiles and inferred heat and particle fluxes. Experimental constraints on a possible change from strong to weak turbulence, outside the description of the quasilinear model, are also discussed. These results indicate an explanation for the LOC/SOC transition that provides a mechanism for the hysteresis through the dynamics of subdominant modes and changes in their relative populations and does not involve a change in the most linearly unstable ion-scale drift-wave instability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Growth and passivation of individual carbon nanoparticles by C2H2 addition at high temperatures: Dependence of growth rate and evolution on material and size

Absolute kinetics for reactions of C2H2 with a series of ∼60 individual carbon nanoparticles (NPs) from graphite, graphene, graphene oxide, carbon black, diamond, and nano-onion feedstocks were measured for temperatures (TNP) ranging from 1200 to 1700 K. All the NPs were observed to gain mass by carbon addition under conditions that varied with feedstock but with large variations in initial growth rate. Long reaction periods were studied to allow the evolution of growth rates over time to be observed. Diamond NPs were found to passivate against C2H2 addition if heated above ∼1400 K, and the highly variable initial reactivity for carbon nano-onions was found to depend on the presence of non-onion-structure surface carbon. For graphitic and carbon black NPs, three distinct growth modes were observed, correlated with the initial NP mass (Minitial). Smallest graphitic and carbon black NPs, with masses <∼25 MDa, initially grew rapidly but also passivated quickly after adding <4% of Minitial. NPs in the 20–50 MDa range also passivated but only after multiple waves of fast growth separated by periods of low reactivity, with up to ∼11% total mass gain before passivation. The largest carbon black and graphitic NPs, with Minitial >50 MDa, grew rapidly and continuously, adding up to ∼300% of Minitial with no sign of rate slowing as long as C2H2 was present. The efficiencies for C2H2 addition and etching by O2 are strongly correlated, but the correlation changes as the NPs passivate. Growth and passivation mechanisms are discussed.

Chemistry↗
NASA NTRS2003

Nucleation Behavior of Oxygen-Acetylene Torch-Produced Diamond Films

A mechanism is presented for the nucleation of diamond in the combustion flame environment. A series of six experiments and two associated simulations provide results from which the mechanism was derived. A substantial portion of the prior literature was reviewed and the data and conclusions from the previous experimenters were found to support the proposed mechanism. The nucleation mechanism builds on the work of previous researchers but presents an approach to nucleation in a detail and direction not fully presented heretofore. This work identifies the gas phase as the controlling environment for the initial formation steps leading to nucleation. The developed mechanism explains some of the difficulty which has been found in producing single crystal epitaxial films. An experiment which modified the initial gas phase precursor using methane and carbon monoxide is presented. Addition of methane into the precursor gases was found to be responsible for pillaring of the films. Atomic force microscopy surface roughness data provides a reasonable look at suppression of nucleation by carbon monoxide. Surface finish data was taken on crystals which were open to the nucleation environment and generally parallel to the substrate surface. The test surfaces were measured as an independent measure of the instantaneous nucleation environent. A gas flow and substrate experiment changed the conditions on the surface of the sample by increasing the gas flow rate while remaining on a consistent point of the atomic constituent diagram, and by changing the carbide potential of the substrate. Two tip modification experiments looked at the behavior of gas phase nucleation by modifying the shape and behavior of the flame plasma in which the diamond nucleation is suspected to occur. Diamond nucleation and growth was additionally examined using a high-velocity oxygen fuel gun and C3H6 as the fuel gas phase precursor with addition of carbon monoxide gas 01 addition of liquid toluene.

Roberts, F. E.↗
NASA NTRS2003

Carbon-Based Wear Coatings: Properties and Applications

The technical function of numerous engineering systems - such as vehicles, machines, and instruments - depends on the processes of motion and on the surface systems. Many processes in nature and technology depend on the motion and dynamic behavior of solids, liquids, and gases. Smart surface systems are essential because of the recent technological push toward higher speeds, loads, and operating temperatures; longer life; lighter weight and smaller size (including nanotechnology); and harsh environments in mechanical, mechatronic, and biomechanical systems. If proper attention is not given to surface systems, then vehicles, machines, instruments, and other technical systems could have short lives, consume excessive energy, experience breakdowns, result in liabilities, and fail to accomplish their missions. Surface systems strongly affect our national economy and our lifestyles. At the NASA Glenn Research Center, we believe that proper attention to surface systems, especially in education, research, and application, could lead to economic savings of between 1.3 and 1.6 percent of the gross domestic product. Wear coatings and surface systems continue to experience rapid growth as new coating and surface engineering technologies are discovered, more cost-effective coating and surface engineering solutions are developed, and marketers aggressively pursue, uncover, and exploit new applications for engineered surface systems in cutting tools and wear components. Wear coatings and smart surface systems have been used widely in industrial, consumer, automotive, aerospace, and biomedical applications. This presentation expresses the author's views of and insights into smart surface systems in wear coatings. A revolution is taking place in carbon science and technology. Diamond, an allotrope of carbon, joins graphite, fullerenes, and nanotubes as its major pure carbon structures. It has a unique combination of extreme properties: hardness and abrasion resistance; adhesion and friction; thermal conductivity; chemical and thermal inertness; corrosion and wear resistance; radiation resistance and biocompatibility; electronic, acoustic, and electrochemical characteristics; and environmental compatibility. These properties make diamond attractive for a wide range of diverse applications. In particular, chemical-vapor-deposited (CVD) diamond coatings offer a broad potential, since size and cost are not as limiting. The production of large, superhard diamond films or sheets at low cost make designer materials possible. This presentation is divided into two sections: properties and applications of hard coatings. The first section is concerned with the fundamental properties of the surfaces of CVD diamonds and related materials. The surface properties of hard coatings with favorable coefficients of friction (less than or equal to 0.1) and dimensional wear coefficients (less than or equal to 10(exp -6) cubic millimeters/N.m) in specific environments are discussed. The second section is devoted to applications. Examples of actual, successful applications and of potential challenging applications of the coatings.such as CVD diamond, diamondlike carbon, and cubic boron nitride-are described. Cutting tools coated with CVD diamond are of immediate commercial interest. Other applications, such as microelectromechanical systems (MEMS), valves, and bearings of CVD diamond, are being developed, but at a slow pace. There is a continually growing interest in commercializing diamondlike carbon for wear parts applications, such as biomedical parts and implants, forming dies, transport guides, magnetic tapes and disks, valves, and gears. Cubic boron nitride films are receiving attention because they can be used on tools to machine ferrous materials or on wear parts in sliding contact with ferrous materials.

Miyoshi, Kazuhisa↗
DOE OSTI2023

On how fast ions enhance the regulation of drift wave turbulence by zonal flows

Abstract This paper presents a mechanism for enhanced regulation of drift wave turbulence by zonal flows in the presence of a fast ion population. It demonstrates that dilution effects due to the energetic particles (EPs) have a far-reaching impact on all aspects of the nonlinear dynamics. The modulational growth of zonal flow shear and the corresponding evolution of drift wave energy are calculated with dilution effects. The coupled zonal flow growth and drift wave energy equations are reduced to a predator–prey model. This is solved for the fixed points, which represents the various states of the system. Results display a strong dependence on dilution, which leads to greatly reduced levels of saturated turbulence and transport. Implications for the FIRE mode plasma of KSTAR are discussed in detail. This model is perhaps the simplest dynamical one which captures the beneficial effects of EPs on confinement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Magnetic imaging and statistical analysis of the metamagnetic phase transition of FeRh with electron spins in diamond

Magnetic imaging based on nitrogen-vacancy (NV) centers in diamond has emerged as a powerful tool for probing magnetic phenomena in fields ranging from biology to physics. A key strength of NV sensing is its local-probe nature, enabling high-resolution spatial images of magnetic stray fields emanating from a sample. However, this local character can also form a drawback for analyzing the global properties of a system, such as a phase transition temperature. Here, we address this challenge by using statistical analyses of magnetic-field maps to characterize the first-order temperature-driven metamagnetic phase transition from the antiferromagnetic to the ferromagnetic state in FeRh. After imaging the phase transition and identifying the regimes of nucleation, growth, and coalescence of ferromagnetic domains, we statistically characterize the spatial magnetic-field maps to extract the transition temperature and thermal hysteresis width. By analyzing the spatial correlations of the maps in relation to the magnetocrystalline anisotropy and external magnetic field, we detect a reorientation of domain walls across the phase transition. The employed statistical approach can be extended to the study of other magnetic phenomena with NV magnetometry or other sensing techniques.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Creation of depth-confined, shallow nitrogen-vacancy centers in diamond with tunable density

Engineering shallow nitrogen-vacancy (NV) centers in diamond holds the key to unlocking new advances in nanoscale quantum sensing. We find that the creation of near-surface NVs through delta doping during diamond growth allows for tunable control over both NV depth confinement (with a twofold improvement relative to low-energy ion implantation) and NV density, ultimately resulting in highly sensitive single defects and ensembles with coherence limited by NV–NV interactions. Additionally, we demonstrate the utility of our shallow delta-doped NVs by imaging magnetism in few-layer CrSBr, a two-dimensional magnet. Here, we anticipate that the control afforded by near-surface delta doping will enable new developments in NV quantum sensing from nanoscale nuclear magnetic resonance to entanglement-enhanced metrology.

Chemical vapor deposition↗