Search NASA⌕ Search

SEARCH · Search NASA

Results for “FUSELAGES - BENDING MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A 0.15-scale study of configuration effects on the aerodynamic interaction between main rotor and fuselage

Hover and forward flight tests were conducted to investigate the mutual aerodynamic interaction between the main motor and fuselage of a conventional helicopter configuration. A 0.15-scale Model 222 two-bladed teetering rotor was combined with a 0.15-scale model of the NASA Ames 40x80-foot wind tunnel 1500 horsepower test stand fairing. Configuration effects were studied by modifying the fairing to simulate a typical helicopter forebody. Separation distance between rotor and body were also investigated. Rotor and fuselage force and moment as well as pressure data are presented in graphical and tabular format. Data was taken over a range of thrust coefficients from 0.002 to 0.007. In forward flight speed ratio was varied from 0.1 to 0.3 with shaft angle varying from +4 to -12 deg. The data show that the rotors effect on the fuselage may be considerably more important to total aircraft performance than the effect of the fuselage on the rotor.

Trept, Ted↗
NASA NTRS1996

Comparison of Hover/Ground-Effect Characteristics for a Joint Strike Fighter Configuration

Hover and ground-effect tests were conducted with the Lockheed-Martin Large Scale Powered Model (LSPM) during June-November 1995 at the NASA Ames Research Center's Outdoor Aerodynamics Research Facility (OARF). This was done in support of the Joint Strike Fighter (JSF) Program being lead by the Department of Defense. The program was previously metered to as the Joint Advanced Strike Technology (JAST) Program. The tests at the OARF included: engine thrust calibrations out of ground effect, measurements of individual nozzle jet pressure decay characteristics, and jet-induced hover force and moment measurements in and out of ground effect. The engine calibrations provide data correlating propulsion system throttle and nozzle settings to thrust forces and moments for the bare fuselage with the wings, canards, and tails removed. This provides propulsive forces and moments while minimizing any of the effects due to the presence of the airframe. The engine calibrations were used later to determine thrust for hover testing at the OARF and for transition testing which took place in the NASA Ames 80 by 120 foot Wind Tunnel. The jet decay characteristics reflect the jet entrainment properties and are related to the aircraft suckdown characteristics. The JSF program provided the opportunity to obtain model scale effects using two models; one at small scale and one at large scale. Examples of data from these tests will be presented out of ground effect which will demonstrate the effect of scale. For one JSF configuration, two small-scale models and one large-scale model were tested and obtained different values for the lift loss out of ground effect. These differences were examined and are found to be largely dependent on the jet efflux characteristics. The jet-induced hover forces and moments are presented in and out of ground effect. For the hover testing the model is methodically built up from the bare fuselage, to include the wings, canards, and vertical tails, to determine the effects of each. Other components such as weapons bay doors, landing gear doors, and other lift improvement devices and their effect on the jet-induced forces and moments are examined.

Hange, Craig↗
NASA NTRS1975

Wind tunnel investigation of helicopter-rotor wake effects on three helicopter fuselage models

The effects of rotor wake on helicopter fuselage aerodynamic characteristics were investigated in the Langley V/STOL tunnel. Force, moment, and pressure data were obtained on three fuselage models at various combinations of windspeed, sideslip angle, and pitch angle. The data show that the influence of rotor wake on the helicopter fuselage yawing moment imposes a significant additional thrust requirement on the tail rotor of a single-rotor helicopter at high sideslip angles.

Wilson, J. C.↗
NASA NTRS1979

The effects of configuration changes on spin and recovery characteristics of a low-wing general aviation research airplane

A fully instrumented, low-wing, single-engine general aviation airplane has been spin tested. Several tail configurations, wing leading-edge modifications, fuselage modifications, moment-of-inertia variations, center-of-gravity positions, and control inputs have been tested to determine their effect on spinning and spin recovery. Results indicate that wing airfoil design can significantly influence airplane spin and recovery characteristics and can overpower the effects of tail design. Results also point out a need to determine limitations of such factors as Reynolds number in model spin test techniques and high angle-of-attack aerodynamics.

Stough, H. P., III↗
NASA NTRS1992

Vortical flow control on a wing-body combination using tangential blowing

The objective of the experimental program reported here was to evaluate the possibility of using tangential blowing to create roll and yaw control on a delta wing-forebody combination at high angles of attack. It is found that the vortical flow over the model can be manipulated more efficiently by blowing on the nose section rather than fuselage. Large rolling moments and side forces are generated by blowing from forebody compared to wing blowing. For a wing-body combination, a model with a blunt nose is found to be less sensitive to flow asymmetry than a sharp-nosed configuration. Rolling moment changes sign from prestall to stall for all the configurations tested.

Celik, Zeki Z.↗
NASA NTRS1932

Pressure Distribution Over the Fuselage of a PW-9 Pursuit Airplane in Flight

This report presents the results obtained from pressure distribution tests on the fuselage of a PW-9 pursuit airplane in a number of conditions of flight. The investigation was made to determine the contribution of the fuselage to the total lift in conditions considered critical for the wing structure, and also to determine whether the fuselage loads acting simultaneously with the maximum tail loads were of such a character as to be of concern with respect to the structural design of other parts of the airplane. The results show that the contribution of the fuselage toward the total lift is small on this airplane. Aerodynamic loads on the fuselage are, in general, unimportant from the structural viewpoint, and in most cases they are of such character that, if neglected, a conservative design results. In spins, aerodynamic forces on the fuselage produce diving moments of appreciable magnitude and yawing moments of small magnitude, but opposing the rotation of the airplane. A table of cowling pressures for various maneuvers is included in the report.

Rhode, Richard V↗
NASA NTRS2005

NASA Structural Analysis Report on the American Airlines Flight 587 Accident - Local Analysis of the Right Rear Lug

A detailed finite element analysis of the right rear lug of the American Airlines Flight 587 - Airbus A300-600R was performed as part of the National Transportation Safety Board s failure investigation of the accident that occurred on November 12, 2001. The loads experienced by the right rear lug are evaluated using global models of the vertical tail, local models near the right rear lug, and a global-local analysis procedure. The right rear lug was analyzed using two modeling approaches. In the first approach, solid-shell type modeling is used, and in the second approach, layered-shell type modeling is used. The solid-shell and the layered-shell modeling approaches were used in progressive failure analyses (PFA) to determine the load, mode, and location of failure in the right rear lug under loading representative of an Airbus certification test conducted in 1985 (the 1985-certification test). Both analyses were in excellent agreement with each other on the predicted failure loads, failure mode, and location of failure. The solid-shell type modeling was then used to analyze both a subcomponent test conducted by Airbus in 2003 (the 2003-subcomponent test) and the accident condition. Excellent agreement was observed between the analyses and the observed failures in both cases. From the analyses conducted and presented in this paper, the following conclusions were drawn. The moment, Mx (moment about the fuselage longitudinal axis), has significant effect on the failure load of the lugs. Higher absolute values of Mx give lower failure loads. The predicted load, mode, and location of the failure of the 1985-certification test, 2003-subcomponent test, and the accident condition are in very good agreement. This agreement suggests that the 1985-certification and 2003- subcomponent tests represent the accident condition accurately. The failure mode of the right rear lug for the 1985-certification test, 2003-subcomponent test, and the accident load case is identified as a cleavage-type failure. For the accident case, the predicted failure load for the right rear lug from the PFA is greater than 1.98 times the limit load of the lugs. I.

Raju, Ivatury S↗
NASA NTRS2006

Structural Analysis of the Right Rear Lug of American Airlines Flight 587

A detailed finite element analysis of the right rear lug of the American Airlines Flight 587 - Airbus A300-600R was performed as part of the National Transportation Safety Board s failure investigation of the accident that occurred on November 12, 2001. The loads experienced by the right rear lug are evaluated using global models of the vertical tail, local models near the right rear lug, and a global-local analysis procedure. The right rear lug was analyzed using two modeling approaches. In the first approach, solid-shell type modeling is used, and in the second approach, layered-shell type modeling is used. The solid-shell and the layered-shell modeling approaches were used in progressive failure analyses (PFA) to determine the load, mode, and location of failure in the right rear lug under loading representative of an Airbus certification test conducted in 1985 (the 1985-certification test). Both analyses were in excellent agreement with each other on the predicted failure loads, failure mode, and location of failure. The solid-shell type modeling was then used to analyze both a subcomponent test conducted by Airbus in 2003 (the 2003-subcomponent test) and the accident condition. Excellent agreement was observed between the analyses and the observed failures in both cases. The moment, Mx (moment about the fuselage longitudinal axis), has significant effect on the failure load of the lugs. Higher absolute values of Mx give lower failure loads. The predicted load, mode, and location of the failure of the 1985- certification test, 2003-subcomponent test, and the accident condition are in very good agreement. This agreement suggests that the 1985-certification and 2003-subcomponent tests represent the accident condition accurately. The failure mode of the right rear lug for the 1985-certification test, 2003-subcomponent test, and the accident load case is identified as a cleavage-type failure. For the accident case, the predicted failure load for the right rear lug from the PFA is greater than 1.98 times the limit load of the lugs.

Raju, Ivatury S.↗
NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗
NASA NTRS1995

Analysis of Tangential Slot Blowing on F/A-18 Isolated Forebody

The generation of significant side forces and yawing moments on an F/A-18 fuselage through tangential slot blowing is analyzed using computational fluid dynamics. The effects of freestream Mach number, jet exit conditions, jet length, and jet location are studied. The effects of over- and underblowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side forces, yawing moments, and surface pressure distributions generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. Comparison with available experimental data from full-scale wind-tunnel and subscale wind-tunnel tests are made. This computational analysis complements the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flowfield about the isolated F/A-18 forebody. Additionally, it extends the slot-blowing database to transonic maneuvering Mach numbers.

Gee, Ken↗
NASA NTRS1994

Analysis of tangential slot blowing on F/A-18 isolated forebody

Generation of significant side forces and yawing moments on an F/A-18 fuselage through tangential slot blowing is analyzed using computational fluid dynamics. The effects of freestream Mach number, jet exit conditions, jet length, and jet location are studied. The effects of over- and under-blowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side forces, yawing moments, and surface pressure distributions generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. Comparison with available experimental data from full-scale wind tunnel and sub-scale wind tunnel tests are made. This computational analysis complements the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about the isolated F/A-18 forebody. Additionally, it extends the slot-blowing database to transonic maneuvering Mach numbers.

Gee, K.↗
NASA NTRS1959

Investigation of the Stability of Very Flat Spins and Analysis of Effects of Applying various Moments Utilizing the Three Moment Equations of Motion

Based on linearized equations of motion utilizing only the three moment equations and assuming only flat-spin conditions, it appears that contemporary designs (with the moment of inertia about the wing axis I(sub Y) considerably greater than the moment of inertia about the fuselage axis I(sub X) having positive values of C(sub l, sub p) (rolling-moment coefficient due to rolling) or positive values of C(sub l, sub beta) (rolling-moment coefficient due to sideslip) will probably not have a stable spin in the flat-spin region near an angle of attack of 90 deg. If the damping in pitch in flat-spin attitudes is zero, stable flat-spin conditions may not be possible on an airplane having the mass primarily distributed along the wings. The effect of moving ailerons with the spin or the effect of applying a positive pitching moment producing recovery for contemporary fighter designs will be greatest for large negative values of C(sub n, sub beta) (yawing-moment coefficient due to sideslip). In addition, for a certain critical value of positive C(sub n, sub beta), the rolling moment applied by moving ailerons with the spin or the application of a positive pitching moment will have no effect on reducing the spin rate.

Klinar, Walter J.↗
NASA NTRS1983

Interference effects of aft reaction-control yaw jets on the aerodynamic characteristics of a space shuttle orbiter model at supersonic speeds

A wind tunnel investigation of the interference effects of aft reaction control system yaw jet plumes on a 0.0125 scale Space Shuttle orbiter model was conducted at Mach numbers from 2.50 to 4.50. Test variables included model angle of attack, model angle of sideslip, jet to free stream mass flow ratio, and number and position of operating jets. The aft reaction control jet plume creates a blockage above and behind the wing on the side in which the jet exhausts and results in flow separation on the wing upper surface and fuselage side. Positive pitching moment and side force increments and negative yawing moment and rolling moment increments due to the flow separations are incurred for left side firing jets, primarily at angles of attack above 10 deg. The yawing moment interference increments are favorable and result in a small jet thrust amplification. As a result of this investigation, the aft reaction control system was certified for operation at supersonic Mach numbers prior to the first flight of the space transportation system (STS-1).

Covell, P. F.↗
NASA NTRS1984

A mathematical model of the UH-60 helicopter

This report documents the revisions made to a ten-degree-of-freedom, full-flight envelope, generic helicopter mathematical model to represent the UH-60 helicopter accurately. The major modifications to the model include fuselage aerodynamic force and moment equations specific to the UH-60, a canted tail rotor, a horizontal stabilator with variable incidence, and a pitch bias actuator (PBA). In addition, this report presents a full set of parameters and numerical values which describe the helicopter configuration and physical characteristics. Model validation was accomplished by comparison of trim and stability derivative data generated from the UH-60 math model with data generated from a similar total force and moment math model.

Hilbert, K. B.↗
NASA NTRS1989

Rotor blade dynamic design

The rotor dynamic design considerations are essentially limitations on the vibratory response of the blades which in turn limit the dynamic excitation of the fuselage by forces and moments transmitted to the hub. Quantities which are associated with the blade response and which are subject to design constraints are discussed. These include blade frequencies, vertical and inplane hub shear, rolling and pitching moments, and aeroelastic stability margin.

Pritchard, Jocelyn I.↗
NASA NTRS1954

Experiments on a Tail-wheel Shimmy

Model tests on the "running belt" and tests with a full-scale tail wheel were made on a rotating drum as well as on a runway in order to investigate the causes of the undesirable shimmy phenomena frequently occurring on airplane tail wheels, and the means of avoiding them. The small model (scale 1:10) permitted simulation of the mass, moments of inertia, and fuselage stiffness of the airplane and determination of their influence on the shimmy, whereas by means of the larger model with pneumatic tires (scale 1:2) more accurate investigations were made on the tail wheel itself. The results of drum and road tests show good agreement with one another and with model values. Detailed investigations were made regarding the dependence of the shimmy tendency on trail, rolling speed, load, size of tires, ground friction,and inclination of the swivel axis; furthermore, regarding the influence of devices with restoring effect on the tail wheel, and the friction damping required for prevention of shimmy. Finally observations from slow-motion pictures are reported and conclusions drawn concerning the influence of tire deformation.

WHEEL, TAIL - SHIMMYING↗