Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gelation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Temperature-Dependent Molecular Diffusional Properties in Deep Eutectic Solvents and Eutectogels

Eutectogels (ETGs) prepared from deep eutectic solvents (DESs), a gelator, and water have many uses in separations, catalysis, and energy storage systems. In these applications, temperature-dependent molecular diffusional properties and intermolecular interactions play a critical role in their function. Diffusional properties of Alexa Fluor 633 and ATTO 647N were measured across a range of temperatures in choline chloride:2glycerol DESs comprised of one molar equivalent of choline chloride and two molar equivalents of glycerol (also known as glyceline) as well as ETGs made from this DES, a xanthan gum gelator, and 10% w/w water or 20% w/w water. Fluorescence recovery after photobleaching (FRAP) was employed to evaluate potential changes in molecular diffusion within DESs and ETGs from 20 to 100 °C. Surprisingly, the ETGs have a larger sample viscosity but also exhibit faster molecular diffusion when compared to the dry DES. This is attributed to macroscopic properties of the ETGs (e.g., pores, three-dimensional structure). The FRAP data also show an irreversible temperature-dependent decrease in the diffusion coefficient of both fluorophores in the ETGs. This is consistent with differential scanning calorimetry data of the ETG, which shows a shift to a more negative glass transition temperature (−36 °C to −47 °C) after the first cooling/heating cycle. Raman data reveal no detectable changes in the intermolecular interactions in either the DESs or ETGs as a function of temperature or water content. Finally, the findings on temperature- and water-dependent diffusional properties of DESs and ETGs provide a foundation for optimizing the use of these materials across various applications, particularly where repeated heating/cooling cycles may be used.

alcohols↗
DOE OSTI2024

Aluminosilicate colloidal gels: from the early age to the precipitation of zeolites

Aluminosilicate hydrogels are often considered to be precursors for the crystallisation of zeolites carried out under hydrothermal conditions. The preparation of mechanically homogeneous aluminosilicate gels enables the study of these materials through bulk rheology and observation of the aging dynamics until the precipitation of crystalline zeolites. The first part of this study deals with the establishment of ternary state diagrams, in order to identify the range of chemical formulations that enable preparation of single-phase homogeneous gels. Then, by studying the viscoelastic moduli during the gelation reaction, and by yielding the gel under large deformation, we propose an empirical law considering the partial order of reaction on each chemical element, to predict the gelation time according to the chemical formulation. The scaling behavior of the elastic properties of this colloidal gel shows a transition from a strong link behavior to a weak link regime. Long term aging results in the shrinkage of the gel, accompanied by syneresis of interstitial liquid at the surface. Zeolites precipitate through crystallisation by a particle attachment mechanism, when thermodynamic equilibrium is reached. The stoichiometry of the precipitated zeolites is not only consistent with the concentration of the remaining species in the supernatant but, surprisingly, it is also very close to the partial order of the reaction of the chemical elements involved in the determination of the critical gel point. This indicates a strong correlation between the morphology of the soft amorphous gel network that is formed at an early age and those of the final solid precipitated crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Rapid curing dynamics of PEG-thiol-ene resins allow facile 3D bioprinting and in-air cell-laden microgel fabrication

Thiol-norbornene photoclick hydrogels are highly efficient in tissue engineering applications due to their fast gelation, cytocompatibility, and tunability. In this work, we utilized the advantageous features of polyethylene glycol (PEG)-thiol-ene resins to enable fabrication of complex and heterogeneous tissue scaffolds using 3D bioprinting and in-air drop encapsulation techniques. We demonstrated that photoclickable PEG-thiol-ene resins could be tuned by varying the ratio of PEG-dithiol to PEG norbornene to generate a wide range of mechanical stiffness (0.5–12 kPa) and swelling ratios. Importantly, all formulations maintained a constant, rapid gelation time (<0.5 s). We used this resin in biological projection microstereolithography (BioPµSL) to print complex structures with geometric fidelity and demonstrated biocompatibility by printing cell-laden microgrids. Moreover, the rapid gelling kinetics of this resin permitted high-throughput fabrication of tunable, cell-laden microgels in air using a biological in-air drop encapsulation apparatus (BioIDEA). We demonstrated that these microgels could support cell viability and be assembled into a gradient structure. This PEG-thiol-ene resin, along with BioPµSL and BioIDEA technology, will allow rapid fabrication of complex and heterogeneous tissues that mimic native tissues with cellular and mechanical gradients. The engineered tissue scaffolds with a controlled microscale porosity could be utilized in applications including gradient tissue engineering, biosensing, and in vitro tissue models.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Universal progression of structure and dynamics in colloidal nanocrystal gels during salt-accelerated aging

Controlling the structure and function of colloidal gels requires a detailed understanding of how the various components govern network formation and aging. In particular, molecular additives like salts are widely used to tune interparticle interactions, yet their influence on gelation pathways in complex systems such as colloidal nanocrystal gels remains inadequately understood. Here, we investigate how noncoordinating salts modulate the evolution of gels formed using chemically linked tin-doped indium oxide nanocrystals. Through combined structural, dynamic, and kinetic analyses, we demonstrate that increasing salt concentration accelerates gelation. When rescaled by salt-dependent characteristic times, the evolution collapses onto universal trajectories, revealing a time-salt superposition principle. The universality extends across length scales, suggesting a consistent salt-dependent mechanism that controls both local structuring and macroscopic network formation. This observed salt modulation of structure and dynamics provides a predictive basis for controlling the kinetics of nonequilibrium nanocrystal gel assembly, enhancing the rational design of functional nanomaterials with tunable properties.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Irradiation of linear polyethylene - Partitioning between sol and gel.

Molecular weight fractions of linear polyethylene were irradiated at 133 C, in the completely molten and highly crystalline states, for the purpose of assessing the importance of chain-scission processes and establishing the critical conditions for gelation. The partitioning between sol and gel in either state was found to adhere to the theory for the intermolecular cross-linking of monodisperse species for dosages just beyond the gel point. Deviations from theory occurred as the dosage was increased further. It was concluded that main-chain scission, at these temperatures, is not a significant process. High molecular weight samples in the completely molten state obeyed the Flory-Stockmayer condition for critical gelation.

Rijke, A. M.↗
NASA NTRS1989

Chemoviscosity modeling for thermosetting resin systems, 4

An experimental study on the changes of chemorheological properties has been conducted and analyzed on commercial Hercules 3501-6 resin system cured under several isothermal conditions between 375 and 435 K. For the cure temperatures equal to or greater than 385 K, the storage modulus curing curves, G prime (t), exhibited abrupt changes in slope which occurred at various times depending on the curing temperatures and were attributed to the onset of gelation reactions. The crossover points between G prime (t) and G double prime (t) curves were observed for curing temperatures equal to or greater than 400 K. The gelation and the crossover points obtained from the chemorheological measurements, therefore, defined two characteristic resin states during cure. Approximately the same value for the degree of cure was reached by the advancement of the reaction at each of these states. The temperature dependency of the viscosities for the characteristic resin states and the rate constants of increase in moduli at different stages of curing were analyzed. Various G prime (t) and G double prime (t) isothermal curing curves were also shown to be capable of being superimposed on one another by the principle of time-temperature superposition. The resultant shift factors a sub t(t) and a Eta(T) were shown to follow the Arrhenius type relationship. Values of the activation energy suggested that the reaction kinetics, instead of the diffusion mechanism, was the limiting step in the overall resin advancement for the cure at temperatures equal to or greater than 385 K.

Hou, T. H.↗
NASA NTRS1997

Surface Plasmon Resonance Evaluation of Colloidal Metal Aerogel Filters

Surface plasmon resonance imaging has in the past been applied to the characterization of thin films. In this study we apply the surface plasmon technique not to determine macroscopic spatial variations but rather to determine average microscopic information. Specifically, we deduce the dielectric properties of the surrounding gel matrix and information concerning the dynamics of the gelation process from the visible absorption characteristics of colloidal metal nanoparticles contained in aerogel pores. We have fabricated aerogels containing gold and silver nanoparticles. Because the dielectric constant of the metal particles is linked to that of the host matrix at the surface plasmon resonance, any change 'in the dielectric constant of the material surrounding the metal nanoparticles results in a shift in the surface plasmon wavelength. During gelation the surface plasmon resonance shifts to the red as the average or effective dielectric constant of the matrix increases. Conversely, formation of an aerogel or xerogel through supercritical extraction or evaporation of the solvent produces a blue shift in the resonance indicating a decrease in the dielectric constant of the matrix. From the magnitude of this shift we deduce the average fraction of air and of silica in contact with the metal particles. The surface area of metal available for catalytic gas reaction may thus be determined.

Smith, David D.↗
NASA NTRS2002

PCS: The First Fluid Physics Payload on ISS

The Physics of Colloids in Space (PCS) experiment was accommodated within International Space Station (ISS) EXpedite the PRocessing of Experiments to Space Station (EXPRESS) Rack 2 and was remotely operated from early June 2001 until February 2002 from NASA Glenn Research Center's Telescience Support Center in Cleveland, Ohio and from a remote site at Harvard University in Cambridge, Massachusetts. PCS is an experiment conceived by Professor David A. Weitz of Harvard University (the Principal Investigator), focusing on the behavior of three different classes of colloid mixtures. The sophisticated light scattering instrumentation comprising PCS is capable of color imaging, and dynamic and static light scattering from 11 to 169 degrees, Bragg scattering over the range from 10 to 60 degrees, and laser light scattering at low angles from 0.3 to 6.0 degrees. The PCS instrumentation performed remarkably well, demonstrating a flexibility that enabled experiments to be performed that had not been envisioned prior to launch. While on-orbit, PCS accomplished 2400 hours of science operations, and was declared a resounding success. Each of the eight sample cells worked well and produced interesting and important results. Crystal nucleation and growth and the resulting structures of two binary colloidal crystal alloys were studied, with the long duration microgravity environment of the ISS facilitating extended studies on the growth and coarsening characteristics of the crystals. In another experiment run, the de-mixing of the colloid-polymer critical-point sample was studied as it phase-separates into two phases, one that resembles a gas and one that resembles a liquid. This process was studied over four decades of length scale, from 1 micron to 1 centimeter, behavior that cannot be observed in this sample on Earth because sedimentation would cause the colloids to fall to the bottom of the cell faster than the de-mixing process could occur. Similarly, the study of gelation and aging of another colloid-polymer sample, the colloid-polymer gel, also provided valuable information on gelation mechanisms, as did investigations on the extremely the low concentration silica and polystyrene fractal gel samples.

Doherty, M.↗
NASA NTRS2002

Isocyanate Cross-Linked Silica: Structurally Strong Aerogels

Molecular-level synergism between the silica nanoparticles of pre-formed monoliths and molecular cross-linkers inverts the relative host-guest roles in glass-polymer composites, leading to new strong low-density materials. Attempts to load gels with variable amounts of polyurethane precursors such as di-ISO and diol end-capped polybutylene adipate followed by heat treatment, washing, and supercritical drying led to opaque materials, somewhat stronger than silica but still quite brittle and much inferior to the materials described above. Direct mixing of a diisocyanate and an alcohol-free sol has been attempted recently by Yim et al. Reportedly, that procedure leads to week-long gelation times and requires an at least equally long aging period. In our attempt to add various amounts of di-ISO in a base-catalyzed sol in PC, we also noticed a week-long gelation time. The resulting aerogels were translucent but no less brittle than native silica. According to more recent studies, if propylene carbonate is replaced with acetone, it leads not only to shorter processing times, but also to much stronger gels that can tolerate loads in excess of 40 kg in the arrangement presented. We attribute that behavior to the lower viscosity of acetone, that allows faster diffusion of the di-ISO solution within the pores before di-ISO has time to react with the surface of silica. Further studies are underway to vary the chemical identity of the diisocyanate, as well as the composition and density of silica.

Leventis, Nicholas↗
NASA NTRS2014

Synthesis and Properties of Cross-Linked Polyamide Aerogels

We report our ongoing research on polyamide aerogels made by step growth polymerization using a combination of terephthaloyl chloride, isophthaloyl chloride and m-phenylenediamine. Crosslinking of the amine capped polymer chains with 1,3,5-benzenetricarbonyl trichloride causes gelation in as little as two to five minutes. Removing the reaction solvent is accomplished through solvent exchange, followed by drying using supercritical CO2 extraction to give colorless aerogels with densities ranging from 0.07 to 0.33 grams per cubic centimeter and surface areas as high as 440 square meters per gram. Statistical experimental design methodology has been utilized to investigate dependence of properties of these aerogels, such as density, compressive modulus, and surface area, on changes in fabrication parameters including formulated number of amide oligomer repeat units (n-value), acid chloride (meta, para or combination), and solids concentration of solution used for gelation. For example, the density of these materials was found to be dependent on the acid chloride type and the solids concentration, but n was not a significant variable. However, surface area was significantly influenced by all three parameters. The polyamide aerogels represent a potential cost savings over previously reported polyimide aerogels, since monomers are all inexpensive and commercially available. Surface area and density were both highest when 100 terephthaloyl chloride was used but a combination of 5 solid concentration, 100 terephthaloyl chloride and n of 20 gave the best combination of properties.

cross-linked↗
DOE OSTI2025

Establishing a silica gel zone in well annulus and evaluating its performance in blocking vertical water flow

Wells are often constructed for monitoring purposes with relatively long screen lengths (e.g., >10 m). Vertical water flows can occur within the artificial or natural filterpack annulus that surrounds the screened interval, bypassing packer assemblies installed inside the wellbore. Attempts to isolate discrete vertical zones during groundwater sampling are unsuccessful when annular flow occurs and lead to remedy decisions based on biased or incorrect interpretations. Blocking vertical annular water flow and contaminant transport will help obtain more accurate concentrations of contaminants from sampling in targeted depth intervals. The application of silica gels formed from the injected colloidal silica CS suspensions is a novel approach to minimize or prevent movement of vertical movement of groundwater in the surrounding filterpack annulus. In this work, we tested the feasibility of injecting CS suspensions to target locations and developed a modified CS formulation that is injectable and prevents gravity sinking. We studied the distribution and penetration of silica gel at laboratory scale in mock well annulus with surrounding formations. We evaluated the performance of the silica gel in blocking vertical water flow in the annulus and in minimizing chemical transport through the gel zone. CS suspension formulations have been defined that are ready for injection, stay in target locations, and form gel within desired time frames. Injection of CS suspensions achieved uniform distribution in a well annulus filter pack, fully occupied the annulus pore space, and penetrated the formation surrounding the filter packer with a sufficient distance to create a hydraulic annular seal when the injection was applied at a sufficient rate. The depth of penetration into the formation was dependent on the permeability contrast between the filter pack and the surrounding formation. Silica gel that formed in the annulus blocked vertical water flow and stopped the chemical transport through the gel zone. In conclusion, this research reveals that using CS suspension injection and sequential gelation (CS-GEL) is a promising technology for blocking vertical water flow and chemical transport through the filter pack in targeted zones within the annulus of long-screened well systems.

Colloidal silica suspension↗
DOE OSTI2024

Determining the Reaction Kinetics and Thermodynamics of a Diels–Alder Network Using Dynamic Gel Criteria

We undertook a detailed rheological investigation to evaluate the kinetic parameters of the forward and reverse Diels–Alder (DA) reactions of a model network cross-linked using a furan prepolymer and a common aromatic bismaleimide. At high temperature where the Winter–Chambon’s criterion of frequency-independence was more applicable, a multiwave technique permitted van’t Hoff analysis and calculation of the reaction thermodynamic parameters, specifically the enthalpy and entropy of the reaction: ΔH° = –38.3 ± 5.2 kJ mol –1 and ΔS° = –94.3 ± 13.4 J mol –1 . At mild temperatures where the G'–G" crossover point is experimentally convenient to measure gelation, isothermal tests were used to obtain reasonable fDA kinetic parameters from Eyring analysis such as the apparent activation enthalpy and entropy of ΔH$^{‡}_{fDA}$ = 76.8 ± 6.9 kJ mol –1 and ΔS$^{‡}_{fDA}$= –82.8 ± 22.2 J mol –1 K –1 . Comparable rheokinetic methods include cross-linking density measurements and stress relaxation tests to calculate effective kinetics, whereas the critical gel conversion was consistently applied here. As a result, rate data are fitted with the Arrhenius equation for comparison purposes and the Eyring equation to demonstrate its broader utility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Tuning the Mechanical Properties of Crosslinked Copolymers via Sequence and Solvent‐Selective Swelling for Vat Photopolymerization

Block copolymers (BCPs) offer distinct advantages for vat photopolymerization by enabling mechanically programmable network structures through microphase-separated morphologies that can be kinetically trapped during curing, yielding properties unattainable in homogeneous resins. However, the respective roles of repeat-unit sequence and solvent environment, together with their interplay in directing network formation and mechanical performance, remain unclear. Here, we synthesize a series of CO 2 -based polycarbonate copolymers comprising a crosslinkable glassy poly(vinyl cyclohexene carbonate) (PVCHC, A block) and a non-crosslinkable soft poly(propylene carbonate) (PPC, B block). The polymer sequence is systematically varied (ABA, BAB, and statistical), and solvent choice controls block-selective swelling to jointly control gelation behavior, microphase morphology, and mechanical response through changes in the accessibility and local environment of photocrosslinkable vinyl groups during network formation, as revealed by photorheology and small angle x-ray scattering. By tuning polymer sequence and curing solvent, we transform nominally identical formulations from brittle to highly ductile materials, achieving a three-orders-of-magnitude range in toughness (0.003 to 9.1 MJ m −3 ). These results establish clear structure–processing–property relationships and identify polymer sequence and selective solvation as powerful strategies for programming both printability and performance of block copolymer resins for additive manufacturing.

additive manufacturing↗
DOE OSTI2025

The Triple Catalytic Action of Tertiary Nitrogen Catalysts in Recyclable Epoxy-Anhydride Thermosets

The thermosetting polymer matrix in fiber reinforced composites is an important component for energy related applications, such as the lightweighting of vehicles or their use in wind and waterpower turbine blades, due to their ability to provide superior adhesion, stiffness, and applicability to a wide range of manufacturing processes. Despite these benefits, today's thermosets are widely considered to be unrecyclable; thus, there is a large interest in redesigning these materials to be inherently recyclable so that energy intensive production of fibers and monomers can be circumvented, bolstering composite manufacture supply chains. Polyester covalent adaptable networks (PECANs) are one such promising alternative to the incumbent, nonrecyclable epoxy-amine thermosets. PECANs can be formed from the ring-opening co-polymerization (ROCOP) of epoxy-anhydride monomer mixtures and subsequent curing at mild temperatures to exhibit similar performance to conventional epoxies while also possessing unique dynamic chemistries along the ester-hydroxyl backbone that are capable of transesterification and thus reprocessability. While significant advancements have been made in formulating these materials for improved mechanical properties or optimizing solvolysis and reprocessing strategies, less attention has been placed on the impact of the residing amine catalyst used to generate the polyester network. In this work, we evaluated the triple-catalytic efficacy of 12 tertiary amines that act as a curing (bulk ROCOP), a transesterification (internal bond exchange), and a deconstruction (methanolysis) catalyst for PECAN thermosets. Specifically, we first distinguish between chain-growth and step-growth polymerization mechanisms for epoxy-amine and epoxy-anhydride mechanisms. We also utilized density functional theory (DFT) to estimate the basicity (pKb) of each catalyst. Of the tested catalysts, the ROCOP of the studied PECAN network can be completed between 95 and 247 min (at 80 degrees C), with variable gelation phenomena. Additionally, the stress relaxation (transesterification metric) efficiency of the tested PECAN networks with alternative embedded catalysts ranged from 95% to 15% reduction in stress after 5 h at 200 degrees C, and the depolymerization efficacy ranged from 2.5% to 9.8% deconstruction after 36 h at 130 degrees C. Overall, the nitrogen-based moieties were demonstrated to influence polymerization kinetics, catalyze the dynamic transesterification exchange mechanism, and aid in the solvolysis of the thermosets at end-of-life.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Autonomous Changes in Polymer Materials Driven by Chemical Fuels

Time-dependent properties in polymer materials can be achieved through coupling to out-of-equilibrium chemical fuel reactions that mimic biological processes. Through transient changes in bonding in polymers, transient gelation, changes in mechanical stiffness, swelling, self-healing, or self-assembly can be achieved. Recent advances in these categories are discussed. These out-of-equilibrium behaviors enable applications ranging from smart adhesives to actuators for soft robotics. However, challenges remain, including waste accumulation, bio-compatibility, and achieving functionally useful performance. Addressing these issues is essential for advancing the practical use of chemically driven polymer materials and unlocking their full potential for future technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Structure Development in Cross-Linked, Soybean Oil-based Waterborne Polyurethanes

Development of waterborne polyurethanes (WPU) using bio-based sources represents a step towards sustainable materials science and industry. We synthesized bio-based cationic water-dispersed crosslinked polyurethanes from high oleic soybean oil (HOSO) polyol, isophorone diisocyanate, and methyldiethanol amine, with varying ionic group contents after neutralization with acetic acid. Our primary objective was to analyze how crosslinking affects the dispersion process and film properties in multifunctional systems. The synthesis-structure-property relationship is elucidated through comprehensive analyses of the products at different stages of the synthesis. The dispersion of the WPU particles in water must occur prior to gelation during the final preparation, leading to incomplete conversion and the formation of imperfect networks. Insight into the synthesis process and polymer structure was gained by simulating polymer network parameters. Morphological analyses using synchrotron-based X-ray scattering and atomic force microscopy revealed a hierarchical structure within the WPU films. Importantly, all the films prepared in this study, without using coalescence agents, have low water absorption and high water contact angles, demonstrating their potential for textile and leather coatings and other applications.

bio-based polymers↗
DOE OSTI2024

Hydrocarboxylation of C=C Bonds in Polycyclooctene: Progress Toward Valorization of Waste Polyolefins

Upcycling of waste polyolefins into higher-value functional polymers through chemical functionalization is a promising strategy to recover value and minimize their environmental impact. We report the hydrocarboxylation of polycyclooctene as a model for accessing ethylene acrylic acid copolymers (EAA) from waste polyethylene. The effects of various process parameters on the hydrocarboxylation were investigated. The relationship between carboxylic acid concentration and material properties, including crystallinity, melting temperature, glass transition temperature, adhesive properties, and wettability, was studied in comparison to an unfunctionalized polyethylene. Among the catalysts evaluated, Co 2 (CO) 8 exhibited relatively slow kinetics toward the hydrocarboxylation and was not compatible with 2,6-di-tert-butyl hydroxytoluene, a common additive present in commercial polyolefins. PdCl 2 (PPh 3 ) 2 exhibited a higher reactivity toward the hydrocarboxylation, though polymer gelation was observed with extended reaction times or high catalyst loadings. Carboxylic acid incorporation into the polymer was readily controlled by varying the reaction time. Altogether, the resultant COOH-functionalized polyolefins possessed properties analogous to commercial EAA.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Biopolymer-supramolecular polymer hybrids for photocatalytic hydrogen production

Solar generation of H 2 is a promising strategy for dense energy storage. Supramolecular polymers composed of chromophore amphiphile monomers containing perylene monoimide (PMI) have been reported as crystalline light-harvesting assemblies for aqueous H 2 -evolving catalysts. Gelation of these supramolecular polymers with multivalent ions creates hydrogels with high diffusivity but insufficient mechanical stability and catalyst retention for reusability. We report here on using sodium alginate (SA) biopolymer to both induce supramolecular polymerization of PMI and co-immobilize them with catalysts in a robust hydrogel with high diffusivity that can also be 3D-printed. Faster mass transfer was achieved by controlling the material macrostructure by reducing gel diameter and microstructure by reducing biopolymer loading. Optimized gels produce H 2 at rates rivaling solution-based PMI and generate H 2 for up to 6 days. The PMI assemblies in the SA matrix create a percolation network capable of bulk-electron transfer under illumination. These PMI–SA materials were then 3D-printed on conductive substrates to create 3D hydrogel photoelectrodes with optimized porosity. The design of these versatile hybrid materials was bioinspired by the soft matter environment of natural photosynthetic systems and opens the opportunity to carry out light-to-fuel conversion within soft matter with arbitrary shapes and particular local environments.

36 MATERIALS SCIENCE↗