Search NASA⌕ Search

SEARCH · Search NASA

Results for “Discrete element models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Two-Fluid and Discrete Element Modeling of a Parallel Plate Fluidized Bed Heat Exchanger for Concentrating Solar Power

A novel high-temperature particle solar receiver is developed using a light trapping planar cavity configuration. As particles fall through the cavity, the concentrated solar radiation warms the boundaries of the receiver and in turn heats the particles. Particles flow through the system, forming a fluidized bed at the lower section, leaving the system from the bottom at a constant flowrate. Air is introduced to the system as the fluidizing medium to improve particle heat transfer and mixing. A laboratory scale cavity receiver is built by collaborators at the Colorado School of Mines and their data are used for model validation. In this experimental setup, near IR quartz lamp is used to provide flux to the vertical wall of the heat exchanger. The system is modeled using the discrete element method and a continuum two-fluid method. The computational model matches the experimental system size and the particle size distribution is assumed monodisperse. A new continuum conduction model that accounts for the effects of solid concentration is implemented, and the heat flux boundary condition matches the experimental setup. Radiative heat transfer is estimated using a widely used correlation during the post-processing step to determine an overall heat transfer coefficient. The model is validated against testing data and achieves less than 30% discrepancy and a heat transfer coefficient greater than 1000 W/m2 K.

concentrating solar power↗
DOE OSTI2021

Polysiloxane coatings on microspheres based on Multiphase Flow with Interface Exchange-Discrete Element Modelling

Polysiloxane coatings on yttria stabilized zirconia (YSZ) microspheres of 500 μm were simulated in a spout fluidized bed coater using Multiphase Flow with Interface Exchange-Discrete Element Modelling (MFiX-DEM). In this work, two different coater configurations were developed to study the influence of gas velocity and its distribution on particle dynamics. The presence of the Wurster tube not only enhances the distribution but also increases the overall residence time of the particles. Investigations were also carried out with different Wurster tube positions (normal, 10% and 20% lowered from its initial position). Among these, 20% lowered Wurster tube position demonstrated the most effective coating process. The effects of gas inlet pressure on the average gas velocity and the distribution of particles were analyzed. More than 97% of the particles can be retained. The derived results, including average gas velocity, particle retention percentage, and distribution of particles with gas velocity, are being used to guide the experimental work in obtaining defect-free coatings for YSZ microspheres.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Discrete element modeling of irregular-shaped soft pine particle flow in an FT4 powder rheometer

Pine residues are a commonly used biomass feedstock that consists of different anatomical fractions, each with distinct particle characteristics. Here, in this work, an experiment-informed discrete element model is developed to investigate the flowability of pine residues in an FT4 rheometer. Multi-sphere particles with distinct particle attributes are created to model each anatomical fraction type. A systematic analysis of specimens with varying particle characteristics (e.g., anatomical fraction type, particle shape, and size) is conducted to elucidate the relationship between particle attributes and flowability. The results show that stems recorded the highest axial force and torque and, correspondingly, the highest flow energy, which is attributed to their high stiffness and interlocking effect. Increasing their percentage in the mixture increases the flow energy while increasing needles tends to decrease flow energy. Knowledge gained in this study on the flow of anatomical fractions is important for the efficient and robust processing of pine residues.

09 BIOMASS FUELS↗
NASA NTRS2008

Determining Trajectory of Triboelectrically Charged Particles, Using Discrete Element Modeling

The Kennedy Space Center (KSC) Electrostatics and Surface Physics Laboratory is participating in an Innovative Partnership Program (IPP) project with an industry partner to modify a commercial off-the-shelf simulation software product to treat the electrodynamics of particulate systems. Discrete element modeling (DEM) is a numerical technique that can track the dynamics of particle systems. This technique, which was introduced in 1979 for analysis of rock mechanics, was recently refined to include the contact force interaction of particles with arbitrary surfaces and moving machinery. In our work, we endeavor to incorporate electrostatic forces into the DEM calculations to enhance the fidelity of the software and its applicability to (1) particle processes, such as electrophotography, that are greatly affected by electrostatic forces, (2) grain and dust transport, and (3) the study of lunar and Martian regoliths.

Source record↗
DOE OSTI2020

Discrete element modeling of switchgrass particles under compression and rotational shear

Switchgrass is a perennial herbaceous plant regarded as a biomass energy crop in the United States for its highadaptability and yield potential. Processing and handling of switchgrass particles are challenging due to the erratic mechanical and flow behavior originating from their intrinsic particulate properties. Here, we present a bonded-sphere discrete element model designed specifically for switchgrass particles. The model simultaneously captures three key particulate features, i.e., fibrous particle shapes, a wide range of particle sizes, and particle deformability. Realistic yet computationally efficient particle shape templates are created based on the image analysis data of switchgrass specimens. A fitting procedure is proposed to ensure both the particle width and length distributions are captured, a unique requirement for fibrous particles. Two full-scale numerical models, i.e., a uniaxial compression model and a Schulze ring shear model, are developed using information fromphysical experiments. The model is calibrated using experimental data of chopped-small switchgrass specimens, and then, is validated using data of chopped-large specimens in both compression and ring-shear tests. Numerical results show that the numerical models capture bulk densities accurately (with an error of 3%) while slightly underestimate the bulk friction angle. Furthermore, an extensive sensitivity analysis reveals that (1) switchgrass particles with rougher edges (due to different processing techniques) exhibit a higher shear strength and a lower flowability; (2) stiffer particles yield a lower bulk density (up to 21% lower) compared to more deformable particles, indicating particle deformability should be incorporated when modeling biomass flow in a preprocessing system.

09 BIOMASS FUELS↗
DOE OSTI2023

An experiment-informed discrete element modelling study of knife milling for flexural biomass feedstocks

A discrete element method (DEM) based approach is used to study the relationships between material attributes (MAs), processing parameters (PPs), and quality attributes (QAs) for the knife milling of maize stalks. An approximate DEM shape model was conceptualized based on real maize stalks and calibrated based on experimental bending test data for flexural properties (elastic bending stiffness, elastic bending angle limit, elastoplastic ratio, etc.). DEM simulations of maize stalk comminution in a Jordan Reduction Solutions (“JRS”) knife mill were performed to investigate the relationships between the MAs (maize stalk size and breakage stress limit), PPs (impeller rotational speed), and QAs (mass throughput and output particle size distribution (PSD)). The DEM results suggest that stalk length has little influence on mass throughput and PSD, whilst stalks with larger cross sections tend to generate larger sizes of milled particles given the same breakage stress limit. Both the DEM and experimental results show that faster impeller rotation (or higher power) does not necessarily generate higher throughput or smaller output PSD, especially for maize stalks of higher breakage stress limit. The correlations between these MAs, PPs and QAs are found highly stochastic, though breakage stress limit dictates mass throughput, regardless of stalk size. The DEM-predicted output particle size tended to match the experimental data with coarse PSDs based on sieve size but showed weakened fidelity with finer material, indicating the potential for further model improvement.

09 BIOMASS FUELS↗
NASA NTRS2008

Discrete Element Modeling of Triboelectrically Charged Particles

Tribocharging of particles is common in many processes including fine powder handling and mixing, printer toner transport and dust extraction. In a lunar environment with its high vacuum and lack of water, electrostatic forces are an important factor to consider when designing and operating equipment. Dust mitigation and management is critical to safe and predictable performance of people and equipment. The extreme nature of lunar conditions makes it difficult and costly to carry out experiments on earth which are necessary to better understand how particles gather and transfer charge between each other and with equipment surfaces. DEM (Discrete Element Modeling) provides an excellent virtual laboratory for studying tribocharging of particles as well as for design of devices for dust mitigation and for other purposes related to handling and processing of lunar regolith. Theoretical and experimental work has been performed pursuant to incorporating screened Coulombic electrostatic forces into EDEM, a commercial DEM software package. The DEM software is used to model the trajectories of large numbers of particles for industrial particulate handling and processing applications and can be coupled with other solvers and numerical models to calculate particle interaction with surrounding media and force fields. While simple Coulombic force between two particles is well understood, its operation in an ensemble of particles is more complex. When the tribocharging of particles and surfaces due to frictional contact is also considered, it is necessary to consider longer range of interaction of particles in response to electrostatic charging. The standard DEM algorithm accounts for particle mechanical properties and inertia as a function of particle shape and mass. If fluid drag is neglected, then particle dynamics are governed by contact between particles, between particles and equipment surfaces and gravity forces. Consideration of particle charge and any tribocharging and electric field effects requires calculation of the forces due to these effects.

Hogue, Michael D.↗
DOE OSTI2023

Investigation of Best-Practices and Computationally Inexpensive Radiative Exchange Models for Discrete Element Method Modeling of Aluminosilicate Particles in Concentrating Solar Power Environments

Chemically inert, aluminosilicate based particles have been investigated as both a thermal transport and sensible energy storage medium for concentrating solar power facilities. These particles will experience a wide range of operating temperatures (300-1000 K) and handling conditions (dense to dilute falling particle curtains, dense granular flows, or dense structures), requiring specially-designed and optimized infrastructures. The relative influence of collisional and frictional interactions between particles varies based on temperature-dependent particulate properties and greatly impacts the bulk, granular flow behavior. These underlying physics are captured using discrete element method modeling tools. However, this modeling method is computationally expensive as each particle position and interaction is tracked during the simulation. These modeling methods are further complicated by introducing temperature-dependent particle properties, high-temperature radiative exchange, and directional irradiation sources experienced by granular flows in concentrating solar power environments. In this study, coupled experimental and numerical slump testing of aluminosilicate particles was performed and computationally efficient radiative exchange models were evaluated to establish best-practices for discrete element method models for concentrating solar power environments. The three particle types investigated included Carbobead HSP 30 /60, Carbobead CP 30/60, and Granusil 4030. Existing modeling limitations and computationally-efficient multi-modal heat transfer models were evaluated using Aspherix®, a commercial discrete element method software. High-temperature (< 1073 K) slump testing of aluminosilicate particles was performed to investigate the deviation between experimentally-observed and numerically-predicted angles of repose introduced by computation-time reduction practices including the relaxation of the particle elastic modulus and coarse-graining. Coarse-graining is used to use a single modeled particle that is representative of a collection of smaller particles, decreasing the computational cost at the expense of geometric accuracy. Additionally, relaxation of the elastic modulus is used to reduce computational time at the expense of an increased, modeled particle overlap. Prior studies have determined that aluminosilicate particles retain a high elastic modulus at high temperatures (< 1073 K), requiring small simulation timesteps to ensure resolved contact forces resemble appropriate solid mechanics. A parametric study was performed to evaluate the influence of computation time improvements on the deviation between experimental and modeled angle of repose across high temperatures < 1073 K. Additionally, numerical case studies were performed on candidate particle systems at varying porosities and temperatures. These studies were performed to investigate the influence of computationally-efficient radiative-exchange modeling methods coupled to Aspherix® on modeled accuracy and computation time. The recently-developed distance-based approximation was evaluated in estimating radiative exchange between particles and participating surfaces located in close proximity. The distance based approximation was developed to use tabulated estimates of the radiative distribution factor between individual particles and surfaces in close proximity (< 40 particle radii). These methods were expanded to the aluminosilicate particles of interest, including the influence of particle size distributions. To capture radiative exchange between particles and surfaces not in close proximity (> 40 particle radii) and to capture the absorption of directional irradiation from concentrating solar resources, a volumetrically-averaged radiative distribution factor was calculated between the modeled granular flow and surfaces using Monte Carlo ray-tracing for participating media. Volume-averaged absorption and scattering coefficients were predicted using a volumetric discretization of the modeled domain with monodisperse approximations based on geometric optics and experimentally-determined scattering phase functions for aluminosilicate particles.

14 SOLAR ENERGY↗
NASA NTRSDate not supplied

A Framework for Optimization-Based ISRU Tool Design Using Discrete Element Modeling

Novel robotic excavation technologies are needed to perform in-situ resource utilization (ISRU) tasks at levels required to sustain a long-term presence on the lunar surface. Developing and testing multiple iterations of functional hardware is time and cost prohibitive, thus slowing down the pace of progress and delaying humanity’s settlement of the Moon. High-fidelity, physics-based simulation can reduce the time and effort required to develop and deploy robotic systems [1]. We have adopted this approach to create high-fidelity models of robotic test hardware to enable rapid virtual design and optimization of excavation technologies [2]. Such models can leverage modern computational tools like Discrete Element Method (DEM) simulations that can be coupled with automated design approaches like topology optimization to reduce the amount of prototyping and physical testing needed to realize useful tools.

ISRU↗
DOE OSTI2023

Discrete element model for powder grain interactions under high compressive stress

A reduced order, nonlocal model is proposed for the contact force between initially spherical particles under compression. The model in effect provides the normal component of the interaction force between elements in the discrete element method (DEM). It is applicable to high relative density and large stress in powder compaction. It takes into account the mutual interaction between multiple points of contact, in contrast to the usual assumption in DEM of pair interactions. The mathematical form of the model is derived from a variational formulation that leads to the momentum balance for the forces on each grain. The model is calibrated mainly using detailed three dimensional peridynamic simulations of single grains under compressive loading by rigid plates that move radially with prescribed velocity. This calibration takes into account the large deformation and fracture of the grains. The interaction model also includes terms for the unloading behavior and adhesion. Finally, as validation, the model is applied to test data on the compaction of microcrystalline cellulose bulk powder.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Discrete element modeling of deformable pinewood chips in cyclic loading test

The design of efficient lignocellulosic biomass feedstock systems is challenging, as current laboratory characterization and design methods were developed primarily for fine powders with relatively low compressibility. Here, the discrete element method (DEM) is gaining prominence as an alternative method for modeling the bulk flow and transport of particulate materials in hoppers and feeders. However, prior DEM simulations investigating the flow of wood chips modeled the particles as simple rigid geometries such as spheres, rods or blocks, and neglected the effects of particle deformability and irregular shapes. As a consequence, those simplified DEM models may not provide enough key diagnosis to help improve the design of biomass feeding and handling equipment. This work presents a bonded-sphere DEM approach for characterizing the mechanical behavior of bulk flexible, deformable pinewood chips in a cyclic stress loading test. Clustered spheres that can bend and twist via elastic bonds are used to model irregular-shape particles in real pinewood chip samples. An axial compression tester, which contains 0.06 million bonded-sphere particles (1.35 million spheres) in a quarter cylinder, is simulated with a domain size similar to the experiments. With careful calibration, the simulations have delivered the bulk densities and the bulk moduli of elasticity that are in good agreement with those measured in the corresponding experiments. However, it is also been found challenging for the present DEM model to accurately predict the overall stress-strain behavior of bulk pinewood chips, especially the large sustained plastic deformation during unloading. Additional numerical tests have shown that the adjustment in certain contact parameters (e.g. bond stiffness) can lead to profound solution improvement, but meanwhile will induce extra challenges such as increased computing time. Future work will include an elasto-plastic particle bond model to enhance the simulation fidelity.

42 ENGINEERING↗
DOE OSTI2023

Discrete element modeling of granular hopper flow of irregular-shaped deformable particles

Many natural and engineered granular materials have relatively deformable particles. Besides particle size and shape, particle deformability is another salient factor that significantly impacts the material’s flow behavior. Here, in this work, the flow of irregular-shaped deformable particles in a wedge-shaped hopper is investigated using discrete element simulations. A bonded-sphere model is developed to simultaneously capture irregular particle shapes and particle-wise deformations (e.g., compression, deflection, and distortion). Quantitative analysis of the effects of irregular shapes and particle deformations shows that the increase in particle stiffness tends to increase initial packing porosity and decrease the flow rate in the hopper. Rigid particles tend to have clogging issues, whereas deformable particles have less chance to, indicating particle deformation reduces the critical bridging width in the hopper flow. Detailed analysis of stress fields is also conducted to provide insights into the mechanism of particle flow and clogging. Stresses and discharge rates calculated from numerical simulations are compared and show good agreement with Walker’s theory and the extended Beverloo formula. Simulations with various particle shape combinations are also performed and show that the initial packing porosity decreases with an increasing percentage of fibers while the discharge rate has a complex dependency on particle shapes.

09 BIOMASS FUELS↗
DOE OSTI2024

Implementation of the Glued Sphere Discrete Element Model for Non-Spherical Particles in MFiX Software

To enhance solver capabilities, simulation flexibility and model validation within the MFiX software, the U.S. Department of Energy (DOE) is funding efforts to develop and integrate the glued-sphere discrete element method into the latest version of MFiX as a dedicated computational module. The glued-sphere discrete element method is a numerical technique to depict the behavior of non-spherical particles in granular flows or particulate systems by representing them as a collection of component spheres. These spheres are bonded together to approximate the shape and mechanical/chemical properties of a more complex particle. The method effectively reuses the existing sphere-sphere collision algorithm, interphase momentum and heat transfer calculations utilized in the traditional discrete element method, extending these capabilities to non-spherical particles. Additionally, this method explicitly resolves intra-particle temperature and species distributions. The MFiX glued-sphere computational module includes tools for generating glued sphere configurations, a dedicated solver, and visualization capabilities in post-processing. More specifically within the computational module, collision detection and calculations were first performed on component spheres and then mapped onto non-spherical particles. The linear spring-dashpot model was utilized to simulate the sphere-sphere interactions.

Ke, Renjie↗
DOE OSTI2025

Predicting the evolution of biomass bulk density through feedstock preprocessing: Discrete element modeling, regression analysis, and pilot-scale validation

Bulk density is an important material property of biomass feedstocks, influencing handling, storage, transport costs, and conversion efficiency. In this study, predictive regression models for loose and tapped bulk densities of Alamo and Cave-in-Rock switchgrass are developed using a comprehensive dataset generated via calibrated bonded-sphere discrete element method (DEM) simulations. Here, a key contribution of this study is the use of a DEM-based approach, which correlates density with moisture content and particle size distribution parameters and enables analysis across a continuous particle size range, overcoming limitations of purely experimental data. For comparison, regression models are also developed using only experimental data from pilot-scale runs at the Biomass Feedstock National User Facility at Idaho National Laboratory. Validation against pilot-scale data showed reasonable prediction accuracy for both model types, particularly for smaller particle sizes (post-secondary grinding). While the experimental model showed slightly better performance matching the validation data in some cases, the DEM-based model benefits from a much larger dataset, reduced predictor multicollinearity, and continuous parameter coverage, highlighting the utility of validated simulation models for developing robust predictive tools for biomass preprocessing applications.

09 - BIOMASS FUELS↗
DOE OSTI2022

Detailed biomass fast pyrolysis kinetics integrated to computational fluid dynamic (CFD) and discrete element modeling framework: Predicting product yields at the bench-scale

Fast pyrolysis is an intricate process due to the variability and anisotropy of lignocellulosic biomass and the complicated chemistry and physics during conversion in a bubbling fluidized bed reactor (BFBR). The complexity of biomass fast pyrolysis lends itself well to computational fluid dynamics (CFD) and discrete element (DEM) analysis, which promises to reduce experimental time and its associated cost. This work investigated switchgrass fast pyrolysis simulated by computational fluid dynamics coupled with a discrete element method to track individual reacting biomass particles throughout a bench-scale BFBR reactor. We accounted for the fast pyrolysis chemistry through a comprehensive reaction scheme with secondary cracking reactions. We performed a three-step reduction for secondary cracking reactions to convert the full cracking scheme into a reduced scheme easily incorporated into our model. We assessed the impact of operational conditions on the steady-state yields of liquid bio-oil, non-condensable gases (NCG), at 550 °C over a range of fluidization numbers (2 – 6 Umf), reported as a ratio to the minimum fluidization velocity (Umf). At steady-state, the volatile bio-oil yield had a range of 49.3–50.4 wt%. Levoglucosan was the primary volatile component present with 21 wt% of the bio-oil while water was the second largest with 20 wt%. The reduction of the secondary reaction schemes did not appreciably affect the overall yields of switchgrass pyrolysis compared to the full secondary scheme.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2022

Investigating Particle-Particle Electrostatic Effects on Charged Lunar Dust Transport via Discrete Element Modeling

NASA surface exploration missions have always seen negative effects of dust including the Apollo missions. The astronaut-witnessed unusual behavior of the dust particles that surround the vehicle after engine cutoff has the potential to have more of an influence on surface systems dust loading than the high velocity lunar rocket plume ejecta in the landing process. The levitation and transport of the fine components of regolith on lunar surface has been linked to electrostatic effects and electric field, but so far there is no accurate model considering the inter-particle electrostatic interactions, especially when the particles are charged by rocket plume or other mechanical interactions due to exploration activities. This study is proposed to investigate the dynamics of charged lunar regolith with a discrete element method (DEM) approach focusing on the inter-particle interactions and contact charge transfer. The grain dynamics is coupled with mechanical and electrical particle interactions, and both short- and long-range interactions between spherical particles are incorporated. A tribo-charging model based on instantaneous collisions between particles is adopted and validated by comparing the simulation results to existing experimental data. Sensitivity analysis is conducted to quantify the effects of initial charge, tribo-charging, and E-field on transport of lunar dust based on JSC-1 simulants with a radius of 50 lm. DEM simulations are also conducted in a near realistic lunar environment with the estimations of initial conditions that shows the difference in position and velocity distributions between charged particles and uncharged particles. The results indicate that the charged dust particles have higher dispersion of position and velocity by several orders of magnitude due to electrostatic effects. This provides a potential explanation for the phenomena of the approximately 30 s dust lofting following Apollo Lunar Module landing.

Lunar dust↗