Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES, LIQUID-COOLED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

The Aerodynamic Characteristics of Six Full-Scale Propellers Having Different Airfoil Sections

Wind-tunnel tests are reported of six 3-blade 10-foot propellers operated in front of a liquid-cooled engine nacelle. The propellers were identical except for blade airfoil sections, which were: Clark y, R.A.F. 6, NACA 4400, NACA 2400-34, NACA 2rsub200, and NACA 6400. The range of blade angles investigated extended for 15 degrees to 40 degrees for all propellers except the Clark y, for which it extended to 45 degrees. The results showed that the range in maximum efficiency between the highest and lowest values was about 3 percent. The highest efficiencies were for the low-camber sections.

Biermann, David↗
NASA NTRS1939

Tests of Two Full-Scale Propellers with Different Pitch Distributions, at Blade Angles up to 60 Degrees

Two 3-blade 10-foot propellers were operated in front of a liquid-cooled engine nacelle. The propellers differed only in pitch distribution; one had normal distribution (nearly constant pitch for a blade angle of 15 degrees at 0.75 radius), and the other had the pitch of the tip sections decreased with respect to that for the shank sections (blade angle of 35 degrees for nearly constant pitch distribution). Propeller blade angles at 0.75r from 15 degrees to sixty degrees, corresponding to design speeds up to 500 miles per hour, were investigated. Propeller blade angles at 0.75r from 15 degrees to 60 degrees, corresponding to design speeds up to 500 miles per hour, were investigated. The results indicated that the propulsive efficiency at a blade angle of 60 degrees was about 9 percent less than the maximum value of 86 percent, which occurred at blade angle of about 30 degrees. The efficiency at a blade angle of 60 degrees was increased about 7 percent by correcting for the effect of a spinner and, at a blade angle of 30 degrees about 3 percent. The peak efficiencies for the propeller having the washed-out pitch distribution were slightly less than for the normal propeller but the take-off efficiency was generally higher.

Biermann, David↗
NASA NTRS1942

Investigation in the 7-by-10 Foot Wind Tunnel of Ducts for Cooling Radiators within an Airplane Wing

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a large-chord wing model with a duct to house a simulated radiator suitable for a liquid-cooled engine. The duct was expanded to reduce the radiator losses, and the installation of the duct and radiator was made entirely within the wing to reduce form and interference drag. The tests were made using a two-dimensional-flow setup with a full-span duct and radiator. Section aerodynamic characteristics of the basic airfoil are given and also curves showing the characteristics of the various duct-radiator combinations. An expression for efficiency, the primary criterion of merit of any duct, and the effect of the several design parameters of the duct-radiator arrangement are discussed. The problem of throttling is considered and a discussion of the power required for cooling is included.

Harris, Thomas A↗
NASA NTRS1947

The effect of preignition on cylinder temperatures, pressures, power output, and piston failures

An investigation was conducted using a cylinder of a V-type liquid-cooled engine to observe the behavior of the cylinder when operated under preignition conditions. Data were recorded that showed cylinder-head temperatures, time of ignition, engine speed, power output, and change in maximum cylinder pressure as a function of time as the engine entered preignition and was allowed to operate under preignition conditions for a short time. The effects of the following variables on the engine behavior during preignition were investigated: fuel-air ratio, power level, aromatic content of fuel, engine speed, mixture temperature, and preignition source. The power levels at which preignition would cause complete piston failure for the selected engine operating conditions and the types of failure encountered when using various values of clearance between the piston and cylinder barrel were determined. The fuels used had performance numbers high enough to preclude any possibility of knock throughout the test program.

Corrington, Lester C↗
NASA NTRS1938

Investigation in the 7-By-10 Foot Wind Tunnel of Ducts for Cooling Radiators Within an Airplane Wing, Special Report

An investigation was made in the NACA 7- by 10-foot wind tunnel of a large-chord wing model with a duct to house a simulated radiator suitable for a liquid-cooled engine. The duct was expanded to reduce the radiator losses, and the installation of the duct and radiator was made entirely within the wing to reduce form and interference drag. The tests were made using a two-dimensional flow set-up with a full-span duct and radiator. Section aerodynamic characteristics of the basic airfoil are given and also curves showing the characteristics of the various duct-radiator combinations. An expression for efficiency, the primary criterion of merit of any duct, and the effect of the several design parameters of the duct-radiator arrangement are discussed. The problem of throttling is considered and a discussion of the power required for cooling is included. It was found that radiators could be mounted in the wing and efficiently pass enough air for cooling with duct outlets located at any point from 0.25c to 0.70c from the wing leading edge on the upper surface. The duct-inlet position was found to be critical and, for maximum efficiency, had to be at the stagnation point of the airfoil and to change with flight attitude. The flow could be efficiently throttled only by a simultaneous variation of duct inlet and outlet sizes and of inlet position. It was desirable to round both inlet and outlet lips. With certain arrangements of duct, the power required for cooling at high speed was a very low percentage of the engine power.

Harris, Thomas A.↗
NASA NTRS1938

Preliminary Full-Scale Wind-Tunnel Investigation of Wing Ducts for Radiators, Special Report

Wing ducts for liquid-cooled engine radiators have been investigated in the N.A.C.A. full-scale wind tunnel on a large model airplane. Th e tests were made to determine the relative merits of several types of duct and radiator installations for an airplane of a particular des ign. In the test program the principal duct dimensions were system atically varied, and the results are therefore somewhat applicable to the general problems of wing duct design, although they should be co nsidered as preliminary and only indicative of the inherent possibil ities.

Silverstein, Abe↗
NASA NTRS1938

Interrelation of exhaust-gas constituents

This report presents the results of an investigation conducted to determine the interrelation of the constituents of the exhaust gases of internal-combustion engines and the effect of engine performance on these relations. Six single-cylinder, liquid-cooled tests engines and one 9-cylinder radial air-cooled engine were tested. Various types of combustion chambers were used and the engines were operated at compression ratios from 5.1 to 7.0 using spark ignition and from 13.5 to 15.6 using compression ignition. The investigation covered a range of engine speeds from 1,500 to 2,100 r.p.m. The fuels used were two grades of aviation gasoline, auto diesel fuel, and laboratory diesel fuel. Power, friction, and fuel-consumption data were obtained from the single-cylinder engines at the same time that the exhaust-gas samples were collected.

Gerrish, Harold C↗
NASA NTRS1947

Knock-Limited Performance of Triptane and 28-R Fuel Blends as Affected by Changes in Compression Ratio and in Engine Operating Variables

A knock-limited performance investigation was conducted on blends of triptane and 28-P fuel with a 12-cylinder, V-type, liquid-cooled aircraft engine of 1710-cubic-inch displacement at three compression ratios: 6.65, 7.93, and 9.68. At each compression ratio, the effect of changes in temperature of the inlet air to the auxiliary-stage supercharger and in fuel-air ratio were investigated at engine speeds of 2280 and. 3000 rpm. The results show that knock-limited engine performance, as improved by the use of triptane, allowed operation at both take-off and cruising power at a compression ratio of 9.68. At an inlet-air temperature of 60 deg F, an engine speed of 3000 rpm ; and a fuel-air ratio of 0,095 (approximately take-off conditions), a knock-limited engine output of 1500 brake horsepower was possible with 100-percent 28-R fuel at a compression ratio of 6.65; 20-percent triptane was required for the same power output at a compression ratio of 7.93, and 75 percent at a compression ratio of 9.68 allowed an output of 1480 brake horsepower. Knock-limited power output was more sensitive to changes in fuel-air ratio as the engine speed was increased from 2280 to 3000 rpm, as the compression ratio is raised from 6.65 to 9.68, or as the inlet-air temperature is raised from 0 deg to 120 deg F.

Brun, Rinaldo J.↗
NASA NTRS1946

Investigation of Operating Characteristics of an Engine Equipped with Modifications to Eliminate Fuel-Evaporation Icing

Two modified fuel-injection systems, a drilled-inducer type and a spinner type, that prevent serious fuel-evaporation icing were installed on a V-type, liquid-cooled aircraft engine and a preliminary investigation was conducted to determine the effect on engine operating characteristics. The spinner system was also ground - and flight tested on a twin-engine fighter airplane. Flight measurements of cylinder-head temperature over a range of fuel-air ratios and engine power conditions were made at an altitude of approximately 10,000 feet. Starting and accelerating of the engine on the ground were unaffected by the fuel-injection modifications. During the flight investigation, no appreciable variation occurred between the maximum and minimum cylinder-head temperature with the standard and modified system for the same power condition and no irregularity of mixture distribution could be detected throughout the power range of the engine. Normal mixture distribution was also indicated by a similar response of cylinder-head temperature for variations of fuel-air ratio at manifold pressures of 25 and 35 inches of mercury absolute. Both modified fuel-injection systems required less fuel-nozzle pressure than the standard system to obtain the desired fuel-air ratio for given air-flow condition.

Mulholland, Donald R.↗
NASA NTRS1940

A Method of Measuring Piston Temperatures

A method that makes use of thermocouples has been developed to measure the temperature of engine pistons operating at high speeds. The thermocouples installed on the moving piston are connected with a potentiometer outside the engine by means of pneumatically operated plungers, which make contact with the piston thermocouples for about 10 crankshaft degrees at the bottom of the piston stroke. The equipment is operated satisfactory at engine speeds of 2,400 r.p.m. and shows promise of successful operation at higher engine speeds. Measurements of piston temperatures in a liquid-cooled compression-ignition engine and in an air-cooled spark-ignition are presented.

Pinkel, Benjamin↗
NASA NTRS1935

Relation of Hydrogen and Methane to Carbon Monoxide in Exhaust Gases from Internal-Combustion Engines

The relation of hydrogen and methane to carbon monoxide in the exhaust gases from internal-combustion engines operating on standard-grade aviation gasoline, fighting-grade aviation gasoline, hydrogenated safety fuel, laboratory diesel fuel, and auto diesel fuel was determined by analysis of the exhaust gases. Two liquid-cooled single-cylinder spark-ignition, one 9-cylinder radial air-cooled spark-ignition, and two liquid-cooled single-cylinder compression-ignition engines were used.

Gerrish, Harold C↗