Search NASA⌕ Search

SEARCH · Search NASA

Results for “EQUATORIAL ORBIT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Solar rocket system concept analysis

The use of solar energy to heat propellant for application to Earth orbital/planetary propulsion systems is of interest because of its performance capabilities. The achievable specific impulse values are approximately double those delivered by a chemical rocket system, and the thrust is at least an order of magnitude greater than that produced by a mercury bombardment ion propulsion thruster. The primary advantage the solar heater thruster has over a mercury ion bombardment system is that its significantly higher thrust permits a marked reduction in mission trip time. The development of the space transportation system, offers the opportunity to utilize the full performance potential of the solar rocket. The requirements for transfer from low Earth orbit (LEO) to geosynchronous equatorial orbit (GEO) was examined as the return trip, GEO to LEO, both with and without payload. Payload weights considered ranged from 2000 to 100,000 pounds. The performance of the solar rocket was compared with that provided by LO2-LH2, N2O4-MMH, and mercury ion bombardment systems.

Boddy, J. A.↗
NASA NTRS1981

Low thrust chemical propulsion for orbit transfer of large space structures

For transporting Large Space Structures (LSS) from Low Earth Orbit (LEO) to Geosynchronous Equatorial Orbit (GEO), a variety of low thrust engine cycles have been evaluated for oxygen/hydrogen and oxygen/hydrocarbon propellants. The engine cycles included conventional propellant turbine drives (gas generator, expander, and staged-combustion cycles), turboalternator/electric motor pump drive, and fuel-cell/electric motor pump drive, as well as pressure-fed engines. The thrust chamber cooling limits and the engine cycle limits were established for a range of thrust levels. The candidate engine cycles were analyzed, screened, rated, and two engine cycle/configurations were selected for preliminary engine design. Preliminary engine designs for these two engines were formulated and engine design layouts prepared and parametric engine data generated.

Shoji, J. M.↗
NASA NTRS1985

Cryogenic upper stage test bed engine

A vehicle system with unique characteristics will be needed in connection with the extension of the Space Transportation System (STS) from Low Earth Orbit (LEO) to Geosynchronous Equatorial Orbit (GEO) and beyond. These characteristics are determined by NASA missions related to the deployment of large space structures, satellite servicing, and manned sorties to geosynchronous orbit. Advances in vehicle design and operation will be required along with significant advances in engine technologies. A versatile, well-instrumented test bed engine will be needed for the evaluation of the required technologies. Developments leading to the fabrication and assembly of the first high chamber pressure expander cycle test bed engine are discussed. The test bed engine, which is called Integrated Component Evaluator (ICE), is required for the development of an advanced, cryogenic, upperstage engine.

Pauckert, R.↗
NASA NTRS1992

Thermistor bolometer scanning radiometer - Applications and flight experience

Scanning radiometers aboard both high-altitude sun-synchronous polar orbit and low altitude equatorial orbit spacecraft have conducted measurements of the earth's long-wave radiation. Attention is presently given to the Earth Radiation Budget Satellite Experiment instruments, which are designed to measure earth radiance with an absolute radiometric error of less than 1 percent. The scanner instruments consists of three broadband radiometer channels employing thermistor bolometers as sensing elements; these radiometers repeatedly scan the earth from limb to limb every 4 sec, generating contiguous pixels on the earth's surface.

Kopia, Leonard P.↗
NASA NTRS2006

An Introduction to Rockets - or - Never Leave Geeks Unsupervised

An introduction to rockets along with a brief history Newton's third law is presented. The contents include: 1) What is a Rocket?; 2) A Brief History; 3) Newton's Third Law; 4) A Brief History; 5) Mission Requirements; 6) Some Orbital Measurements; 7) Self Eating Watermelon; 8) Orbital Inclinations; 9) 28.5 Equatorial Orbit; 10) 51.6 Orbit (ISS); 11) Polar Orbit; 12) Geostationary Orbit; 13) Liquid Rocket; 13) Liquids vs. Solids; 14) Liquids; 15) Systems Integration; 16) Integration (NFL!); 17) Guidance Systems; 18) Vectored Thrust; 19) Spin Stabilization; 20) Aerodynamic Stability (Fire Arrows); and 21) Center of Gravity & Center of Pressure.

Mellett, Kevin↗
NASA NTRS2015

Trajectory Design from GTO to Near-Equatorial Lunar Orbit for the Dark Ages Radio Explorer (DARE) Spacecraft

The trajectory design for the Dark Ages Radio Explorer (DARE) mission concept involves launching the DARE spacecraft into a geosynchronous transfer orbit (GTO) as a secondary payload. From GTO, the spacecraft then transfers to a lunar orbit that is stable (i.e., no station-keeping maneuvers are required with minimum perilune altitude always above 40 km) and allows for more than 1,000 cumulative hours for science measurements in the radio-quiet region located on the lunar farside.

Lunar orbit↗
NASA NTRS2014

Small Spacecraft System-Level Design and Optimization for Interplanetary Trajectories

The feasibility of an interplanetary mission for a CubeSat, a type of miniaturized spacecraft, that uses an emerging technology, the CubeSat Ambipolar Thruster (CAT) is investigated. CAT is a large delta-V propulsion system that uses a high-density plasma source that has been miniaturized for small spacecraft applications. An initial feasibility assessment that demonstrated escaping Low Earth Orbit (LEO) and achieving Earth-escape trajectories with a 3U CubeSat and this thruster technology was demonstrated in previous work. We examine a mission architecture with a trajectory that begins in Earth orbits such as LEO and Geostationary Earth Orbit (GEO) which escapes Earth orbit and travels to Mars, Jupiter, or Saturn. The goal was to minimize travel time to reach the destinations and considering trade-offs between spacecraft dry mass, fuel mass, and solar power array size. Sensitivities to spacecraft dry mass and available power are considered. CubeSats are extremely size, mass, and power constrained, and their subsystems are tightly coupled, limiting their performance potential. System-level modeling, simulation, and optimization approaches are necessary to find feasible and optimal operational solutions to ensure system-level interactions are modeled. Thus, propulsion, power/energy, attitude, and orbit transfer models are integrated to enable systems-level analysis and trades. The CAT technology broadens the possible missions achievable with small satellites. In particular, this technology enables more sophisticated maneuvers by small spacecraft such as polar orbit insertion from an equatorial orbit, LEO to GEO transfers, Earth-escape trajectories, and transfers to other interplanetary bodies. This work lays the groundwork for upcoming CubeSat launch opportunities and supports future development of interplanetary and constellation CubeSat and small satellite mission concepts.

Spangelo, Sara↗
NASA NTRS1974

A second-order theory of an artificial satellite under the influence of the oblateness of the earth

The general theory of the method of averaging is used to study the effect of the oblateness of the earth on the motion of an artificial satellite. The first-order harmonic J2 and the second-order harmonics J3 and J4 are included in the analysis. The first-order, periodic variations together with the second-order, averaged and secular variations are derived for all the six orbital elements. Alternative orbital elements and necessary relations are introduced to deal with circular orbits, orbits at critical inclination and equatorial orbits. Essential transformations and initialization procedures are also outlined.

Liu, J. J. F.↗
NASA NTRS1981

Primary propulsion/large space system interaction study

An interaction study was conducted between propulsion systems and large space structures to determine the effect of low thrust primary propulsion system characteristics on the mass, area, and orbit transfer characteristics of large space systems (LSS). The LSS which were considered would be deployed from the space shuttle orbiter bay in low Earth orbit, then transferred to geosynchronous equatorial orbit by their own propulsion systems. The types of structures studied were the expandable box truss, hoop and column, and wrap radial rib each with various surface mesh densities. The impact of the acceleration forces on system sizing was determined and the effects of single point, multipoint, and transient thrust applications were examined. Orbit transfer strategies were analyzed to determine the required velocity increment, burn time, trip time, and payload capability over a range of final acceleration levels. Variables considered were number of perigee burns, delivered specific impulse, and constant thrust and constant acceleration modes of propulsion. Propulsion stages were sized for four propellant combinations; oxygen/hydrogen, oxygen/methane, oxygen/kerosene, and nitrogen tetroxide/monomethylhydrazine, for pump fed and pressure fed engine systems. Two types of tankage configurations were evaluated, minimum length to maximize available payload volume and maximum performance to maximize available payload mass.

Coyner, J. V.↗
NASA NTRS1991

NASA's advanced space transportation system launch vehicles

Some insight is provided into the advanced transportation planning and systems that will evolve to support long term mission requirements. The general requirements include: launch and lift capacity to low earth orbit (LEO); space based transfer systems for orbital operations between LEO and geosynchronous equatorial orbit (GEO), the Moon, and Mars; and Transfer vehicle systems for long duration deep space probes. These mission requirements are incorporated in the NASA Civil Needs Data Base. To accomplish these mission goals, adequate lift capacity to LEO must be available: to support science and application missions; to provide for construction of the Space Station Freedom; and to support resupply of personnel and supplies for its operations. Growth in lift capacity must be time phased to support an expanding mission model that includes Freedom Station, the Mission to Planet Earth, and an expanded robotic planetary program. The near term increase in cargo lift capacity associated with development of the Shuttle-C is addressed. The joint DOD/NASA Advanced Launch System studies are focused on a longer term new cargo capability that will significantly reduce costs of placing payloads in space.

Branscome, Darrell R.↗
NASA NTRSDate not supplied

Flight and Direct to Earth/Space Relay Communication System Architecture for GSFC CubeSat Missions

The CubeSat platform is finding increasing use in space science applications due to its low cost and comparative ease of launch. It is becoming a key scientific discovery tool in low Earth orbit (LEO) and beyond, including geosynchronous equatorial orbit (GEO), the Lagrange Points, Lunar missions, and more. The increasing complexity of these missions and their scientific goals must be supported by equal advancements in communications technology. Higher data rates and greater reliability are required every year. However, the reduced Size, Weight, and Power (SWaP) constraints of CubeSat platforms introduce unique challenges in the area of satellite communications. There is currently a lack of communication equipment tailored specifically to the CubeSat platform. This lack of standardized, tested equipment extends development time and reduces mission confidence. Furthermore, missions utilizing the CubeSat platform are often subject to more difficult design constraints. Antenna placement, size, and pointing are often subordinate to the requirements of the payload instruments and mission goals. Traditional link margin estimation techniques are insufficient in these cases, as they emphasize worst case scenarios. In reality the actual link parameters may vary widely even during a single pass. This presents new challenges in predicting communications performance and scheduling ground station contacts, but also new opportunities for improving efficiency. This paper presents the integration, testing, and validation process for a new software defined radio (SDR) designed for the CubeSat platform in conjunction with Vulcan Wireless, Inc. The SDR is planned for use on 5 upcoming CubeSat missions at NASAs Goddard Space Flight Center (GSFC) including a Geosynchronous Transfer Orbit (GTO) mission and it may also serve as a standard and well-tested option for future missions by enabling a standardized, rapid and low cost CubeSat communication system network integration process. Detailed simulations have been developed to estimate the communication performance of these missions, taking the unique antenna placements and attitude behavior of each satellite into account. These simulations allow a much more accurate analysis of the expected link margin, which varies considerably during each pass for the NASA Space Relay (SR) and Direct to Earth (DTE) network. The modelling procedures are outlined, and the results are used to predict communications performance of the missions.

Space Networks↗
NASA NTRS1962

VELOCITY REQUIREMENTS FOR THE CORRECTION OF A 24-HOUR ORBIT

An investigation of the amount of velocity or energy required to correct an orbit to a near-perfect, circular, equatorial orbit with a period of one sidereal day. The required velocity is shown to be a function of the satellite position and velocity errors at the time correction is to be performed, as well as certain parameters inherent in the "guidance law." The results in their final form permit computation of the corrective velocity as a function of initial injection cut-off errors and errors arising from perturbative accelerations.

ORBIT↗
NASA NTRS1974

Wide area coverage radar imaging satellite for earth applications

A preliminary study was made of a radar imaging satellite for earth applications. A side-looking synthetic-aperture radar was considered and the feasibility of obtaining a wide area coverage to reduce the time required to image a given area was investigated. Two basic approaches were examined; low altitude sun-synchronous orbits using a multibeam/multifrequency radar system and equatorial orbits up to near-synchronous altitude using a single beam system. Surveillance and mapping of ice on the Great Lakes was used as a typical application to focus the study effort.

Stevens, G. H.↗
NASA NTRS2006

Recent Highlights in Ring Structure, Dynamics, and Composition

While the Cassini orbiter has been in a near-equatorial orbit for most of the time since the last DPS meeting, the science teams have turned to preliminary analysis of many aspects of data taken over the first year of the mission. New understanding has been gained of several different aspects of ring structure and dynamics - especially the small-scale ring vertical structure related to marginal gravitational instabilities, and the diverse roles played by small moonlets sprinkled around and within the rings. In addition, a closer look is being taken at how ring composition varies locally and regionally and how this variation compares with models of ring compositional evolution. Cassini will re-emerge from the equator plane in late July, and new ring observations will again be available. In this talk we will review progress over the last year, highlight key outstanding issues and problems, and provide a context for the new observations reported at this meeting.

Cuzzi, Jeffrey N.↗
NASA NTRS1976

Substorm observations of magnetic perturbations and ULF waves at synchronous orbit by ATS-1 and ATS-6

In the empirical study of the geomagnetic cavity, the synchronous equatorial orbit has been shown to be a most advantageous site for scientific measurements. Satellites in this orbit are fixed in the earth's main magnetic field so that the records are not dominated by changes due to satellite motion through this field. Also, the satellites traverse the same geometric region of space daily, thus facilitating statistical studies of magnetospheric phenomena. Thirdly, the magnetic field lines leaving the earth's surface near the auroral zone cross the equatorial plane close to this orbit, thus subjecting the region to a number of such phenomena. Previous observations at synchronous orbit with the UCLA fluxgate magnetometers on ATS-1 and ATS-6 have revealed a variety of substorm-associated field variations. These effects may be divided tentatively into two classes, those resulting from instabilities (ULF waves) and those produced by changes in macroscopic current systems. The data and their interpretations will be reviewed in order to illustrate the potential importance of observations in the synchronous orbit during the International Magnetospheric Study.

Coleman, P. J., Jr.↗
NASA NTRS1999

In-Space Transportation for GEO Space Solar Power Satellites

This report summarizes results of study tasks to evaluate design options for in-space transportation of geostationary Space Solar Power Satellites. Referring to the end-to-end architecture studies performed in 1988, this current activity focuses on transportation of Sun Tower satellite segments from an initial low Earth orbit altitude to a final position in geostationary orbit (GEO; i.e., 35,786 km altitude, circular, equatorial orbit). This report encompasses study activity for In-Space Transportation of GEO Space Solar Power (SSP) Satellites including: 1) assessment of requirements, 2) design of system concepts, 3) comparison of alternative system options, and 4) assessment of potential derivatives.

Martin, James A.↗
NASA NTRS1978

Space Spider - A concept for fabrication of large structures

The Space Spider concept for the automated fabrication of large space structures involves a specialized machine which roll-forms thin gauge material such as aluminum and develops continuous spiral structures with radial struts to sizes of 600-1,000 feet in diameter by 15 feet deep. This concept allows the machine and raw material to be integrated using the Orbiter capabilities, then boosting the rigid system to geosynchronous equatorial orbit (GEO) without high sensitivity to acceleration forces. As a teleoperator controlled device having repetitive operations, the fabrication process can be monitored and verified from a ground-based station without astronaut involvement in GEO. The resultant structure will be useful as an intermediate size platform or as a structural element to be used with other elements such as the space-fabricated beams or composite nested tubes.

Britton, W. R.↗