Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffuser Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

An approximate analysis of the diffusing flow in a self-controlled heat pipe.

Constant-density two-dimensional axisymmetric equations are presented for the diffusing flow of a class of self-controlled heat pipes. The analysis is restricted to the vapor space. Condensation of the vapor is related to its mass fraction at the wall by the gas kinetic formula. The Karman-Pohlhausen integral method is applied to obtain approximate solutions. Solutions are presented for a water heat pipe with neon control gas.

Somogyi, D.↗

Calculations of Diffuser Flows with an Anisotropic K-Epsilon Model

A newly developed anisotropic K-epsilon model is applied to calculate three axisymmetric diffuser flows with or without separation. The new model uses a quadratic stress-strain relation and satisfies the realizability conditions, i.e., it ensures both the positivity of the turbulent normal stresses and the Schwarz' inequality between any fluctuating velocities. Calculations are carried out with a finite-element method. A second-order accurate, bounded convection scheme and sufficiently fine grids are used to ensure numerical credibility of the solutions. The standard K-epsilon model is also used in order to highlight the performance of the new model. Comparison with the experimental data shows that the anisotropic K-epsilon model performs consistently better than does the standard K-epsilon model in all of the three test cases.

Zhu, J.↗

A computational study of radiation and gravity effect on temperature and soot formation in a methane air co-flow diffusion flame

An effort has been made for a quantitative assessment of the soot formed under steady state in a methane air co flow diffusion flame by a numerical simulation at normal gravity and at lower gravity levels of 0.5 G, 0.1 G and 0.0001 G (microgravity). The peak temperature at microgravity is reduced by about 50 K than that at normal gravity level. There is an augmentation of soot formation at lower gravity levels. Peak value at microgravity multiplies by a factor of ∼7 of that at normal gravity. However, if radiation is not considered, soot formation is found to be much more.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental determination of the velocity and strain rate field in a laminar H2/Air counter-flow diffusion flame via LDA

Measurements of the axial and radial components of velocity on the air side of stagnation in an axisymmetric H2/Air laminar counter-flow diffusion flame are reported. Results include the two-dimensional velocity field and computed velocity gradients (strain rates) along the stagnation streamline at two 'characteristic' strain rates, below the extinction limit. The measurements generally verify the modeling assumptions appropriate to the model of Kee et al. (1988). The 'traditional' potential flow model is not consistent with the measured results.

Yeo, S. H.↗

AEROICESTUDY Colorado State University Continuous Flow Diffusion Chamber (CFDC) version R0

This dataset comprises measurements of atmospheric ice nucleating particle (INP) number concentrations at ARM's Southern Great Plains (SGP) Site Guest Instrument Facility (GIF), in Lamont, Oklahoma, during the 2019 Aerosol-Ice Formation Closure Pilot Study (AEROICESTUDY). The results reported here are from the Colorado State University Continuous Flow Diffusion Chamber (CFDC-1H) and represent real-time measurements of ambient INPs.

54 ENVIRONMENTAL SCIENCES↗

A new method for operating a continuous flow diffusion chamber to investigate immersion freezing: assessment and performance study

Glaciation in mixed-phase clouds predominately occurs through the immersion freezing mode where ice nucleating particles (INPs) immersed within supercooled droplets induce nucleation of ice. Currently, model representations of this process are a large source of uncertainty in simulating cloud radiative properties, and to constrain these estimates, continuous flow diffusion chamber (CFDC)-style INP devices are commonly used to assess the immersion freezing efficiencies of INPs. In this study, a new approach was explored to operating such an ice chamber that provides maximum activation of particles without droplet breakthrough and correction factor ambiguity to obtain high-quality INP measurements in a manner that has not been demonstrated as possible previously. The conditioning section of the chamber was maintained at ~ –20 °C and water relative humidity (RH w ) ~ 113 % conditions to maximize the droplet activation, and the droplets were supercooled with an independently temperature-controlled nucleation section at a steady cooling rate (0.5 °C min –1 ) to induce the freezing of droplets and evaporation of unfrozen droplets. The performance of the modified ice chamber was evaluated using four INP species: K-feldspar, illite-NX, Argentinian soil dust, and airborne arable dust that had shown ice nucleation over a wide span of supercooled temperatures. Dry dispersed and size-selected K-feldspar particles were generated in the laboratory. Illite-NX and soil dust particles were sampled during the second phase of the Fifth International Ice Nucleation Workshop (FIN-02) campaign, and airborne arable dust particles were sampled from the aerosol inlet located on the rooftop of the laboratory. The measured ice nucleation efficiencies of model aerosols with a surface active site density (n s ) metric were higher, but mostly agreed within one order of magnitude compared to literature results.

54 ENVIRONMENTAL SCIENCES↗

A new method for operating a continuous-flow diffusion chamber to investigate immersion freezing: assessment and performance study

Abstract. Glaciation in mixed-phase clouds predominantly occurs through the immersion-freezing mode where ice-nucleating particles (INPs) immersed within supercooled droplets induce the nucleation of ice. Model representations of this process currently are a large source of uncertainty in simulating cloud radiative properties, so to constrain these estimates, continuous-flow diffusion chamber (CFDC)-style INP devices are commonly used to assess the immersion-freezing efficiencies of INPs. This study explored a new approach to operating such an ice chamber that provides maximum activation of particles without droplet breakthrough and correction factor ambiguity to obtain high-quality INP measurements in a manner that previously had not been demonstrated to be possible. The conditioning section of the chamber was maintained at −20 ∘C and water relative humidity (RHw) conditions of 113 % to maximize the droplet activation, and the droplets were supercooled with an independently temperature-controlled nucleation section at a steady cooling rate (0.5 ∘C min−1) to induce the freezing of droplets and evaporation of unfrozen droplets. The performance of the modified compact ice chamber (MCIC) was evaluated using four INP species: K-feldspar, illite-NX, Argentinian soil dust, and airborne soil dusts from an arable region that had shown ice nucleation over a wide span of supercooled temperatures. Dry-dispersed and size-selected K-feldspar particles were generated in the laboratory. Illite-NX and soil dust particles were sampled during the second phase of the Fifth International Ice Nucleation Workshop (FIN-02) campaign, and airborne soil dust particles were sampled from an ambient aerosol inlet. The measured ice nucleation efficiencies of model aerosols that had a surface active site density (ns) metric were higher but mostly agreed within 1 order of magnitude compared to results reported in the literature.

54 ENVIRONMENTAL SCIENCES↗

Source of the Bursty Bulk Flow Diffuse Aurora: Electrostatic Cyclotron Harmonic and Whistler Waves in the Coupling of Bursty Bulk Flows to Auroral Precipitation

Electron cyclotron harmonic (ECH) and whistler chorus waves are recognized as the two mechanisms responsible for the resonant wave‐particle interactions necessary to precipitate plasma sheet electrons into the ionosphere, producing the diffuse Aurora. Previous work has demonstrated ECH waves dominate electron scattering at L shells >8, while whistler chorus dominates scattering at L shells L < 8. However, we find from Time History of Events and Macroscale (THEMIS) Interactions during Substorms observations of fast flows at L = 12 that oblique whistler chorus emissions play the dominant role in scattering electrons. Previous works have identified whistler‐mode waves within fast flows that are produced by an electron temperature anisotropy Te,⊥/Te,||> 1, consistent with electron betatron acceleration. Here, however, we find whistler chorus emissions throughout an interval of fast flows where Te,⊥/Te,||< 1. Parallel electron beams account for the enhanced parallel electron temperature and serve as the instability mechanism for the whistler chorus. The parallel electron beams and associated cigar‐shaped distributions are consistent with Fermi acceleration at dipolarizations in fast flows. We demonstrate that the scattering efficiency of the whistler chorus exceeds that of ECH waves, which THEMIS also detects during the fast flows. The obliquity of the whistler waves permits efficient scattering of lower‐energy electrons into the diffuse aurora. We conclude that Fermi acceleration of electrons provides one important free‐energy source for the wave‐particle interactions responsible for coupling plasma sheet electrons into the diffuse aurora during substorm conditions.

Wendel, D. E.↗

Effects of interstage diffuser flow distortion on the performance of a 15.41-centimeter tip diameter axial power turbine

The performance of a variable-area stator, axial flow power turbine was determined in a cold-air component research rig for two inlet duct configurations. The two ducts were an interstage diffuser duct and an accelerated-flow inlet duct which produced stator inlet boundary layer flow blockages of 11 percent and 3 percent, respectively. Turbine blade total efficiency at design point was measured to be 5.3 percent greater with the accelerated-flow inlet duct installed due to the reduction in inlet blockage. Blade component measurements show that of this performance improvement, 35 percent occurred in the stator and 65 percent occurred in the rotor. Analysis of inlet duct internal flow using an Axisymmetric Diffuser Duct Code (ADD Code) were in substantial agreement with the test data.

Mclallin, K. L.↗

Effects of interstage diffuser flow distortion on the performance of a 15.41-centimeter tip diameter axial power turbine

The performance of a variable-area stator, axial flow power turbine was determined in a cold-air component research rig for two inlet duct configurations. The two ducts were an interstage diffuser duct and an accelerated-flow inlet duct which produced stator inlet boundary layer flow blockages of 11 percent and 3 percent, respectively. Turbine blade total efficiency at design point was measured to be 5.3 percent greater with the accelerated-flow inlet duct installed due to the reduction in inlet blockage. Blade component measurements show that of this performance improvement, 35 percent occurred in the stator and 65 percent occurred in the rotor. Analysis of inlet duct internal flow using an Axisymmetric Diffuser Duct Code (ADD Code) were in substantial agreement with the test data.

Mclallin, K. L.↗

Experimental and analytical study of a conically diffused flow with a nearly separated boundary layer

Turbulence measurements were obtained in the nearly separated flow in a 13 deg total angle of divergence conical diffuser coupled to a constant area tailpipe. Air at 207 newtons per square centimeter and 308 K provided an inlet velocity of about 51 meters per second at an inlet unit Reynolds number of 63.7 million per meter. Very high longitudinal turbulence intensities accompanied the diffusion process with peak values approaching 40 percent when normalized by the local centerline velocity. Predictions of the pressure recovery coefficient using a mixing length concept were good in the early stages of diffusion. In the latter stages of diffusion satisfactory predictions of the pressure recovery were obtained with an empirical method.

Boldman, D. R.↗

Effects of vane-induced rotation on diffuser flow distortion in an axisymmetric mixed-compression inlet

An investigation of vane-induced flow rotation to modify distorted steady-state total-pressure patterns in the subsonic diffuser of a supersonic mixed-compression inlet was conducted. Radial static-pressure gradients generated by the rotation was the mechanism used to modify the total-pressure distributions. Significant redistribution of circumferential distortion patterns into more compatible radial patterns was realized, but flow problems near the duct walls reduced the general effectiveness of the technique. Total-pressure losses associated with the swirl vanes were slight. Limited turbulence data indicated that vane istallation resulted in reduced turbulence levels.

Meleason, E. T.↗

CARS thermometry in laminar sooting ethylene-air co-flow diffusion flames with nitrogen dilution

Temperature measurements were performed in nonpremixed, sooting jet flames using coherent anti-Stokes Raman scattering (CARS). The jet fluid was ethylene diluted with different concentrations of nitrogen, and the co-flow fluid was dry air. The flames were stabilized on a Yale burner, also known as Smooke/Long burner, and the operating conditions were chosen to match previous experiments on the burner by the Yale group and other research groups. The selected flames have also been identified as target flames by the International Sooting Flame Workshop. CARS measurements of temperature provide insight into the structure of these sooting flames and serve as benchmark data for comparison with computations. A dual-pump vibrational CARS system was used here in order to avoid soot interferences. We were able to obtain high quality CARS spectra in all regions of the flame including the highly sooting regions and near the exit of the fuel nozzle, where the nonresonant modulation of the nitrogen CARS spectrum is strong due to the high ethylene concentrations. The measurements are compared with CFD results in literature and discussed in context of measured soot volume fraction, also, from literature.

42 ENGINEERING↗

Effect of ammonia addition on suppressing soot formation in methane co-flow diffusion flames

Due to issues surrounding carbon dioxide emissions from carbon-containing fuels, there is growing interest in ammonia (NH 3 ) as an alternative combustion fuel. One attractive method of burning NH 3 is to co-fire it with hydrocarbons, such as natural gas, and in this case soot formation is possible. To begin understanding the influence of NH 3 on soot formation when co-fired with hydrocarbons, soot volume fractions and mole fractions of gas-phase species were computationally and experimentally interrogated for CH 4 flames with up to 40% NH 3 by volumetric fuel fraction. Mole fractions of gas-phase species, including C 2 H 2 and C 6 H 6 , were measured with on-line electron impact mass spectrometry, and soot volume fractions were obtained via color-ratio pyrometry. The simulations employed a detailed chemical mechanism developed for capturing nitrogen interactions with hydrocarbons during combustion. The results are compared to findings in N 2 -CH 4 flames, in order to separate thermal and dilution effects from the chemical influence of NH 3 on soot formation. Experimentally, C 2 H 2 concentrations were found to decrease slightly for the NH 3 -CH 4 flames relative to N 2 -CH 4 flames, and a stronger suppression of C 6 H 6 was found for NH 3 relative to N 2 additions. The measured results show a strong suppression of soot with the addition of NH 3 , with soot concentrations reduced by over a factor of 10 with addition of up to 20% or more NH 3 by mole fraction. The model satisfactorily captured relative differences in maximum centerline C 2 H 2 , C 6 H 6 , and soot concentrations with addition of N 2 , but was unable to match measured differences in NH 3 -CH 4 flames. Furthermore, these results highlight the need for an improved understanding of fuel-nitrogen interactions with higher hydrocarbons to enable accurate models for predicting particulate emissions from NH 3 /hydrocarbon combustion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Performance of the continuous flow diffusion chambers

A brief comparative description is made of the chambers. Overall, comparisons for the various types of experiments - monodisperse, polydisperse and ambient aerosol - showed agreement among these chambers to within 15% in most cases. A careful analysis of the results indicated that a proper accounting of certain parameters would bring about much closer agreement among four of these instruments.

Hudson, J. G.↗

An experimental study of opposed flow diffusion flame extinction over a thin fuel in microgravity

The flame spread and flame extinction characteristics of a thin fuel burning in a low-speed forced convective environment in microgravity were examined. The flame spread rate was observed to decrease both with decreasing ambient oxygen concentration as well as decreasing free stream velocity. A new mode of flame extinction was observed, caused by either of two means: keeping the free stream velocity constant and decreasing the oxygen concentration, or keeping the oxygen concentration constant and decreasing the free stream velocity. This extinction is called quenching extinction. By combining this data together with a previous microgravity quiescent flame study and normal-gravity blowoff extinction data, a flammability map was constructed with molar percentage oxygen and characteristic relative velocity as coordinates. The Damkohler number is not sufficient to predict flame spread and extinction in the near quench limit region.

Ferkul, Paul V.↗