SEARCH · Search NASA

Results for “Dimethyl ether (DME)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2025

DME-to-Propane Mixture Effects on a Light Duty Compression Ignition Engine

Fuels that can be produced in a sustainable manner are of high interest because they can provide an essential step toward net zero emissions vehicles. This study examines the combustion of two such fuels, Dimethyl Ether (DME) and propane, in a compression ignition, 4-cylinder, 2.2L engine running with mixtures of DME-to-Propane ranging of 100%-0%, 85%-15%, 75%-25%, and 65%-35% by weight. Testing was conducted at 2000rpm - 100Nm, an important representative point in the FTP certification cycle. For each fuel mixture, conditions tested include sweeps of boost, EGR and injection pressure. Here, tests are mainly conducted at a constant combustion timing with CA10 of -1 deg with respect to TDC, with an engine controller combustion feedback system based on in-cylinder sampling of pressure. Trends of NOx, HC, and CO are similar for the range of DME-to-propane, from 100%-0% to 75%-25%. Boost and injection pressures had the most notable impact on the heat release traces. Higher boost, from stoichiometric to lean resulted in approximately a 3-5% increase on cycle efficiency. Fuel injection pressures resulted in about 1% gain per 200bar. Results also illustrated that EGR is effective in reducing NOx but causes notable degradation of cycle efficiency. The emissions for DME-propane mixtures with 65%-35% had a different trend, with CO and HC exceeding the runs with lower propane content by 2 to 3-fold. As propane content increases, the pressure rise rates become higher, and with 65%-35% mixtures, rates easily exceed 12bar/deg. The increased rise rates correlate with early injection timings but the rates can be reduced, with higher boost and lower injection pressures. The result of the approach, however, leads to lower thermal efficiencies, decreasing efficiency by over 5% between neat DME and the highest propane ratios.

Combustion and combustion processes↗

DOE OSTI2023

Kinetics and extinction of non-premixed cool and warm flames of dimethyl ether at elevated pressure

Here, the growing demand of clean and efficient propulsion and energy systems has sparked an interest in understanding low-temperature combustion at high pressure. Cool flame transition and extinction limits as well as oxygen concentration dependence at elevated pressures provide insights of the low-temperature and high-pressure fuel reactivity. A new experimental high-pressure counterflow burner platform was designed and developed to achieve the studies of high-pressure cool flames. Dimethyl ether (DME) was chosen to study its non-premixed cool flame in high-pressure counterflow burner at pressure up to 5 atm, perhaps for the first time. This paper investigates the effects of pressure on cool flame structure, extinction and transition limits, and oxygen concentration dependence as well as ozone assisted warm flames of DME in experiments and numerical simulations. The results show that the reignition transition from cool flame to hot flame occurs either with the decrease of the strain rate at a given fuel concentration and pressure or with the increase of fuel mole fraction or pressure at a given strain rate. Furthermore, it is shown that the higher pressure shifts the cool flame to higher strain rates and results in higher cool flame extinction strain rates. However, the existing kinetic model of DME fails in predicting the cool flame extinction limit at elevated pressures. Besides, the cool flame extinction limits are proportional to nth power of the oxygen concentration, [O 2 ] n , and the increase of pressure leads to stronger extinction limit dependence (larger n) on oxygen concentration. The present experiment and detailed kinetic analysis show clearly that increasing pressure promotes the low-temperature chemistry including the oxygen addition reactions. In addition, stable warm flame was first experimentally observed by using DME at elevated pressure with ozone sensitization.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2026

Effect of NO on DME-Methanol HCCI Experimental Observations

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) and successful ignition methanol at diesel–like timescales. However, if the preburn species are treated separately from the complete methanol MCCI approach the preburn heat release rate (HRR) phasing and behavior do not replicate the preburn behavior of the complete approach. Thus, the presence of the main methanol mixing controlled compression ignition (MCCI) combustion event influences the DME/methanol preburn kinetics. Specifically, it was found that trapped residual temperature alone was insufficient alone to be responsible for the observed differences, and that trace species concentrations of NO in the trapped residual gas also influenced DME/methanol kinetics increasing low temperature heat release (LTHR) magnitude and advancing high temperature heat release (HTHR) phasing. NO is not present in HCCI combustion of neat DME or DME/methanol blends nor is elevated gas temperature in the trapped residuals; both of which result in failure to accurately predict the HCCI combustion of DME/methanol blends when coupled with subsequent DI methanol MCCI. This work experimentally explores the effect of trapped residual temperature and NO on DME and DME/methanol HCCI combustion.

Jatana, Gurneesh [ORNL] (ORCID:0000000288903225)↗

DOE OSTI2026

Effect of NO on DME-Methanol HCCI Combustion Using a Reduced Chemical Kinetics Mechanism

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) mixing controlled compression ignition (MCCI) of neat methanol. Within that context, complementary experimental work found that the influence of combustion residuals on the heat release rate (HRR) was significant, specifically for residual NO. This finding motivated the present computational and kinetic evaluation of the effects of NO on the low (LTHR) and high (HTHR) temperature heat release rates. The strong influence of small quantities of NO on the combustion process of a DME/methanol/H2O mixture (low catalyst or reactor efficiency) necessitated a kinetics-based investigation into this phenomenon. A mechanism sourced from the existing literature with NO had 172 species and 1375 reactions, making it computationally expensive for use. Hence, a mechanism reduction effort was implemented, and a rate constant (k) tuning effort based on sensitivity analysis was needed to validate experimental results using a zero-dimensional engine model in Cantera. The reduced mechanism was able to successfully capture the negligible influence of NO addition on DME HCCI combustion, whereas an advancement in LTHR and HTHR for a DME/methanol/H2O mixture was kinetically confirmed. Reaction pathway analysis showed that addition of NO chemically counteracted the OH sink created by alcohols like methanol, increasing the effectiveness of DME ignition.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗

DOE OSTI2025

Extraction of Oil From Camelina Seeds Using Liquefied Dimethyl Ether

With a changing climate and a push for net-zero carbon emissions, sustainable aviation fuel (SAF) is gaining interest worldwide. Due to its compatibility with current infrastructure and potential to reduce emissions by up to 94%, SAF has been identified as the best near-term opportunity to decrease carbon emissions in the aviation industry. SAF can be produced from various renewable feedstocks, with Camelina sativa (L.) seeds standing out due to their high oil content. Conventionally, the oil is extracted using hydrothermal liquefaction (HTL), which involves the pressurized heating of water and biomass up to 400°C, making it incredibly energy-intensive. Conversely, liquefied dimethyl ether (DME) extraction operates at room temperature and is capable of near 100% solvent recycling. In this work, we propose the use of DME extraction as a substitute for HTL, hypothesizing that it can overcome the challenges of current oil extraction methods while maintaining the same oil yields.

09 - BIOMASS FUELS↗

DOE OSTI2021

Spectroscopic insight into carbon speciation and removal on a Cu/BEA catalyst during renewable high-octane hydrocarbon synthesis

Conversion of methanol and dimethyl ether (DME) to high-octane gasoline catalyzed by beta zeolite (BEA) provides an opportunity for the production of high-quality fuels from renewable carbon sources (e.g., gasified biomass). Recent research demonstrated that a Cu-modified BEA zeolite catalyst (Cu/BEA) offered advantages over the unmodified BEA catalyst due to multifunctional Cu species that enabled incorporation of co-fed H2, reactivation of light alkanes, and reduction of products from the aromatic hydrocarbon pool. The shift in hydrocarbon pool chemistry has the potential to influence the identity and relative composition of surface carbon species that are often linked to deactivation. A detailed understanding of these carbon species is important to develop an effective and efficient regeneration procedure that can enable the transition from fundamental catalyst development to commercial application. Here, we applied complementary ex situ and in situ characterization techniques to compare the structures of surface carbon species on post-reaction Cu/BEA and unmodified BEA catalysts. Both catalysts contained acyclic and aromatic hydrocarbons along with graphitic carbon species. However, the post-reaction Cu/BEA catalyst had a lower polycyclic aromatic content, and further, the graphitic species were more hydrogenated and defective. It was also found that the presence of Cu promoted carbon removal at lower temperatures than for unmodified BEA through activation of O2 by Cu oxide during thermal oxidation. The fundamental insight into the composition of surface carbon species enabled the design of an effective and efficient regeneration strategy for the DME homologation reaction over Cu/BEA, resulting in full recovery of the catalyst activity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2022

Plasma thermal-chemical instability of low-temperature dimethyl ether oxidation in a nanosecond-pulsed dielectric barrier discharge

Plasma stability in reactive mixtures is critical for various applications from plasma-assisted combustion to gas conversion. To generate stable and uniform plasmas and control the transition towards filamentation, the underlying physics and chemistry need a further look. Here, this work investigates the plasma thermal-chemical instability triggered by dimethyl-ether (DME) low-temperature oxidation in a repetitive nanosecond pulsed dielectric barrier discharge. First, a plasma-combustion kinetic mechanism of DME/air is developed and validated using temperature and ignition delay time measurements in quasi-uniform plasmas. Then the multi-stage dynamics of thermal-chemical instability is experimentally explored: the DME/air discharge was initially uniform, then contracted to filaments, and finally became uniform again before ignition. By performing chemistry modeling and analyzing the local thermal balance, it is found that such nonlinear development of the thermal-chemical instability is controlled by the competition between plasma-enhanced low-temperature heat release and the increasing thermal diffusion at higher temperature. Further thermal-chemical mode analysis identifies the chemical origin of this instability as DME low-temperature chemistry. This work connects experiment measurements with theoretical analysis of plasma thermal-chemical instability and sheds light on future chemical control of the plasma uniformity.

repetitive nanosecond pulses↗

DOE OSTI2024

Light Duty Engine Performance Characteristics with Dimethyl Ether and Propane

Here, this paper explores the performance characteristics of a compression ignition HYUNDAI 2.2L engine operating with Dimethyl Ether (DME). Test are carried out at three operating conditions that weigh heavily in the FTP75 certification cycle (1000rpm-12Nm, 1500rpm-50Nm, 2000rpm-100Nm). The engine features a high-pressure common rail fuel injection system designed to operate with liquified gases. The main component of the fuel system is a high-pressure pump that incorporates an electronic inlet metering valve commanded on a crank-angle base to control the rail pressure. The pump, which requires no pressure regulator, provides the flow needed to the injectors without flow returning to the inlet. This novel fueling system is leveraged in tests that are conducted to examine the impact of EGR, combustion phasing, injection pressure on efficiency and emissions. In addition, the impact of introducing 15% Propane by mass is examined. During the tests, the engine ECU is aided by an Engine Controller High Speed Oversight unit (ECHO) to provide combustion phasing control, improved cylinder-to-cylinder uniformity, and an effective optimization over the testing effort. The use of DME and Propane allowed for peak thermal efficiency of nearly 43%. These fuels enable significant carbon index (CI) reductions over the baseline Diesel fuel, with indications that 50% reduction in CO 2 over the Diesel engine are possible.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2024

Harnessing dimethyl ether with ultra-low-grade heat for scaling-resistant brine concentration and fractional crystallization

Solvent-driven separations may enable scalable concentration of hypersaline brines, supporting a circular resource economy from the extraction of lithium and rare earth elements from spent battery and magnet leachates. This work analyses a novel solvent-driven water extraction (SDWE) system employing dimethyl ether (DME) and ultra-low-grade heat for brine concentration and fractional crystallization. SDWE exploits DME’s unique properties: (1) a low dielectric constant that promotes water solubility over charged solutes by a factor of 10 3 , and (2) a high volatility that facilitate efficient DME reconcentration with ultra-low-grade heat. The techno-economic viability of SDWE is assessed with a computational framework that encompasses a liquid–liquid separator and a solvent concentrator. We integrate the extended universal quasichemical model with the virial equation of state to predict the compositions of the complex three-phase DME-water mixture at vapor–liquid and liquid–liquid equilibrium. Subsequently, we optimize the thermodynamic and economic performance of SDWE, by controlling the interstage flash pressure, heat source temperature, and the number of concentrating stages. DME-based SDWE concentrates an input saline feed to 5.5 M and regenerates over 99 % of the DME using ultra-low-grade heat below 50 °C, with a DME/water selectivity ratio of 125. Here our calculations reveal that optimal performance is achieved at interstage flash pressures of 0.4 – 0.5 bar for heat source temperatures between 323–373 K, with improved exergetic efficiencies at lower temperatures. At a heat source temperature of 323 K and an interstage pressure of 0.489 bar, DME-driven SDWE achieves an optimal thermodynamic efficiency of 20.5 % and a projected specific cost of US$ 1.93 m -3 . These specific costs suggest that SDWE is competitive with commercialized thermal distillation technologies, while mitigating the traditional risks associated with scaling in heat and mass exchangers with hypersaline brines.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Low- and intermediate-temperature oxidation of dimethyl ether up to 100 atm in a supercritical pressure jet-stirred reactor

Understanding the low- and intermediate-temperature oxidation chemistry of oxygenated fuels like dimethyl ether (DME) at high pressure is paramount to the development of advanced engines with low carbon emissions. The supercritical pressure jet-stirred reactor (SP-JSR) recently developed at Princeton provides a new platform for conducting kinetic studies at low and intermediate temperatures at extremely high pressures with a uniform temperature distribution and a short flow residence time. This paper uses the SP-JSR to investigate DME oxidation at equivalence ratios of 0.175, 1.0, and 1.72, for pressures of 10 and 100 atm, and temperatures ranging from 400 to 900 K. The results demonstrate weakened NTC behavior at 100 atm relative to 10 atm due to increased flux through QOOH + O 2 = O 2 QOOH relative to QOOH = 2 CH 2 O + OH at 100 atm. Furthermore, the intermediate-temperature oxidation window is shifted to lower temperatures at 100 atm. The experimental data are compared with several chemical kinetic models from the literature. The existing models are seen to agree quite well with the experimental data at 10 atm. However, the models fail to properly capture the NTC behavior at 100 atm. Reaction pathway analyses indicate that both the low- and intermediate-temperature chemistries are controlled by RO 2 consumption pathways. The reaction rates for several of the important reactions, such as DME + OH = CH 3 OCH 2 + H 2 O, H 2 O 2 (+M) = 2 OH (+M), and 2 HO 2 = 2 OH + O 2 are updated in this work. Furthermore, the updated model improves the predictability for all key species compared to the original model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

A Novel Catalytic Membrane Reactor for DME Synthesis from Renewable Resources

Production of liquid fuels or chemicals from CO 2 (captured from the air or flue gases) and renewable hydrogen presents a new approach to producing clean fuels domestically. While significant progress has been made in the area of renewable electricity generation from solar and wind, a large gap remains with respect to the production of renewable liquid fuels/chemicals. Other processes for producing liquid fuels/chemicals from renewable electricity are constrained by thermodynamic limitations, making them prohibitively expensive and impractical. The team is overcoming these limitations and developing catalytic membrane reactor processes with high yields and low energy penalties. Supported by the Advanced Research Projects Agency-Energy (ARPA-E) of the US Department of Energy (DOE), GTI Energy and partners have been developing a technology for the production of renewable dimethyl ether (DME) from carbon dioxide (CO 2 ) and renewable hydrogen (H 2 ) using a novel catalytic membrane reactor and demonstration of this system at a scale of 1 kg/day. DME is a clean-burning, non-toxic fuel with a high cetane value (55-60), making it an excellent diesel alternative. DME can be stored as a liquid under moderate pressure, eliminating the need for the high-pressure containers used for CNG or cryogenics, as in the case of LNG. DME is also approved as a renewable fuel under the U.S. Environmental Protection Agency’s Renewable Fuels Standard (RFS), making it eligible for Renewable Identification Numbers (RINs) credits. By producing DME through the catalytic conversion of captured CO 2 and renewable H 2 , this process will produce renewable liquid transportation fuel and a means of large-scale utilization of captured CO 2 . In the DME synthesis process, CO 2 and H 2 are fed to a hollow fiber catalytic membrane reactor at 300-600 psig that contains a bi-functional catalyst that combines two reactions, methanol synthesis (CO 2 + 3H 2 → CH 3 OH + H 2 O) and methanol dehydration (2CH 3 OH → CH 3 OCH 3 + H 2 O), into a one-step process to produce DME. The bifunctional catalyst converts methanol to DME, enabling higher overall CO 2 conversion. A Cu/ZnO/ZrO 2 /Al 2 O 3 (CZZA) catalyst is used for methanol synthesis and is coupled with a zeolite catalyst H-ZSM-5 for dehydration. This one-step process intensifies a process that would otherwise require multiple reaction steps. However, combining these two reactions results in increased water production which inhibits catalytic activity. Here, the Na + -gated, water-transport membrane (Science, vol. 367, pp. 667, 2020), removes water in situ, shifting the thermodynamic equilibrium towards product formation while decreasing kinetic inhibition from water adsorption onto the catalyst surface. The Na + gated, water-transport nanochannel membrane showed H 2 O/CO 2 selectivity of 560 at 250 °C and 300 psig for H 2 O/CO 2 /CO/H 2 /MeOH gas mixtures. The selectivities of H 2 O/H 2 , H 2 O/CO, and H 2 O/MeOH were 190, 170, and 80, respectively. In a laboratory-scale membrane reactor, DME synthesis testing using this membrane, a DME production rate of 440 g DME /kg cat /h was achieved at 260 °C and 550 psig. Compared to the packed bed reactor, the CO 2 conversion and DME production rate in the membrane reactor were 80% and three times higher, respectively. A prototype test system (1 kg/day) was designed, constructed, and tested. A DME production rate of 1.31 kg/day and a DME productivity of 360 g/h/kg were achieved in the prototype membrane reactor. Good stability was demonstrated during 150-h continuous operation and multiple startups/shutdowns tests.

10 SYNTHETIC FUELS↗

DOE OSTI2024

Electrically Powered High-Salinity Brine Separation Using Dimethyl Ether

Dewatering highly saline aqueous streams, from mining and geothermal leachates to industrial wastewater, is essential for effective resource recovery and safe disposal. Membraneless water extraction (MWE) uses a low-polarity solvent to separate water from concentrated aqueous solutions. In this study, we design a new MWE that uses dimethyl ether (DME) to selectively extract water from high-salinity brines, leveraging the volatility of DME to achieve rapid solvent recovery. By separating water and dissolved salts at a liquid–liquid interface, MWE minimizes the deleterious effects of scaling on vulnerable membrane and heat exchanger surfaces, reducing the need for extensive pretreatment and expensive materials. We begin by developing a computational framework for a multistage counterflow liquid–liquid contactor, which extracts water into DME, coupled with a multistage solvent regenerator that uses vapor compression to efficiently separate the desalinated water from the DME extractant. Excess Gibbs free energy and equation of state frameworks are used to model fluid phase equilibria in water–DME–sodium chloride (NaCl) mixtures, with interaction parameters estimated from experimental data. Incorporating equilibrium calculations into a system-scale computational model, we examine the performance of MWE using DME for the first time. Our analysis demonstrates that MWE can concentrate seawater desalination brine (>1.0 mol NaCl kg –1 ) to zero-liquid discharge salinities, with an energy consumption of under 50 kW h per m 3 of water extracted with a solvent recovery ratio greater than 99.9%. We highlight the importance of staging the vapor compression process to simultaneously minimize energy consumption while enabling brine concentration and product water solvent contamination. Finally, the thermodynamic framework developed here allows for the robust evaluation of new MWE solvents and systems for critical brine concentration and fractional precipitation applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Plasma-assisted deflagration to detonation transition in a microchannel with fast-frame imaging and hybrid fs/ps coherent anti-Stokes Raman scattering measurements

Our study examines kinetic enhancement by nanosecond dielectric barrier discharge (ns-DBD) plasma on fuellean dimethyl ether (DME), oxygen (O 2 ), and argon (Ar) premixtures during deflagration to detonation transition (DDT) experiments in a microchannel. Non-equilibrium plasma produces active species and radicals and creates fast and slow heating of a mixture to promote ignition due to electronic and vibrational excitation. Experiments have been conducted to examine the influence of the plasma discharge on the premixture and on the resultant deflagration to detonation transition (DDT) onset time and distance through the use of high speed imaging and one-dimensional, two-beam, femtosecond/picosecond, coherent anti-Stokes Raman scattering (CARS). A highspeed camera is used to trace the time histories of flame front position and velocity and to identify the dynamics and onset of DDT. The results show that plasma discharge can nonlinearly affect the onset time and distance of DDT. It is shown that a small number of plasma discharge pulses prior to ignition result in reduced DDT onset time and distance by 60% and 40%, respectively, when compared to the results without pre-excitation by ns discharges. The results also show that an increase of plasma discharge pulses results in an extended DDT onset time and distance of 224% and 94%, respectively. Time history of the deflagration wave speed of DME and the analysis of ignition timescale under the choking condition of the deflagration front suggest low temperature ignition may play a role for DME near the isobaric choking condition of the burned gas and the DDT. Plasmainduced conversion of the reactive mixture was assessed via the O 2 to CO 2 ratio as measured through fs/ps CARS during the DBD discharges. The present experiments demonstrate the ability of non-equilibrium plasma to alter the chemistry of DME/O 2 /Ar premixtures in order to control DDT for applications in advanced propulsion engines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Flame dynamics and kinetic coupling of ammonia and dimethyl-ether in non-premixed cool and warm flames at elevated pressure

Developing advanced low-temperature combustion engines with ammonia-biofuel blends requires a comprehensive understanding of low-temperature flame dynamics and kinetic interactions between ammonia and oxygenated fuels at elevated pressures. This work aims to study the dynamics and kinetics of non-premixed Dimethyl Ether (DME)/Ammonia (NH 3 ) cool and warm flames, and their reignition to hot flames. A counterflow burner is employed to establish DME/NH 3 cool/warm flames at pressures up to 5 atm. The extinction limits of cool flame and the reignition limits of warm flame to hot flame are measured by varying NH 3 concentrations and compared to simulations to quantitatively examine the effects on DME/NH 3 flames. It is found that NH 3 inhibits low-temperature DME oxidation and results in lower cool flame extinction limits. Warm flames in the presence of NH 3 are observed for the first time, revealing a non-monotonic effect of NH 3 addition: a small amount of NH 3 presence enhances warm flame chemistry and promotes reignition to hot flames, while a high NH 3 concentration weakens the warm flame. This trend is further explained by 0-D PSR kinetic simulations and 1-D S-curve flame dynamic calculations. Three flame transition regimes between cool flames (CF), warm flames (WF), and hot flames (HF) by different levels of NH 3 additions at a specific strain rate are identified, namely WFHF reignition, WF-CF transition, and WF extinction. Reaction sensitivity analyses of OH at low temperatures show that NH3 inhibits DME oxidation through OH consumption via H-abstraction and the kinetic couplings of RO 2 /NH 2 , RO 2 /NO x , R/NO x , and O 2 QOOH/NO x further suppress the low-temperature branching. At intermediate-temperatures, NH 2 /NO x /HO 2 coupling promotes warm flames via the pathway NH 2 → H 2 NO → HNO → NO by converting O 2 → HO 2 → OH. At even higher NH₃ concentrations, radical termination reactions of NH 2 + NO/NO 2 and excessive OH consumption via H-abstraction inhibit the flame. The insights into the kinetic coupling between NH 3 and low-temperature chemistry at elevated pressure and its impact on the dynamics of cool-warm-hot flame transitions will contribute to advancing combustion technologies with reduced emissions and improved energy-efficiency.

42 ENGINEERING↗

DOE OSTI2021

Roles of interaction between components in CZZA/HZSM-5 catalyst for dimethyl ether synthesis via CO 2 hydrogenation

The roles of interaction between two catalyst components in CuO–ZnO–ZrO 2 –Al 2 O 3 (CZZA)/HZSM-5 bifunctional catalyst for dimethyl ether (DME) synthesis via carbon dioxide hydrogenation were investigated. It was found that CZZA catalyst showed excellent stability during methanol (MeOH) synthesis for 100 h, while there was a severe loss of catalytic activity in the bifunctional catalyst for DME synthesis. So, the effects of different degrees of intimacy of two catalyst components were studied for DME synthesis, including mixed and separated modes. For the mixed mode, the particle size of catalysts and the amount of reaction intermediates were proven to influence the catalyst deactivation. For the separated mode, the catalysts showed rapid deactivation within a short time. Various characterizations indicated that the remarkable deactivation of separated mode was mainly caused by the decrease of copper active centers (e.g., sintering and oxidation) and blockage of acid sites via increased coke deposition on HZSM-5.

42 ENGINEERING↗

DOE OSTI2022

Superior Metal‐Organic Framework Activation with Dimethyl Ether

Abstract Metal–organic frameworks (MOFs) are demonstrated to be readily activated by treatment with the low surface tension, low boiling point solvent dimethyl ether (DME). The mildness of the method enables access to high surface areas by avoiding structural changes in the framework that often plague thermal activation methods. A distinction from previous methods is that DME activation succeeds for materials with coordinatively unsaturated sites (CUS) and non‐CUS MOFs as well. DME displaces solvent molecules occupying the pores of the MOF as well as those coordinated to metal centers; reducing evacuation temperature by using a coordinating, yet highly volatile guest enables low temperature activation with structural retention as demonstrated surface area measurements that match or exceed existing activation protocols.

Wright, Keenan R.↗

DOE OSTI2022

Superior Metal‐Organic Framework Activation with Dimethyl Ether

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Boosting Hydrogenation of CO 2 Using Cationic Cu Atomically Dispersed on 2D γ‐Al 2 O 3 Nanosheets

The continuous development of novel catalytic approaches is crucial for advancing efficient CO 2 hydrogenation processes. Drawing inspiration from single-atom catalysis and 2D materials, we designed a new 2D single-atom catalyst with excellent thermal stability by thermally treating Cu-adsorbed γ-AlOOH nanosheets, which yielded a Cu/γ-Al 2 O 3 catalyst with high activity in the hydrogenation of CO 2 -yielding methanol (CH 3 OH), dimethyl ether (DME), and CO as products. The active Cu sites are monodispersed and highly stable due to their cationic oxidation state and their substitution for pentacoordinated aluminum (Al P ) sites on particle surfaces. This study demonstrates an efficient approach for achieving a high CO 2 hydrogenation rate (30.45 mol mol −1 h −1 ) using a catalyst system that lacks metallic Cu centers, traditionally considered essential for H₂ dissociation, and employs what was previously thought to be an inert metal oxide (γ-Al 2 O 3 ) for CO and CH 3 OH production. Ongoing mechanistic studies aim to elucidate the synergy between cationic Cu single atoms and γ-Al 2 O 3 , a Lewis acid support, in facilitating hydrogen (H 2 ) activation and methanol formation.

2D catalyst↗