Search NASA⌕ Search

SEARCH · Search NASA

Results for “HIGH THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Rapid approach for structural design of the tower and monopile for a series of 25 MW offshore turbines

The goal of further reducing the Levelized Cost of Energy (LCOE) has driven the investigation of large-scale wind turbines. This work presents a simple, rapid and detailed approach for the structural design of the tower and monopile without a controller, but with frequency and high fidelity structural verification. The approach uses an optimization to reduce the mass of the structures while meeting strength, buckling and geometric constraints by using analytical equations. A verification of frequency constraints is performed with BModes, and ANSYS Mechanical APDL is used for high fidelity verification of stress and buckling. The approach is applied to study the design space of three 25 MW offshore wind turbines with different rotor diameters and cone angles, and to evaluate the nacelle center of mass fore-aft location effect. Results obtained show that the tower and monopile are more susceptible to changes in the rotor thrust than the overturning moment even for designs with high pre-cone angle and large distance of the nacelle center of mass from the tower axis. But it is possible to obtain structurally feasible tower and monopile designs for the three 25 MW turbines studied while not exceeding diameter and wall thickness limits. However, mass penalties can be decreased by 0.8-14%, to further reduce the cost of energy, by increasing the diameter limit which may require manufacturing technology development. The approach applied and studies serve to understand the design space of the tower and monopile for a 25 MW turbine, and provide baseline designs that can be used in the development of a controller and evaluation of a full suite of design load cases.

17 WIND ENERGY↗
DOE OSTI2021

Phase Relationships in the Carbon–Titanium–Uranium System for Ultra-High Temperature Nuclear Fuels

Carbides of uranium have attracted interest as fuels for nuclear thermal propulsion (NTP) to drive deep-space exploration owing to their attractive thermal and neutronic properties. Optimization of NTP technology, however, requires ultra-high temperature reactor environments to maximize the ratio of thrust to propellant to achieve peak rocket engine efficiency. Incorporation of transition metals into uranium carbides offers a pathway to increase the melting point of carbide fuels to address the operational challenges posed by NTP. Here, a thermodynamic model has been developed to examine the phase relationships in the C–Ti–U system at NTP conditions. Calculated phase relationships at ultra-high temperatures predict a stable (U, Ti)C solid solution. Additionally, experimental work on C–Ti–U synthesis via arc melting has been carried out, providing data on phase constitution and compositions that can be used to further refine the thermodynamic model that has been developed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Platinum group metal-free (PGM-free) integrated tandem junction photoelectrochemical (PEC) water splitting devices (Final Technical Report)

This project involves using solar light, a photoabsorber, and a catalyst to split water and produce hydrogen. The Department of Energy (DOE) targets for integrated photoelectrochemical (PEC) cells emphasize cost (electrode cost < $200/m 2 ), performance (> 15% solar to hydrogen (STH) efficiency), and stability (> 6 months electrode lifetime), but most approaches skew toward one specific metric. This project exploited interfacial integration of platinum group metal-free (PGM-free) catalysts on the high performance and high value tandem solar cells to attain or exceed the DOE benchmark STH energy conversion efficiency and durability. This was investigated in two thrusts by developing two PEC devices for direct comparison: the first is a high-performance monolithic device based on state-of-the-art GaInP 2 /GaAs tandem solar cells developed at National Renewable Energy Laboratory (NREL), and the second is a high-value device based on earth-abundant wide band gap photoabsorber materials including oxynitride and hybrid organic-inorganic perovskite (HOIP) coupled with commercial narrow band gap silicon (Si). Both these devices were paired with electrocatalysts developed for this purpose at Rutgers University by adapting them to thin films on the photoabsorbers. These catalysts are based on the hydrogen evolution reaction (HER) catalysts (Ni 5 P 4 ), oxygen evolution reaction (OER) catalysts (LiCo 2 O 4 ) previously developed at Rutgers for high-efficiency electrolyzers. For using the high-performance tandem solar cell and Ni 5 P 4 catalysts, we achieved a durability of > 200 h at a STH efficiency of > 10%. For using the high-value wide band gap single junction solar cells on n + Si, we achieved 0.73 mA/cm 2 at 1.23V vs reversible hydrogen electrode (RHE) and -15.9 mA/cm 2 at 0V vs RHE using the oxynitride- and HOIP-based photoelectrodes, respectively. After comparing their photocurrent densities, we down selected the HOIP photoabsorber to couple Si for fabrication of a tandem photocathode. However, due to the COVID-19 pandemic, both the laboratories at Rutgers and NREL were locked down for three months and reopened only partially in 2020. The HOIP/Si tandem photocathode using robust nickel phosphide thin film catalysts cannot be developed within the project period, which is expected to achieve a STH efficiency of > 20%. Also, the low-cost LiCo 2 O 4 OER catalysts need to replace the benchmark IrO 2 for evaluation. Finally, techonomic analysis of full high-performance and high-value integrated PEC devices needs to be carried out for comparison in terms of cost.

08 HYDROGEN↗
DOE OSTI2023

Quantum Dots on Silicon-on-Insulator (QD/SOI): Nanoscale Strain and Band Structure Engineering (Final Report)

As the project titles indicate, the work focused on Group IV nanomembranes (NMs), thin functional layers, and interfaces, all with one or more dimensions at the nanoscale. The primary focus was discovery driven fundamental science. This approach led to surprising new, unexpected results that ended up being patentable and creating commercial value, but that were also high-impact science. Our effort divided into several overlapping thrusts: 1) strain engineering of NMs, via both lattice strain and externally applied strain, 2) interfaces between crystalline semiconductor NMs and other 2D sheets that are stacked or grown on each other, and 3) charge transport (electronics and optoelectronics) in thin layers, sheets, and surfaces. We accomplish these goals via 1) fabrication of new or higher-quality materials using NM approaches, 2) growth of new combinations, or 3) transfer and stacking to create new composites. The range of materials included combinations of Si, Ge, graphene, and several III-V compounds. The work has foundations in both nano- and mesoscale science.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Climatic controls on erosional efficiency vary with lithology across the Himalaya

Although climate can strongly influence erosional efficiency (i.e., erosion rate for a given topography), demonstrating its impact in tectonically active areas has been challenging due to other confounding controlling factors, such as lithology. Here, we show that 10 Be-derived erosion rates and efficiencies in the Himalayan orogen exhibit distinct relationships with climatic factors depending on lithology. We compile 173 10 Be-derived, basin-averaged erosion rates across the orogen, including 12 newly measured rates from the Dibang and Lohit valleys in the easternmost Himalaya, regions characterized by high precipitation magnitudes and variability. We group basins based on lithologies separated by orogen-scale thrust faults and quantify erosional efficiency coefficients based on the relationships between erosion rates and topographic metrics. Our results show that erosion rates and erosional efficiency from sedimentary and metasedimentary rocks along the Himalayan range front display a positive, nonlinear correlation with climatic factors, such as the number of extreme rainfall events and mean annual precipitation rates. In contrast, erosion rates from crystalline lithologies in the hanging wall of the Main Central thrust show a strong correlation with fluvial topography, whereas erosional efficiency shows no statistically significant correlation with climatic factors. Rapid erosion rates and high erosional efficiencies in the eastern Himalayan range front are likely driven by extreme precipitation on tectonically active, steep slopes composed of mechanically weak metasedimentary rocks. Our findings highlight the importance of the interplay between controlling factors, which include tectonics, lithology, and climate, that drive surface erosion and influence the topographic evolution of orogenic systems.

Channel steepness↗
DOE OSTI2024

Bringing randomized algorithms to mainstream numerical linear algebra

Numerical linear algebra (NLA) underpins huge swaths of computational science and engineering. For scientists and engineers to make the most of the DOE’s computing resources, it is essential that they have access to high-performance implementations of algorithms with best-in-class scalability and reliability. Despite this, prevailing NLA libraries have little to no support for breakthrough algorithms from the field of randomized numerical linear algebra (RandNLA) that have been developed over the past twenty years. The goal of this LDRD was to break a log-jam that had prevented broad adoption of RandNLA. Our work had two thrusts. The first was to develop RandBLAS: a trustworthy and high-performance C++ library for randomized dimension reduction (an operation widely known as sketching). The second was the development of a novel randomized algorithm for computing a challenging type of matrix decomposition known as Householder QR with column pivoting (Householder QRCP). In this one-year late-start LDRD we successfully delivered RandBLAS 1.0 and new CPU and GPU codes for Householder QRCP. RandBLAS has extensive documentation at https://randblas.readthedocs.io/en/stable/. Papers on RandBLAS and and our high-performance QRCP codes are forthcoming.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

A robust measure of event isotropy at colliders

We introduce a new event shape observable — event isotropy — that quantifies how close the radiation pattern of a collider event is to a uniform distribution. This observable is based on a normalized version of the energy mover’s distance, which is the minimum “work” needed to rearrange one radiation pattern into another of equal energy. We investigate the utility of event isotropy both at electron-positron colliders, where events are compared to a perfectly spherical radiation pattern, as well as at proton-proton colliders, where the natural comparison is to either cylindrical or ring-like patterns. Compared to traditional event shape observables like sphericity and thrust, event isotropy exhibits a larger dynamic range for high-multiplicity events. This enables event isotropy to not only distinguish between dijet and multijet processes but also separate uniform N-body phase space configurations for different values of N. As a key application of this new observable, we study its performance to characterize strongly-coupled new physics scenarios with isotropic collider signatures.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

WEST full tungsten operation with an ITER grade divertor

The mission of WEST (tungsten-W Environment in Steady-state Tokamak) is to explore long pulse operation in a full tungsten (W) environment for preparing next-step fusion devices (ITER and DEMO) with a focus on testing the ITER actively cooled W divertor in tokamak conditions. Following the successful completion of phase 1 (2016-2021), phase 2 started in December 2022 with the lower divertor made entirely of actively cooled ITER-grade tungsten mono-blocks. A boronization prior the first plasma attempt allowed for a smooth startup with the new divertor. Despite the reduced operating window due to tungsten, rapid progress has been made in long pulse operation, resulting in discharges with a pulse length of 100 s and an injected energy of around 300 MJ per discharge. Plasma startup studies were carried out with equatorial boron nitride limiters to compare them with tungsten limiters, while Ion Cyclotron Resonance Heating assisted startup was attempted. High fluence operation in attached regime, which was the main thrust of the first campaigns, already showed the progressive build up of deposits and appearance of dust, impacting the plasma operation as the plasma fluence increased. In total, the cumulated injected energy during the first campaigns reached 43 GJ and the cumulated plasma time exceeded 5 h. Demonstration of controlled X-Point Radiator regime is also reported, opening a promising route for investigating plasma exhaust and plasma-wall interaction issues in more detached regime. This paper summarises the lessons learned from the manufacturing and the first operation of the ITER-grade divertor, describing the progress achieved in optimising operation in a full W environment with a focus on long pulse operation and plasma wall interaction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Research on the Influence Mechanism of the High‐Steep Slope on the Deformation Characteristics of Bridge Substructure

With the development of the Chinese railway, the high‐steep slope is irreversible to be faced; especially under severe conditions such as heavy rainfall and earthquake, this kind of slope is prone to geological disasters, which seriously affects the safety and stability of the bridge substructure. Aiming to this, long‐term monitorization and numerical analysis were carried out in this research, and the influence mechanism of the high‐steep slopes on the stress and deformation characteristics of the bridge structure was studied. The research results show that under the effect of rainfall and earthquake, the original stress balance in the high‐steep slope is broken, and the possibility of landslide thrust increases; under the comprehensive impact of residual landslide thrust, traction force at slope foot, vertical gravity of bridge slab and vehicle, and the bridge cap will deform. Besides, the deformation of the bridge pier exceeds the allowable lateral displacement of the top of the bridge pier, reaching 111.7%∼112.4% of the limit, which seriously affects the stability of the bridge structure and the safety of the railway service. Therefore, by increasing the support strength of the slope foot and the diameter of the bridge pile foundation, the traction force of the slope foot can be reduced, and the sliding resistance of the bridge pile foundation can be improved so as the safety of the bridge structure can be promoted.

Zhang, Yufang (ORCID:0000000348912060)↗
DOE OSTI2025

High-Temperature Active Magnetic Bearing Development for Supercritical CO 2 Machinery Applications

Hermetic machinery utilizing gas bearings for MW-scale supercritical CO 2 (sCO 2 ) machinery applications can have significantly lower power loss and enable improved cycle efficiency compared to conventional machinery with oil-lubricated bearings. Active magnetic bearings (AMBs) are another option anticipated to have similar power loss and load capacity to gas bearings as well as offering larger mechanical tolerances, the ability to tune properties, and high reliability due to lack of mechanical wear. AMBs also have proven commercial experience at MW-scale, though environments for high-temperature sCO 2 power cycle machinery conditions are novel. Besides the potential impact of AMBs for sCO 2 turbomachinery, the technology also offers promising benefits for steam and gas turbines for power generation, compressors and expanders for industrial heat and power, and in other oil and gas and space applications. The goals of this project were to conceptual design an AMB and perform material testing. Conceptual designs for radial and thrust AMBs were produced based on a hermetically-sealed sCO 2 machinery waste-heat recovery (WHR) application for sizing and loads, and choosing a target design temperature of 540°C useful for high-temperature sCO 2 turbines for concentrating solar power (CSP) applications. Conceptual designs were initially developed for multiple radial and thrust AMBs with spreadsheet-based calculations before selecting one of each to develop further using higher-fidelity design methods for magnetic and structural performance. It was found that the radial AMB at 540°C was feasible, but the thrust AMB needed to be limited to 315°C for high-speed operation. The decision for a reduced-temperature thrust AMB was the result of several significant conclusions: 1) Hiperco 50A, originally chosen for good magnetic performance at high temperature, had insufficient strength for high-speed operation, so it was replaced with 17-4 PH. 2) The reduced magnetic performance from 17-4 PH yielded a larger bearing size, reducing the strength margin. 3) This ultimately led to a creative design implementing a more-compact E-core topology, compared to the original (conventional) C-core, and an integral shaft-disk with Hirth joint connection. These conceptual designs are unique for the size and temperature in CO 2 , relevant for MW-scale CSP applications. Long term, high temperature test data was generated for several materials, filling a void in the current body of literature. Corrosion and magnetic performance measurements were produced for PM materials (Alnico 5-7C, Alnico 9C, and SmCo) with and without nickel-coating for environments of high-temperature CO 2 up to 550°C at atmospheric pressure and 450°C at 103 bar for up to 6,000 hours. Corrosion measurements were also produced for Hiperco 50, a SM material relevant for AMB laminations, with and without C5 coating. Comparisons were also made for 450°C and 550°C, atmospheric pressure air exposures up to 5,000 hours. Results generally show that coatings can be effective at improving oxidation resistance of the bare materials, and Alnicos generally outperformed SmCo after high-temperature exposure. In addition to technical feasibility demonstrated by the design, economic feasibility was demonstrated by updating the TEA from the reference machine, re-evaluating it with CAPEX and OPEX to reflect estimated changes from process-lubricated bearings to AMBs. AMBs were shown to be comparable in performance to process-lubricated bearings, still showing a notable improvement over conventional machinery architecture with oil-lubricated bearings.

42 ENGINEERING↗
DOE OSTI2023

A National Infrastructure for Artificial Intelligence on the Grid (NI4AI) (Final Scientific/Technical Report)

Electric utilities have traditionally taken a very pragmatic yet myopic approach with grid sensors and the resulting collected data. Sensors are purchased and deployed to solve a specific, known problem that has risen to sufficient awareness as to justify the effort of deploying sensors and the needed capital investment. This sensor data flows into proprietary software packages with limited functionality intended only to address the initial problem. This approach aligns with the financial incentives of the utility to deploy capital into fixed hardware assets for which the corporations earn a rate of return. This mentality stands in stark contrast to the big data revolution that started nearly 25 years ago with the rise of Google. In this worldview, data is a fundamental business asset; successful organizations collect, store, explore, merge, and exploit as much data as possible to not only solve problems well understood today but also to tackle new problems that will inevitably rise tomorrow. The ARPA-E Open Innovation 2018 project entitled A National Infrastructure for Artificial Intelligence on the Grid or NI4AI for short was designed to demonstrate this alternative paradigm for using data. To do this, the project was composed of three key thrust areas. The first major component deployed a variety of high-frequency grid sensors and captured terabytes of both wide-scale and localized grid measurements, generating high-value datasets for grid research and algorithm development. The second aspect made available PingThings’ PredictiveGridTM, a horizontally scalable, cloud-based data management and AI platform built for time series data to explore and exploit the collected data. Finally, the project fostered a diverse and open research community composed of experts from numerous fields through focused educational content, code sharing, and data science competitions. Shifting away from “single use” sensors and closed data silos within electric utilities is a major benefit to the public at large. This legacy approach to data is incredibly (1) capital intensive (new sensors must be deployed for each new problem and problems tend to arise continuously) and (2) painfully slow (new problems must be identified first and then new sensors must be deployed to collect data to begin to address the issue). The transition to a carbon neutral grid requires a massive transformation of the existing grid infrastructure and will continue to challenge the legacy grid in unforeseen ways. The only way to make the energy transition cost effective is for utilities to abandon this dated data paradigm and adopt more contemporary approaches. NI4AI has shown that it is technically possible and economically feasible to ingest, explore, and exploit grid data collected from even very high frequency sensing, such as continuous point on wave sensors collecting measurements 10,000 times a second. In fact, the PredictiveGrid platform used is commercially available and deployed at several utilities in the United States. Project accomplishments were numerous and included (1) making available a state of the art time series platform to the community, (2) collecting over 520 streams of time series data from grid sensors totaling over 1 trillion grid measurements, and (3) developing and nurturing a community within the industry focused on the use of data to create value for utilities and, ultimately, end consumers.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Quantum annealing for jet clustering with thrust

Quantum computing holds the promise of substantially speeding up computationally expensive tasks, such as solving optimization problems over a large number of elements. In high-energy collider physics, quantum-assisted algorithms might accelerate the clustering of particles into jets. In this study, we benchmark quantum annealing strategies for jet clustering based on optimizing a quantity called “thrust” in electron-positron collision events. Here, we find that quantum annealing yields similar performance to exact classical approaches and classical heuristics, after tuning the annealing parameters. Without tuning, comparable performance can be obtained through a hybrid quantum/classical approach.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Large-Eddy Simulation of a wind turbine using a Filtered Actuator Line Model

When dealing with multirotor devices such as quadcopters or wind farms, the cost of blade-resolved large-eddy simulation (LES) becomes prohibitive. Combining LES with a family of lower-fidelity models, called actuator line models (ALMs), has grown in popularity in the past decade. ALM replaces full blade resolution with an array of actuator points or lines parameterized by aerodynamic lift/drag polar plots along the blades. Body forces computed based on these actuator points are then projected onto the LES flow mesh, mimicking the effect of rotating blades on the flow. However, the optimal projection radius and the associated LES grid size is often too restrictive for multirotor simulations. Recently, a new tip-correction-based filtered ALM (F-ALM) was proposed by Martinez-Tossas and Meneveau (2019), which allows coarser-than-optimal grids by avoiding the associated overprediction of thrust. In this work, F-ALM is implemented into a high-order, in-house LES code to simulate National Renewable Energy Laboratory Phase VI wind turbine. It is then followed by a comparison between the baseline ALM and the newly implemented F-ALM in terms of instantaneous and time-averaged flow fields and blade loads, revealing the advantages of F-ALM in preventing the overprediction of power on coarse grids. Finally, this encourages accurate and affordable simulations of multirotor devices in the future.

17 WIND ENERGY↗
DOE OSTI2021

Additively Manufactured Compliant Hybrid Gas Thrust Bearing for Supercritical Carbon Dioxide Turbomachinery: Design and Proof of Concept Testing

The following paper presents a new type of gas lubricated thrust bearing that utilizes additive manufacturing or also known as direct metal laser melting (DMLM) to fabricate the bearing. The motivation for the new bearing concept is derived from the need for highly efficient supercritical carbon dioxide (sCO2) turbomachinery in the mega-watt power range. The paper provides a review of existing gas thrust-bearing technology, outlines the need for the new DMLM concept, and discusses proof-of-concept testing results. The new concept combines hydrostatic pressurization with individual tilting pads that are flexibly mounted using hermetic squeeze film dampers (HSFD) in the bearing-pad support. This paper describes the thrust-bearing concept and discusses the final design approach. Proof-of-concept testing in air for a 6.8 in. (173 mm) outer diameter thrust gas bearing was performed; with thrust loading, up to 1500 lbs (6.67 kN) and a thrust runner speed of 10krpm (91 m/s tip speed). The experiments were performed with a bent shaft resulting in thrust runner axial vibration magnitudes of 2.9 mils (74 μm) p-p and dynamic thrust loads of 270 lbs (1.2 kN) p-p. In addition, force deflection characteristics and stiffness coefficients of the bearing system are presented for an inlet hydrostatic pressure of 380 psi (2.62 MPa). Results at 10 krpm show that the pad support architecture was able to sustain high levels of dynamic misalignment equaling 6 times the nominal film clearance while demonstrating a unit load-carrying capacity of 55 psi (0.34 Mpa). Gas-film force deflection tests portrayed nonlinear behavior like a hardening spring, while the bearing pad support stiffness was measured to be linear and independent of gas film thickness.

Engineering↗
DOE OSTI2023

Abbreviated Technical Report: Experimentally Interrogating Detonation Chemistry on Sub-Nanosecond to Nanosecond Timescales

Direct experimental measurement of chemical reactions during high explosive detonation remains challenging. Theory and modeling have long preceded experiment in the fundamental physical and chemical kinetic properties of detonation, and experimentation at the relevant timescales are needed to both validate models and provide fundamental understanding of detonation. In this LDRD-ER project, two approaches, x-ray diffraction and core-level x-ray Raman, were developed and used to further experimental capabilities to address this gap. We further developed dynamic x-ray diffraction to directly detect nanodiamond formation during detonation, providing experimental data towards resolving longstanding controversy in the scientific literature, and although the full kinetics have not yet been fully mapped, diamond diffraction appears on the same timescales as detonation soot formation. In the second research thrust, we have developed core-level x-ray Raman for use with high explosives. This technique provides information analogous to x-ray absorption spectroscopy and electron energy loss spectroscopy, but uses inelastic scattering of hard x-rays that can interrogate chemistry around light elements much deeper into the material. The low cross section and requisite high solid angle collection have hindered its use for ultra-fast spectroscopy. We developed and tested a high-q spectrometer which will substantially increase cross section and signal-to-noise, showing this method will also not dramatically alter, compared to x-ray absorption, the most discriminating spectral features of C, N, and O from various high explosives and expected detonation products. We have also used x-ray Raman combined with OCEAN electronic structure calculations to explore dynamic photodegradation mechanisms in PETN and CL-20 explosives. This provides a pathway towards implementing capability to dynamically explore chemistry at an x-ray free electron laser.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pulsed laser heating of diesel engine and turbojet combustor soot: Changes in nanostructure and implications

Here, carbonaceous particulate produced by a diesel engine and turbojet engine combustor are analyzed by transmission electron microscopy (TEM) for differences in nanostructure before and after pulsed laser annealing. Soot is examined between low/high diesel engine torque and low/high turbojet engine thrust. Small differences in nascent nanostructure are magnified by the action of high-temperature annealing induced by pulsed laser heating. Lamellae length distributions show occurrence of graphitization while tortuosity analyses reveal lamellae straightening. Differences in internal particle structure (hollow shells versus internal graphitic ribbons) are interpreted as due to higher internal sp3 and O-atom content under the higher power conditions with hypothesized greater turbulence and resulting partial premixing. TEM in concert with fringe analyses reveal that a similar degree of annealing occurs in the primary particles in soot from both diesel engine and turbojet engine combustors—despite the aggregate and primary size differences between these sources. Implications of these results for source identification of the combustion particulate and for laser-induced incandescence (LII) measurements of concentration are discussed with inter-instrument comparison of soot mass from both diesel and turbojet soot sources.

42 ENGINEERING↗
DOE OSTI2023

The Effects of Plasma Pre-Cracking on Drilling of Hard Rocks: A Single Insert Cutting Experiment

Abstract This paper studies the effects of plasma-induced cracks on rock cutting to support the concept of a plasma-integrated drag bit for accelerated geothermal drilling through hard rocks. For this, a single polycrystalline diamond compact (PDC) drilling technique is used in cutting granite to compare thrust and cutting forces between plasma-treated and untreated rock samples. The cracks are produced using underwater plasma at 80 J per pulse. This energy level does not produce visible damage to the rock. The cutting tests are conducted at a cutting speed of 12.7 m/min and four feed rates of 0.127, 0.201, 0.267, and 0.414 mm/s to represent actual drilling scenarios. The results show a general trend of reduction in both thrust and cutting forces for these feed rates, but the magnitude of reduction highly depends on the feed rate. The maximum force reduction of around 50% is found at the 0.267 mm/s feed rate with statistical significance. Cases with a higher force reduction are also found to have rougher surface topography, which indicates more excessive fracturing and, thus, a cracks-accelerated material removal process. This study provides initial evidence of using underwater plasma to increase the downhole drilling rate of hard rocks.

Engineering↗
DOE OSTI2020

CPAP Ventilators Needed for Rapid Response to COVID-19 by Modification of CPAP Equipment

Early on in the COVID-19 pandemic, potential ventilator shortages were a critical issue identified by national health care providers. Capacity modeling at the time suggested patient demand may exceed ventilator supply. Thus, the challenge became finding an urgent interim solution to meet health care needs. Our initial hypothesis was that CPAP technology could be modified to provide similar functionality to a ventilator, relieving demand and allowing physicians to decide which patients need high end machines, ultimately saving lives. In conjunction with medical experts and pulmonologists, we were able to identify three key thrusts associated with this research problem: (1) modification of CPAP technology to allow for 02 input that would be capable of providing ventilation; (2) development of an alarming function that would provide real-time audible alarms to alert medical personnel to critical conditions, which would be used inline with CPAP technology; and (3) a method of sterilizing expiratory air from such a system in order to protect medical personnel from biohazard, since CPAPs vent to the atmosphere. We were unable to realize results for thrust 1 (CPAP modification for 02); we identified potential safety issues associated with utilizing medical grade oxygen with a common CPAP device. In order to characterize and mitigate these issues, we would need to partner closely with a device manufacturer; such a partnership could not be achieved in the timeframe needed for this rapid response work. However, we determined that some medical grade BiPAP devices do not need this modification and that the significant progress on thrusts 2 and 3 would be sufficient to buy down risk of a massive ventilator shortage. Our team built a prototype alarm system that can be utilized with any assistive respiratory device to alert on all key conditions identified by medical personnel (high pressure, low pressure, apnea, loss of power, low battery). Finally, our team made significant progress in the rapid prototyping and demonstration of an inline UV air purifier device. The device is cost efficient and can be manufactured at scale with both commercially available and additively manufactured parts. Initial tests with SARS-CoV-2 analog bacteriophage MS2 show 99% efficacy at reducing bioburden. Following a successful demonstration of the prototype device with medical personnel, we were able to obtain follow-on (non-LDRD) funding to provide additional device characterization, validation, and production in order to respond to an immediate regional need.

42 ENGINEERING↗