Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

SAS 3 observations of Cygnus X-1 - The intensity dips

In general, the dips are observed to occur near superior conjunctions of the X-ray source, but one pair of 2-minute dips occurs when the X-ray source is closer to the observer than is the supergiant companion. The dips are analyzed spectrally with the aid of seven energy channels in the range 1.2-50 keV. Essentially, there is no change in the spectral index during the dips. Reductions in the count rates are observed at energies exceeding 6 keV for some of the dips, but the dip amplitude is always significantly greater in the 1.2-3 keV band. It is believed that absorption by partially ionized gas may best explain these results, since the observations of Pravdo et al. (1980) rule out absorption by unionized material. Estimates for the intervening gas density, extent, and distance from the X-ray source are presented. Attention is also given to the problems confronting the models for the injection of gas through the line of sight, believed to be inclined by approximately 30 deg from the binary pole.

Remillard, R. A.↗

ASCA Observation of the Dipping X-Ray Source X1916-053

We present the results of timing and spectral studies of the dipping X-ray source X1916-053, observed by ASCA during its Performance Verification phase. The detected dipping activity is consistent with previous observations, with a period of 3008s and an intermittent secondary dip observed roughly 0.4 out of phase with the primary dip. The energy spectra of different intensity states are fitted with a power law with partial covering fraction absorption and interstellar absorption. The increase in the hardness ratio during the primary and secondary dips, and the increase in the covering fraction and column density with decreasing X-ray intensity, all imply that the dipping is caused by the photo-absorbing materials which have been suggested to be where the accreted flow hits the outer edge of the disk materials. The spectra at all intensity levels show no apparent evidence for Fe or Ne emission lines. This may be due to the low metal abundance in the accretion flow. Alternatively, the X-ray luminosity of the central source may be too weak to excite emission lines, which are assumed to be produced by X-ray photoionization of the disk materials.

Ko, Yuan-Kuen↗

A Coordinated RXTE/ASCA Study of Absorption Dips in Circinus X-1 at Phase Zero

This proposal was for an Rossi X Ray Timing Explorer (RXTE) study of Circinus X-1 with the ASCA satellite for the purpose of studying the iron emission feature during intensity dips. These dips had been discovered previously with ASCA and they appeared to vary in equivalent width and in the energy of the iron K edge. Proper analyses requires good continuum measurements which Rossi X Ray Timing Explorer/Proportional Counter Array (RXTE/PCA) could provide. Also, the PCA data would show any temporal evolution correlated with spectral evolution. RXTE provided 90 ks of data during March 3-5, 1998 which included phase zero which is where the dips usually take place. The ASCA observations were taken by Dr. Neil Brandt of Penn State University. Unfortunately, the source intensity showed far less dipping activity than is typical near phase zero. The light curve exhibited only very narrow sporadic dips rather than some long deep dips necessary for sufficient statistics in the ASCA and RXTE instruments for spectral studies. This prevented us from carrying out the primary goal of the proposal.

Bradt, Hale↗

DIPS-Plus: The enhanced database of interacting protein structures for interface prediction

Abstract In this work, we expand on a dataset recently introduced for protein interface prediction (PIP), the Database of Interacting Protein Structures (DIPS), to present DIPS-Plus, an enhanced, feature-rich dataset of 42,112 complexes for machine learning of protein interfaces. While the original DIPS dataset contains only the Cartesian coordinates for atoms contained in the protein complex along with their types, DIPS-Plus contains multiple residue-level features including surface proximities, half-sphere amino acid compositions, and new profile hidden Markov model (HMM)-based sequence features for each amino acid, providing researchers a curated feature bank for training protein interface prediction methods. We demonstrate through rigorous benchmarks that training an existing state-of-the-art (SOTA) model for PIP on DIPS-Plus yields new SOTA results, surpassing the performance of some of the latest models trained on residue-level and atom-level encodings of protein complexes to date.

59 BASIC BIOLOGICAL SCIENCES↗

A STUDY OF THE LOW-MASS X-RAY BINARY DIP SOURCES XB 1916 - 053, XB 1323 - 619, X 1624 - 490 AND 4U 1746 - 371 OBSERVED WITH INTEGRAL

We detect dipping activity/modulations in the light curve of the four low-mass X-ray binaries in the 3-10 keV and 20-40 keV energy ranges. The spectral parameters derived from the fits to the International Gamma-Ray Astrophysics Laboratory data are consistent with hot coronal structures in these systems where we find a range of plasma temperatures 3.0-224.9 keV. The unabsorbed X-ray to soft gamma-ray fluxes between 4 keV and 200 keV are 5.9 x 10{sup -10} erg s{sup -1} cm{sup -2} for XB 1916 - 053, 3.3 x 10{sup -10} erg s{sup -1} cm{sup -2} for XB 1323 - 619, 21.6 x 10{sup -10} erg s{sup -1} cm{sup -2} for X 1624 - 490, and 11.0 x 10{sup -10} erg s{sup -1} cm{sup -2} for 4U 1746 - 371. The optical depth to Compton scattering, {tau}, varies in a range 4.4-0.002 consistent with electron densities n {sub e} < 1.4 x 10{sup 15} cm{sup -3}. In general, we find no significant difference in the dip and non-dip spectra in the ISGRI energy range (above 20 keV) for all the four sources. We only detect absorption differences between dipping and non-dipping intervals for XB 1916 - 053 and X 1624 - 490 in the JEM-X energy range. Fits in the 4-200 keV range including an additional photoionized absorber model for the two sources show that XB 1916 - 053 has the highest ionized absorber among the two.

79 ASTRONOMY AND ASTROPHYSICS↗

X-RAY DIPS IN THE SEYFERT GALAXY FAIRALL 9: COMPTON-THICK 'COMETS' OR A FAILED RADIO GALAXY?

We investigate the spectral variability of the Seyfert galaxy Fairall 9 using almost 6 years of monitoring with the Rossi X-ray Timing Explorer with an approximate time resolution of 4 days. We discover the existence of pronounced and sharp dips in the X-ray flux, with a rapid decline of the 2-20 keV flux of a factor of two or more followed by a recovery to pre-dip fluxes after {approx}10 days. These dips skew the flux distribution away from the commonly observed lognormal distribution. Dips may result from the eclipse of the central X-ray source by broad-line region clouds, as has recently been found in NGC 1365 and Mrk 766. Unlike these other examples, however, the clouds in Fairall 9 would need to be Compton-thick, and the non-dip state is remarkably free of any absorption features. A particularly intriguing alternative is that the accretion disk is undergoing the same cycle of disruption/ejection as seen in the accretion disks of broad-line radio galaxies such as 3C120 but, for some reason, fails to create a relativistic jet. This suggests that a detailed comparison of Fairall 9 and 3C120 with future high-quality data may hold the key to understanding the formation of relativistic jets in active galactic nucleus.

79 ASTRONOMY AND ASTROPHYSICS↗

A DIP AFTER THE EARLY EMISSION OF SUPERLUMINOUS SUPERNOVAE: A SIGNATURE OF SHOCK BREAKOUT WITHIN DENSE CIRCUMSTELLAR MEDIA

The origin of superluminous supernovae (SLSNe), especially the source of their huge luminosities, has not been clarified yet. While a strong interaction between SN ejecta and dense circumstellar media (CSM) is a leading scenario, alternative models have been proposed. In this Letter, we suggest new diagnostics to discriminate the strong SN-CSM interaction scenario from the others: a decline in the luminosity ('dip') before the main peak of the light curve (LC). This dip is an unavoidable consequence of having a dense CSM within which the shock breakout occurs. If a dense CSM shell is located far at large radii from the progenitor inside, it takes time for the SN ejecta to reach it and the early LC can be powered by the SN ejecta before the collision. Once the SN ejecta collides with the dense CSM, the electron density and thus the Thomson scattering opacity suddenly increase. Photons are unable to go out of the shock even if there is a source of emission inside, which results in the dip in the LC. This dip is a solid prediction from the strong interaction scenario irrespective of power source for the early emission. Eventually, the forward shock breaks out from within the dense CSM, and the luminosity increases through continuous strong SN-CSM interaction, resulting in an SLSN. The possible dip observed in the hydrogen-poor SLSN, 2006oz, could be the first example of this signature and give support to the SN-CSM interaction as the power source of SLSN 2006oz.

79 ASTRONOMY AND ASTROPHYSICS↗

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

The technical and economic feasibility of producing solar cell quality sheet silicon by dip-coating one surface of carbonized ceramic substrates with a thin layer of large grain polycrystalline silicon was investigated. The dip-coating methods studied were directed toward a minimum cost process with the ultimate objective of producing solar cells with a conversion efficiency of 10% or greater. The technique shows excellent promise for low cost, labor-saving, scale-up potentialities and would provide an end product of sheet silicon with a rigid and strong supportive backing. An experimental dip-coating facility was designed and constructed, several substrates were successfully dip-coated with areas as large as 25 sq cm and thicknesses of 12 micron to 250 micron. There appears to be no serious limitation on the area of a substrate that could be coated. Of the various substrate materials dip-coated, mullite appears to best satisfy the requirement of the program. An inexpensive process was developed for producing mullite in the desired geometry.

Heaps, J. D.↗

Digital Information Platform (DIP) Request for Information (RFI) Informational Session

DIP published an RFI on March 23, 2021. An information session is being hosted to go over the concept of DIP, review the content of the RFI and clarify what is being asked. Important information is emerging in digital form and additional effort is required to utilize the information. DIP will provide the capability to integrate key data sources to data processing services that are used to build aviation services for the traditional/commercial community and new emergents. DIP is currently planning and will take a community-involved, collaborative approach to define and develop the framework. DIP is seeking community and stakeholder input to operational needs, metrics of interest, and demonstration contribution. Participants will have an opportunity to ask questions at the end.

Mirna Johnson↗

Diffusion of Aluminum Into Steel Substrates By Means Of Hot Dip Aluminizing

Surface coating is an efficient and economical method to obtain desirable material surfaces properties. As compared to other coating techniques, hot dip coating can be considered as the most economical way to protect steel surfaces. Hot dip aluminizing technique was investigated in this study. Experiments have been conducted on the mild steel substrates with 10 mm diameter. The substrates were dipped into the molten aluminum maintained at temperature 750 deg. C for 5, 10, 15, 20, 25 and 30 minutes. Optical microscopy, scanning electron microscope and energy dispersive X-ray spectroscopy were used in this investigation. From the microstructure observation, it showed the appearance of intermetallic layer covered by the top layer of Al on the mild steel substrate increased with the increase in dipping time. The result of EDX analysis revealed the existence of Fe and Al in form of new Al-Fe phase. This indicated the possible formation of the intermetallic layers.

36 MATERIALS SCIENCE↗

Tribology and Tool Wear of Hot Dip Galvanized Zinc Magnesium Alloys on Cold Rolled Steel Sheets

Recently zinc based coatings on cold rolled steel with improved functionality in terms of forming and/or corrosion behaviour have been intensively investigated in the steel industry. One of the most promising products are zinc magnesium alloys produced in hot dip galvanizing process. These coatings were already introduced in construction industry a few years ago. With some modifications the improved properties of the coating are also interesting for automotive industry. In the present work the tribological potential of hot dip galvanized zinc magnesium coatings (HDG/ZM) produced at an industrial line under regular production, was studied in terms of sliding properties, adhesive and abrasive tool wear.First a short introduction into surface morphology of HDG/ZM will be given. For the tribological characterization of the material, which is the main topic of the contribution, different tests were performed on hot dip galvanised zinc magnesium material and results were compared with classic hot dip galvanized zinc coating (HDG/Z). The investigations are mainly based on the strip draw test which allows the determination of the friction coefficient directly by using a constant contact pressure. Deep drawing property was tested by forming model cups. The abrasive tool wear was tested using a standard test for material used in automotive industry. The adhesive tool wear was investigated by characterizing the coating material transferred to the tool in the strip draw test.All performed tests show an improved drawability of HDG/ZM compared to classical HDG/Z reference material. However the most promising difference between HDG/ZM and HDG/Z is that galling was found to be less for HDG/ZM than for HDG/Z. Therefore HDG/ZM is an interesting system not only with respect to corrosion protection but also in terms of tribology and provides clear advantages in formability.

36 MATERIALS SCIENCE↗

Digital Information Platform (DIP) Overview

On March 24, 2021, NASA’s Digital Information Platform (DIP) released a Request for Information (RFI) to the aviation community. The RFI was intended to request two things: 1) DIP concept input such as current challenges and needs for data and services and 2) Interest in participating in collaborative demonstrations. On July 29, 2021, DIP team will meet with Airlines for America (A4A) to share a summary of information received from the RFI responses. The objective of the meeting is to follow up with respondents with takeaways the DIP team identified that will inform the concept and demonstration plans. The forum will give participants an opportunity to add on and provide feedback to the summary. The meeting will also describe the roadmap for the Collaborative Demonstrations and next steps for partner engagement.

Digital Information Platform (DIP) RFI summary↗

Elevated temperature ductility dip in an additively manufactured Al-Cu-Ce alloy

The deformation and failure mechanisms of Al-9Cu-6Ce (wt%) based alloys fabricated with laser powder bed fusion were investigated from room temperature to 400°C. The yield and ultimate tensile strengths decreased monotonically with increase in temperature, but the tensile elongation dipped unexpectedly at elevated temperatures and exhibited a minimum at 300°C. The dip in tensile elongation occurred with a concomitant dip in strain-rate sensitivity (SRS) of deformation. The as-fabricated alloy microstructure was heterogeneous, and the heat affected zone (HAZ) underneath the melt pool boundary was prone to strain localization. At 300 °C, the reduced SRS promoted the progression of strain localization in the HAZ leading to failure initiation and the dip in tensile elongation. Furthermore, a higher SRS or strain-hardening rate at other temperatures improved the tensile elongation by slowing the progression of strain localization in the HAZ such that failure initiated by other mechanisms elsewhere in the microstructure. Notably, the tensile elongation was limited by the defect structure only in a narrow temperature range (150 - 200 °C) while at other temperatures it was limited by the inherent microstructural features. This investigation exemplifies unexpected deformation and failure mechanisms possible in heterogeneous microstructures that result from additive manufacturing.

36 MATERIALS SCIENCE↗

Directly imaging steeply-dipping fault zones in geothermal fields with multicomponent seismic data

For characterizing geothermal systems, it is important to have clear images of steeply-dipping fault zones because they may confine the boundaries of geothermal reservoirs and influence hydrothermal flow. Elastic reverse-time migration (ERTM) is the most promising tool for subsurface imaging with multicomponent seismic data. However, conventional ERTM usually generates significant artifacts caused by the cross correlation of undesired wavefields and the polarity reversal of shear waves. In addition, it is difficult for conventional ERTM to directly image steeply-dipping fault zones. We develop a new ERTM imaging method in this paper to reduce these artifacts and directly image steeply-dipping fault zones. In our new ERTM method, forward-propagated source wavefields and backward-propagated receiver wavefields are decomposed into compressional (P) and shear (S) components. Furthermore, each component of these wavefields is separated into left- and right-going, or downgoing and upgoing waves. The cross correlation imaging condition is applied to the separated wavefields along opposite propagation directions. For converted waves (P-to-S or S-to-P), the polarity correction is applied to the separated wavefields based on the analysis of Poynting vectors. Numerical imaging examples of synthetic seismic data demonstrate that our new ERTM method produces high-resolution images of steeply-dipping fault zones.

58 GEOSCIENCES↗

FROM X-RAY DIPS TO ECLIPSE: WITNESSING DISK REFORMATION IN THE RECURRENT NOVA U Sco

The tenth recorded outburst of the recurrent eclipsing nova U Sco was observed simultaneously in X-ray, UV, and optical by XMM-Newton on days 22.9 and 34.9 after the outburst. Two full passages of the companion in front of the nova ejecta were observed, as was the reformation of the accretion disk. On day 22.9, we observed smooth eclipses in UV and optical but deep dips in the X-ray light curve that disappeared by day 34.9, yielding clean eclipses in all bands. X-ray dips can be caused by clumpy absorbing material that intersects the line of sight while moving along highly elliptical trajectories. Cold material from the companion could explain the absence of dips in UV and optical light. The disappearance of X-ray dips before day 34.9 implies significant progress in the formation of the disk. The X-ray spectra contain photospheric continuum emission plus strong emission lines, but no clear absorption lines. Both continuum and emission lines in the X-ray spectra indicate a temperature increase from day 22.9 to day 34.9. We find clear evidence in the spectra and light curves for Thompson scattering of the photospheric emission from the white dwarf. Photospheric absorption lines can be smeared out during scattering in a plasma of fast electrons. We also find spectral signatures of resonant line scattering that lead to the observation of the strong emission lines. Their dominance could be a general phenomenon in high-inclination systems such as Cal 87.

79 ASTRONOMY AND ASTROPHYSICS↗

Characterisation of the dip-bump structure observed in proton–proton elastic scattering at $\sqrt{s}$ = 8 TeV

The TOTEM collaboration at the CERN LHC has measured the differential cross-section of elastic proton–proton scattering at √s = 8TeV in the squared four-momentum transfer range 0.2GeV 2 < |t| < 1.9GeV 2 . This interval includes the structure with a diffractive minimum (“dip”) and a secondary maximum (“bump”) that has also been observed at all other LHC energies, where measurements were made. A detailed characterisation of this structure for √s = 8 TeV yields the positions, |t| dip = (0.521 ± 0.007)GeV 2 and |t| bump = (0.695 ± 0.026)GeV 2 , as well as the cross-section values, dσ/dt| dip = (15.1 ± 2.5)μb/GeV 2 and dσ/dt| bump = (29.7 ± 1.8)μb/GeV 2 , for the dip and the bump, respectively.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

BORON ABUNDANCES ACROSS THE “Li–Be DIP” IN THE HYADES CLUSTER

Dramatic deficiencies of Li in the mid-F dwarf stars of the Hyades cluster were discovered by Boesgaard and Tripicco. Boesgaard and King discovered corresponding, but smaller, deficiencies in Be in the same narrow temperature region in the Hyades. Using the Space Telescope Imaging Spectrograph on the Hubble Space Telescope , we investigate B abundances in the Hyades F stars to look for a potential B dip using the B i resonance line at 2496.8 Å. The light elements Li, Be, and B are destroyed inside stars at increasingly hotter temperatures: 2.5, 3.5, and 5 × 10{sup 6} K, respectively. Consequently, these elements survive to increasingly greater depths in a star and their surface abundances indicate the depth and thoroughness of mixing in the star. We have (re)determined Li abundances/upper limits for 79 Hyades dwarfs, Be for 43 stars, and B for 5 stars. We find evidence for a small drop in the B abundance across the Li–Be dip. The B abundances for the four stars in the temperature range 6100–6730 K fit the B–Be correlation found previously by Boesgaard et al. Models of rotational mixing produce good agreement with the relative depletions of Be and B in the dip region. We have compared our nLTE B abundances for the three high B stars on either side of the Li–Be dip with those found by Duncan et al. for the two Hyades giants. This confirms the factor of 10 decline in the B abundance in the Hyades giants as predicted by dilution due to the deepening of the surface convection zone.

79 ASTRONOMY AND ASTROPHYSICS↗

Anelastic response of the earth to a dip slip earthquake

The deformation induced by a vertical dip slip earthquake is examined using a variety of rheologic models. In this way the complications of dipping faults are avoided, and the phenomenon of transient peripheral warping is clearly revealed. A thrust fault dipping at 30 deg is investigated, and the important effects of dip and the existence of a slab on the asymmetry of strain pulses propagated into the overthrust and subducted lithosphere are demonstrated. One of the signal results of the study is the essential similarity of the strain patterns for Newtonian and non-Newtonian flow laws: the two rheologies give nearly identical strain field geometries. The principal difference between the two, which is readily observable, is in their time evolution. Relaxation in non-Newtonian rheologies tends to be initially fast, then slow at times that are late in comparison with relaxation in a Newtonian rheology. The possibility of simply recalling the time dependence of a Newtonian solution to obtain an approximate solution to a non-Newtonian problem is demonstrated.

Melosh, H. J.↗