Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphene oxide membranes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Scalable aqueous-phase fabrication of reduced graphene oxide nanofiltration membranes by an integrated roll-to-roll (R2R) process

Economic fractionation of multicomponent biomass-derived streams is a key challenge in biobased fuels and chemicals production. Kraft black liquor (BL) is generated at ~1 billion tons/yr globally from biomass pulping and contains ~15wt% total solids including lignin, hemicellulose fragments, and inorganics. Membrane-based BL concentration is attractive but challenged by low solute rejections and poor stability in BL, which combines alkaline pH (~13), high dissolved solids content (15+ wt%) and high temperature (70–85°C). Here we discuss the scaled fabrication and characterization of reduced graphene oxide (rGO) nanofiltration membranes by slot die coating on a roll-to-roll (R2R) with integrated vacuum filtration. Here, we obtain high-quality 90×30 cm rGO membranes (referred to as “R2R-rGO membranes” in this work) with ~100 nm average thickness supported on porous poly(ethersulfone) (PES) sheets, and an effective area of 2700cm 2 . We present characterizations of their microstructure and uniformity as mapped over large areas by scanning electron microscopy (SEM), ellipsometry, adhesion test and X-ray photoelectron spectroscopy (XPS). The constructed ellipsometry model for the rGO membrane/PES substrate composite was successfully applied to 48 different locations of the R2R-rGO membranes. The R2R-rGO membranes showed >98% lignin rejection with a steady state flux of ~12 LMH at 50bar in a 15.7wt% total solids (TS) kraft BL stream at 72°C and 2–3 gal/min crossflow rates. Slot die coating on a R2R platform with integrated vacuum filtration can enable rapid fabrication of high-quality GO membranes at scale without organic solvents or volatile organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Using Al 3+ to Tailor Graphene Oxide Nanochannels: Impact on Membrane Stability and Permeability

Graphene oxide (GO) membranes, which form from the lamination of GO sheets, attract much attention due to their unique nanochannels. There is much interest in controlling the nanochannel structures and improving the aqueous stability of GO membranes so they can be effectively used in separation and filtration applications. This study employed a simple yet effective method of introducing trivalent aluminum cations to a GO sheet solution through the oxidation of aluminum foil, which modifies the nanochannels in the self-assembled GO membrane by increasing the inter-sheet distance while decreasing intra-sheet spacing. The Al 3+ modification resulted in an increase in membrane stability in water, methanol, ethanol, and propanol, yet decreased membrane permeability to water and propanol. These changes were attributed to strong interactions between Al 3+ and the membrane oxygenated functional groups, which resulted in an increase in membrane hydrophobicity and a decrease in the intra-sheet spacing as supported by surface tension, contact angle, atomic force microscopy, and X-ray photoelectron spectroscopy measurements. Our approach for forming Al 3+ modified GO membranes provides a method for improving the aqueous stability and tailoring the permeation selectivity of GO membranes, which have the potential to be implemented in vapor separation and fuel purification applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Printed graphene oxide-based membranes for gas separation and carbon capture

Graphene oxide (GO)-based separation membranes have demonstrated the great potential to separate molecules and ions by the interlayer spacing with tunable nano-sized channels. The scalable fabrication of GO-based gas separation membranes, however, remains challenging, although a few preparation approaches have been reported. Here in this work, we present for the first time that the co-solvent ink-jet printing, as a fast and scalable method, can be utilized for scalable GO-based gas separation membrane preparation. Large-area (>100 cm 2 ), ultrathin, and high-quality GO membrane was successfully deposited on commercial polysulfone (PS) support, and characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and X-ray diffraction, et al., Selective hydrogen (H 2 ) and helium (He) transport over carbon dioxide (CO 2 ) and nitrogen (N 2 ) was demonstrated for the printed GO membrane. To further explore the separation potential of the printed GO-based gas membrane, additives for facilitated molecular transport were incorporated during the membrane printing process. By inserting CO 2 -philic agents into the printed GO membrane, highly efficient separation of CO 2 from N 2 was achieved with CO 2 /N 2 selectivity of 70 and CO 2 permeance as high as 2,500 GPU. The strategy proposed here may provide guidance for large-scale GO-based gas separation membrane production and a versatile approach for applying other functional 2-dimensional materials towards the membrane separation application.

42 ENGINEERING↗
DOE OSTI2020

Ammonia Permeation Through Inorganic Membranes

Moisture probes are used in the tritium facility to measure the moisture content of the gas stream. When tritium reacts with nitrogen to form ammonia, the ammonia gas damages the sensitive moisture probe. The gas stream tested during this experiment for moisture probe protection is composed of nitrogen and argon gas in conjunction with ammonia and water vapor. The gas stream is filtered through an inorganic membrane due to the high reactivity of tritium and a residual gas analyzer (RGA) is used to measure the ammonia and water vapor in the gas stream, as well as the permeability of nitrogen and argon through the inorganic membranes. The membranes tested were boron nitride and silver. The permeability was compared for each membrane at different pressures and flow rates. Fourier-transformed infrared spectroscopy (FT-IR) was used to compare the membranes before and after ammonia permeation. Ammonia gas is a byproduct formed from tritium gas reacting with nitrogen in the gas stream, similar to the Haber Process which occurs when hydrogen reacts with nitrogen [2]. The corrosive nature of ammonia damages metals and sensitive instruments such as moisture probes. Moisture probes are essential in various gas and liquid processes for measuring the moisture content of a gas. Membrane research has found that graphene oxide membranes successfully uptake ammonia from the gas stream at a humidity of approximately 30% at which point the pores pin closed, preventing gas permeation. Further research is being conducted to find an inorganic membrane that will prevent ammonia permeation thus circumventing damage to the sensitive moisture probe. The permeation measurements for argon and nitrogen gas and water and ammonia vapor were measured at various pressures of 800, 1000, 1200, 1500, 1800, and 2000 torr. The permeability average (PA) was calculated for each filter using a Barrer calculation. The average permeations for each filter were then compared. The gas composition was measured using the RGA Nitrogen was permeated through the membranes after ammonia permeation and a FT-IR spectrum was obtained. Boron Nitride: As the nitrogen pressure increased, the permeability of the membrane decreased from 800-1200 torr and remained relatively unchanged from 1200-2000 torr. The membrane exhibited a slight decrease in argon permeability from 800-1200 torr and a slight increase from 1500-2000 torr. The boron nitride membrane when permeated with ammonia and nitrogen prevented less ammonia permeation compared to the blank filter. The boron nitride filter demonstrated a decrease in permeability after ammonia permeation. Silver Membrane: When permeated with nitrogen alone, the membrane permeability decreased from 800 torr to 1200 torr. The permeability of the membrane showed little difference as pressure increased from 1200 torr. When permeated with argon, the same phenomenon occurred but on a much smaller scale. When compared to the blank and the boron nitride membranes the silver membrane exhibited significantly lower permeability. This may be in part due to the coating on the silver membrane and differences in pore size of the membranes. During permeation with ammonium hydroxide vapor and nitrogen, the partial pressure of the ammonia increased as compared to the blank membrane. The permeability before and after permeation with ammonia and nitrogen were compared. Permeability values suggested that after being permeated with the ammonia that the permeability for lower pressures increased slightly. There was no significant change in the FT-IR spectrums before and after permeation. Future work: Continue testing various inorganic membranes for ammonia permeation. Further research chemical separation of ammonia from the gas stream, which may prove difficult due to the high reactivity of tritium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Solar-thermal membrane for dewatering aqueous organic-acid solutions

A thermally conductive porous membrane has been developed to directly absorb solar energy and conduct heat that can effectively evaporate liquid water at the interface between the membrane and the bulk feed solution. Here, black, porous, thermally conductive graphite foam support is employed as an effective photothermal-energy absorber and heat conductor that heats up an aqueous feed solution to produce vapor. Graphite nanoparticle-slurry coating is applied onto the foam surface to reduce the pore size and generate a microporous membrane. Then, application of a dense graphene oxide membrane coating as an active separation layer on the microporous nanoparticle surface of internal foam channels allows vapor permeation of volatile molecules. Acetic acid/water solution was studied as a model feed system to experimentally demonstrate effective separation. This model vapor permeation system demonstrates excellent acetic acid separation, with a separation factor of 8.3, under simulated 0.7 sun irradiation. The membrane hydrophobicity and nanostructure, including pore size and surface chemistry, played a significant role in enabling high permselectivity of water vapor over acetic acid molecules, as well as liquid solution. Pore size reduction from open pores to a nonporous dense layer in the membrane enables effective separation of water vapor from the organic vapor, while it reduces the permeation flux. Also, the hydrophilicity of the membrane surface shows ~3 times higher permeation flux with higher permselectivity, compared with the hydrophobic membrane surface. This work introduces a process of directly using renewable energy instead of conventional heating to drive selective separation of water from organic acids.

14 SOLAR ENERGY↗
DOE OSTI2024

Scalable Graphene Oxide Hollow Fiber Membranes for Dye Desalination Enabled by Multi‐Purpose Polyamine Functionalization

2D nanosheets such as graphene oxide (GO) can be stacked to construct membranes with fine-tuned nanochannels to achieve molecular sieving ability. These membranes are often thin to achieve high water permeance, but their fabrication with consistent nanostructures on a large scale presents an enormous challenge. Herein, GO-based hollow fiber membranes (HFMs) are developed for dye desalination by synergistically combining chemical etching to form in-plane nanopores (10–30 nm) to increase water permeance and polyamine functionalization to improve underwater stability and enable facile large-scale production using existing membrane manufacturing processes. HFM modules with areas of 88 cm 2 and GO layer thicknesses of ≈500 nm are fabricated, and they exhibited a stable dye water permeance of 75 L m −2 h −1 bar −1 , rejection of >99.5% for Direct red and Congo red, and Na 2 SO 4 /dye separation factor of 300–500, superior to state-of-the-art commercial membranes. Furthermore, the versatility of this approach is also demonstrated using different short polyamines and porous substrates. This study reveals a scalable way of designing 2D materials into high-performance robust membranes for practical applications.

amine functionalization↗
DOE OSTI2024

Bench-scale Development of a Transformational Graphene Oxide-based Membrane Process for Post-combustion CO 2 Capture

Graphene-based materials, such as graphene and graphene oxide (GO), have been considered as next-generation membrane materials. GTI Energy and The State University of New York at Buffalo (UB) have been developing a transformational GO-based membrane process (designated as GO2) that integrates a high CO 2 /N 2 selectivity membrane (GO-1) and a high CO 2 flux membrane (GO-2) for post-combustion CO 2 capture. An innovative membrane structure, consisting of GO nanochannels intercalated by single-walled carbon nanotube (SWCNT), was developed. The membrane prepared on hollow fiber substrate showed CO 2 permeance as high as 1,300 GPU with CO 2 /N 2 selectivity >200. The membranes were successfully scaled up to effective area of 50-100 cm 2 . The 50-100 cm 2 membranes showed CO 2 /N 2 selectivity ≥200 and CO 2 permeance ≥1,000 GPU for the GO-1 type, and CO 2 /N 2 selectivity ≥20 and CO 2 permeance ≥2,500 GPU for the GO-2 type. The CO 2 capture performance of the GO-based membranes was tested using a simulated flue gas. The testing results indicate that the GO-based membranes are stable in the presence of flue gas contaminants. The GO-based membranes were then further scaled up to a surface area of 1,000 cm 2 . Good stability was achieved during an integrated testing with GO-1 and GO-2 membranes using simulated flue gas. A bench-scale system was designed, constructed, and tested at the National Carbon Capture Center (NCCC). Good stability was achieved during testing of a single-stage process with >10 shutdowns/startups at NCCC. During the integrated testing, the membranes showed good stability at 50°C and 57°C. 70-90% CO 2 removal efficiencies and ≥95% CO 2 purity were validated during the steady state operation at NCCC. Techno-economic analysis indicates the GO2 membrane-based process technology provides a reduction in both the levelized cost of electricity (LCOE) and cost of capture when compared to the reference B12B case presented in the Cost and Performance Baseline for Fossil Energy Plants Volume 1: Bituminous Coal and Natural Gas to Electricity study prepared by the National Energy Technology Laboratory (NETL), before considering any system optimization or improvement opportunities. The benefits are primarily driven by a reduction in the equipment costs of the CO 2 capture process vs. the solvent-based reference process in NETL Case B12B as well as a decrease in the base plant size.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Field Validation of a Pilot-scale Black Liquor Membrane for Water Removal at Ahlstrom-Munksjö Paper Mill in Mosinee, WI

Project Background: The Industrial Technology Validation (ITV) program aims to identify and demonstrate the performance of new, emerging, and underutilized technologies in the industrial sector to help inform decisions towards accelerating commercialization and deployment. Pulp and paper is considered one of the most energy-intensive industries in the manufacturing sector. There are several methodologies for converting wood into pulp in the paper-making industry. The kraft process is a chemical method for producing wood pulp. The kraft process generates black liquor as a byproduct of pulp production. Traditionally, water is evaporated from the liquor by a set of multi-effect evaporators (MEEs), which concentrate weak black liquor (WBL) into strong black liquor (SBL) to support efficient combustion in a recovery boiler. Concentrating black liquor is an energy-intensive step in recovering pulping chemicals and generating high-pressure steam from dissolved wood solids. About 7% of pulp and paper energy usage, or nearly 164 trillion Btu, is used to remove water from black liquor in U.S. kraft pulp mills per year. The U.S. DOE’s IEDO is interested in the black liquor membrane technology evaluated in this report because it offers the potential for a more energy-efficient and less carbon-intensive kraft pulping process across 99 kraft pulp mills in 24 states (Agenda 2020 Technology Alliance 2016). This ITV project validates an innovative black liquor membrane technology for kraft pulp mills to understand its impact and benefits. Via Separations is a technology vendor that developed a graphene oxide membrane system to remove water from WBL before entering the evaporator set. High-pressure positive displacement (HPR) pumps move the black liquor through membranes that separate water and create a more concentrated black liquor. The vendor claims their pre-commercial technology reduces evaporator steam consumption by dewatering WBL before entering the evaporators. They also claim their technology has non-energy benefits such as enhanced soap collection and improved pulp throughput. This evaluation focuses on validating the energy and carbon dioxide (CO 2 e) emissions benefits associated with the membrane system.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Tuning Fabrication Factors for Reduced Graphene Oxide Forward Osmosis Membranes

Forward osmosis (FO) may serve as a near-zero energy approach for wastewater management and selective chemical enrichment with an appropriate FO membrane. There is a need for novel FO membranes with better physical stability, chemical compatibility, and enhanced reverse flux selectivity. In this work, we have systematically studied a variety of factors for fabricating thermally reduced graphene oxide (RGO) FO filtration membranes and have demonstrated that with a comparable water flux, the RGO membranes have an exceptionally large reverse flux selectivity with 1.5 M sodium sulfate draw solution, about 7 times larger than that of cellulose triacetate membranes under the same testing condition. The interlayer spacing of the membranes can be fine-tuned by varying temperatures, so that the free interlayer spacing is less than 0.7 nm after exposure to water. The RGO-based membranes offer a few advantages with high reverse flux selectivity, mechanical robustness with strong adhesion to nylong support membranes without damage after FO tests and tape peel tests, and enhanced chromate and chlorine resistance. Finally, we have further demonstrated that in the FO processes, one can concentrate waste brine while simultaneously harvesting the osmotic energy as electricity, offering potential applications of forward osmosis-based osmotic batteries for powering electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Convenient Confinement: Interplay of Solution Conditions and Graphene Oxide Film Structure on Rare Earth Separations

Graphene oxide (GO) membranes are excellent candidates for a range of separation applications, including rare earth segregation and radionuclide decontamination. Understanding nanoscale water and ion behavior near interfacial GO is critical for groundbreaking membrane advances, including improved selectivity and permeability. Here, we experimentally examine the impact of solution conditions on water and lanthanide interactions with interfacial GO films and connect these results to GO membrane performance. The investigation of the confined films at the air–water interface with a combination of surface-specific spectroscopy and X-ray scattering techniques allows us to understand water and ion behaviors separately. Sum frequency generation spectroscopy reveals a dramatic change in interfacial water organization because of graphene oxide film deprotonation. Interfacial X-ray fluorescence measurements show a 17× increase in adsorbed lanthanide to the GO film from subphase pH 3 to pH 9. Liquid surface X-ray reflectivity data show an additional 2.7 $e^–$ per Å 2 for GO films at pH 9 versus pH 3 as well. These results are connected to GO membrane performance, which show increased selectivity and decreased flux for membranes filtering pH 9 solutions. We posit insoluble lanthanide hydroxides form at higher pHs. Taken together, these results highlight the importance of interfacial experiments on model GO systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Energy efficient membrane-based process for CO 2 capture

Processes and systems for the energy efficient capture of CO 2 from a flue gas stream such as produced or resulting from power plant operation, are provided. The processes and systems integrate the use of high CO 2 /N 2 selectivity membranes and high CO 2 flux membranes, to capture CO 2 . Useful membranes can desirably be graphene oxide-based membranes.

Li, Shiguang↗
DOE OSTI2020

System and method for cooling using a heat exchanger having a membrane

A heat exchanger that includes a membrane of graphene oxide is disclosed, as is a heat exchange system employing such a heat exchanger. The heat exchanger permits the use of water from non-traditional sources, such as waste water, brackish and sea water, in a cooling loop. Clean water and sensible heat permeate through the membrane, simultaneously cooling and purifying water in the cooling loop.

42 ENGINEERING↗
DOE OSTI2022

Effects of ion adsorption on graphene oxide films and interfacial water structure: A molecular-scale description

Herein we discuss graphene oxide as a promising, emerging separation material, as it is durable, dispersible in water, and has naturally forming functional groups. Bulk studies using graphene oxide flakes have demonstrated impressive metal adsorption. However, little interfacial information about water and metal organization near graphene oxide is available. A mechanistic understanding of water and ions interactions with graphene oxide films is critical toward advanced separations, including improved sorption efficiency and membrane regeneration. We study metal ion and local water organization near graphene oxide thin films formed at the air/water interface. These films are not typical membranes and allow us to determine nanoscale information about the graphene oxide-water interface. We accomplish this with x-ray reflectivity (XR), x-ray fluorescence near total reflection (XFNTR), and vibrational sum frequency generation spectroscopy (SFG). These interface-specific techniques provide the electron density profile normal to the interface, number of adsorbed ions, and information about the orientational ordering and hydrogen-bonding network of interfacial water, respectively. Via XFNTR and SFG, we find that trivalent yttrium ions preferentially adsorb to graphene oxide and affect its structure, compared to divalent strontium and monovalent cesium ions. Two different interfacial water populations can be described, based on their hydrogen bonding strength, and the adsorbed ions affect these populations differently. These results provide fundamental information about ion and water organization at the interface and help address the large computational-experimental agreement gap for graphene oxide systems. Additionally, they are relevant for improved soft-scaffold graphene oxide membranes and downstream applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Rapid, Sensitive, Label-Free Electrical Detection of SARS-CoV-2 in Nasal Swab Samples

Rapid diagnosis of coronavirus disease 2019 (COVID-19) is key for the long-term control of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) amid renewed threats of mutated SARS-CoV-2 around the world. Here, we report on an electrical label-free detection of SARS-CoV-2 in nasopharyngeal swab samples directly collected from outpatients or in saliva-relevant conditions by using a remote floating-gate field-effect transistor (RFGFET) with a 2-dimensional reduced graphene oxide (rGO) sensing membrane. RFGFET sensors demonstrate rapid detection (<5 min), a 90.6% accuracy from 8 nasal swab samples measured by 4 different devices for each sample, and a coefficient of variation (CV) < 6%. Also, RFGFET sensors display a limit of detection (LOD) of pseudo-SARS-CoV-2 that is 10 000-fold lower than enzyme-linked immunosorbent assays, with a comparable LOD to that of reverse transcriptionpolymerase chain reaction (RT-PCR) for patient samples. To achieve this, comprehensive systematic studies were performed regarding interactions between SARS-CoV-2 and spike proteins, neutralizing antibodies, and angiotensin-converting enzyme 2, as either a biomarker (detection target) or a sensing probe (receptor) functionalized on the rGO sensing membrane. Finally, taken together, this work may have an immense effect on positioning FET bioelectronics for rapid SARS-CoV-2 diagnostics.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Facilitated Transport Membranes with Tunable Amine-CO 2 Chemistry for CO 2 /H 2 Separation

CO 2 -selective, amine-containing facilitated transport membranes are of great interest for syngas purification since high-pressure H 2 can be retained upon CO 2 removal. A variety of amine-containing polymers have shown decent chemical and thermal stability at aggressive conditions, but their CO 2 /H 2 separation properties are largely limited by the hydrostatic compaction and severe carrier saturation associated with the high syngas pressure. Herein, we report a new approach to enhance the CO 2 permeability by manipulating the steric hindrance of the amine carriers. A series of α-aminoacids with different alkyl or hydroxyethyl substituents are deprotonated by 2-(1-piperazinyl)ethylamine, leading to nonvolatile amine carriers with different degrees of steric hindrance. For hosting the low MW amine carriers, a highly crosslinked poly(vinyl acetal) is synthesized as a water-swellable polymer network. In order to avoid membrane compaction, perforated graphene oxide mono-sheets are dispersed as reinforcement fillers. In the presence of moisture, a bulkier alkyl substituent to the amino site (increasing steric hindrance) destabilizes the carbamate adduct and thus drastically increases the chemisorption of CO 2 , while the incorporation of ethylene oxide groups provides additional physisorption of CO 2 . The enhanced CO 2 solubility significantly mitigates the carrier saturation behavior, and an unprecedented CO 2 /H 2 selectivity greater than 100 is demonstrated at 107 °C and 12.5 atm of CO 2 partial pressure. As the CO 2 partial pressure reduces to 0.4 atm, a less hindered amine yields a higher reactive diffusivity of CO 2 , resulting in a CO 2 permeance of 435 GPU with a selectivity greater than 500. These reaction-mediated polymeric membranes are well above the theoretical upper bound, and they are of great interest for designing a highly-selective membrane process for syngas purification.

08 HYDROGEN↗