Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electron cyclotron heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Isotope effects on transport in LHD

Abstract Isotope effects are one of the most important issues for predicting future reactor operations. Large helical device (LHD) is the presently working largest stellarator/helical device using super conducting helical coils. In LHD, deuterium experiments started in 2017. Extensive studies regarding isotope effects on transport have been carried out. In this paper, the results of isotope effect studies in LHD are reported. The systematic studies were performed adjusting operational parameters and nondimensional parameters. In L mode like normal confinement plasma, where internal and edge transport barriers are not formed, the scaling of global energy confinement time ( τ E ) with operational parameters shows positive mass dependence ( M 0.27 ; where M is effective ion mass) in electron cyclotron heating plasma and no mass dependence ( M 0.0 ) in neutral beam injection heating plasma. The non-negative ion mass dependence is anti-gyro-Bohm scaling. The role of the turbulence in isotope effects was also found by turbulence measurements and gyrokinetic simulation. Better accessibility to electron and ion internal transport barrier (ITB) plasma is found in deuterium (D) plasma than in hydrogen (H). Gyro kinetic non-linear simulation shows reduced ion heat flux due to the larger generation of zonal flow in deuterium plasma. Peaked carbon density profile plays a prominent role in reducing ion energy transport in ITB plasma. This is evident only in plasma with deuterium ions. New findings on the mixing and non-mixing states of D and H particle transports are reported. In the mixing state, ion particle diffusivities are higher than electron particle diffusivities and D and H ion density profiles are almost identical. In the non-mixing state, ion particle diffusivity is much lower than electron diffusivity. Deuterium and hydrogen ion profiles are clearly different. Different turbulence structures were found in the mixing and non-mixing states suggesting different turbulence modes play a role.

Physics↗
DOE OSTI2023

Energetic electron transport in magnetic fields with island chains and stochastic regions

This paper investigates energetic electron transport in magnetized toroidal plasmas with magnetic fields characterized by island chains and regions of stochastic field lines produced by coil perturbations. We report on experiments performed in the DIII-D tokamak, which utilize electron cyclotron heating and current drive pulses to ‘tag’ electron populations within different locations across the discharge. The cross-field transport of these populations is then inferred from electron cyclotron emission measurements and gamma emission signals from scintillator detectors. Two types of energetic particles are distinguished and discussed: non-relativistic suprathermal electrons and relativistic runaway electrons. The magnetic field topology in each discharge is reconstructed with field-line tracing codes, which are also used to determine the location and scale of magnetic islands and stochastic regions. Comparison of simulations and experiments suggests that suprathermal transport is suppressed when the tagging is performed at a smaller radial location than the location of the $q = 1$ island chain and enhanced otherwise. Here q is the safety factor. We further demonstrate that increasing the width of the stochastic region within the edge plasma yields enhancement of the suprathermal electron transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Nonlinear burn control in ITER using adaptive allocation of actuators with uncertain dynamics

Abstract ITER will be the first tokamak to sustain a fusion-producing, or burning, plasma. If the plasma temperature were to inadvertently rise in this burning regime, the positive correlation between temperature and the fusion reaction rate would establish a destabilizing positive feedback loop. Careful regulation of the plasma’s temperature and density, or burn control, is required to prevent these potentially reactor-damaging thermal excursions, neutralize disturbances and improve performance. In this work, a Lyapunov-based burn controller is designed using a full zero-dimensional nonlinear model. An adaptive estimator manages destabilizing uncertainties in the plasma confinement properties and the particle recycling conditions (caused by plasma–wall interactions). The controller regulates the plasma density with requests for deuterium and tritium particle injections. In ITER-like plasmas, the fusion-born alpha particles will primarily heat the plasma electrons, resulting in different electron and ion temperatures in the core. By considering separate response models for the electron and ion energies, the proposed controller can independently regulate the electron and ion temperatures by requesting that different amounts of auxiliary power be delivered to the electrons and ions. These two commands for a specific control effort (electron and ion heating) are sent to an actuator allocation module that optimally maps them to the heating actuators available to ITER: an electron cyclotron heating system (20 MW), an ion cyclotron heating system (20 MW), and two neutral beam injectors (16.5 MW each). Two different actuator allocators are presented in this work. The first actuator allocator finds the optimal mapping by solving a convex quadratic program that includes actuator saturation and rate limits. It is nonadaptive and assumes that the mapping between the commanded control efforts and the allocated actuators (i.e. the effector model) contains no uncertainties. The second actuator allocation module has an adaptive estimator to handle uncertainties in the effector model. This uncertainty includes actuator efficiencies, the fractions of neutral beam heating that are deposited into the plasma electrons and ions, and the tritium concentration of the fueling pellets. Furthermore, the adaptive allocator considers actuator dynamics (actuation lag) that contain uncertainty. This adaptive allocation algorithm is more computationally efficient than the aforementioned nonadaptive allocator because it is computed using dynamic update laws so that finding the solution to a static optimization problem is not required at every time step. A simulation study assesses the performance of the proposed adaptive burn controller augmented with each of the actuator allocation modules.

Physics↗
DOE OSTI2023

Density wavenumber spectrum measurements, synthetic diagnostic development, and tests of quasilinear turbulence modeling in the core of electron-heated DIII-D H-mode plasmas

Abstract Measurements of the turbulent density wavenumber spectrum, δ n ˆ e ( k ⊥ ) , using the Doppler Back-Scattering (DBS) diagnostic are reported from DIII-D H-mode plasmas with electron cyclotron heating as the only auxiliary heating method. These electron-heated plasmas have low collisionality, ν e ∗ < 1 , T e / T i > 1 , and zero injected torque—a regime expected to be relevant for future fusion devices. We probe density fluctuations in the core ( ρ ≈ 0.7) over a broad wavenumber range, 0.5 ⩽ k ⊥ ⩽ 16 cm −1 ( 0.1 ⩽ k ⊥ ρ s ⩽ 5 ), to characterize plasma instabilities and compare with theoretical predictions. We present a novel synthetic DBS diagnostic to relate the back-scattered power spectrum, P s ( k ⊥ ) —which is directly measured by DBS—to the underlying electron density fluctuation spectrum, δ n ˆ e ( k ⊥ ) . The synthetic DBS P s ( k ⊥ ) spectrum is calculated by combining the SCOTTY beam-tracing code with a model δ n ˆ e ( k ⊥ ) predicted either analytically or numerically. In this work we use the quasi-linear code Trapped Gyro-Landau Fluid (TGLF) to approximate the δ n ˆ e ( k ⊥ ) spectrum. We find that TGLF, using the experimental profiles, is capable of closely reproducing the DBS measurements. Both the DBS measurements and the TGLF-DBS synthetic diagnostic show a wavenumber spectrum with variable decay. The measurements show weak decay ( k −0.6 ) for k < 3.5 cm −1 , with k −2.6 at intermediate- k ( 3.5 ⩽ k ⩽ 8.5 cm −1 ), and rapid decay ( k −9.4 ) for k > 8.5 cm −1 . Scans of physics parameters using TGLF suggest that the normalized ∇ T e scale-length, R / L T e , is an important factor for distinguishing microturbulence regimes in these plasmas. A combination of DBS observations and TGLF simulations indicate that fluctuations remain peaked at ITG-scales (low k ) while R / L T e -driven TEM/ETG-type modes (intermediate/high k ) are marginally sub-dominant.

synthetic diagnostics↗
DOE OSTI2020

Heat Flux Analysis From IR Imaging on Proto-MPEX

The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) is a linear device used to develop the source and heating concept for MPEX, an experiment to study plasma–material interactions for future fusion reactors. This paper highlights recent analysis and results on Proto-MPEX using an infrared (IR) camera, a key tool for imaging heat fluxes measured at the material target. The target heat fluxes are crucial to understanding the source and heating concepts. The recent analysis includes the application of homography and 3-D finite-element methods to provide between-shot measurements of the 2-D target heat flux profile. The IR camera inferred heat flux is shown to correlate with Langmuir probe inferred heat fluxes for a range of parameters in helicon only and helicon + electron cyclotron heated discharges. Results show both desirable central and undesirable edge heat flux for helicon source and electron heating on the target. These heat flux measurements are shown to be important for better understanding of the source and heating physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Analysis of the ECH effect on EPM/AE stability in Heliotron J plasma using a Landau closure model

The aim of the present study is to analyze the effect of the electron cyclotron heating (ECH) on the linear stability of Alfvén eigenmodes (AEs) and energetic particle modes (EPMs) triggered by energetic ions in Heliotron J plasma. The analysis is performed using the FAR3d code that solves a reduced MHD model to describe the thermal plasma coupled with a gyrofluid model for the energetic particle (EP) species. The simulations reproduce the AE/EPM stability trends observed in the experiments as the electron temperature (T e ) increases, modifying the thermal plasma β, EP β and EP slowing-down time. Particularly, the $n/m = 1/2$ EPM and $2/4$ Global AE are stabilized in the low-bumpiness (LB) configuration due to an enhancement of the continuum, finite Larmor radius and e-i Landau damping effects as the thermal β increases. On the other hand, a larger ECH injection power cannot stabilize the AE/EPM in medium-bumpiness and high-bumpiness (HB) configurations because the damping effects are weaker compared to the LB case, unable to balance the further destabilization induced by an enhanced EP resonance as the EP slowing-down time and EP β increases with T e .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

TorbeamNN: machine learning-based steering of ECH mirrors on KSTAR

We have developed TorbeamNN: a machine learning surrogate model for the TORBEAM ray tracing code to predict electron cyclotron heating (ECH) and current drive locations in tokamak plasmas. TorbeamNN provides more than a 100 times speed-up compared to the highly optimized and simplified real-time implementation of TORBEAM without any reduction in accuracy compared to the offline, full fidelity TORBEAM code. The model was trained using KSTAR ECH mirror geometries and works for both O-mode and X-mode absorption. The TorbeamNN predictions have been validated both offline and real-time in experiment. TorbeamNN has been utilized to track an ECH absorption vertical position target in dynamic KSTAR plasmas as well as under varying toroidal mirror angles and with a minimal average tracking error of 0.5 cm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Final Design of Vacuum Pumping Systems for the Material Plasma Exposure eXperiment

The Material Plasma Exposure eXperiment (MPEX) vacuum pumping system is responsible for creating prototypic conditions in the plasma material interaction chamber that mimic those in a fusion reactor divertor region. Additionally, the vacuum system needs to minimize the pressure in the plasma heating region to improve the coupling of the electron cyclotron heating and ion cyclotron heating to the plasma, minimizing waste heat exhausted to high heat flux components. Here, the final design of the system has been sized to comply with the vacuum pump operating environment and to reduce the number of unique pumps required while meeting performance requirements. Bounding cases with and without the plasma present have been developed in the pumping analysis, and an initial calculation has been performed based on the plasma pumping identified in Proto-MPEX operation though this result will remain unverified until MPEX operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Long-pulse high-performance H-mode plasmas achieved on EAST

A record duration of a 310 s H-mode plasma (H 98y2 ~ 1.3, n e /n GW ~ 0.7, f BS > 50%) has been recently achieved on experimental advanced superconducting tokamak (EAST) with metal walls, exploiting the device's improved long-pulse capabilities. The experiment demonstrates good control of tungsten concentration, core/edge MHD stability, and particle and heat exhaust with an ITER-like tungsten divertor and zero injected torque, establishing a milestone on the path to steady-state long-pulse high-performance scenarios in support of ITER and CFETR. Important synergistic effects are leveraged toward this result, which relies purely on radio frequency (RF) powers for heating and current drive (H&CD). On-axis electron cyclotron heating enhances the H&CD efficiency from lower hybrid wave injection, increasing confinement quality and enabling fully non-inductive operation at high density (n e /n GW ~ 70%) and high poloidal beta (β P ~ 2.5). A small-amplitude grassy edge localized mode regime facilitates the RF power coupling to the H-mode edge and reduces divertor sputtering/erosion. The high energy confinement quality (H 98y2 ~ 1.3) is achieved with the experimental and simulated results pointing to the strong effect of Shafranov shift on turbulence. Transport analysis suggests that trapped electron modes dominate in the core region during the record discharge. The detailed physics processes (RF synergy, core-edge integration, confinement properties, etc.) of the steady-state operation will be illustrated in the content. In the future, EAST will aim at accessing more relevant dimensionless parameters to develop long-pulse high-performance plasma toward ITER and CFETR steady-state advanced operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Evolution of ELMs, pedestal profiles and fluctuations in the inter-ELM period in NBI and ECH dominated discharges in DIII-D

In DIII-D, it has been observed that ELM frequency decreases by 40% and ELM spacing becomes more regular in time when heating is changed from pure neutral beam injection (NBI) to predominantly electron cyclotron heating (ECH) in ITER Similar Shape plasmas. In comparison with pure the NBI discharges, pedestal fluctuations in magnetics and density increase in the ECH dominated discharges. Recovery of the pedestal profiles like electron density (ne), temperature (Te) and pressure (pe) shows marked differences for these two heating schemes. Average profiles in the last 30% of the ELM cycle shows higher Te, lower ne, and similar pe at the pedestal top for the ECH discharge when compared to the NBI discharge. Here, the gradient of Te (∇Te) is also steeper at the pedestal in the ECH discharge. Magnetic fluctuations show 3 distinct modes in 13~116 kHz in the ECH discharges only. ne fluctuations show two modes evolving in the inter-ELM period of the ECH discharge, a low frequency (400 kHz) quasi-coherent mode (LFQC) and high frequency (~2 MHz) broadband (HFB) fluctuations. Evolution of these modes has marked correspondence with the inter-ELM ∇Te recovery. A sharp decrease in the Dα baseline is observed whenever the LFQC weakens and the HFB grows, prior to each large ELM. Transport coefficients obtained from TRANSP shows that MTM and/or TEM are plausible candidates for the observed fluctuations. Linear gyrofluid simulation (TGLF) corroborates this characterization. TGLF shows that the linear growth rate of the most dominant mode peaks at ion-scale (kθρs ~ 0.4) at the pedestal steep gradient and the frequency is in the electron diamagnetic direction. It is proposed that increased fluctuations in the ECH dominated case, due to increased ∇Te, caused an increase in fluctuation-driven transport in the pedestal and slowed the pedestal recovery between ELMs, leading to a reduction in the ELM frequency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Observation and characterisation of trapped electron modes in Wendelstein 7-X

In the past, quasi coherent (QC) modes were reported for nearly all tokamaks. The general definition describes modes as QC when the magnitude squared coherence is in the range of 0.3 to 0.6. QC modes are observed in the plasma core as well as in the plasma edge and can have quite different physical origins. The one in the core are observed in plasmas with low collisionality, where the electron temperature exceeds the ion temperature in the plasma core. This is the case for electron cyclotron heating in general. The origin of these modes are electrons trapped within a magnetic mirror, as reported in the past from various fusion devices. The so-called trapped-electron modes (TEMs) belong to drift wave instabilities and can be destabilized by electron-temperature gradients in the plasma core. From the diagnostic point of view, QC modes appear as fluctuations in electron density and temperature. Therefore, the microwave reflectometer is very well suited to monitor these modes. This paper describes experiments, conducted at the Wendelstein 7-X stellarator (W7-X), which aim at detecting QC modes at low wave numbers. A poloidal correlation reflectometer installed at W7-X, is able to measure low wave numbers ($k_\perp\unicode{x2A7D}{3.5}\,\textrm{cm}^{-1}$). For medium line-averaged densities ($\int n_\textrm{e}\unicode{x2A7D}{6 \times10^{19}}\,\textrm{m}^{-2}$) the plasma core is accessible for this diagnostic. For different magnetic configurations and plasma parameters, broad QC structures are observed in the coherence spectra. From the analysis of the rotation and the poloidal structure, these QC modes show the properties of electron-temperature-gradient driven TEMs. A linear relation between the mode velocity and the rotation frequency is found. The relation is uniform and confirms the nature of QC-mode observation as TEM in tokamaks, too.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Investigation of core transport changes in DIII-D discharges with off-axis T e profile peaks

Abstract DIII-D discharges that transition to H-mode solely with off-axis electron cyclotron heating (ECH) often exhibit strong off-axis peaking of electron temperature profiles at the heating location. Electron heat transport properties near these off-axis temperature peaks have been studied using modulated ECH. The Fourier analyzed electron temperature data have been used to infer electron thermal diffusivity. Comparisons with numerical solutions of the time-dependent electron thermal equation find that the data are consistent with a narrow region with electron diffusivity χ e an order of magnitude lower than the average value across the plasma, suggesting an electron internal transport barrier (ITB) near the ECH heating location. Detailed profile analysis and equilibrium reconstructions suggest that the formation of these ITBs are correlated with off-axis values of the safety factor q being near 1. Furthermore, the ECH driven H-mode discharges demonstrate more rapid electron heating rate near the ECH deposition location than L-mode discharges with higher auxiliary ECH heating power. Additional modeling attributes this difference to the modification of electron heat transport in the core at the L-H transition, which also sustains the off-axis electron temperature peaks.

Physics↗
DOE OSTI2021

Confinement in electron heated plasmas in Wendelstein 7-X and ASDEX Upgrade; the necessity to control turbulent transport

In electron (cyclotron) heated plasmas, in both ASDEX Upgrade (L-mode) and Wendelstein 7-X, clamping of the ion temperature occurs at $T_\mathrm{i}$ ~ 1.5 keV independent of magnetic configuration. The ions in such plasmas are heated through the energy exchange power as ${n}_{\mathrm{e}}^{2}({T}_{\mathrm{e}}-{T}_{\mathrm{i}})/{T}_{\mathrm{e}}^{3/2}$, which offers a broad ion heating profile, similar to that offered by alpha heating in future thermonuclear fusion reactors. However, the predominant electron heating may put an additional constraint on the ion heat transport, as the ratio $T_\mathrm{e}T_\mathrm{i}$ > 1 can exacerbates ITG/TEM core turbulence. Therefore, in practical terms the strongly 'stiff' core transport translates into Ti-clamping in electron heated plasmas. Due to this clamping, electron heated L-mode scenarios, with standard gas fueling, in either tokamaks or stellarators may struggle to reach high normalized ion temperature gradients required in a compact fusion reactor. The comparison shows that core heat transport in neoclassically optimized stellarators is driven by the same mechanisms as in tokamaks. The absence of a strong H-mode temperature edge pedestal in stellarators, sofar (which, like in tokamaks, could lift the clamped temperature-gradients in the core), puts a strong requirement on reliable and sustainable core turbulence suppression techniques in stellarators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Divertor-safe nonlinear burn control based on a SOLPS parameterized core-edge model for ITER

Abstract For ITER operations, the range of desirable burning-plasma regimes with high fusion power output will be restricted by various operational constraints. These constraints include the saturation of ITER’s various heating and fueling actuators such as the neutral beam injectors, the ion and electron cyclotron heating systems, the gas puffing system, and the deuterium–tritium pellet injectors. In addition to these actuator constraints, the H-mode power threshold, divertor detachment, and the heat load on the divertor targets may apply limitations to ITER’s operational space. In this work, Plasma Operation Contour (POPCON) plots that map the aforementioned constraints to the temperature-density space are used to investigate which constraints are most limiting towards accessing regimes with high fusion power output. The presented POPCON plots are based on a control-oriented core-edge model that couples the nonlinear density and energy response models for the core-plasma region with SOLPS4.3 parameterizations for conditions in the edge-plasma regions (scrape-off-layer and divertor). Using this control-oriented core-edge model, a nonlinear burn controller, which aims to regulate the plasma temperature and density in the core-plasma region, is constructed in this work. This controller is augmented with an online optimization scheme that governs the control references such that the plasma can be guided towards regimes with high fusion powers while protecting the divertor targets from dangerously high heat loads. A closed-loop simulation study illustrates the capability of this burn control scheme.

Physics↗
DOE OSTI2023

Analysing the effects of heating and gas puffing in Proto-MPEX helicon and auxiliary heated plasmas

The Material Plasma Exposure Experiment (MPEX) is being constructed at Oak Ridge National Laboratory to investigate critical fusion reactor issues, such as plasma–material interactions (PMIs) under reactor-relevant conditions and time scales. The linear device Proto-MPEX was used as a test bed to address anticipated research and development issues associated with heating scenarios and establish the physics basis for MPEX. The SOLPS-ITER code suite has been applied to understand plasma and neutral transport in Proto-MPEX and to increase confidence in predictive simulations for MPEX. Coupling between COMSOL and SOLPS is performed to implement a 2D electron heating profile of the helicon source. The simulations show reasonable agreement with the experimental data for plasma with helicon and auxiliary electron cyclotron heating (ECH). Both Bohm and constant diffusion (D$_\perp$: 0.5 m 2 s –1 and $\chi_\perp$: 1 m 2 s –1 ) simulations show similar levels of agreement with respect to the sparse experimental data available, assuming a few per cent impurity concentration. ECH significantly increases the target electron temperature, however, the target electron density is reduced compared to helicon-only heated plasmas due to an increase in flow velocity and radial losses. The simulations show that further increasing the ECH power results in an increase in the target electron density due to increased recycling flux and ionization. The results indicate that ECH significantly enhances the target heat flux, with ECH power of 50 kW increasing the target heat flux from 0.4 to 17 MW m –2 . It is found that a small amount of gas puffing (GP) near the target plate can further increase the target heat fluxes at the higher ECH power cases, but the target heat flux is reduced at higher GP conditions due to a significant reduction in electron temperature via radiation. ECH and GP scenarios can generate a higher target flux, facilitating improved PMI studies with more reactor-relevant plasma conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Plasma heating technology

The operational environment for plasma heating systems presents unprecedented challenges for the success of magnetic fusion. This chapter discusses the current state of ion cyclotron and electron cyclotron heating systems and the research and development priorities needed to establish working solutions for these systems. While much progress has been made, there is much more work to be done to make fusion energy commercially viable. Research and development priorities include radiation-resistant structural and plasma facing materials, advanced manufacturing methods, new cooling methods, first-wall integrated actuators, improvements in power source efficiency, higher frequency gyrotrons, and improved overall system reliability.

Caughman, John↗
DOE OSTI2023

PFPO plasma scenarios for exploration of long pulse operation in ITER

Long Pulse Scenarios (LPS) in ITER foreseen during the Pre-Fusion Power Operation (PFPO) phase of the ITER Research Plan (IRP) are assessed using 1.5D transport simulations within the ASTRA framework. Such assessment is required to predict the operational space for LPS operation in PFPO, as well as to evaluate which physics processes for LPS operation during Fusion Power Operation (FPO) could be studied during PFPO. An important aspect in the development of LPSs in PFPO is to minimize lifetime consumption of the Central Solenoid (CS) for these scenarios. The maximum pulse length achievable for LPSs in PFPO with no consumption of CS lifetime (currents in CS coils $&LessSlantEqual;$30 kA per turn) has been assessed for a range of heating schemes and heating mixes, confinement regimes (L-mode and H-mode) and for helium and hydrogen plasmas. The operational space of LPS and pulse length has been explored through density scans with the Heating and Current Drive mix required for the FPO Q $&GreaterSlantEqual;$ 5 steady-state plasma scenario (namely Neutral Beam Injection and Electron Cyclotron Heating) including acceptable shine through losses on the first wall for both helium and hydrogen plasmas. Fast particle physics aspects that are common between FPO plasmas and LPS PFPO H-mode plasmas at low densities are studied including MHD stability analysis with the KINX code and non-perturbative critical gradient model based on high-n Toroidal Alfven Eigenmodes (TAE) stability kinetic ballooning code HINST calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Time dependent model for non-inductive ECH X-I current ramp-up for SHPD tokamak facility

Non-inductive (NI) plasma current start-up and ramp-up is an important research topic for spherical tokamak (ST) based reactors and fusion pilot plant (FPP). For a compact FPP, the OH flux availability is highly restricted due to its compact geometry. Efficient fundamental extraordinary mode (X-I) electron cyclotron heating (ECH) current start-up and ramp-up regime was identified for a reactor-like high toroidal magnetic field range which has more than a hundred times higher current drive efficiency compared to more conventional ECH methods for the relevant start-up temperature range. High current drive efficiency is possible due to the strong X-I fundamental ECH interaction only with unidirectional passing electrons constrained by the wave accessibility conditions. Here, we extend the X-I electron cyclotron current drive (ECCD) investigation to a time dependent model to simulate the non-inductive current ramp-up to 10 MA for the Sustained High-Power Density (SHPD) facility. As the X-I ECCD driven current I EC rises, due to the back EMF driven negative current, the net plasma current Ip rises more slowly with the current resistive time scale. For tokamak confinement time (both L-mode and H-Mode) which tends to rise with I p , a positive feedback results and even with constant applied ECH power, T e0 , I EC , and I p can continue to rise to very high values. However, in a realistic situation, the T e0 rise should saturate due to a number of factors such as enhanced core radiation and increased power loss at high temperature. To simulate this effect, we adopt a maximum T e0 model which would limit the temperature rise to certain T e0 . With this model, we investigated the current ramp-up for various ECH power levels and the maximum T e0 of 15, 20, and 25 keV. We find that while the power required is reduced with increasing T e0 limit due to increased current drive efficiency, the time to reach 10 MA tends to go up due to the reduced plasma resistivity for the higher T e0 limit. We also find for a given Te0 limit, the time to reach 10 MA tends to be reduced by increasing the applied ECH power by over driving the current ramp-up where I EC is driven at significantly higher level than 10 MA. While the current ramp-up time may not be an issue for the steady-state reactor systems, if it is desirable to minimize the current ramp-up time, it is prudent to have a sufficient ECH power for current over-drive and have some T e0 limiting tools such as impurity seeding for enhanced radiation. In conclusion, a well-controlled NI ECH start-up also has a potential of improving the tokamak start-up reliability and avoid run-away electrons while the NI off-axis current drive could enhance MHD stability and plasma performance improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗