Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering - Electronic and electrical engineering, Materials science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

ELECTRIC FIELD-ASSISTED DIFFUSION WELDING TO FABRICATE ALLOY 617 COMPACT HEAT EXCHANGERS

Compact heat exchangers are of interest for a number of applications including advanced reactors. Alloy 617 is one of the top candidate materials for the gas-cooled reactor intermediate heat exchanger. Previous endeavors to diffusion weld Alloy 617 utilized hot pressing (HP). It was reported that grain boundary migration across the interface was hindered by extensive precipitation. Bonds of this nature have been observed to reduce the elevated-temperature mechanical properties compared to the wrought-product form. It was hypothesized that the electric current applied during electric-field-assisted sintering (EFAS) can overcome these challenges, resulting in improved diffusion welding (DW). This study investigated DW of Alloy 617 via EFAS. Stacks composed of three sheets that were 20 mm in diameter were welded using EFAS. Specimens were welded with an applied electric current, a pressure of 30 MPa, hold time of 30 min, and temperatures of 1050°C, 1100°C, and 1150°C. DW using HP as the zero-current analog of EFAS was also performed at the most promising EFAS conditions. Results revealed that both the applied electric current and temperature played a key role in precipitation and grain boundary migration in diffusion-welded Alloy 617. Precipitates were observed at the interface of the hot-pressed samples which limited grain boundary migration. Electric current was found to prevent precipitate formation along the interface at 1150°C. The electric current coupled with a temperature of 1150°C during EFAS resulted in significant grain boundary migration across the interface.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Fully‐Printed Ion Sensor Arrays for Measuring Agricultural Nitrogen and Potassium Concentrations Using Nernstian and AI Models

Abstract The chemical composition of growing media is a key factor for plant growth, impacting agricultural yield and sustainability. However, there is a lack of affordable chemical sensors for ubiquitous nutrient ion monitoring in agricultural applications. This work investigates using fully printed ion‐sensor arrays to measure the concentrations of nitrate, ammonium, and potassium in mixed‐electrolyte media. Ion sensor arrays composed of nitrate, ammonium, and potassium ion‐selective electrodes and a printed silver‐silver chloride (Ag/AgCl) reference electrode are fabricated and characterized in aqueous solutions in a range of concentrations that encompass what is typical for agricultural growing media (0.01 m m –1 m ). The sensors are also tested in mixed‐electrolyte solutions of NaNO 3 , NH 4 Cl, and KCl of varying concentrations, and the recorded potentials are input into Nernstian and artificial neural network models to compare the prediction accuracy of the models against ground truth. The artificial neural network models demonstrated higher accuracy over the Nernstian model, and the model using only ion‐sensor inputs is 7.5% more accurate than the Nernstian model under the same conditions. By enabling more precise and efficient fertilizer application, these sensor arrays coupled to computational models can help increase crop yields, optimize resource use, and reduce environmental impact.

Goodrich, Payton [University of California Berkele↗
NASA NTRS1983

Proceedings of the 21st Project Integration Meeting

Progress made by the Flat Plate Solar Array Project during the period April 1982 to January 1983 is described. Reports on polysilicon refining, thin film solar cell and module technology development, central station electric utility activities, silicon sheet growth and characteristics, advanced photovoltaic materials, cell and processes research, module technology, environmental isolation, engineering sciences, module performance and failure analysis and project analysis and integration are included.

Source record↗
DOE OSTI2024

An Electrical Resistance Diagnostic for Conductivity Monitoring in Laser Powder Bed Fusion

With the growing interest in metal additive manufacturing using laser powder bed fusion (LPBF), there is a need for advanced in-situ nondestructive evaluation (NDE) methods that can dynamically monitor manufacturing process-related variations, that can be used as a feedback mechanism to further improve the manufacturing process, leading to parts with improved microstructural properties and mechanical properties. Current NDE techniques either lack sensitivity beyond build layer, are costly or time-consuming, or are not compatible for in-situ integration. In this research, we develop an electrical resistance diagnostic for in-situ monitoring of powder fused regions during laser powder bed fusion printing. The technique relies on injecting current into the build plate and detecting voltage differences from conductive variations during printing using a simple, cheap four-point electrode array directly connected to the build plate. A computational model will be utilized to determine sensitivities of the approach, and preliminary experiments will be performed during the printing process to test the overall approach.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Field-Driven Simulations to Probe the Impact of Ionic Correlations on Solution Transport Coefficients in Binary, Ternary, and Reciprocal Quaternary Aqueous Electrolytes

Ionic correlations play a critical role in governing transport properties of mixed-salt aqueous electrolyte solutions, yet their quantitative characterization remains challenging, particularly for multicomponent aqueous systems. Here, we develop a general nonequilibrium molecular dynamics framework to efficiently compute Onsager transport coefficients and ionic correlations in mixed-salt aqueous solutions. Using field-driven simulations, we obtain accurate Onsager matrices for LiCl/ KCl, KCl/KBr, and LiBr/KCl electrolyte solutions with significantly reduced computational cost relative to equilibrium Green−Kubo methods. The framework enables direct assessment of how attractive cation−anion and repulsive like-ion interactions contribute to conductivity and salt diffusivity across compositions. While static ion pairing exhibits strong composition dependence, dynamic ion correlations remain nearly invariant, leading to constant deviations from Nernst−Einstein predictions. These results highlight the disconnect between static ion association and dynamic transport correlations, and they establish a transferable approach for analyzing ion transport in complex electrolyte environments relevant to separation processes and electrochemical systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tunable plasmon-enhanced second-order optical nonlinearity in transition metal dichalcogenide nanotriangles

The development of nanomaterials with a large nonlinear susceptibility is essential for nonlinear nanophotonics. Here we show that transition metal dichalcogenide (TMD) nanotriangles have a large effective second-order susceptibility [χ (2) ] at midinfrared to near-infrared frequencies owing to their broken centrosymmetry. χ (2) is calculated within the density-matrix formalism that accounts for dissipation and screening. χ (2) peaks in the vicinity of both two-photon resonances (specified by the geometry) and plasmon resonances (tunable via the carrier density). Aligning the resonances yields the values of χ (2) as high as 10 –6 m/V. These findings underscore the potential of TMD nanotriangles for nonlinear nanophotonics, particularly second-harmonic generation.

0-dimensional systems↗
DOE OSTI2020

Effect of frequency and applied voltage of an atmospheric-pressure dielectric-barrier discharge on breakdown and hydroxyl-radical generation with a liquid electrode

This work examines the effect of the frequency and peak applied voltage on hydroxyl-radical generation in a dielectric-barrier plasma discharge between a metallic needle electrode and one electrode covered with dielectric. The authors examine a system that can expose up to 96 liquid samples in an automated fashion without human intervention beyond setting the initial software configuration. Then, hydroxylradical concentration, measured through coumarin fluorescence, was measured for 5 s plasma exposures generated under different highvoltage conditions with frequencies from 2 to 16 kHz and amplitudes from 4 to 9 kV. Their results show that an increase in frequency and/or applied voltage, within the range prescribed above and the limits of the high-voltage power supply, can yield up to a 150% increase in fluorescence with an equivalent hydroxyl-radical increase. Applications using typical previous methods, such as the Fenton Reaction, are limited in that they continuously generate hydroxyl radicals over millisecond and longer intervals. These results establish the electrical parameters that can now be applied to polymers, like proteins, which show three dimensional structures that are flexible and fluctuate on a microsecond and nanosecond time scale, with hydroxyl-radical generation on this time scale using this device. Additionally, plasma exposures may be optimized for a great variety of proteins, devices and techniques, where hydroxyl-radical generation is of utmost importance, reducing exposure time and potential subjection of samples to harmful side effects.

42 ENGINEERING↗
DOE OSTI2021

Electrical conductivity of Sn at high pressure and temperature

To date, temperature and conductivity have many outstanding implications in extreme environments but are yet to be fully understood under high pressure and temperature dynamic conditions. Here, we introduce an approach to provide high quality electrical conductivity results under dynamic loading conditions. Emphasis is given to address the skin depth effect's influence in a dynamic loading experiment by using thin films. The thin film samples in this study were at least 100 times thinner than previous samples in dynamic electrical conductivity experiments, increasing the current density to its full potential across the sample's entire cross section. Consideration of the skin depth accounts for at minimum a 4× scaling factor to the final electrical conductivity result that has been neglected in previous dynamic electrical conductivity studies. We also obtained improved signal-to-noise ratio with custom diagnostics optimized for better electrical impedance matching. Furthermore, these considerations were applied to Sn to assess electrical conductivity at elevated pressure and temperature. The high signal-to-noise ratio with reduced skin depth influence results in Sn allowing observation of the conductivity changes related to solid-to-solid and solid-to-liquid phase transitions. Additionally, we calculate the Sn thermal conductivity using the Wiedemann-Franz law for our experiments and compare against thermal transport dependent temperature measurements from previous work.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Vertical z-axis discontinuous carbon fibers for improved lightning strike performance of continuous fiber-reinforced polymer composites

Effective lightning strike protection for critical aerospace and wind applications requires high electrical conductivity to dissipate current efficiently. However, polymer matrix composites face a challenge due to their inherently insulating nature. While conventional carbon fiber-reinforced composites (CFRP) exhibit electrical conductivity in the planar direction, achieving through-thickness conductivity remains an ongoing challenge. In this work, we have undertaken the fabrication of CFRP interleaved with vertically oriented carbon fibers (Z-fiber) to impart higher electrical conductivity along the thickness direction. Two Z-fiber composite variations are prepared: Z-1 with a single layer of Z-fiber and Z-5 with five interleaved layers and compared with no Z-fiber layer (Z-0) composite. The composite panels were subjected to lab-scale lightning strike tests with a current magnitude of 100 kA. To emulate real-world service conditions, an aerospace-grade paint coating was applied to the composite laminates. Comparative analysis shows Z-1 reduces damage diameter to ∼22 mm compared to Z-0 (∼26 mm), while Z-5 exhibits the least damage (∼16.7 mm), confirmed by optical microscopy. Z-5 demonstrates nine times higher through-thickness electrical conductivity than Z-0, reducing electrical anisotropy substantially. Thermal-electric finite element damage modeling predicts surface damage within 6% of experimental values for both Z-0 and Z-5 composites. Flexural tests post-lightning reveal Z-5 retains 66% flexural strength and 86% modulus, significantly better than Z-0, which retains less than 40% for both properties. This study highlights the efficacy of Z-fiber composites in lightning strike protection, offering improved through-thickness conductivity and mechanical property retention.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Metal forming and working of stabilized nanocrystalline Cu-Ta for electrical contacts

The commercialization of nanocrystalline metals and alloys is currently entering a renaissance period. Many of the processing and consolidation challenges that have haunted them are now more fully understood, opening the doors for stabilized nanocrystalline metals to be produced on a bulk scale. While challenges remain, the increased volume at which these materials are being supplied is for the first time allowing for investigations into more traditional methods of metal working, such as extruding, rolling, forming, and forging. Recently, the manufacturing science has been developed to allow nanocrystalline Cu-Ta alloys to progress to this point. This article therefore builds upon the last decade of evolutionary progression within the family of stabilized nanocrystalline Cu-Ta alloys by presenting some of the first findings related to scaled powder synthesis, production of billets, thin sheets, and foils. Here, the mechanical performance and physical properties relevant to forming electrical contacts and pins including, tensile, J-integral fracture toughness, Charpy Impact, bi-axial tension, and conductivity are reported. This introductory investigation into forming such a novel material, provides evidence to these alloys potential at bridging the gap between being a scientific curiosity to that of a real engineering material.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Single-Step Shear-Based Deformation Processing of Electrical Conductor Wires

Commercial electrical conductor wires are currently produced from aluminum alloys by multi-step deformation processing involving rolling and drawing. These processes typically require 10 to 20 steps of deformation, since the plastic strain or reduction that can be imposed in a single step is limited by material workability and process mechanics. Here, we demonstrate a fundamentally different, single-step approach to produce flat wire aluminum products using machining-based deformation that also ensures adequate material workability in the formed product. Two process routes are proposed: (1) chip formation by free-machining (FM), with a post-machining, light drawing reduction (<20%) to achieve desired finish and (2) constrained chip formation by large strain extrusion machining (LSEM). Using commercially pure aluminum conductor alloys (Al 1100 and EC1350) as representative material systems, we demonstrate key features of the machining-based processing, including (a) single-step processing to achieve flat wire geometries, (b) surface finish (Ra = 0.2 to 1.0 μm) comparable to that of commercial wire products made by drawing/rolling, (c) deformation control independent of wire size, and (d) hardness increases of 50–150% over that of annealed wires, while retaining high electrical conductivity (>56% IACS). Here, the wire microstructure, which can also be varied via the large-strain deformation parameters, is correlated with mechanical and electrical properties. Implications for commercial manufacture of flat wire products are discussed.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

ICME for NASA Aerospace Applications: Batteries for Electric Aviation

NASA’s approach to computational materials modeling is detailed in the NASA Vision 2040 Roadmap for Multiscale Modeling and Simulation of Materials and Systems. This report is in the spirit of national initiatives such as the Material Genome Initiative (MGI), Integrated Computational Materials Engineering (ICME), and others. We utilize a combination of fundamental modeling, computational high-throughput screening, and data science methods, e.g., machine learning, are used to find innovative solutions to NASA or national technology challenges. Applications of interest are wide ranging from advanced alloys to batteries to coatings, among others. In this talk, we present three examples for recent work related to NASA applications. First, doping advanced sulfur battery cathodes with selenium boosts electrical conductivity important for electric aircraft applications. First principles calculations will be discussed that result in compositional design maps for these materials. Second, development of icephobic coatings is important to mitigate safety hazards associated with icing for aircraft. Molecular dynamics simulations are reported for ice-surface interfaces to understand adhesion mechanisms and help screen optimal ice-phobic coatings. Third, shape memory alloys have numerous applications as actuators, superelastic materials, etc. for aerospace. We report machine learning models that predict martensitic transition temperatures across a broad swath of compositional space.

John Lawson↗
DOE OSTI2023

Multi-scale modeling of the electric field assisted sintering process

The electric field assisted sintering (EFAS) process involves tightly coupled physics that influence microstructural evolution in the particles being compacted. It is also an inherently multi-scale phenomenon, with the microstructure of the compact influencing the subsequent engineering-scale response of the sintering system. To improve understanding of how processing parameters influence microstructural evolution, we have developed a multi-scale modeling approach that couples a continuum-level model of the sintering system with a phase-field model for microstructural evolution of particles within the compact. The phase-field model couples the effect of chemical and electrical driving forces on microstructural evolution and includes the effect of charged defect segregation to surfaces and grain boundaries; this segregation leads to enhanced defect transport and heat generation at these interfaces in response to applied electric field. The effect of enhanced heat generation on particle neck growth and the influence of microstructural evolution on the engineering-scale model are demonstrated.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Exploding Bridgewire (EBW) Detonators: An Example of Synergistic Multiphysics

Exploding bridgewire (EBW) detonators are highly temporally reproducible explosive devices that require the rapid discharge of a high‐voltage capacitance to operate and so are immune to most of the accidental hazards associated with traditional electric detonators. They have been demonstrated to be safe enough for use in high‐consequence explosive applications. Despite continued use for over 82 years, understanding the exact mechanism of operation has remained elusive. Various researchers have ascribed either deflagration‐to‐detonation (DDT) or shock‐to‐detonation (SDT) phenomena observed in other explosive events to explain the science behind the successful engineering; however, a rigorous justification has been absent. Previously, we have demonstrated a complex interaction in EBW detonators between large electrical currents, non‐equilibrium thermodynamic material states, plasma physics, powder compaction phenomena, shock physics, photochemistry, and rapid conventional explosive chemical reaction processes. Specifically, we have made progress in understanding the complex multiphysics that operates in these detonators and demonstrating that it is a serendipitous synergy between UV light emitted from the arc formed as the bridge is electrically exploded and the accompanying short‐duration shock transmitted into the explosive powder bed that allows these devices to function at practical capacitor sizes and charge voltages. This insight not only places the topic on a firmer scientific footing but potentially enables new approaches to safe detonator design.

36 MATERIALS SCIENCE↗