SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Female die facilitates the removal of a sheet metal structure from a die used for explosive forming of the metal. The female die consists of a smooth conical frustum made of fiber glass with a cured epoxy-resin surface on which a molded grid pattern made of a polyurethane resin is overlaid.
Work is reported for fabricating and testing the fiberglass overwrapped titanium pressure vessel for cryogenic service. Difficulties encountered in the tank liner fabrication phase involved explosive forming, vacuum annealing, chemical milling and electron beam welding. While each of these processes and the nondestructive test methods employed are normally considered to be individually reliable, the combination of poor material together with fabrication and development reversals prevented the full achievement of the desired end results. Eight tanks plus a prototype and tool proofing article were produced. Six of the vessels failed during the hydrostatic sizing operation. One of the remaining tanks was hydrostatically pressurized to burst and the other was pressurized repeatedly at 75 F from 100 psi to the operating pressure until failure occurred. As a result, it is not possible to draw firm conclusions as to the true value of the design concept due to the problems encountered in the program.
Noble gas contents and shock effects have been studied in 21 Odessa irons from known geographic locations. Cosmogenic He-3, Ne-21, Ar-38 contents and He-3/Ne-21 ratios vary by factors of 62, 91, 68, and 1.55, respectively, while Ne-22/Ne-21 ratios are virtually constant at 1.07. The samples fall into two groups differing by a factor of 4.1 in exposure age, 1000 in source mass, or some combination of these. Three samples show significant shock effects, two of them to above 130 kbar, probably arising during terrestrial impact from the crater-forming explosion. As in Canyon Diablo plains specimens, noble gas contents do not correlate with siting or shock.
Simple gage, used with template, can help inspectors determine whether three-dimensional curved surface has correct contour. Gage was developed as aid in explosive forming of Space Shuttle emergency-escape hatch. For even greater accuracy, wedge can be made of metal and calibrated by indexing machine.
Theoretical models proposed to explain the origin of the millisecond pulsar (MP) PSR 1937+214 are reviewed, examining their ability to explain its low surface dipole magnetic field (B), its low birth temperature (less than 10 to the 8th K), the absence of a companion or remnant, and its low velocity perpendicular to the Galactic plane. The models discussed are a single isolated explosion forming a rapidly spinning neutron star, spin-up of a dead pulsar by accretion from a companion, collapse of an accreting spinning white dwarf, and fusion of a tight binary composed of two old neutron stars. Although all of the models have difficulties in explaining one or more of the MP characteristics, the second model is found to be most probable in the light of present knowledge. The lack of a companion is explained by its tidal disruption after it had fed the accreting pre-pulsar for 1 Gyr or more and its mass had decreased to about 0.01 solar mass. Neutron stars accreting in this way have been observed in Galactic-bulge X-ray sources.
Explosive forming, wax filling, and any one of welding, diffusion bonding, or brazing used in method of manufacturing large, complicated shell-and-liner vessels or structures. Method conceived for manufacture of film-cooled rocket nozzles but applicable to joining large coaxial shells and liners in general.
Gasoline, the fuel now used, is an extremely volatile and inflammable liquid capable of forming explosive mixtures, the cause of many catastrophes in aviation. It is therefore of special interest to investigate the possibility of using fuels which, while being less volatile than gasoline, would nevertheless enable this engine to function satisfactorily.
This report not only presents matters of practical importance in the classification of engine fuels, for which other means have proved inadequate, but also makes a few suggestions. It confirms the results of Withrow and Boyd which localize the explosive wave in the last portions of the mixture burned. This being the case, it may be assumed that the greater the normal combustion, the less the energy developed in the explosive form. In order to combat the detonation, it is therefore necessary to try to render the normal combustion swift and complete, as produced in carbureted mixtures containing benzene (benzol), in which the flame propagation, beginning at the spark, yields a progressive and pronounced darkening on the photographic film.
Hydrogen is a versatile and clean energy carrier that can be produced from various renewable sources such as wind, solar, and hydropower. Hydrogen has the potential to play a crucial role in decarbonizing industrial processes that are currently reliant on fossil fuels and provide long-duration and/or seasonal energy storage to enable electricity decarbonization. Hydrogen can also be used as a fuel for fuel cell vehicles, providing a zero-emission alternative to traditional internal combustion engines. DOE launched the Hydrogen Energy Earthshot (Hydrogen Shot) in June 2021 to reduce the cost of clean hydrogen by 80% to $1 per 1 kilogram in 1 decade ("1 1 1"). While promising, Hydrogen is highly-flammable, and in the presence of oxygen, it can form explosive mixtures. . Therefore, understanding leak scenarios is essential to evaluate and mitigate the safety risks associated with potential hydrogen leaks. An increased understanding of leak behavior, and having tools to model leaks, can help assess how hydrogen would disperse in different environments, influencing emergency response plans and safety measures, and identify potential issues with materials and design systems that can withstand the challenges posed by hydrogen. Recently, researchers have attempted to study hydrogen leaks for development of risk management strategies. However, the focus has been on closed or semi-closed spaces like storage rooms, vehicles, garages, and fueling stations - all promising locations for future hydrogen infrastructure. In this presentation, the modeling environment extends the span of research further by modeling hydrogen leak in an outdoor, open space. We will present the key challenges with modeling hydrogen leaks in an uncontrollable environment, how they were handled, and how modeling results informed sensor selection and placement. A Hydrogen research facility at the National Renewable Energy Laboratory (NREL) was used as a case study to model hydrogen leaks. In the future, Hydrogen wide area detection methodologies will be developed and tested at this site to monitor for unintended and operational hydrogen releases. The data generated from modeling will be used to develop a predictive model to detect hydrogen leak location based on concentration measured by sensors in this open space. Furthermore, the facility was also chosen because controlled hydrogen releases can be performed. A computational fluid dynamics (CFD) based modeling approach was taken to model hydrogen leak. The full-scale hydrogen facility was modeled with a large ambient domain. The electrolyzer at the facility can produce a controlled release rate of 27 kg-H2/hr. Site-specific atmospheric and weather condition data such as wind direction, wind speed at various altitudes, and temperature were used as inputs to the model. To capture the variability of weather conditions, a subset of the weather conditions experienced during daytime hours without precipitation over the course of three months was generated; using established data clustering techniques, a total of 100 condition sets were chosen. The results show statistical distributions and ranges of hydrogen concentrations at locations throughout the domain. These distributions are compared to experimental data from a constant mass flow, controlled hydrogen release at the facility. The stochastic wind conditions of the release make direct validation difficult, therefore, statistical comparison approaches were used. Wind conditions are found to significantly impact the release behavior, including direction and concentration. Sensor selection and placement is proposed for the facility and is now based on release behavior predicted for the facility given its weather patterns; this is much more informed than without the modeling results. The methodology and analysis procedure can be translated to other facilities using modified geometries and site-specific weather conditions. Hydrogen holds great promise as a renewable energy fuel, but ensuring safety in its production, storage, and use is paramount. Studying potential leak scenarios in an open space will help develop sensors to detect hydrogen on a large spectrum of concentration and eventually build a smart distributed monitoring system.
Primacord which is woven through fish netting in a grid pattern is used for explosive forming of large sheet metal parts. The explosive force generated by the primacord detonation is uniformly distributed over the entire surface of the sheet metal workpiece.
The evolution of a giant H II region, which cools after an initial ionization, is discussed. The discussion is applied to the Vela X and Tycho supernovae. Other giant H II regions might not be as easily detectable as the Vela X region. The Tycho region may be just detectable in the O(II) or O(III) optical lines or as a hole in the 21-cm emission line profiles, as is suggested in the data. These giant H II regions last appreciably longer than the continuum radio sources within them.
Explore the source record for details and available documents.
Abstract We have simulated the collapse and evolution of the core of a solar-metallicity 40 M ⊙ star and find that it explodes vigorously by the neutrino mechanism, despite its very high “compactness.” Within ∼1.5 s of explosion, a black hole forms. The explosion is very asymmetrical and has a total explosion energy of ∼1.6 × 10 51 erg. At black hole formation, its baryon mass is ∼2.434 M ⊙ and gravitational mass is 2.286 M ⊙ . Seven seconds after black hole formation, an additional ∼0.2 M ⊙ is accreted, leaving a black hole baryon mass of ∼2.63 M ⊙ . A disk forms around the proto−neutron star, from which a pair of neutrino-driven jets emanates. These jets accelerate some of the matter up to speeds of ∼45,000 km s −1 and contain matter with entropies of ∼50. The large spatial asymmetry in the explosion results in a residual black hole recoil speed of ∼1000 km s −1 . This novel black hole formation channel now joins the other black hole formation channel between ∼12 and ∼15 M ⊙ discovered previously and implies that the black hole/neutron star birth ratio for solar-metallicity stars could be ∼20%. However, one channel leaves black holes in perhaps the ∼5–15 M ⊙ range with low kick speeds, while the other leaves black holes in perhaps the ∼2.5–3.0 M ⊙ mass range with high kick speeds. However, even ∼8.8 s after core bounce the newly formed black hole is still accreting at a rate of ∼2 × 10 −2 M ⊙ s −1 , and whether the black hole eventually achieves a significantly larger mass over time is yet to be determined.
When subjected to a shock of insufficient strength to trigger prompt reaction, heterogenous condensed phase explosives can form regions where significant amounts of the explosive remain unreacted for times much greater than the reaction time of the detonating explosive. This phenomena is observed for the explosive PBX 9502 (95 wt% TATB) both for planar and oblique input shocks. Here, we build on previous results by performing cylinder expansion (CYLEX) tests where the explosive charge is comprised of a faster core of PBX 9501 (95 wt% HMX) inside a slower annulus of PBX 9502. The detonation in the faster PBX 9501 drives an oblique shock into the adjacent PBX 9502, and an annular transverse initiating layer (IL) results. In the test geometry, the IL travels steadily down the length of the test after a short run distance. At radial positions beyond the IL, an annular region of detonating PBX 9502 is observed. Using standard CYLEX test diagnostics, we infer the total energy release of this experiment. By making the assumptions that (1) the combined energy release is comprised of contributions from detonating PBX 9501, detonating PBX 9502, and the IL in the PBX 9502 and (2) mass-specific energy release for the detonating explosives is approximately the same as typically observed for each explosive, the IL energy release and reaction efficiency can be computed. Results are compared to prior results for a similar geometry, and indicate that while shock deadened PBX 9502 does not detonate promptly, it does eventually release a significant portion of its chemical potential energy over longer timescales on the order of 10 µs.
Transient collimated plasma ejections (jets) occur frequently throughout the solar corona, in active regions, quiet Sun, and coronal holes. Although magnetic reconnection is generally agreed to be the mechanism of energy release in jets, the factors that dictate the location and rate of reconnection remain unclear. Our previous studies demonstrated that the magnetic breakout model explains the triggering and evolution of most jets over a wide range of scales, through detailed comparisons between our numerical simulations and high-resolution observations. An alternative explanation, the resistive-kink model, invokes breakout reconnection without forming and explosively expelling a flux rope. Here we report direct observations of breakout reconnection and plasmoid formation during two jets in the fan-spine topology of an embedded bipole. For the first time, we observed the formation and evolution of multiple small plasmoids with bidirectional flows associated with fast reconnection in 3D breakout current sheets (BCSs) in the solar corona. The first narrow jet was launched by reconnection at the BCS originating at the deformed 3D null, without significant flare reconnection or a filament eruption. In contrast, the second jet and release of cool filament plasma were triggered by explosive breakout reconnection when the leading edge of the rising flux rope formed by flare reconnection beneath the filament encountered the preexisting BCS. These observations solidly support both reconnection-driven jet models: the resistive kink for the first jet, and the breakout model for the second explosive jet with a filament eruption.
The quality of toxic gases formed during explosive work in underground shafts depends upon the type of explosives and the conditions of explosion. Several types of explosives and rocks were examined. All remaining conditions were maintained the same (sandy-argillaceous stemming, electrical method of explosions, diameter of blast holes, and the direct triggering of charges).
A technique and apparatus for optically detonating insensitive high explosives, is disclosed. An explosive device is formed by containing high explosive material in a house having a transparent window. A thin metallic film is provided on the interior surface of the window and maintained in contact with the high explosive. A laser pulse provided by a Q-switched laser is focussed on the window to vaporize the metallic film and thereby create a shock wave which detonates the high explosive. Explosive devices may be concurrently or sequentially detonated by employing a fiber optic bundle to transmit the laser pulse to each of the several individual explosive devices.
The present paper deals with the conditions of explosion or nuclear cratering required to simulate impact crater formation. Some planetary problems associated with three different aspects of crater formation are discussed, and solutions based on high-explosion data are proposed. Structures of impact craters and some selected explosion craters formed in layered media are examined and are related to the structure of lunar basins. The mode of ejection of material from impact craters is identified using explosion analogs. The ejection mode is shown to have important implications for the origin of material in crater and basin deposits. Equally important are the populations of secondary craters on lunar and planetary surfaces.