Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW CHARACTERISTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Investigations of three dimensional flow characteristics in a three bladed rocket pump inducer

Because of the long and narrow passages between the blades of a rocket pump inducer, major effects from turbulence and viscosity make the flow through such a device truly three-dimensional and therefore difficult to measure or predict. To investigate the flow characteristics, conventional and three-dimensional hot-wire probe measurements were conducted in a model inducer 3 ft in diameter. Blade-to-blade variation of the three components of velocity at the exit and the corresponding turbulence intensities were obtained by means of hotwire probes aligned in the three coordinate directions. Analysis of the three-dimensional inviscid flow field led to qualitative prediction of the flow characteristics. Extensive measurements and theoretical analyses of the flow field showed that blade blockage, viscosity, and blade boundary layer interactions are the dominant influences on flow in this type of turbomachinery.

Poncet, A.↗
NASA NTRS1978

Experimental perfect-gas study of expansion-tube flow characteristics

Results of an experimental investigation of expansion tube flow characteristics performed with helium test gas and acceleration gas are presented. The use of helium, eliminates complex real gas chemistry in the comparison of measured and predicted flow quantities. The driver gas was unheated helium at a nominal pressure of 33 MN sq m. The quiescent test gas pressure and quiescent acceleration gas pressure were varied from 0.7 to 50 kN/sq m and from 2.5 to 53 N/sq m, respectively. The effects of tube-wall boundary layer growth and finite secondary diaphragm opening time were examined through the variation of the quiescent gas pressures and secondary diaphragm thickness. Optimum operating conditions for helium test gas were also defined.

Shinn, J. L.↗
NASA NTRS1952

Experimental Study of Isothermal Wake-Flow Characteristics of Various Flame-Holder Shapes

An investigation of the isothermal wake-flow characteristics of several flame-holder shapes was carried out in a 4- by 4-inch flow chamber. The effects of flame-holder-shape changes on the characteristics of the Karman vortices and thus on the recirculation zones to which experimenters have related the combustion process were obtained for several flame holders. The results may furnish a basis of correlation, of combustion efficiency and stability for similarly shaped flame holders in combustion studies. Values of the spacing ratio-(ratio of lateral spacing to longitudinal spacing of vortices] obtained for the various shapes approximated the theoretical value of 0.36 given by the Karman stability analysis. Variations in vortex strength of more than 200 percent and in frequency of more than 60 percent were accomplished by varying flame-holder shape. A maximum increase in the recirculation parameter of 56 percent over that for a conventional V-gutter was also obtained. Varying flameholder shape and size enables the designer to select many schedules of variations in vortex strength and frequency- not obtainable by changing size only and may make it possible to approach theoretical maximum vortex strength for any given frequency.

Younger, G. G.↗
NASA NTRS1983

End wall flow characteristics and overall performance of an axial flow compressor stage

This review indicates the possible future directions for research on endwall flows in axial flow compressors. Theoretical investigations on the rotor blade endwall flows in axial flow compressors reported here include the secondary flow calculation and the development of the momentum integral equations for the prediction of the annulus wall boundary layer. The equations for secondary vorticity at the rotor exit are solved analytically. The solution includes the effects of rotation and the viscosity. The momentum integral equations derived include the effect of the blade boundary layers. The axial flow compressor facility of the Department of Aerospace Engineering at The Pennsylvania State University, which is used for the experimental investigations of the endwall flows, is described in some detail. The overall performance and other preliminary experimental results are presented. Extensive radial flow surveys are carried out at the design and various off design conditions. These are presented and interpreted in this report. The following experimental investigations of the blade endwall flows are carried out. (1) Rotor blade endwall flows: The following measurements are carried out at four flow coefficients. (a) The rotor blade static pressures at various axial and radial stations (with special emphasis near the blade tips). (b) The hub wall static pressures inside the rotor blade passage at various axial and tangential stations. (2) IGV endwall flows: The following measurements are carried out at the design flow coefficient. (a) The boundary layer profiles at various axial and tangential stations inside the blade passage and at the blade exit. (b) Casing static pressures and limiting streamline angles inside the blade passage.

Sitaram, N.↗
NASA NTRS1994

Low-Disturbance Flow Characteristics of the NASA-Ames Laminar Flow Supersonic Wind Tunnel

A unique, low-disturbance (quiet) supersonic wind tunnel has been commissioned at the NASA-Ames Fluid Mechanics Laboratory (FML) to support Supersonic Laminar Flow Control (SLFC) research. Known as the Laminar Flow Supersonic Wind Tunnel (LFSWT), this tunnel is designed to operate at potential cruise Mach numbers and unit Reynolds numbers (Re) of the High Speed Civil Transport (HSCT). The need to better understand the receptivity of the transition phenomena on swept (HSCT) wings to attachment-line contamination and cross-flows has provided the impetus for building the LFSWT. Low-disturbance or "quiet" wind tunnels are known to be an essential part of any meaningful boundary layer transition research. In particular, the receptivity of supersonic boundary layers to wind tunnel disturbances can significantly alter the transition phenomena under investigation on a test model. Consequently, considerable effort has gone into the design of the LFSWT to provide quiet flow. The paper describes efforts to quantify the low-disturbance flows in the LFSWT operating at Mach 1.6, as a precursor to transition research on wing models. The research includes: (1) Flow measurements in both the test section and settling chamber of the LFSWT, using a full range of measurement techniques; (2) Study of the state of the test section boundary layer so far by using a single hot-wire mounted above the floor centerline, with and without boundary layer trips fitted at the test section entrance; (3) The effect of flow quality of unsteady supersonic diffuser flow, joint steps and gaps, and wall vibration.

Wolf, Stephen W. D.↗
NASA NTRS1997

Quiet Flow Characteristics of the NASA-Ames Laminar Flow Supersonic Wind Tunnel for Mach 1.6 Transition Studies

Low-disturbance or 'quiet' wind tunnels are an essential part of any meaningful boundary layer transition research. In particular, the receptivity of supersonic boundary layers to wind tunnel disturbances can significantly alter the transition phenomena under investigation on a test model. Consequently, considerable study has gone into the design of a new wind tunnel to provide quiet (low-disturbance) flow, encompassing both theoretical and experimental efforts. Our pilot (eighth-scale) supersonic wind tunnel was reported in 1992. NASA-Ames Fluid Mechanics Laboratory (FML) commissioned a quiet wind tunnel in 1994 to support Supersonic Laminar Flow Control (SLFC) research. Known as the Laminar Flow Supersonic Wind Tunnel (LFSWT), this tunnel is designed to operate at potential cruise Mach numbers and unit Reynolds numbers (Re) of the High Speed Civil Transport (HSCT). The need to better understand the transition phenomena on the leading edge region of swept (HSCT) wings provided the impetus for building the LFSWT. Additional information is contained in the original extended abstract.

Wolf, Stephen W. D.↗
NASA NTRS1977

Flow characteristics in an expansion tunnel as inferred from velocity measurements

A photoionization technique was used to study flow characteristics in an expansion tunnel. Vertical surveys of the axial component of flow velocity just downstream from the nozzle exit were obtained, and estimates of freestream density were inferred from the velocity measurement technique. The pitot pressure was measured and compared to the average axial component of velocity as a function of time for the two cases when air and CO2 were used as test gases. Vertical velocity and static density profiles at the nozzle exit are presented for the case when CO2 was used as test gas. Experimental results were used to determine the diameter and uniformity of the test core at the nozzle exit and the duration of the quasi-steady flow period. These data are relevant to evaluation of the suitability of operating an expansion tube as an expansion tunnel. The expansion tunnel is an expansion tube with a conical nozzle positioned at the exit of the acceleration section, so that nozzle entrance flow conditions are hypersonic and characterized by hypervelocity.

Miller, C. G.↗
NASA NTRS2002

Effects of Humidity On the Flow Characteristics of PS304 Plasma Spray Feedstock Powder Blend

The effects of environmental humidity on the flow characteristics of PS304 feedstock have been investigated. Angular and spherical BaF2-CaF2 powder was fabricated by comminution and by atomization, respectively. The fluorides were added incrementally to the nichrome, chromia, and silver powders to produce PS304 feedstock. The powders were dried in a vacuum oven and cooled to a Tom temperature under dry nitrogen. The flow of the powder was studied from 2 to 100 percent relative humidity (RH) The results suggest that the feedstock flow is slightly degraded with increasing humidity below 66 percent RH and is more affected above 66 percent RH. There was no flow above 88 percent RH. Narrower particle size distributions of the angular fluorides allowed flow up to 95 percent RH. These results offer guidance that enhances the commercial potential for this material system.

Stanford, Malcolm K.↗
NASA NTRS1950

Preliminary analysis of problem of determining experimental performance of air-cooled turbine II : methods for determining cooling-air-flow characteristics

In the determination of the performance of an air-cooled turbine, the cooling-air-flow characteristics between the root and the tip of the blades must be evaluated. The methods, which must be verified and the unknown functions evaluated, that are expected to permit the determination of pressure, temperature, and velocity through the blade cooling-air passages from specific investigation are presented.

FLOW, COMPRESSIBLE↗