Search NASA⌕ Search

SEARCH · Search NASA

Results for “HULLS - RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

The Effect of Spray Strips on a Model of the P3M-1 Flying Boat Hull

This note presents the results of a series of tests made in the N.A.C.A. tank on a one-sixth full-size model of the hull and side floats of the Navy P3M-1 flying boat for the purpose of finding a method of reducing the amount of spray thrown into the propellers of this craft when taking off and landing. The model was tested without spray strips and with five different spray-strip arrangements. The best arrangement was an improvement over the bare hull with no spray strips, but the improvement was not sufficient to be satisfactory with the propellers in the designed position.

Dawson, John R↗
NASA NTRS1947

A collection of the collapsed results of general tank tests of miscellaneous flying-boat-hull models

Presented here are the summary charts of the collapsed results of general tank tests of about 100 flying boat hull models. These summary charts are intended to be used as an engineering tool to enable a flying boat designer to grasp more quickly the significance of various hull form parameters as they influence his particular airplane. The form in which the charts are prepared is discussed in some detail in order to make them clearer to the designer. This is a data report, and no attempt has been made to produce conclusions or correlations of the usual sort. However, some generalizations are put forward on the various methods in which summary charts may be used.

Locke, F W S , Jr↗
NASA NTRS1927

Tests on airplane fuselages, floats and hulls

This report is a compilation of test data on airplane fuselages, nacelles, airship cars, seaplane floats, and seaplane hulls, prepared by the Bureau of Aeronautics, at the requests of the National Advisory Committee for Aeronautics. The discussion of the data includes the derivation of a scale correction curve to be used in obtaining the full scale drag. Composite curves of drag and L/D for floats and hulls are also given. (author)

Diehl, Walter S↗
NASA NTRS1934

Pressure-Distribution Measurements on the Hull and Fins of a 1/40-Scale Model of the U. S. Airship "Akron."

This report presents the results of measurements of pressure distribution conducted in the propeller-research wind tunnel of the National Advisory Committee for Aeronautics on a 1/40-scale model of the U. S. Airship "Akron" (ZRS-4). The pressures, which were measured simultaneously at nearly 400 orifices located at 26 stations along one side of the hull, were recorded by two photographic multiple manometers placed inside the model. The hull pressures were measured both with and without the tail surfaces and the control car for eight angles of pitch varying from 0 degree to 20 degrees and at air speeds of approximately 70 and 100 miles per hour. The pressures were also measured at approximately 160 orifices on one horizontal fin for the above speeds and pitch angles and for nine elevator angles.

Freeman, Hugh B↗
NASA NTRS1943

Aerodynamic and Hydrodynamic Tests of a Family of Models of Flying Hulls Derived from a Streamline Body -- NACA Model 84 Series

A series of related forms of flying-boat hulls representing various degrees of compromise between aerodynamic and hydrodynamic requirements was tested in Langley Tank No. 1 and in the Langley 8-foot high-speed tunnel. The purpose of the investigation was to provide information regarding the penalties in water performance resulting from further aerodynamic refinement and, as a corollary, to provide information regarding the penalties in range or payload resulting from the retention of certain desirable hydrodynamic characteristics. The information should form a basis for over-all improvements in hull form.

Parkinson, John B↗
NASA NTRS1942

The Longitudinal Stability of Flying Boats as Determined by Tests of Models in the NACA Tank II : Effect of Variations in Form of Hull on Longitudinal Stability

Data taken from tests at constant speed to establish trim limits of stability, tests at accelerated speeds to determine stable limits of center of gravity shift, and tests at decelerated speeds to obtain landing characteristics of several model hull forms were used to establish hull design effect on longitudinal stability of porpoising. Results show a reduction of dead rise angle as being the only investigated factor reducing low trim limit. Various methods of reducing afterbody interference increased upper trim limit

Olson, Roland E.↗
NASA NTRS1942

Strength Tests on Hulls and Floats

The present report deals with strength tests on hulls and floats intended in part for the collection of construction data for the design of these components and in part for the stress analysis of the finished hulls and floats.

Matthaes, K↗
NASA NTRS2003

The use of rice hulls for sustainable control of NOx emissions in deep space missions

The use of the activated carbon produced from rice hulls to control NOx emissions for future deep space missions has been demonstrated. The optimal carbonization temperature range was found to be between 600 and 750 degrees C. A burnoff of 61.8% was found at 700 degrees C in pyrolysis and 750 degrees C in activation. The BET surface area of the activated carbon from rice hulls was determined to be 172 m2/g when prepared at 700 degrees C. The presence of oxygen in flue gas is essential for effective adsorption of NO by activated carbon. On the contrary, water vapor inhibits the adsorption efficiency of NO. Consequently, water vapor in flue gas should be removed by drying agents before adsorption to ensure high NO adsorption efficiency. All of the NO in the flue gas was removed for more than 1.5 h when 10% oxygen was present and the ratio of the carbon weight to the flue gas flow rate (W/F) was 15.4 g min/L. Reduction of the adsorbed NO to form N2 could be effectively accomplished under anaerobic conditions at 550 degrees C. The adsorption capacity of NO on the activated carbon was found to be 5.02 mg of NO/g of carbon. The loss of carbon mass was determined to be about 0.16% of the activated carbon per cycle of regeneration if the regeneration occurred when the NO in the flue gas after the carbon bed reached 4.8 ppm, the space maximum allowable concentration. The reduction of the adsorbed NO also regenerated the activated carbon, and the regenerated activated carbon exhibited an improved NO adsorption efficiency.

NASA Program Advanced Human Support Technology↗
NASA NTRS1946

Waters Loads on the XJL-1 Hull as Obtained in Langley Impact Basin, TED No. NACA 2413.3

An investigation was conducted in the Langley impact basin of the water loads on a half scale model of the XJL-1 hull whose forebody has a vee bottom with exaggerated chine flare. The impact loads, moments, and pressures were determined for a range of landing conditions. A normal full-scale landing speed of 86 miles per hour was represented with effective flight paths ranging from 0.6deg to 11.6deg. Landings were made with both fixed trim and free-to-trim mounting of the float over a trim range of -15deg to 12deg into smooth water and into waves having equivalent full-scale length. of 120 feet and heights ranging from 1 to 4 feet. All data and results presented in this report are given in terms of equivalent full-scale values. Summary tables and illustrative plots are used in presenting the material. The following maximum values of load and pressure are those which are apropos for effective flight paths less than 6.5deg which was the maximum value obtained in tests with the XJL-1 hull model representing full-scale landings with vertical velocity of 4.5 feet per second into 4-foot waves. The maximum local pressure on the flat portion of the bottom is 130 pounds per square inch which was measured on a 2-inch-diameter circular area near the step. The maximum local pressure obtained in the curved area near the chines is 200 pounds per square inch. This pressure was also measured near the step.

Steiner, Margaret F.↗
NASA NTRS1926

Designing seaplane hulls and floats

Experimental data, such as the results of tank tests of models, render it possible to predict, at least in principle, as to how a hull or float of a given shape will comport itself. We will see further along, however, how uncertain these methods are and how they leave room for empiricism, which will reign for a long time yet in seaplane research bureaus.

FLOATS AND HULLS - DESIGN↗
NASA NTRS1979

The Aerodynamic Forces on Airship Hulls

The new method for making computations in connection with the study of rigid airships, which was used in the investigation of Navy's ZR-1 by the special subcommittee of the National Advisory Committee for Aeronautics appointed for this purpose is presented. The general theory of the air forces on airship hulls of the type mentioned is described and an attempt was made to develop the results from the very fundamentals of mechanics.

Munk, M. M.↗
NASA NTRS1988

Microstructure and growth model for rice-hull-derived SiC whiskers

The microstructure of silicon carbide whiskers grown from rice hulls has been studied using methods of high-resolution analytical electron microscopy. Small, partially crystalline inclusions (about 10 nm) containing calcium, manganese, and oxygen are concentrated in whisker core regions, while peripheral regions are generally inclusion free. The distinct microphase distribution is evidence of a two-stage growth process in which the core region grows first, followed by normal growth toward whisker sides. Partial dislocations extend radially from the core region to the surface and tend to be paired in V-shaped configurations. Whisker surfaces exhibit microroughness due to a tendency to develop small facets on close-packed planes. The microstructural data obtained from TEM observations are used as a basis for discussion of the mechanisms involved in whisker growth, and a model of the growth process is proposed. The model includes a two-dimensional growth mechanism involving vapor, liquid, and solid phases, although it is significantly different from the classical vapor-liquid-solid (VLS) process of whisker growth.

Nutt, Steven R.↗
NASA NTRS1993

Predicting multi-wall structural response to hypervelocity impact using the hull code

Previously, multi-wall structures have been analyzed extensively, primarily through experiment, as a means of increasing the meteoroid/space debris impact protection of spacecraft. As structural configurations become more varied, the number of tests required to characterize their response increases dramatically. As an alternative to experimental testing, numerical modeling of high-speed impact phenomena is often being used to predict the response of a variety of structural systems under different impact loading conditions. The results of comparing experimental tests to Hull Hydrodynamic Computer Code predictions are reported. Also, the results of a numerical parametric study of multi-wall structural response to hypervelocity cylindrical projectile impact are presented.

Schonberg, William P.↗