Search NASA⌕ Search

SEARCH · Search NASA

Results for “High-Lift flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

An analysis of thrust-induced effects on the longitudinal aerodynamics of STOL fighter configurations

An analysis of the thrust-induced longitudinal aerodynamic characteristics of three fighter-type configurations is presented. A brief discussion of the take-off and landing requirements for the next generation fighter aircraft leads to the conclusion that advances in lift coefficient and thrust reversing will be required to allow short-field operation. Typical power-on longitudinal aerodynamic data for the three fighter configurations, indicating different approaches to meeting the high-lift coefficient requirement, are discussed. Thrust reversing is not addressed in this paper. The power-on data are analyzed to determine what power effects are present, that is, direct thrust, boundary-layer control, vortex flows, or supercirculation. The results of the analysis indicate, for the configurations studied, that induced effects are small compared to direct thrust and that boundary-layer control, rather than leading-edge vortex flows or supercirculation, is the only significant thrust-induced effect.

Paulson, J. W., Jr.↗

Low-speed investigation of the maneuver capability of supersonic fighter wings

A low-speed investigation of wings suitable for supersonic fighter application was undertaken to understand the flow regions developed by these wings through flow visualization and to evaluate areas in which low-speed testing could provide information for extrapolation to higher Mach numbers and Reynolds numbers. This study involved cranked wings of highly-swept inboard panels and outboard panel of various sweeps with leading- and trailing-edge devices. Both theoretical and experimental results with flow visualization are presented. Flow visualization results show that a mixed flow condition (vortex flow on the highly-swept inboard section and attached flow on the cranked outboard section) is possible for wings with low sweep (20 deg) outboard cranked sections. Lift and drag measurements on the planar (no flap deflection) wings show good agreement with theoretical results for leading-edge vortex flow. There is little or no change in planar wing performance at maneuver conditions due to outboard sweep effects. Results also show that for cambered wings (flap deflected) only small improvements in performance over flat wings were obtained at high-lift maneuver conditions.

Hom, K. W.↗

Wind-tunnel Tests of a Hall High-life Wing

Wind-tunnel tests have been made to find the lift, drag, and center-of-pressure characteristics of a Hall high-lift wing model. The Hall wing is essentially a split-flap airfoil with an internal air passage. Air enters the passage through an opening in the lower surface somewhat back of and parallel to the leading edge, and flows out through an opening made by deflecting the rear portion of the under surface downward as a flap. For ordinary flight conditions the front opening and the rear flap can be closed, providing in effect a conventional airfoil (the Clark Y in this case). The tests were made with various flap settings and with the entrance to the passage both open and closed. The highest lift coefficient found, C(sub L) = 2.08, was obtained with the passage closed.

Weick, Fred E↗

Technology and operational considerations for low-heat-rate trajectories

A broad parametric study which examines several critical aspects of low-heat-rate entry trajectories is performed. Low planform loadings associated with future winged earth-entry vehicles coupled with the potential application of metallic thermal protection systems (TPS) suggest that such trajectories are of particular interest. Studied are three heating conditions - reference, stagnation, and windward centerline, for both laminar and turbulent flow; configuration-related factors including planform loading and hypersonic angle of attack; and mission-related factors such as cross-range and orbit inclination. Results indicate benefits in the design of TPS to be gained by utilizing moderate angles of attack as opposed to high-lift coefficient, high angles of attack, during entry. An assessment of design and technology implications is made.

Wurster, K. E.↗

Lattice arrangements for rapid convergence

A simple, systematic, optimized vortex-lattice approach is developed for application to lifting-surface problems. It affords a significant reduction in computational costs when compared to current methods. Extensive numerical experiments have been carried out on a wide variety of configurations, including wings with camber and single or multiple flaps, as well as high-lift jetflap systems. Rapid convergence as the number of spanwise or chordwise lattices are increased is assured, along with accurate answers. The results from this model should be useful not only in preliminary aircraft design but also, for example, as input for wake vortex roll-up studies and transonic flow calculations.

Hough, G. R.↗

Evaluation of laminar flow control systems for subsonic commercial transport aircraft: Executive summary

An evaluation was made of laminar flow control (LFC) system concepts for subsonic commercial transport aircraft. Configuration design studies, performance analyses, fabrication development, structural testing, wind tunnel testing, and contamination-avoidance techniques were included. As a result of trade studies, a configuration with LFC on the upper wing surface only, utilizing an electron beam-perforated suction surface, and employing a retractable high-lift shield for contamination avoidance, was selected as the most practical LFC system. The LFC aircraft was then compared with an advanced turbulent aircraft designed for the same mission. This comparison indicated significant fuel savings.

Pearce, W. E.↗

Low-speed wind-tunnel investigation of the longitudinal characteristics of a large-scale variable wing-sweep fighter model in the high-lift configuration

The low-speed characteristics of a large-scale model of the U. S. Navy/Grumman F-14A aircraft were studied in tests conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel. The primary purpose of the program was the determination of lift and stability levels and landing approach attitude of the aircraft in its high-lift configuration. Tests were conducted at wing angles of attack between minus 2 deg and 30 deg with zero yaw. Data were taken at Reynolds numbers ranging from 3.48 million to 9.64 million based on a wing mean aerodynamic chord of 7.36 ft. The model configuration was changed as required to show the effects of glove slat, wing slat leading-edge radius, cold flow ducting, flap deflection, direct lift control (spoilers), horizontal tail, speed brake, landing gear and missiles.

Eckert, W. T.↗

The Effect of Boundary-layer Control by Suction and of Several High-lift Devices on the Aerodynamic Characteristics in Yaw of a 47.5 Degree Sweptback

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5 and the airfoil sections normal to the quarter-chord line were NACA 61(sub 1)-A112. Tests included the plain wing and the wing with various combinations of extensible leading-edge and split flaps. The investigation was made to determine the effect of boundary-layer control by suction on the aerodynamic characteristics in yaw and on the effectiveness of a split-flap-type aileron for a range of angle of attack and suction-flow coefficient at a Reynolds number of 4.2 x 10 (exp 6) corresponding to a Mach number of approximately 0.07.

BOUNDARY LAYER - COMPLETE WINGS↗

Vortex-flow aerodynamics - An emerging design capability

Promising current theoretical and simulational developments in the field of leading edge vortex-generating delta, arrow ogival wings are reported, along with the history of theory and experiment leading to them. The effects of wing slenderness, leading edge nose radius, Mach number and incidence variations, and planform on the onset of vortex generation and redistribution of aerodynamic loads are considered. The range of design possibilities in this field are consequential for the future development of strategic aircraft, supersonic transports and commercial cargo aircraft which will possess low-speed, high-lift capability by virtue of leading edge vortex generation and control without recourse to heavy and expensive leading edge high-lift devices and compound airfoils. Attention is given to interactive graphics simulation devices recently developed.

Campbell, J. F.↗

Summary of Airfoil Data

Recent airfoil data for both flight and wind-tunnel tests have been collected and correlated insofar as possible. The flight data consist largely of drag measurements made by the wake-survey method. Most of the data on airfoil section characteristics were obtained in the Langley two-dimensional low-turbulence pressure tunnel. Detail data necessary for the application of NACA 6-serles airfoils to wing design are presented in supplementary figures, together with recent data for the NACA 24-, 44-, and 230-series airfoils. The general methods used to derive the basic thickness forms for NACA 6- and 7-series airfoils and their corresponding pressure distributions are presented. Data and methods are given for rapidly obtaining the approximate pressure distributions for NACA four-digit, five-digit, 6-, and 7-series airfoils. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed. The data indicate that the effects of surface condition on the lift and drag characteristics are at least as large as the effects of the airfoil shape and must be considered in airfoil selection and the prediction of wing characteristics. Airfoils permitting extensive laminar flow, such as the NACA 6-series airfoils, have much lower drag coefficients at high speed and cruising lift coefficients than earlier types-of airfoils if, and only if, the wing surfaces are sufficiently smooth and fair. The NACA 6-series airfoils also have favorable critical-speed characteristics and do not appear to present unusual problems associated with the application of high-lift and lateral-control devices. Much of the data given in the NACA Advance Confidential Report entitled "Preliminary Low-Drag-Airfoil and Flap Data from Tests at Large Reynolds Number and Low Turbulence," by Eastman N. Jacobs, Ira R. Abbott, and Milton Davidson, March 1942 has been corrected and included in the present paper, which supersedes the previously published paper.

LOW-DRAG↗

On the use of freon-12 for increasing Reynolds number in wind-tunnel testing of three dimensional aircraft models at subcritical and supercritical Mach numbers

The aerodynamic suitability of Freon-12 for general wind-tunnel testing was investigated at low and high subsonic speeds. Static aerodynamic characteristics of two transport airplane models were determined from strain gage balance measurements in both air and Freon-12 at several Reynolds numbers. A low-speed high-lift configuration was evaluated at Mach number 0.25, and a high-speed cruise wing-fuselage combination was tested at Mach numbers up to 0.825. The data obtained in air and in Freon-12 agree well, even in stalled flow, until compressibility effects evidently become significant in air and in Freon-12 agree well, even in stalled flow, until compressibility effects evidently become significant in air.

Treon, S. L.↗

Ground effect for V/STOL aircraft configurations and its simulation in the wind tunnel. Part 2: Experimental studies

Wind tunnel tests on a finite, knee-blowing-flapped wing and on a direct jet lift configuration were performed in a 30 x 42 inch wind tunnel. The objectives of these tests were, in experimental order:(1) to obtain definitive fixed-versus-moving ground comparisons on a powered, high-lift finite wing and on a lifting jet configuration as a function of model height and lift, (2) to understand the flow mechanism which lead to observed differences between moving and fixed-ground results, (3) to discover whether the above effects of a moving ground plane can be simulated by tangential-blowing boundary layer control at the wind tunnel floor, and (4) to check the form and the numerical constants for the wall jet blowing equation derived theoretically in Part I of this report. This relates wall jet blowing quantities to model lift coefficient.

Hackett, J. E.↗

Low-speed aerodynamic characteristics of a 13.1-percent-thick, high-lift airfoil

Experimental study of the low-speed, sectional characteristics of a high-lift airfoil, and comparison of these characteristics with the predictions of the theoretical methods used in the airfoil's design. The 13.1% thick UI-1720 airfoil was found to achieve the predicted maximum lift coefficient of nearly 2.0. No upper-surface flow separation was found below the stall angle of attack of 16 deg; it appeared that stall was due to an abrupt leading-edge flow separation.

Sivier, K. R.↗

Low-speed aerodynamic characteristics of a 13.1-percent-thick, high-lift airfoil

Low speed sectional characteristics of a high lift airfoil are studied and a comparison is made of those characteristics with the predictions of the theoretical methods used in the airfoil's design. The 13.1 percent-thick, UI-1720 airfoil was found to achieve the predicted maximum lift coefficient of nearly 2.0. No upper-surface, flow separation was found below the stall angle of attack of 16 degrees; it appeared that stall was due to an abrupt leading edge flow separation.

Sivier, K. R.↗

Two-dimensional wind-tunnel tests of a NASA supercritical airfoil with various high-lift systems. Volume 2: Test data

Three high lift systems for a 9.3 percent blunt based, supercritical airfoil were designed, fabricated, and wind tunnel tested. A method for calculating the viscous flow about two dimensional multicomponent airfoils was evaluated by comparing its predictions with test data. A comparison of high lift systems derived from supercritical airfoils with high lift systems derived from conventional airfoils is presented. The high lift systems for the supercritical airfoil were designed to achieve maximum lift and consisted of: (1) a single slotted flap, (2) a double slotted flap and a leading edge slat, and (3) a triple slotted flap and a leading edge slat. Aerodynamic force and moment data and surface pressure data are presented for all configurations and boundary layer and wake profiles for the single slotted flap configuration. The wind-tunnel models, test facilities and instrumentation, and data reduction are described.

Omar, E.↗

Advanced Aerodynamics. Selected NASA Research

This Conference Publication contains selected NASA papers that were presented at the Fifth Annual Status Review of the NASA Aircraft Energy Efficiency (ACEE) Energy Efficient Transport (EET) Program held at Dryden Flight Research Center in Edwards, California on September 14 to 15, 1981. These papers describe the status of several NASA in-house research activities in the areas of advanced turboprops, natural laminar flow, oscillating control surfaces, high-Reynolds-number airfoil tests, high-lift technology, and theoretical design techniques.

Source record↗

A Method for Predicting Lift Increments Due to Flap Deflection at Low Angles of Attack in Incompressible Flow

A method is presented for estimating the lift due to flap deflection at low angles of attack in incompressible flow. In this method provision is made for the use of incremental section-lift data for estimating the effectiveness of high-lift flaps. The method is applicable to swept wings of any aspect ratio or taper ratio. The present method differs from other current methods mainly in its ease of application and its more general application. Also included is a simplified method of estimating the lift-curve slope throughout the subsonic speed range.

WINGS, COMPLETE - TAPER AND TWIST↗