Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Microstructure characterization of Cu processed by compression with oscillatory torsion

High purity Cu (99.9%) was subjected to severe plastic deformation up to a total effective strain ε{sub ft} = 130 through compression with the oscillatory torsion method at room temperature. This method produces an ultrafine grain microstructure. The microstructure evolution was investigated with respect to the value of the total effective strain using a scanning electron microscope with an electron-backscattered diffraction technique and a scanning transmission electron microscope. The results of the structural analyses show that increasing ε{sub ft} from 2 to 50 causes progress in the grain refinement. A quantitative study of the microstructure parameters, such as fraction of high angle boundaries, grain and subgrain diameter, and the area fraction of grains up to 1 μm, shows that deformation at ε{sub ft} = 45 guaranteed the best conditions for refining the microstructure of Cu. Using high values of ε{sub ft} in the range 60 to 130 restricts grain refinement because intensive recovery begins to dominate in the microstructure. - Highlights: • Cu was processed by SPD metodto an effective strain 130. • The microstructure evolution has been investigated. • The method allows to produce an ultrafine grain microstructure.

36 MATERIALS SCIENCE↗

Effect of Deformation Temperature on Dynamic Recrystallization and CSL Grain Boundary Distribution of Fe-36%Ni Invar Alloy

This paper investigated the effect of deformation temperatures on microstructure evolution and grain boundary character distribution (GBCD) of Fe-36%Ni Invar alloy during hot compression tests. The isothermal hot deformation tests were carried out in a temperature range of 850-1100 °C and a strain rate of 0.01 s{sup −1}. The grain boundary character distribution was based on the Σ3{sup n} (n = 1, 2, 3,…) coincidence site lattice (CSL) boundaries. The experimental results show that the extent of dynamic recrystallization significantly expanded at the strain rate of 0.01 s{sup −1} with the increase in temperature and this phenomenon was consistent with the evolution tendency of Σ3{sup n} boundaries. To some degree, the increasing proportion of typical low-ΣCSL boundaries, especially the increasing trend of Σ3, positively promoted the wider process of dynamic recrystallization.

36 MATERIALS SCIENCE↗

Characterization and Rationalization of Microstructural Evolution in GRCop-84 Processed by Laser-Powder Bed Fusion (L-PBF)

In this study, prismatic geometries of GRCop-84 [Cu-8Cr-4Nb (at. pct)] were built with laser-powder bed fusion (L-PBF) process. The samples were sectioned parallel or perpendicular to the build direction and characterized in the as-built and after post-processing with a hot-isostatically pressing (HIP) treatment. The microstructure and phase evolutions were evaluated with optical microscopy, scanning electron microscopy (SEM), electron backscattered diffraction (EBSD), and high-temperature X-ray diffraction (HTXRD) up to 1223 K. The samples in the as-built conditions exhibited predominantly columnar epitaxial and misoriented Cu-FCC grains. The microstructure evolutions are discussed based on locations within the overall build geometry, the dynamics of small melt pool shape and sectioning effects. The above grain structure did not change significantly during post-process HIP treatment. The stability of this FCC grain structure is attributed to the formation of primary stable Cr 2 Nb (Laves phase) during L-PBF, even before the emergence of FCC grains from liquid. The stability of Cr 2 Nb in both as-built and HIPed samples were evaluated using high-temperature X-ray diffraction measurements and compared with that of gas-atomized powder. The significance of these results is discussed with reference to aerospace applications.

36 MATERIALS SCIENCE↗

The effect of thermal-aging on the microstructure and mechanical properties of 9Cr ferritic/martensitic ODS alloy

In this paper, the thermal-stability of 9Cr F/M ODS alloy was evaluated by the aging treatment in the air at 700 degrees C for 10 h, 100 h, 1000 h, and 2005 h. The variations of mechanical properties with different aging periods were tested in terms of tensile testing and vickers microhardness. And the microstructural evolution of strengthening particles and grain morphologies in the 9Cr F/M ODS alloys were characterized using field emission scanning electron microscopy, transmission electron microscopy and high-energy X-ray diffraction. It was found that the as-rolled 9Cr F/M ODS alloy slightly recovered without recrystallization during the initial stage of less than 10 h aging time, resulting in the slight loss of tensile strength and microhardness and the increase of elongation. With the aging time prolonged to 2005 h, several of nano-sized Y-Ti-O particles coarsened and the composition changed to Y-Ti-Al-O, and the number density of large size nitride precipitations increased and the composition also changed from TiN to (Ti,AI)N. Meanwhile, some of grains tend to grow up in some preferential directions due to the zener pinning effect by the localized uneven distributed particles inside the grains, causing more particles, especially the particles with a size of larger than 40 nm, located at grain boundaries. These microstructural evolutions lead to the increasing of microhardness and a little bit decreasing of eleongation during 10 h-2005 h, and the increasing of tensile strength during 10 h-1000 h with the subsequent slight decreasing during 1000 h-2005 h. In conclusion, 9Cr F/M alloy shows a relatively good thermal-aging stability at 700 degrees C for 2005 h.

36 MATERIALS SCIENCE↗

Microstructure Evolution of Ultra-Fine-Grained AZ31 B Magnesium Alloy Produced by Submerged Friction Stir Processing

Ten-millimeter-thick strain-hardened AZ31B-H24 magnesium sheets were subjected to friction stir processing (FSP) in air and submerged friction stir processing (SFSP) under water to investigate their microstructures and microhardness properties. Different rotational speeds of 500, 630, 800, and 1000 rpm and traverse speeds of 50, 100, 200, and 350 mm/min were employed for processing the materials. For SFSPed samples, the rotational speed of 500 rpm and 200 mm/min of traverse speed resulted in an ultra-fine-grained structure with a minimum grain size of about 400-500 nm, which is half compared to that of FSPed. It was found that both processes led to variation of crystallographic orientation, and enhancing the rotational speed and lowering the traverse speed promoted the development of a {0002} basal texture. The microhardness of SFSPed material increased significantly up to 110% (~ 95 Hv), while the microhardness was 45% (~ 65 Hv) higher than the base metal (~ 45 Hv) for FSPed material.

36 MATERIALS SCIENCE↗

Chromium Tolerant, Highly Active and Stable Electrocatalytic Internal Surface Coating for Cathode of Commercial SOFCs (Final Report)

This project is aimed to develop a chromium (Cr) tolerant, highly active, and stable coating layer on the internal surfaces of the porous composite cathode from commercially available SOFCs. Such coating layer was developed using the additive manufacturing process of Atomic Layer Deposition (ALD) and has been applied on the cathode consisting of either an electronic conductor of LaxSr 1-x MnyO 3-δ (LSM) or mixed ionic and electronic conducting La x Sr 1-x Co y Fe 1-y O 3-δ (LSCF). PI's work has demonstrated that the internal surface of cathode from the commercial cells, can be further tailored using ALD coating to dramatically enhance the cell performance. For instance, ALD layer consisting heterostructured nano composite of nano-Pt and nano-(Mn 0.8 Co 0.2 ) 3 O 4 oxide on the internal surface of porous LSM/YSZ cathode from SOFCs, has resulted in the large reduction of the cell polarizations resistance by up to 53%, and enormous increase of power density over 370%. For the cells with LSCF/Sm 2 O 3 doped CeO 2 (SDC) cathode, the conformal layer of nano-composite consisting of superjacent CoOx and subjacent minimum amount of Pt nano-grains has resulted in the power density enhancement by 126% for the large scale industry tubular cells at 750°C, and both the performance enhancement and nanostructure of the ALD layer are stable over ~ 2000 h continuous operation performed at industry test station. In the meanwhile, those ALD coating layer developed by PI's work is also inherently Cr-tolerant, and could act as physical barrier for preventing Cr diffusion into the cathode backbone, so as to mitigate the Cr poisoning effect on the cathode. In this project, the impact of Cr on the performance of those ALD coated commercial cells has been evaluated. Based on evolution of the cell performance, the ALD coating layer chemistry and ALD coating layer thickness has been optimized to maximize the overall Cr tolerance, cell power density and cell longevity. Different ALD coating has been applied onto the internal surface of LSM/YSZ and LSCF/SDC backbone respectively. The architecture/scaffold structures on the internal surface of different cathode, designed by this project, was catalogued and analyzed using High Resolution Transmission Electron Microscopy (HRTEM), and cell power/durability performance are assured via comprehensive electrochemical performance testing in the industry operation relevant conditions. The impact of the electrochemical operation current density, the water humidity, the cell operation temperature, and cell operation duration on the Cr tolerance of ALD coated cells has been systematically investigated. There is completely different nanostructure degradation mechanisms between LSM and LSCF cells induced by Cr contamination. For the LSCF/SDC baseline cell, With the Cr source, there is no apparent Sr surface segregation phase even for the baseline cell operated for 3000 h at 750 °C. With the Cr source, there is significant amorphous (SrCr)Ox phase accumulated in the original pore region. For the commercial baseline cells, Cr contaminants on the LSM electrode severely impacted the entire cell's electrochemical performance and nanostructure degradation. Those degradations include (1). Peak power density loss of 64 % after 109 h of operation. The dramatic increase in Rp (2). They are cracking at LSM/SSZ interface, LSM grains. SSZ remains intact but with (CrMn)Ox. By contrast, ALD coating (MnCo)Ox/Pt dramatically improves the Cr resistance, as follows (1). ALD-coated cell with a power density is 280-380 % of the baseline cell, depending on the ALD layer thickness. (2). For a cell with a 20 nm thick ALD layer, there is a large performance enhancement (> 200 % power density) induced by ALD coating of Cr-tolerant Mn 0.8 Co 0.2 Ox. (3). For a cell with a 20 nm thick ALD layer, after 168 h at 750 °C power density of the ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination for 109 h. The ALD coating on the internal surface of cathode developed by this project integrated multi-functions. Those multi-functions include (1). Dramatically improving the cell power density for the commercial cells; (2). Dramatically improving contamination resistance of the cathode, for being an excellent protection coating layer sealing off Cr contamination. (3). Dramatically increasing the cell longevity by potentially preventing the microstructure evolution and grain coarsening of the cathode. Overall, this project will provide a simple solution to simultaneously enhance power density and increase the reliability, robustness, and endurance of commercial SOFCs, over the entire operating temperature range of 650-800 °C. For the inherently functional SOFC, the ALD coating of LSM based cathode mitigate the Cr-contamination. Power density of ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination. In addition to SOFCs, the novel on-demand design approach and creation of multifunctional heterogeneous architecture on the electrode surface presented in this work opens further research for their application in other types of fuel cells, batteries, and sensors for which electrochemical reactions on the surface are similarly critical.

36 MATERIALS SCIENCE↗

Near-isothermal furnace for in situ and real time X-ray radiography solidification experiments

In this paper, we present a newly developed near-isothermal X-ray transparent furnace for in situ imaging of solidification processes in thin metallic samples. We show that the furnace is ideally suited to study equiaxed microstructure evolution and grain interaction. To observe the growth dynamics of equiaxed dendritic structures, a minimal temperature gradient across the sample is required. A uniform thermal profile inside a circular sample is achieved by positioning the sample in the center of a cylindrical furnace body surrounded by a circular heater arrangement. Performance tests with the hypo-eutectic Al-15wt.%Cu and the near-eutectic Al-33wt.%Cu alloys validate the near-isothermal character of the sample environment. Controlled cooling rates of less than 0.5 K min{sup −1} up to 10 K min{sup −1} can be achieved in a temperature range of 720 K–1220 K. Integrated in our rotatable laboratory X-ray facility, X-RISE, the furnace provides a large field of view of 10.5 mm in diameter and a high spatial resolution of ∼4 μm. With the here presented furnace, equiaxed dendrite growth models can be rigorously tested against experiments on metal alloys by, e.g., enabling dendrite growth velocities to be determined as a function of undercooling or solutal fields in front of the growing dendrite to be measured.

36 MATERIALS SCIENCE↗

Abnormal grain growth in AISI 304L stainless steel

The microstructural evolution during abnormal grain growth (secondary recrystallization) in 304L stainless steel was studied in a wide range of annealing temperatures and times. At relatively low temperatures, the grain growth mode was identified as normal. However, at homologous temperatures between 0.65 (850 °C) and 0.7 (900 °C), the observed transition in grain growth mode from normal to abnormal, which was also evident from the bimodality in grain size distribution histograms, was detected to be caused by the dissolution/coarsening of carbides. The microstructural features such as dispersed carbides were characterized by optical metallography, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, and microhardness. Continued annealing to a long time led to the completion of secondary recrystallization and the subsequent reappearance of normal growth mode. Another instance of abnormal grain growth was observed at homologous temperatures higher than 0.8, which may be attributed to the grain boundary faceting/defaceting phenomenon. It was also found that when the size of abnormal grains reached a critical value, their size will not change too much and the grain growth behavior becomes practically stagnant. - Highlights: • Abnormal grain growth (secondary recrystallization) in AISI 304L stainless steel • Exaggerated grain growth due to dissolution/coarsening of carbides • The enrichment of carbide particles by titanium • Abnormal grain growth due to grain boundary faceting at very high temperatures • The stagnancy of abnormal grain growth by annealing beyond a critical time.

36 MATERIALS SCIENCE↗

The microstructure and mechanical behaviors of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy produced by laser melting deposition

The microstructure and mechanical properties of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy produced by laser melting deposition have been investigated. The columnar grains of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy due to the layer-by-layer epitaxial growth from the underlying template grains during laser melting deposition, which is roughly parallel to the deposition direction, had been found by optical microscopy; strong [101{sup ¯}2]{sub α} crystallographic texture has been confirmed by X-ray diffraction and electron backscattered diffraction. Depending on the last heating history, the microstructure of the alloy undergoes a continued change opposite to the deposition direction: martensitic α′ (transformed β); coarsened primary α laths with transformed β; coarsened primary α laths; and the fine basketweave microstructure with a few coarsened α laths or annealed martensitic α′. The average Vickers micro-hardness value of the alloy is 364 HV. The alloy parallel to the deposition direction presents lower tensile strength (925 MPa) and better elongation (18.8%), compared with 1025 MPa and 8.2% of that vertical to the deposition direction, which has been discussed using its microstructure characterization. - Highlights: • The columnar grains and strong [101{sup ¯}2]{sub α} crystallographic texture of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy due to the epitaxial growth from the underlying template grains • The microstructure evolution of the alloy depends on the last heating history. • The specimen parallel to the deposition direction presents lower ultimate tensile strength and higher elongation than the specimen vertical to the deposition direction.

36 MATERIALS SCIENCE↗

Ghost microstructure evolution and identification in the coarse grain heat affected zone of 2.25Cr-1Mo-V-Ti steel using tint etching

Microstructural characteristics of the CGHAZ (coarse grained heat affected zone) made of the 2.25Cr-1Mo-V-Ti material for the thermal power plant boiler tube were discussed using the technique of tint etching. To conduct the micro structural characterization, the sample on which CGHAZ was produced by using a high temperature thermal cycle simulator, Gleeble 3500 equipment was used for comparative analyses using the existing Nital etching (ASTM E407-74) and the alkaline etching (ASTM E40785). The latter was used to observe a specific phase. For the microstructure on which the alkaline etching was experimented, the shape of a black strip (Ghost microstructure) in a few microns was observed, which was not observed from the Nital etching. It was found from the phase identifications based EPMA, EBSD and TEM experiments that the image of the black strip in a few microns represented the alpha phase in which C, Cr and Mo became segregated. In addition, it was verified that austenite and M{sub 23}C{sub 6} phase were present around the segregated zone. Based on such results, the mechanism by which the image of the black strip in a few microns was formed at the CGHAZ. In this study, we have investigated the mechanism of the appeared black strip in the CGHAZ. - Highlights: •Ghost microstructure was observed which was not observed from the nital etching. •Ghost microstructure has high concentrations of carbon and molybdenum than matrix. •Schematic illustration proposed of why Ghost microstructure was generated. •Ghost microstructure caused by partial dissolution of M{sub 23}C{sub 6} precipitation.

36 MATERIALS SCIENCE↗

GrainGNN: A dynamic graph neural network for predicting 3D grain microstructure

We propose GrainGNN, a surrogate model for the evolution of polycrystalline grain structure under rapid solidification conditions in metal additive manufacturing. High fidelity simulations of solidification microstructures are typically performed using multicomponent partial differential equations (PDEs) with moving interfaces. The inherent randomness of the PDE initial conditions (grain seeds) necessitates ensemble simulations to predict microstructure statistics, e.g., grain size, aspect ratio, and crystallographic orientation. Here, currently such ensemble simulations are prohibitively expensive and surrogates are necessary.In GrainGNN, we use a dynamic graph to represent interface motion and topological changes due to grain coarsening. We use a reduced representation of the microstructure using hand-crafted features; we combine pattern finding and altering graph algorithms with two neural networks, a classifier (for topological changes) and a regressor (for interface motion). Both networks have an encoder-decoder architecture; the encoder has a multi-layer transformer long-short-term-memory architecture; the decoder is a single layer perceptron.We evaluate GrainGNN by comparing it to high-fidelity phase field simulations for in-distribution and out-of-distribution grain configurations for solidification under laser power bed fusion conditions. GrainGNN results in 80%–90% pointwise accuracy; and nearly identical distributions of scalar quantities of interest (QoI) between phase field and GrainGNN simulations compared using Kolmogorov-Smirnov test. GrainGNN's inference speedup (PyTorch on single x86 CPU) over a high-fidelity phase field simulation (CUDA on a single NVIDIA A100 GPU) is 150×–2000× for 100-initial grain problem. Further, using GrainGNN, we model the formation of 11,600 grains in 220 seconds on a single CPU core.

36 MATERIALS SCIENCE↗

Nanostructure formation during accumulative roll bonding of commercial purity titanium

In this investigation, commercial purity titanium (CP–Ti) was subjected to accumulative roll bonding (ARB) process up to 8 cycles (equivalent strain of 6.4) at the ambient temperature. Transmission electron microscopy (TEM) and X–ray diffraction line profile analysis (XRDLPA) were utilized to investigate the microstructure and grain size evolution. Both characterization techniques could clarify the non–uniform microstructure in the early stages and the uniform microstructure in the final stages of the process. The effectiveness of ARB for the fabrication of the nano–grained structure in CP–Ti was revealed. It was found that the SFE is not the only factor affecting grain refinement, as compared with other studies on ARB of FCC materials. Influence of other factors such as the melting temperature and the crystalline structure of the material was determined on the grain refinement. - Highlights: •Nano–grained commercial purity titanium was produced by accumulative roll bonding. •TEM and XRDLPA were used for the characterization of the microstructure. •Important factors affecting the grain size of ARBed materials were discussed.

36 MATERIALS SCIENCE↗

Rapid grain refinement and compositional homogenization in a cast binary Cu50Ni alloy achieved by friction stir processing

Friction stir processing (FSP) has been increasingly adopted for joining and processing materials in automotive, aerospace and industrial construction. During FSP a dynamic competition between high-speed shear deformation and deformation-induced heating brings about a complex competition between multiple dynamic microstructural evolution mechanisms making it difficult to predict the microstructural evolution pathway. Hence, improved understanding of microstructural evolution mechanisms during FSP can be beneficial for continued growth in the adoption of FSP for demanding applications of future. Towards this goal, this study uses a model binary Cu – 50 at.% Ni alloy to clarify the effect of single and double pass FSP on the microstructural evolution of a coarse grained and compositionally heterogeneous cast microstructure. High energy synchrotron X-ray diffraction, electron backscatter diffraction, and nanoindentation are used to clarify the microstructural evolution due to FSP. The process of compositional homogenization of as-cast segregations is studied by energy dispersive spectroscopy and atom probe tomography. Our results show that a single fast FSP pass at 30 mm.s -1 produces a 100 µm deep layer of submicrometric and hall-petch hardened CuNi grains. The initial cast compositional heterogeneities in a micrometric scale is rapidly transformed to nano-sized domains, mainly confined at grain boundaries. Double pass FSP increases the penetration depth of the processed layer and leads to a 2.9 times grain growth relative to single pass FSP. Grain fragmentation, discontinuous dynamic recrystallization, grain growth, and twinning mechanisms are discussed. In conclusion, these results highlight the value of FSP for ultrafast grain refinement and compositional homogenization of cast alloys.

36 MATERIALS SCIENCE↗

Microstructural evolution and mechanical properties on an ARB processed IF steel studied by X-ray diffraction and EBSD

Accumulative Roll Bonding (ARB) is one of the so-called severe plastic deformation (SPD) processes, allowing the production of metals and alloys with ultrafine (micro-nano) structures. Materials with ultrafine grains present attractive properties like the simultaneous increase in strength and ductility. Our interest in these materials is focused on their microstructural evolution during ARB processing, eventually responsible for the enhancement of those mechanical properties. In the current work we follow the evolution of the microstructure in an interstitial-free (IF) steel deformed by ARB after consecutive processing cycles, by means of Electron BackScatter Diffraction (EBSD) and X-ray diffraction (XRD). Particularly, we present results related to texture, grain (GS) and domain sizes, grain boundary character, density of Geometrically Necessary Dislocations (GND), Grain Orientation Spread (GOS), lattice parameters, microstrain, dislocation density and their spatial arrangement. After 5 ARB cycles the system shows a microstructure constituted mainly by submicrometric grains with high angle boundaries and low presence of dislocations inside the grains. - Highlights: •The evolution of microstructure is followed simultaneously by using GAM, GOS and GND (EBSD) and XRD. •LAGBs and subgrains disappear after few cycles SSDs and HAGBs persist at the end. •Dynamic recrystallization counterbalances dislocation arrays and diminishes hardening rate. •Grain size stabilization is revealed as a mechanism for increasing ductility after few ARB cycles.

36 MATERIALS SCIENCE↗

Order parameter re-mapping algorithm for 3D phase field model of grain growth using FEM

Phase field modeling (PFM) is a well-known technique for simulating microstructural evolution. To model grain growth using PFM, typically each grain is assigned a unique non-conserved order parameter and each order parameter field is evolved in time. Traditional approaches using a one-to-one mapping of grains to order parameters present a challenge when modeling large numbers of grains due to the computational expense of using many order parameters. This problem is exacerbated when using an implicit finite element method (FEM), as the global matrix size is proportional to the number of order parameters. While previous work has developed methods to reduce the number of required variables and thus computational complexity and run time, none of the existing approaches can be applied for an implicit FEM implementation of PFM. Here, we present a modular, dynamic, scalable reassignment algorithm suitable for use in such a system. Polycrystal modeling with grain growth and stress require careful tracking of each grain’s position and orientation which is lost when using a reduced order parameter set. In conclusion, the method presented in this paper maintains a unique ID for each grain even after reassignment, to allow the PFM to be tightly coupled to calculations of the stress throughout the polycrystal. Implementation details and comparative results of our approach are presented.

36 MATERIALS SCIENCE↗

The impact of anisotropic thermal expansion on the isothermal annealing of polycrystalline α -uranium

Although grain growth impacts microstructural evolution in a wide variety of materials systems, the effect of anisotropic thermal expansion on grain boundary mobility and texture evolution has not been widely studied. Anisotropic thermal expansion occurs in multiple non-cubic metals, and the thermomechanical processing behavior of these materials can be better understood with further study into the impact of thermal expansion on grain boundary mobility and texture evolution. In this work, we develop a mesoscale phase field model of grain growth that includes the effect of anisotropic thermal expansion, which is applied to study polycrystalline α-uranium, a highly anisotropic metal. Three-dimensional simulations on polycrystalline a-uranium with and without thermal expansion eigenstrains are performed to study the grain boundary mobility and texture evolution as a function of temperature. A strain-free temperature of 933 K is selected, and the system is studied at within the range of 873 – 933 K at intervals of ten degrees, resulting in increasing thermal eigenstrain with decreasing temperature. We also estimate a grain boundary mobility prefactor and activation energy based on existing experimental data of isothermal annealing of α-uranium. The grain boundary mobility is found to display significant deviation from Arrhenius behavior with the inclusion of thermal expansion eigenstrain as the amount of thermal eigenstrain (and thus elastic strain energy within the system) increases. This result explains an experimentally observed grain boundary mobility deviation from Arrhenius behavior. Furthermore, the texture evolution is affected, such that the grain orientations become less random with increasing thermal eigenstrain, which could explain experimentally observed texture behavior. These results indicate that the effect of thermal expansion should be considered when predicting the thermomechanical processing behavior of α-uranium and other materials with anisotropic thermal expansion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Understanding the effect of crystal anisotropy on grain growth, texturing and transport via the orthorhombic ?-U system [Slides]

The alpha phase of uranium exhibits the orthorhombic crystal structure, resulting in significant physical property anisotropy. These complex properties make the material challenging to work with in engineering settings but provide a rich arena to investigate the fundamental, multi-scale effects of anisotropy on physical behaviors such as grain growth and microstructure evolution under irradiation. We apply molecular dynamics and phase field modeling to study mass transport and grain growth in alpha-uranium. We characterize the mobilities of crystalline defects and the interfacial energy, and We find that the grain boundary energy is highly variable depending on the interface structure and that the relative rates of defect transport change with temperature. We also find that anisotropic thermal expansion has a significant impact on grain growth kinetics and texture development. Our results are used to explain experimental observations and to provide a basis for further hypotheses into the complex physical behavior of alpha-uranium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Engineering grain boundary anisotropy to elucidate grain growth behavior in alumina

Current grain growth models have evolved to account for the relationship between grain boundary energy/mobility anisotropy and the five degrees of grain boundary character. However, the role of grain boundary networks on overall growth kinetics remains poorly understood. To experimentally investigate this problem, a highly textured Al 2 O 3 was fabricated by colloidal casting in a strong magnetic field to engineer a unique spatial distribution of grain boundary character. Microstructural evolution was quantified and compared to an untextured sample. From this comparison, a prevalence of (0001)/(0001) terminated grain boundaries with anisotropic networks were identified in the textured sample. These boundaries and their networks were found to be driving grain growth at a faster rate than predicted by models. These findings will allow better modelling of grain growth in real systems by experimentally exploring the impact thereon of grain boundary plane anisotropy and relative energy/mobility differences between neighboring boundaries.

36 MATERIALS SCIENCE↗