Search NASA⌕ Search

SEARCH · Search NASA

Results for “FRACTURE MECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Benchmarking of Probabilistic Fracture Mechanics Models in Grizzly

In 2020, as part of contract/task order 31310019N0006/31310020F0060, the Nuclear Regulatory Commission tasked Idaho National Laboratory (INL) with benchmarking the MOOSE/GRIZZLY code against the NRC’s Fracture Analysis of Vessels - Oak Ridge (FAVOR), version 16.1 code. Both codes can predict large light-water reactor vessel integrity deterministically and probabilistically. In fact, such predictions are the primary purpose of the FAVOR code, and are a main focus of the GRIZZLY code, although GRIZZLY is capable of modeling a wider range of geometries and problems. The vessel integrity modeling capabilities of the GRIZZLY code are still under development and being gradually expanded, and the capability to model vessel fracture by crack growth has not yet been integrated into GRIZZLY (although it does exist in pre-release versions). Thus, the present benchmark study focused on comparing predictions for the conditional probability of crack growth initiation (CPI) between GRIZZLY and FAVOR v16.1. The present benchmarking study expands on a previous study completed in 2020, which focused on single plate regions, various flaw types, and full vessel studies. The previous study was limited in scope and revealed some relatively large discrepancies, particularly in the case of weld regions. In the present study, detailed investigations into the sources of discrepancies between GRIZZLY and FAVOR were performed, with a focus on weld regions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Grain-boundary fracture mechanisms in Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolytes: When phase transformation acts as a temperature-dependent toughening mechanism

Garnet-type, solid electrolytes, such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising alternative to liquid electrolytes for lithium-metal batteries. However, such solid-electrolyte materials frequently exhibit undesirable lithium (Li) metal plating and fracture along grain boundaries. In this work, we employ atomistic simulations to investigate the mechanisms and key fracture properties associated with intergranular fracture along one such boundary. Our results show that, in the case of a Σ5 (310) grain boundary, this boundary exhibits brittle fracture behavior, i.e. the absence of dislocation activity ahead of the propagating crack tip, accompanied with a decrease in work of separation, peak stress, and maximum stress intensity factor as the temperature increases from 300 K to 1500 K. As the crack propagates, we predict two temperature-dependent Li clustering regimes. For temperatures at or below 900 K, Li tends to cluster in the bulk region away from the crack plane driven by a void-coalescence mechanism concomitant a simultaneous cubic-to-tetragonal phase transition. The tetragonalization of LLZO in this temperature regime acts as an emerging toughening mechanism. At higher temperatures, this phase transition mechanism is suppressed leading to a more uniform distribution of Li throughout the grain-boundary system and lower fracture properties as compared to lower temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microscale drivers and mechanisms of fracture in post-processed additively manufactured Ti–6Al– 4 V

Herein, we focus on understanding the microstructure-fracture correlations in a Ti–6Al– 4 V alloy additively manufactured via electron beam melting (EBM) and subjected to various post-process heat-treatments. Specifically, the as fabricated material is subjected to a sub-transus heat-treatment followed by air-cooling and a super-transus heat-treatment followed by either air- or furnace-cooling. Next, a series of in-situ single edge notch tension (SENT) tests are carried out under a high-resolution digital optical microscope. The panoramic high-resolution images captured during the in-situ tests are then used to characterize the planar deformation on the specimen surface using microstructure-based digital image correlation (DIC). Additionally, the results of the in-situ SENT tests together with DIC and post-mortem fractographic analyses provided us with a better understanding of the microstructure-fracture correlations in these materials. Our results show that the fracture mechanism of the as fabricated and sub-transus heat-treated materials is essentially the same, while the changes in the microstructure following the super-transus heat-treatments significantly affects the fracture mechanism. In this case, several microcracks of hundreds of microns in length first nucleate away from the deformed notch following extreme plastic deformation at discrete locations. Furthermore, the location of these microcracks in the super-transus heat-treated materials is extremely sensitive to the details of the underlying microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A machine learning approach to fracture mechanics problems

Analytical and empirical solutions to engineering problems are usually preferred because of their convenience in applications. However, they are not always accessible in complex problems. A new class of solutions, based on machine learning (ML) models such as regression trees and neural networks (NNs), are proposed and their feasibility and value are demonstrated through the analysis of fracture toughness measurements. It is found that both solutions based on regression trees and NNs can provide accurate results for the specific problem, but NN-based solutions outperform regression-tree-based solutions in terms of their simplicity. Here this example demonstrates that ML solutions are a major improvement over analytical and empirical solutions in terms of both reliable functionality and rapid deployment. When analytical solutions are not available, the use of ML solutions can overcome the limitations of empirical solutions and substantially change the way that engineering problems are solved.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Role of Fluid and Temperature in Fracture Mechanics and Coupled THMC Processes for Enhanced Geothermal Systems

The ability to sustain high energy extraction efficiency from Enhanced Geothermal Systems (EGS) is affected by the ability to measure, characterize, and predict the effect of different perturbations that arise from fluid injection rates, fluid temperature, and shut-in conditions on existing and stimulated fracture systems throughout a subsurface reservoir’s lifecycle. The difficulty arises from limited knowledge of the interaction of fluid and temperature driven fractures with frictional interfaces that govern local deformation and frictional behavior in the surrounding rock. Thermo-poro-mechanical coupled processes tend to dominate this interaction and strongly affect the permeability and local stress distributions that impact efficiency and prevent optimal stimulation conditions over multi-decadal time frames.

Pyrak-Nolte, Laura [Purdue Univ., West Lafayette, ↗
DOE OSTI2023

Predicting encapsulant delamination in photovoltaic modules bridging photochemical reaction kinetics and fracture mechanics

Abstract Photovoltaic (PV) modules are subjected to environmental stressors (UV exposure, temperature, and humidity) that cause degradation within the encapsulant and its interfaces with adjacent glass and cell substrates. To save experimental time and to enable long‐term assessment with intensive degradation only taking place after many years, the development of predictive models is indispensable. Previous works have modeled the delamination of the ethylene vinyl acetate (EVA) encapsulant/glass and encapsulant/cell interfaces under field aging conditions with fundamental photochemical degradation reactions that lead to molecular scission and loss of interfacial adhesion, characterized by the fracture resistance, G c . However, these models were fundamentally limited in that the following aspects were not incorporated: (i) molecular crosslinking in the field, (ii) synergistic autocatalytic interactions of degradation mechanisms, (iii) connection between degraded encapsulant structure and its mechanical properties, and (iv) rigorous treatment of the plasticity contribution to G c with finite element models. Here, we present a time‐dependent multiscale model that addresses these limitations and is applicable to a wide range of encapsulants and interfaces. For the reference EVA encapsulant and its interfaces with the glass and cell, the presented model predicts an initial rise in G c in the first 3 years of field aging from crosslinking, then a subsequent sharp decline from degradation mechanisms. We used nanoindentation to measure the changes in EVA mechanical properties over exposure time to tune the model parameters. The model predictions of G c and mechanical properties match with experimental data and show an improvement compared to previous models. The model can even predict switches in failure interfaces, such as the observed EVA/cell to EVA/glass transition. We also conducted a sensitivity analysis study by varying the degradation and crosslinking kinetic parameters to demonstrate their effects on G c . Model extensions to polyolefin elastomer‐ and silicone‐encapsulants and their interfaces are also demonstrated.

Liu, Kuan↗
DOE OSTI2022

Stress-controlled fatigue of HfNbTaTiZr high-entropy alloy and associated deformation and fracture mechanisms

The stress-controlled fatigue tests are carried out at a stress ratio of 0.1 and a frequency of 10 Hz, and span both low-cycle and high-cycle regimes by varying the applied stress amplitudes. The high-cycle fatigue regime gives a fatigue strength of 497 MPa and a fatigue ratio of 0.44. At equivalent conditions, the alloy's fatigue strength is greater than all other high-entropy alloys (HEAs) with reported high-cycle fatigue data, dilute body-centered cubic alloys, and many structural alloys such as steels, titanium alloys, and aluminum alloys. Through in-depth analyses of crack-propagation trajectories, fracture-surface morphologies and deformation plasticity by means of various microstructural analysis techniques and theoretical frameworks, the alloy's remarkable fatigue resistance is attributed to delayed crack initiation in the high-cycle regime, which is achieved by retarding the formation of localized persistent slip bands, and its good resistance to crack propagation in the low-cycle regime, which is accomplished by intrinsic toughening backed up by extrinsic toughening. Additionally, the stochastic nature of the fatigue data is neatly captured with a 2-parameter Weibull model.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2020

Tensile testing and fracture mechanism analysis of polyvinyl alcohol nanofibrous webs

Abstract A tensile properties testing study was conducted to understand the influence of thickness, cross‐head speed (speed of testing), gauge length (GL; specimen test length), and sample shape on important tensile properties of polyvinyl alcohol (PVA) nanofiber webs. The effects of each testing parameter on load at break, extension at break, Young's modulus, and tensile stress–strain curve of PVA nanofiber webs are analyzed. The Welch two sample t ‐tests show the significant difference among tested data. Using interaction plots, two‐way analysis of variance, and margin mean plots, the interaction effects among testing parameters have been analyzed. Of all the factors, cross‐head speed, the interaction among GL, and sample thickness (GL: Thickness) and the interaction among GL, testing speed and sample thickness (GL: Speed: Thickness) have significant influence on the tensile properties of PVA nanofiber webs. Moreover, the hypothesized model of mechanism of tensile strain–stress curve of PVA nanofiber webs has been proposed. Based on the model, the tensile strain–stress curve can be split into three stages: linear elastic, partial break up, and complete breakage. This study will provide a better understanding of tensile testing parameters' effects and their interaction effects on the tensile properties of nanowebs.

Lou, Lihua↗
DOE OSTI2021

In-situ x-ray computed tomography analysis of fracture mechanisms in ultrasonic additively manufactured Al-6061 alloy

The deformation and failure mechanisms in an ultrasonic additively manufactured Al-6061 alloy are studied using in-situ x-ray computed tomography during tensile deformation as well as ex-situ characterization with scanning electron microscopy. The role of pre-existing voids between the build layers on the failure mechanism is discussed with a focus on individual foil failures and void coalescence.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental Evaluation of Deformation and Fracture Mechanisms in Highly Irradiated Austenitic Steels

The present report documents recent experimental results of analysis using scanning electron microscopy/electron backscatter diffraction (SEM-EBSD) of plastic deformation mechanisms and strain localization phenomena in austenitic steels irradiated by neutrons. Experiments were performed with specimens irradiated to 125 dpa and, additionally, with specimens that experienced radiation-induced swelling up to 3%. Section 1 briefly analyzes the deformation localization in irradiated steels and its consequences on the material performance. The section describes the advantages and importance of the SEM-EBSD approach combined with in situ mechanical testing capability. Section 2 briefly introduces the experimental tools and methods (i.e., SEM/EBSD in situ tensile frame, electric discharge machine to manufacture irradiated specimens) and describes the investigated materials (i.e., element composition, irradiation conditions, and general microstructure). Section 3 describes the key experimental results and provides a brief analysis and comparison with the datasets obtained earlier within the same task (i.e., low-dose specimens). The discussion focuses on EBSD microstructure maps with strain localization features, misorientation evolution as a function of strain, and observed deformation mechanisms. Section 4 evaluates data collected in recent years on highly irradiated steel and estimates the possible misorientation evolution under irradiation. The section introduces and discusses the concept of in-service-induced damage as an irradiation-assisted stress-corrosion cracking precursor. Section 5 summarizes the work performed. As expected, the present work results are beneficial for exploring and understanding degradation mechanisms in highly irradiated in-core materials found in light water reactors after long-term in-service life.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗