Search NASA⌕ Search

SEARCH · Search NASA

Results for “INDENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

In Situ Nano-Indentation of a Gold Sub-Micrometric Particle Imaged by Multi-Wavelength Bragg Coherent X-ray Diffraction

The microstructure of a sub-micrometric gold crystal during nanoindentation is visualized by in situ multi-wavelength Bragg coherent X-ray diffraction imaging. The gold crystal is indented using a custom-built atomic force microscope. A band of deformation attributed to a shear band oriented along the (221) lattice plane is nucleated at the lower left corner of the crystal and propagates towards the crystal center with increasing applied mechanical load. After complete unloading, an almost strain-free and defect-free crystal is left behind, demonstrating a pseudo-elastic behavior that can only be studied by in situ imaging while it is invisible to ex situ examinations. The recovery is probably associated with reversible dislocations nucleation/annihilation at the side surface of the particle and at the particle-substrate interface, a behavior that has been predicted by atomistic simulations. The full recovery of the particle upon unloading sheds new light on extraordinary mechanical properties of metal nanoparticles obtained by solid-state dewetting.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Observation and Modeling of the Thermal Runaway of High-Capacity Pouch Cells Due to an Internal Short Induced by an Indenter

Owing to the complexity of coupling mechanical and electrical solvers for finite element analysis (FEA) of mechanical abuse of a battery, the simulation should be performed by incorporating a local short circuit model activated based on the status of battery elements. However, the approach should also consider various other conditions of the battery simulated, such as the initial state of charge (SOC), for precise simulations of the internal short. This study proposes an approach developed with a mechanical model and single-particle battery model, along with a reaction kinetics model for thermal abuse using LS-DYNA. Several key parameters were selected, such as the activation criteria, kinetic abuse and element integration points during the internal short circuit induced by the indenter. The impact of these key parameters in the FEA on thermal runaway response for various initial SOCs from 25 to 100 % were analyzed. The FEA results obtained were compared against experimental results with various parameters such as activation criterion of internal short, kinetic abuse based on accelerating rate calorimetry (ARC) data. Finally, the root causes of the discrepancy between the FEA and experimental results are discussed regarding integration point what solver can make difference during calculation.

ENERGY STORAGE↗
DOE OSTI2022

Indentation investigation of 304L stainless steel friction stir weld simulated crack repair

Simulated cracks were repaired in 304L stainless steel using low temperature friction stir welding. Indentation studies were carried out to understand the effect of microstructural features on the mechanical property variation across the weld and to measure the size of the weld zones with a quantitative technique. Microhardness and nanoindentation hardness profiles were constructed on a transverse section across the weld. The data obtained were correlated by extrapolating the nanoindentation hardness to greater depths which showed that the nanoindentation hardness closely reflects the microhardness values throughout the weld. Finally, grain size in the stir zone (SZ) was found to vary with the tool temperature which, in turn, alters the nanoindentation modulus variability and higher tool temperature resulted in widening of the SZ.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Initial development of a method for correlating indentation test results to damage accumulation in high temperature structural materials

This report describes an experimental approach based on microindentation creep or relaxation tests for assessing the remaining creep life of a sample material. The objective for this experimental program is to complement the development of passively loaded in situ surveillance specimens. These surveillance specimens could be placed in future advanced reactors to assess the degradation of structural properties, primary creep and creep-fatigue life, when the material is exposed to actual reactor operating conditions. The specimens and the corresponding indentation test protocol could form the basis of a structural health monitoring program designed to ensure the safe continued operation of the component given the relatively unknown effect of the reactor coolant chemistry, radiation exposure, and other environmental effects on the material properties of the constituent structural materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Microstructure and Temperature Dependent Indentation Response of Additively Manufactured Precipitation-Strengthened Al 0.3 Ti 0.2 Co 0.7 CrFeNi 1.7 High Entropy Alloy

The temperature-dependent [from room temperature (RT) to 500°C] nanoindentation behavior of a precipitation-strengthened Al 0.3 Ti 0.2 Co 0.7 CrFeNi 1.7 high-entropy alloy (HEA) processed via two different additive manufacturing (AM) techniques was investigated in the as-deposited and annealed conditions. The hierarchically heterogeneous microstructures were achieved via simple one-step annealing treatments, exploiting the residual stresses in the AM-processed HEA to partially recrystallize the microstructure, performed remarkably better than the nearly homogeneous microstructures in the as-deposited state. Further, the one-step annealed conditions revealed < 6.6% reduction in hardness values at 500°C compared to RT, while the as-deposited conditions showed a > 18% reduction in the hardness. The one-step annealed conditions also exhibited significantly higher hardness than the as-deposited conditions owing to their L1 2 -strengthened FCC microstructures. Furthermore, serrated yielding or the Portevin-Le Chatlier effect indicative of microstructural instability was observed during nanoindentation deformation (at 500°C) for the as-deposited conditions but not for the one-step annealed conditions. This, therefore, signifies the robustness of the hierarchically heterogeneous microstructures at elevated temperatures presenting a strong avenue for tuning the HEAs for future nuclear reactor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Preferred orientation of calcium aluminosilicate hydrate compacts: Implications for creep and indentation

Nano/micro-indentation has been extensively used to examine elastic properties and creep of cement-based materials. However, there have been inconsistencies in the measured elastic moduli and debate on the creep mechanism of calcium (alumino) silicate hydrates (C-(A-)S-H). To bring new insights, we examined the deviatoric stress-induced preferred orientation of calcium aluminosilicate hydrate (C-A-S-H), portlandite, and ettringite compacts, using synchrotron-based X-ray diffraction. Intense preferred orientations were observed in C-A-S-H compacts, and the c-axis of unit cells is highly aligned with the compression direction; weaker c-axis related fiber-type texture formed in portlandite and ettringite. Higher humidity, greater compacting pressure, and/or increased duration of the pressure intensified the C-A-S-H preferred orientation, which is facilitated by gel-pore water lubrication. This pressure-induced time-dependent preferential re-orientation of crystallites can contribute to the creep of cement-based materials, and it may cause overrepresentation of the soft c-axis of C-(A-)S-H unit-cell in nanoindentation experiments and underestimation of Young's modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Proppant embedment in coal and shale: Impacts of stress hardening and sorption

During methane production in CBM reservoirs, the influence of proppant embedment and permeability damage cannot be neglected – especially where the wall-rock is soft. Effective stresses are elevated during methane recovery, increasing both normal loading stress and confinement and simultaneously overprinting sorption-induced volumetric strains. Experiments and analytic modeling are conducted to define key mechanisms controlling these competitive effects. We independently measure overall sample compaction (external LVDT) and local strain (strain gauge) in the matrix to deconvolve proppant embedment in a propped fracture for different conditions of confining stress. The results show symptomatic behaviors of elastic (shale) and elastoplastic (coal) responses of embedment. Different from shale, the evolution of embedment is convex upwards with increased stress where indented depth increases more rapidly as loading stress increases under constant confinement. In addition, a stress-hardening effect is found to play a pivotal role in determining the characteristics of indentation, which are examined in terms of evolution profiles, deformation regimes, embedment slopes, curvatures, yield points and irreversible indentations. Based on the experimental observations a semianalytical model predicts indentation and the evolution of propped permeability under recreated in-situ stress conditions. A simplified case study is conducted to further illustrate the evolution of aperture and permeability of a propped fracture in CBM reservoirs. The modeling results suggest that proppant embedment is significantly overestimated if the variable stress-hardening (VSH) effect is neglected, especially when effective stress is large. Moreover, a decrease in indentation depth possibly occurs during late stage methane production, resulting in a reversal/recovery in fracture closure. This is because desorption-induced shrinkage becomes the predominant effect, causing an increase in aperture and a reduction in the indented volume of proppant. The resulting recovery in permeability implies that the propped coal fracture has the potential to optimally facilitate methane production as a pathway, even at high closure stresses generated by methane drainage.

01 COAL, LIGNITE, AND PEAT↗