Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOATS AND HULLS - DESIGN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

32 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1929

Water-Pressure Distribution on Seaplane Float

The investigation presented in this report was conducted for the purpose of determining the distribution and magnitude of water pressures likely to be experienced on seaplane hulls in service. It consisted of the development and construction of apparatus for recording water pressures lasting one one-hundredth second or longer and of flight tests to determine the water pressures on a UO-1 seaplane float under various conditions of taxiing, taking off, and landing. The apparatus developed was found to operate with satisfactory accuracy and is suitable for flight tests on other seaplanes. The tests on the UO-1 showed that maximum pressures of about 6.5 pounds per square inch occur at the step for the full width of the float bottom. Proceeding forward from the step the maximum pressures decrease in magnitude uniformly toward the bow, and the region of highest pressures narrows toward the keel. Immediately abaft the step the maximum pressures are very small, but increase in magnitude toward the stern and there once reached a value of about 5 pounds per square inch. (author)

Thompson, F L↗
DOE OSTI2023

The NASA Floater: 15MW Ultra-Light Concrete Hull with Sea-Water Ballast Tuned Mass Damper

In this project, UMaine developed the VolturnUS+ platform; a new 15MW+ ultra-light-weight, corrosion-resistant, concrete floating offshore wind turbine (FOWT) equipped with novel patent pending Heel Tank damping technology. UMaine developed this damping technology to reduce FOWT motions using existing onboard sea-water ballast, which has been integrated into the concrete cruciform hull resulting in reduced platform rigid body motions leading to a lighter hull, increased turbine performance, and a lower LCOE.

17 WIND ENERGY↗
NASA NTRS1952

Hydrodynamic Impact of a System with a Single Elastic Mode II : Comparison of Experimental Force and Response with Theory

Hydrodynamic impact tests were made on an elastic model approximating a two-mass spring system to determine experimentally the effects of structural flexibility on the hydrodynamic loads encountered during seaplane landing impacts and to correlate the results with theory. A flexible seaplane was represented by a two-mass spring system consisting of a rigid prismatic float connected to a rigid upper mass by an elastic structure. The model had a ratio of sprung mass to hull mass of 0.6 and a natural frequency of 3.0 cycles per second. The tests were conducted in smooth water at fixed trims and included both high and low flight-path angles and a range of velocity. Theoretical and experimental comparisons indicated that the theoretical results agreed well with the experimental results.

Miller, Robert W↗
DOE OSTI2023

1:70-Scale Model Testing of the Reference OpenSource Controller (ROSCO) on the IEA-Wind 15MW Reference Wind Turbine Including Floating Feedback: Preprint

This paper presents results from the Floating Offshore-wind Controls Advanced Laboratory (FOCAL) Experimental campaign performed at the University of Maine's (UMaine's) Harold Alfond Wind/Wave Ocean Engineering Laboratory (W2). The project involves four Froude-scaled test campaigns considering the International Energy Agency (IEA) Wind 15MW Reference Wind Turbine deployed on the VolturnUS-S semi-submersible platform with tuned-mass damper (TMD) elements in the hull. The turbine employs real-time rotor torque and blade pitch control through the Reference OpenSource Controller (ROSCO), including the additional control strategies of ROSCO's thrust peak shaving and a floating feedback control loop. Results with the floating feedback control are considered in this paper and show a significant reduction in platform pitch motion and loads around the platform pitch natural frequency with minimal negative impact of rotor power quality.

controls↗
NASA NTRS1937

Tank Tests of NACA Model 40 Series of Hulls for Small Flying Boats and Amphibians

The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.

Parkinson, John B↗
NASA NTRS1946

Waters Loads on the XJL-1 Hull as Obtained in Langley Impact Basin, TED No. NACA 2413.3

An investigation was conducted in the Langley impact basin of the water loads on a half scale model of the XJL-1 hull whose forebody has a vee bottom with exaggerated chine flare. The impact loads, moments, and pressures were determined for a range of landing conditions. A normal full-scale landing speed of 86 miles per hour was represented with effective flight paths ranging from 0.6deg to 11.6deg. Landings were made with both fixed trim and free-to-trim mounting of the float over a trim range of -15deg to 12deg into smooth water and into waves having equivalent full-scale length. of 120 feet and heights ranging from 1 to 4 feet. All data and results presented in this report are given in terms of equivalent full-scale values. Summary tables and illustrative plots are used in presenting the material. The following maximum values of load and pressure are those which are apropos for effective flight paths less than 6.5deg which was the maximum value obtained in tests with the XJL-1 hull model representing full-scale landings with vertical velocity of 4.5 feet per second into 4-foot waves. The maximum local pressure on the flat portion of the bottom is 130 pounds per square inch which was measured on a 2-inch-diameter circular area near the step. The maximum local pressure obtained in the curved area near the chines is 200 pounds per square inch. This pressure was also measured near the step.

Steiner, Margaret F.↗
NASA NTRS1936

Tank Tests of Models of Floats for Single-float Seaplanes First Series.

Large models of the Mark V and Mark VI floats used for single float seaplanes (National Advisory Committee for Aeronautics (NACA) models 41-A and 41-B, respectively) were tested in the NACA tank to provide general test data for typical single floats and a basis for possible improvements of their form. The resistance of model 41-B was greater than that of model 41-A, either when free to trim or at the best trim angle for each. The resistance of model 35-B (a pointed step hull tested free to trim) was less than either of the models at the hump speed, greater at intermediate planing speeds, and less at the speeds and loads near get-away, although the spray was generally worse owing to the absence of transverse flare. The results of the fixed-trim tests of model 41-A were cross plotted to obtain data at the angle for zero trimming moment and at the best trim angle. The trims assumed by models 41-A and 41-B, when tested free to trim, were found to be excessive at the hump speed. The corresponding trim of model 35-B was found to be approximately 3 degrees lower because of the lower angle of afterbody keel used in this model, and the maximum hump resistance was 15 percent lower.

Parkinson, J B↗
NASA NTRS1997

STS-86 Day 07 Highlights

On this seventh day of the STS-86 mission, the flight crew, Cmdr. James D. Wetherbee, Jr., Pilot Michael J. Bloomfield, Mission Specialists Scott E. Parazynski, Jean-Loup Chretien, Vladimir G. Titov, Wendy B. Lawrence and Mike Foale are seen in preparations for a planned five-hour spacewalk to retrieve four experiment packages and to test tools and techniques for construction of the International Space Station. Parazynski and Titov are seen floating out of a hatch on Atlantis' tunnel adapter in front of the Orbiter Docking System to begin their spacewalk. They then affix a 121-pound instrument called a Solar Array Cap to the Docking Module for future use by Russian cosmonauts to seal off a suspected breach in the hull of the Spektr Module.

Source record↗
NASA NTRS1948

Hydrodynamic Characteristics of an Aerodynamically Refined Planing-Tail Hull

The hydrodynamic characteristics of an aerodynamically refined planing-tail hull were determined from dynamic model tests in Langley tank no. 2. Stable take-off could be made for a wide range of locations of the center of gravity. The lower porpoising limit peak was high, but no upper limit was encountered. Resistance was high, being about the same as that of float seaplanes. A reasonable range of trims for stable landings was available only in the aft range of center-of-gravity locations.

McKann, Robert↗
NASA NTRS1978

Desirable floating-point arithmetic and elementary functions for numerical computation

The topics considered are: (1) the base of the number system, (2) precision control, (3) number representation, (4) arithmetic operations, (5) other basic operations, (6) elementary functions, and (7) exception handling. The possibility of doing without fixed-point arithmetic is also mentioned. The specifications are intended to be entirely at the level of a programming language such as FORTRAN. The emphasis is on convenience and simplicity from the user's point of view. Conforming to such specifications would have obvious beneficial implications for the portability of numerical software, and for proving programs correct, as well as attempting to provide facilities which are most suitable for the user. The specifications are not complete in every detail, but it is intended that they be complete in spirit - some further details, especially syntatic details, would have to be provided, but the proposals are otherwise relatively complete.

Hull, T. E.↗