Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hover Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Rotor Hover Performance and Flowfield Measurements with Untwisted and Highly-Twisted Blades

The flowfield and performance characteristics of highly-twisted blades were analyzed at various thrust conditions to improve the fundamental understanding relating the wake effects on rotor performance. Similar measurements made using untwisted blades served as the baseline case. Twisted blades are known to give better hover performance than untwisted blades at high thrust coefficients typical of those found in full-scale rotors. However, the present experiments were conducted at sufficiently low thrust (beginning from zero thrust), where the untwisted blades showed identical, if not better, performance when compared with the highly-twisted blades. The flowfield measurements showed some key wake differences between the two rotors, as well. These observations when combined with simple blade element momentum theory (also called annular disk momentum theory) helped further the understanding of rotor performance characteristics.

Ramasamy, Manikandan↗
NASA NTRS1990

Model tilt-rotor hover performance and surface pressure measurement

A test of a small scale 3-bladed model rotor, with geometry typical of that used on tilt rotor aircraft, was conducted in the Army Aeroflightdynamics Directorate's anechoic hover chamber. The purpose was to determine the hover performance of the rotor and investigate the pressure distributions on a blade at various collective pitch angles and tip speeds. The measured pressures indicate that the rotor did not stall for high collective pitch angles up to theta sub c = 25 deg. This is clearly a 3-D effect since 2-D theory predicts flow separation at these high angles. The flow near the trailing edge separated above theta sub c = 25 deg which caused a sharp increase in power.

Tung, Chee↗
NASA NTRS1992

Hover performance validation of an ejector configured STOVL fighter aircraft

The hover thrust performance of a full-scale model of an ejector-lift/vectored thrust Short Take-Off and Vertical Landing (STOVL) fighter configuration was measured at the Outdoor Aerodynamic Research Facility of the National Full-Scale Aerodynamics Complex located at NASA Ames Research Center. The static thrust of the lifting ejector and ventral nozzle was calibrated at an out-of-ground-effect height. The test permitted comparison with static thrust calibrations obtained in the 80- by 120-Foot Wind Tunnel. The average static thrust augmentation ratio of the ejector system was 1.55 compared with the design goal of 1.63. The outdoor test showed that the addition of short extensions to the diffuser on the fuselage sidewall decreased suckdown and increased ejector performance. As expected, an increase in the ventral nozzle thrust deflection angle from nearly horizontal to the vertical-lift hover position caused a significant decrease in thrust. Flow visualization using smoke revealed greater secondary airflow into the left ejector and the penetration of hot ventral gases along the ground beneath and between the cool plumes from the ejector system.

Naumowicz, Tim↗
NASA NTRSDate not supplied

Overview of Rotor Hover Performance Capabilities at Low Reynolds Number for Mars Exploration

The Evolutionary aLgorithm for Iterative Studies of Aeromechanics (ELISA) software was developed in support of the Rotorcraft Optimization for the Advancement of Mars eXploration (ROAMX) project. ELISA was developed to enable aerodynamic rotor hover optimization for low Reynolds number flows in the Mars atmosphere. ELISA comprises two modules. The first module is dedicated to airfoil optimization and allows for the creation of multi-objective Pareto optimal (PO) airfoil sets with the airfoil performance evaluation performed using OVERFLOW. The second module is dedicated to rotor hover performance optimization and generates multi-objective PO rotor sets with the rotor performance evaluation performed using the comprehensive analysis code CAMRAD II. This paper presents recent updates to the ELISA optimization toolset. The airfoil module now includes variation in section Reynolds number, alongside simultaneous maximization of section lift and minimization of section drag. Consequently, the rotor optimization module can query PO airfoil sets (as a function of section lift, drag, and Reynolds number) and generate PO C81 decks tailored to specific Reynolds numbers, eliminating the need for adequate initial chord guesses and allowing for arbitrary rotor solidities to be studied. Furthermore, the rotor optimization has been extended to incorporate a third dimension, alongside maximization of blade loading and minimization of rotor power. This enables optimization across a relevant density range on Mars, presenting the lowest power rotor hover geometry, for each attainable blade loading, for each density. The goal of this work is to present the relevance of recent updates to the ELISA optimization toolset, by showing full rotor hover optimization using unconventional airfoils across a practical Mars density range, and by presenting various optimizations for changing blade numbers with unconstrained solidity in the Mars atmosphere.

Rotor↗
NASA NTRS1988

Effect of advanced rotorcraft airfoil sections on the hover performance of a small-scale rotor model

A hover test was conducted on a small scale rotor model for two sets of tapered rotor blades. The baseline rotor blade set used a NACA 0012 airfoil section, whereas the second rotor blade set had advanced rotorcraft airfoils distributed along the radius. The experiment was conducted for a range of thrust coefficients and tip speeds, and the data were compared to the predictions of three analytical methods. The data show the advantage of the advanced airfoils at the higher rotor thrust levels; two of the analyses predicted the correct data trends.

Althoff, Susan L.↗
NASA NTRS2016

Wind Tunnel and Hover Performance Test Results for Multicopter UAS Vehicles

There is currently a lack of published data for the performance of multicopter unmanned aircraft system (UAS) vehicles, such as quadcopters and octocopters, often referred to collectively as drones. With the rapidly increasing popularity of multicopter UAS, there is interest in better characterizing the performance of this type of aircraft. By studying the performance of currently available vehicles, it will be possible to develop models for vehicles at this scale that can accurately predict performance and model trajectories. This paper describes a wind tunnel test that was recently performed in the U.S. Army's 7- by 10-ft Wind Tunnel at NASA Ames Research Center. During this wind tunnel entry, five multicopter UAS vehicles were tested to determine forces and moments as well as electrical power as a function of wind speed, rotor speed, and vehicle attitude. The test is described here in detail, and a selection of the key results from the test is presented.

Multicopter UAS↗
NASA NTRS1992

Hover performance analysis of advanced rotor blades

This is an effort aimed at validating recent hover prediction methods. The experimental basis for this validation work is an extensive set of loads, wake and performance data, which were obtained from a pressure instrumented model UH-60 rotor tested at the Sikorsky hover test facility and at Duits-Nederlandse Windtunnel (DNW). This model was equipped with replaceable tips - including a tapered and a BERP-type tip - which permitted studies of the effects of rotor geometry. The central prediction method studied is a free-wake, vortex embedded, full-potential CFD method - called HELIX-I. It is found that the HELIX-I code produces very good comparisons with the data including wake, surface pressure and performance. Comparisons with the measured radial load distributions have permitted an improved understanding of the wake resolution modelling requirements of CFD methods. Since HELIX-I is a combined Eulerian/Lagrangian method, limited comparisons are also made with a Lagrangian boundary element code (called EHPIC) and an Eulerian Navier-Stokes code (called TURNS). In most cases all methods produce good comparisons with the data. It is found that the HELIX-I code provides a good compromise between the speed of boundary integral methods and the comprehensive nature of Navier-Stokes methods.

Tung, C.↗
NASA NTRSDate not supplied

ELISA: A Tool for Optimization of Rotor Hover Performance at Low Reynolds Number in the Mars Atmosphere

The Evolutionary aLgorithm for Iterative Studies of Aeromechanics (ELISA) was developed in support of the Rotorcraft Optimization for the Advancement of Mars eXploration (ROAMX) project. ELISA was developed to enable aerodynamic rotor hover optimization for low Reynolds number flows in the Mars atmosphere. The first objective of the algorithm allows for unconventional airfoil parameterization and multi-objective airfoil geometry optimization using OVERFLOW. The Pareto-optimal airfoil sets are converted to a set of Pareto-optimal airfoil decks, providing the lowest drag air foil geometry for each angle of attack, removing the need to arbitrarily select the airfoils to be used in the rotor optimization. The second objective allows for rotor geometry optimization with simultaneous maximization of blade loading and minimization of rotor power using the comprehensive analysis CAMRADII. The result is a Pareto-optimal rotor set, providing the lowest power rotor for each attainable blade loading, and one of the first tools for hover-optimized rotors for high-subsonic low Reynolds number conditions. The airfoil thickness can be modified after the airfoil optimization is complete, allowing for a post-airfoil-optimization adjustment of blade thickness to facilitate conforming to external structural analyses requirements. The relevance of the code is demonstrated with case studies for the ROAMX rotor optimization for Ingenuity-sized single rotors in the Mars atmosphere, a performance study optimizing the chord and twist of Ingenuity’s coaxial rotor resulting in the Sample Recovery Helicopters candidate rotor, and high-subsonic low Reynolds number airfoil optimization providing novel insights for higher-efficiency low Reynolds number airfoil geometries and flow physics.

ELISA↗
NASA NTRS1990

Free wake analysis of hover performance using a new influence coefficient method

A new approach to the prediction of helicopter rotor performance using a free wake analysis was developed. This new method uses a relaxation process that does not suffer from the convergence problems associated with previous time marching simulations. This wake relaxation procedure was coupled to a vortex-lattice, lifting surface loads analysis to produce a novel, self contained performance prediction code: EHPIC (Evaluation of Helicopter Performance using Influence Coefficients). The major technical features of the EHPIC code are described and a substantial amount of background information on the capabilities and proper operation of the code is supplied. Sample problems were undertaken to demonstrate the robustness and flexibility of the basic approach. Also, a performance correlation study was carried out to establish the breadth of applicability of the code, with very favorable results.

Quackenbush, Todd R.↗
NASA NTRS1954

Hovering Performance of a Helicopter Rotor Using NACA 8-H-12 Airfoil Sections

A helicopter rotor employing an NACA 8-H-12 airfoil section has been tested on the Langley helicopter test tower. Two blade surface conditions were investigated, first with a filled blade which was within 0.002 inch of true airfoil shape obtained by use of plastic filler, and second with the filler removed resulting in a surface condition within 0.020 inch of true airfoil shape. Tests were conducted for the two sur-face conditions at a tip speed of 455 feet per second and over a tip-speed range from 455 to 650 feet per second for the blades with filler removed. The NACA 8-H-12 blades with the filled surface showed an aver-age reduction of 6 to 7 percent in total torque coefficients.

Robert D Powell, Jr↗
NASA NTRS1972

Optimum performance of hovering rotors

A theory for the optimum performance of a rotor hovering out of ground effect is developed. The performance problem is formulated using general momentum theory for an infinitely bladed rotor, and the effect of a finite number of blades is estimated. The analysis takes advantage of the fact that a simple relation exists between the radial distributions of static pressure and angular velocity in the ultimate wake, far downstream of the rotor, since the radial velocity vanishes there. This relation permits the establishment of an optimum performance criterion in terms of the ultimate wake velocities by introducing a small local perturbation of the rotational velocity and requiring the resulting ratio of thrust and power changes to be independent of the radial location of the perturbation. This analysis fully accounts for the changes in static pressure distribution and axial velocity distribution throughout the wake as the result of the local perturbation of the rotational velocity component.

Wu, J. C.↗