SEARCH · Search NASA

Results for “ISO Standards”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Figures of Merit for Lunar Simulants

At an earlier SRR the concept for an international standard on Lunar regolith simulants was presented. The international standard, ISO 10788, Lunar Simulants, has recently been published. This paper presents the final content of the standard. Therefore, we are presenting an update of the following: The collection and analysis of lunar samples from 1969 to present has yielded large amounts of data. Published analyses give some idea of the complex nature of the regolith at all scales, rocks, soils and the smaller particulates commonly referred to as dust. Data recently acquired in support of NASA s simulant effort has markedly increased our knowledge and quantitatively demonstrates that complexity. It is anticipated that future analyses will further add to the known complexity. In an effort to communicate among the diverse technical communities performing research on or research using regolith samples and simulants, a set of Figures of Merit (FoM) have been devised. The objective is to allow consistent and concise comparative communication between researchers from multiple organizations and nations engaged in lunar exploration. This paper describes Figures of Merit in a new international standard for Lunar Simulants. The FoM methodology uses scientific understanding of the lunar samples to formulate parameters which are reproducibly quantifiable. Contaminants and impurities in the samples are also addressed.

Slane, Frederick A.↗

NASA NTRS2010

Electrostatic Discharge Test of Multi-Junction Solar Array Coupons After Combined Space Environmental Exposures

A set of multi-junction GaAs/Ge solar array test coupons were subjected to a sequence of 5-year increments of combined environmental exposure tests. The test coupons capture an integrated design intended for use in a geosynchronous (GEO) space environment. A key component of this test campaign is conducting electrostatic discharge (ESD) tests in the inverted gradient mode. The protocol of the ESD tests is based on the ISO/CD 11221, the ISO standard for ESD testing on solar array panels. This standard is currently in its final review with expected approval in 2010. The test schematic in the ISO reference has been modified with Space System/Loral designed circuitry to better simulate the on-orbit operational conditions of its solar array design. Part of the modified circuitry is to simulate a solar array panel coverglass flashover discharge. All solar array coupons used in the test campaign consist of 4 cells. The ESD tests are performed at the beginning of life (BOL) and at each 5-year environment exposure point. The environmental exposure sequence consists of UV radiation, electron/proton particle radiation, thermal cycling, and ion thruster plume. This paper discusses the coverglass flashover simulation, ESD test setup, and the importance of the electrical test design in simulating the on-orbit operational conditions. Results from 5th-year testing are compared to the baseline ESD characteristics determined at the BOL condition.

Wright, Kenneth H.↗

NASA NTRS1988

Data interfaces to the Space Station information system

The general form of the information system to be implemented to provide the broad and flexible services required to support the diverse needs of the U.S. Space Station is discussed. Emphasis is placed on the interfaces to the SSIS (Space Station Information System) and major interfaces within the SSIS. A central theme of the SSIS is the use of international standards, where appropriate and available. These standards include those of the International Organization for Standards (ISO), the Telegraph and Telephone Consultative Committee (CCITT), and the Consultative Committee for Space Data Systems (CCSDS). The specific standards selected or under consideration are enumerated. The effect of the selections on the interfaces visible to users of the SSIS are described, and a status report on the progress of official adoption of the standards is presented.

Carper, Richard↗

NASA NTRS2012

Providing Pressurized Gasses to the International Space Station (ISS): Developing a Composite Overwrapped Pressure Vessel (COPV) for the Safe Transport of Oxygen and Nitrogen

To supply oxygen and nitrogen to the International Space Station, a COPV tank is being developed to meet requirements beyond that which have been flown. In order to "Ship Full' and support compatibility with a range of launch site operations, the vessel was designed for certification to International Standards (ISO) that have a different approach than current NASA certification approaches. These requirements were in addition to existing NASA certification standards had to be met. Initial risk-reduction development tests have been successful. Qualification is in progress.

Kezirian, Michael↗

NASA NTRS1993

The standards process: X3 information processing systems

The topics are presented in viewgraph form and include the following: International Organization for Standards (ISO); International Electrotechnical Committee (IEC); ISO/IEC Joint Technical Committee 1 (JTC-1); U.S. interface to JTC-1; ANSI; national organizations; U.S. standards development processes; national and international standards developing organizations; regional organizations; and X3 information processing systems.

Emard, Jean-Paul↗

NASA NTRS1999

Status of WSTF Pyrovalve Handbook Development in Year 2000

Significant data have been generated through various spacecraft propulsion system projects involving the use of pyrotechnically operated valves (pyrovalves). These data need to be analyzed, interpreted, summarized, associated, and formatted so they can be made available for spacecraft propulsion system design involving pyrovalves and used to specify test procedures in the performance evaluation and qualification of these systems. To meet this need, a Pyrovalve Handbook is being developed at the NASA White Sands Test Facility. Standards of performance for pyrovalve applications are being formulated under the sponsorship of the NASA Technical Standards Program, as are pyrovalve testing standards under the sponsorship of the NASA Safety and Risk Management Program. The ultimate goal is to have the Handbook adopted as a voluntary standard under the guidance of the AIAA Energetic Components and Systems Technical Committee and, in a more restrictive format, become an integral part of ISO standards for Explosive Systems and Devices Used on Space Vehicles. Feedback from both Government and industry is encouraged and will be the focus of the presentation. It is especially critical that feedback be received on content and formatting of the Handbook to maximize benefit to the technical community. Submission of validated data from organizations outside of NASA is also encouraged.

Howard, Julien L.↗

NASA NTRS2009

Progress of the NASA/USGS Lunar Regolith Simulant Project

Beginning in 2004 personnel at MSFC began serious efforts to develop a new generation of lunar simulants. The first two products were a replication of the previous JSC-1 simulant under a contract to Orbitec and a major workshop in 2005 on future simulant development. Beginning in 2006 the project refocused its efforts and approached simulant development in a new and more comprehensive manner, examining new approaches in simulant development and ways to more accurately compare simulants to actual lunar materials. This led to a multi-year effort with five major tasks running in parallel. The five tasks are Requirements, Lunar Analysis, Process Development, Feed Stocks, and Standards. Major progress has been made in all five areas. A substantial draft of a formal requirements document now exists and has been largely stable since 2007. It does evolve as specific details of the standards and Lunar Analysis efforts proceed. Lunar Analysis has turned out to be vastly more difficult than anticipated. After great effort to mine existing published and gray literature, the team has realized the necessity of making new measurements of the Apollo samples, an effort that is currently in progress. Process development is substantially ahead of expectations in 2006. It is now practical to synthesize glasses of appropriate composition and purity. It is also possible to make agglutinate particles in significant quantities. A series of minerals commonly found on the Moon has been synthesized. Separation of mineral constituents from starting rock material is also proceeding. Customized grinding and mixing processes have been developed and tested are now being documented. Identification and development of appropriate feedstocks has been both easier and more difficult than anticipated. The Stillwater Mining Company, operating in the Stillwater layered mafic intrusive complex of Montana, has been an amazing resource for the project, but finding adequate sources for some of the components remains a difficult problem. For example the ratio of clino- to ortho-pyroxenes in the Stillwater is not an exact match for lunar materials. One of the sources being examined as an alternative pyroxene source is the Bushveld Complex in South Africa. Standards have been a major success for the project. The Figure of Merit algorithms have been created, tested, and are being considered for an ISO standard. Agreement has been reached in the community about how to make many of the critical measurements. There remains much work to do: (1) driving down the cost of simulants remains a major obstacle; (2) documentation and cost data analysis have not kept up with progress; (3) educating users in the complexity of the lunar regolith and the use of simulants remains a major task. In summary the project has made enormous progress and is successfully placing simulant development and use on a rigorous, scientifically defensible, engineering basis.

Rickman, Doug↗

NASA NTRS1997

Solar Cell Calibration and Measurement Techniques

The increasing complexity of space solar cells and the increasing international markets for both cells and arrays has resulted in workshops jointly sponsored by NASDA, ESA and NASA. These workshops are designed to obtain international agreement on standardized values for the AMO spectrum and constant, recommend laboratory measurement practices and establish a set of protocols for international comparison of laboratory measurements. A working draft of an ISO standard, WDI 5387, 'Requirements for Measurement and Calibration Procedures for Space Solar Cells' was discussed with a focus on the scope of the document, a definition of primary standard cell, and required error analysis for all measurement techniques. Working groups addressed the issues of Air Mass Zero (AMO) solar constant and spectrum, laboratory measurement techniques, and the international round robin methodology. A summary is presented of the current state of each area and the formulation of the ISO document.

Bailey, Sheila↗

NASA NTRS2004

Solar Cell Calibration and Measurement Techniques

The increasing complexity of space solar cells and the increasing international markets for both cells and arrays has resulted in workshops jointly sponsored by NASDA, ESA and NASA. These workshops are designed to obtain international agreement on standardized values for the AMO spectrum and constant, recommend laboratory measurement practices and establish a set of protocols for international comparison of laboratory measurements. A working draft of an ISO standard, WD15387, "Requirements for Measurement and Calibration Procedures for Space Solar Cells" was discussed with a focus on the scope of the document, a definition of primary standard cell, and required error analysis for all measurement techniques. Working groups addressed the issues of Air Mass Zero (AMO) solar constant and spectrum, laboratory measurement techniques, and te international round robin methodology. A summary is presented of the current state of each area and the formulation of the ISO document.

Bailey, Sheila↗

NASA NTRS2001

Status of Photovoltaic Calibration and Measurement Standards

The 7th International Workshop on Space Solar Cell Calibration and Measurement was held on September 25-27, 2000 in Girdwood, Alaska. Representatives from eight countries discussed international standards for single and multijunction solar cell measurement and calibration methods, round robin intercomparisons, and irradiation test methods for space solar cells. Progress toward adoption of an ISO standard on single junction cells was made. Agreement was reached to begin work on new standards for multijunction cells and irradiation testing. Progress on present single junction round robin measurements was discussed and future multijunction round robins were planned. The next workshop will be held in Germany in October 2001.

Baraona, Cosmo↗

NASA NTRS2018

The Evolution of the CCSDS Orbit Data Messages

The Consultative Committee for Space Data Systems (CCSDS) Orbit Data Messages (ODM) is undoubtedly the most successful and widely infused international standard developed by the CCSDS Navigation Working Group (NavWG). In 2004, the first version of the ODM was published after a development period of several years; before this, there was no CCSDS or ISO standard for the representation of a spacecraft trajectory. This paper will describe in detail the evolution of the CCSDS ODM through its several versions past, present, and future; its infusion into spacecraft operations in many if not most of the Earth's major space agencies; and some of the growing number of applications in which it is being utilized.

Oltrogge, Daniel L.↗

NASA NTRS1990

OSI in the NASA science internet: An analysis

The Open Systems Interconnection (OSI) protocol suite is a result of a world-wide effort to develop international standards for networking. OSI is formalized through the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). The goal of OSI is to provide interoperability between network products without relying on one particular vendor, and to do so on a multinational basis. The National Institute for Standards and Technology (NIST) has developed a Government OSI Profile (GOSIP) that specified a subset of the OSI protocols as a Federal Information Processing Standard (FIPS 146). GOSIP compatibility has been adopted as the direction for all U.S. government networks. OSI is extremely diverse, and therefore adherence to a profile will facilitate interoperability within OSI networks. All major computer vendors have indicated current or future support of GOSIP-compliant OSI protocols in their products. The NASA Science Internet (NSI) is an operational network, serving user requirements under NASA's Office of Space Science and Applications. NSI consists of the Space Physics Analysis Network (SPAN) that uses the DECnet protocols and the NASA Science Network (NSN) that uses TCP/IP protocols. The NSI Project Office is currently working on an OSI integration analysis and strategy. A long-term goal is to integrate SPAN and NSN into one unified network service, using a full OSI protocol suite, which will support the OSSA user community.

Nitzan, Rebecca↗

NASA NTRS2018

Developing a Standard for Earth Observation Data Preservation Content - A Path to Future Usability

For datasets to be usable, many pieces of information in addition to the data themselves are essential. During the active parts of the lifecycle of dataset generating projects, the needed information is usually accessible through individuals familiar with the various aspects of the projects. However, the utility of datasets tends to outlive the lives of projects, by several decades in many cases. Thus it is essential to capture all the relevant information about the datasets, data, metadata and associate knowledge that is sufficient to read, understand, interpret and reuse the datasets, while the projects are still active. The capture and preservation should be such that the data are usable when no consultation is available from the original project participants. Identification of specific categories of content through an international standard is beneficial to the user communities of the future, so that projects involving Earth observations and generating data products can consistently plan for preservation and future usability of the project outcomes. While there are existing standards that address archival and preservation in general, there are no existing international standards or specifications today to address what content should be preserved. The standard, ISO 19165-1, titled "Geographic Information - Preservation of digital data and metadata Part 1: Fundamentals" considers geographic information preservation in general. It acknowledges that "specific content items needed to preserve the full provenance and context of the data and associated metadata depend on the needs of the designated community and types of datasets (e.g., maps, remotely sensed data from satellites and airborne instruments, physical samples). Follow-up parts to this standard may be developed detailing content items appropriate to individual disciplines." NASA proposed an extension to this standard, titled "Geographic information -- Preservation of digital data and metadata -- Part 2: Content specifications for Earth observation data and derived digital products." The development of this extension is in progress with participation by an international team representing nine countries. The purpose of this paper is to introduce this standard and report on its status.

Remote Sensing; Data Systems; Open Data;↗

NASA NTRS1992

ACSYNT - A standards-based system for parametric, computer aided conceptual design of aircraft

A group of eight US aerospace companies together with several NASA and NAVY centers, led by NASA Ames Systems Analysis Branch, and Virginia Tech's CAD Laboratory agreed, through the assistance of Americal Technology Initiative, in 1990 to form the ACSYNT (Aircraft Synthesis) Institute. The Institute is supported by a Joint Sponsored Research Agreement to continue the research and development in computer aided conceptual design of aircraft initiated by NASA Ames Research Center and Virginia Tech's CAD Laboratory. The result of this collaboration, a feature-based, parametric computer aided aircraft conceptual design code called ACSYNT, is described. The code is based on analysis routines begun at NASA Ames in the early 1970's. ACSYNT's CAD system is based entirely on the ISO standard Programmer's Hierarchical Interactive Graphics System and is graphics-device independent. The code includes a highly interactive graphical user interface, automatically generated Hermite and B-Spline surface models, and shaded image displays. Numerous features to enhance aircraft conceptual design are described.

Jayaram, S.↗

NASA NTRS1975

Analysis of proposed criteria for human response to vibration

The development of criteria for human vibration response is reviewed, including the evolution of the ISO standard 2631. The document is analyzed to show why its application to vehicle ride evaluation is strongly opposed. Alternative vertical horizontal limits for comfort are recommended in the ground vehicle ride frequency range above 1 Hz. These values are derived by correlating the absorbed power findings of Pradko and Lee with other established criteria. Special emphasis is placed on working limits in the frequency range of 1 to 10 Hz since this is the most significant area in ground vehicle ride evaluation.

Janeway, R. N.↗

NASA NTRS1978

Effect of vibration duration on human discomfort

The duration effects of random vertical vibration on passenger discomfort were studied in a simulated section of an aircraft cabin configured to seat six persons in tourist-class style. Variables of the study included time of exposure (0.25 min to 60 min) and the rms amplitude of vibration (0.025g to 0.100g). The vibrations had a white noise spectrum with a bandwidth of 10 Hz centered at 5 Hz. Data indicate that the discomfort threshold occurred at an rms vertical acceleration level of 0.027g for all durations of vibration. However, for acceleration levels that exceeded the discomfort threshold, a systematic decrease in discomfort occurred as a function of increasing duration of vibration. For the range of accelerations used, the magnitude of the discomfort decrement was shown to be independent of acceleration level. The results suggest that discomfort from vertical vibration applied in the frequency range at which humans are most sensitive decreases with longer exposure, which is the opposite of the recommendation of the International Standard ISO 2631-1974 (E) Guide for the Evaluation of Human Exposure to Whole-Body Vibration.

Clevenson, S. A.↗

NASA NTRS1987

Media independent interface. Interface control document

A Media Independent Interface (MII) is specified, using current standards in the industry. The MII is described in hierarchical fashion. At the base are IEEE/International Standards Organization (ISO) documents (standards) which describe the functionality of the software modules or layers and their interconnection. These documents describe primitives which are to transcent the MII. The intent of the MII is to provide a universal interface to one or more Media Access Contols (MACs) for the Logical Link Controller and Station Manager. This interface includes both a standardized electrical and mechanical interface and a standardized functional specification which defines the services expected from the MAC.

Source record↗

NASA NTRS1988

Performance analysis of FDDI

The Fiber Distributed Data Interface (FDDI) is an imerging ANSI and ISO standard for a 100 megabit per second fiber optic token ring. The performance of the FDDI media access control protocol is analyzed using a simulation developed at NASA Ames. Both analyses using standard measures of performance (including average delay for asynchronous traffic, channel utilization, and transmission queue length) and analyses of characteristics of ring behavior which can be attributed to constraints imposed by the timed token protocol on token holding time (including bounded token rotation time, support for synchronous traffic, and fairness of channel access for nodes transmitting asynchronous traffic) are included.

Johnson, Marjory J.↗