SEARCH · Search NASA

Results for “Ice Adhesion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2021

An Investigation of the Grain Size and Adhesion Strength of High-Speed Impact Ice

Ice accumulation on aircraft from supercooled water droplets (impact icing) can increase drag and decrease lift, leading to a decrease in fuel efficiency and a potential for unsafe situations. Anti-icing materials and coatings are of high interest to prevent aircraft icing. Because no anti-icing material suitable for in-flight situations has been realized, icing models aim to predict the accumulation and shape of the ice to understand its effects. In both cases, understanding the physical mechanism behind ice adhesion and shedding is necessary. A recent literature review has shown that the apparent ice adhesion strength to any specific material varies over several orders of magnitude across studies and test methods. One of the reasons for this high variance is likely to be the varying microstructure of the ice used for different studies. Although the microstructure of impact ice has been studied in the past, those conditions were not relevant to that of in-flight aircraft icing. The microstructure of the ice formed will determine both its bulk and surface properties, yet it has been overlooked in the ice adhesion community. Here, we use optical microscopy to study the non-uniform ice crystal grain size in impact ice accreted in NASA Glenn Research Center’s Icing Research Tunnel at various icing conditions. Similar to other environmental conditions studied in the literature, we show an increase in grain size at larger distances from the growth interface; however, the data shows substantially larger grains than what was expected from the prior literature. Ice accrued at lower temperatures has a smaller grain size at all distances from the growth interface. No change in grain size was noticed when varying only the wind speed. A correlational analysis shows that smaller grain sizes at the growth interface corresponded to an increase in the apparent ice adhesion strength when the adhesive failure was interfacial, but not when the failure was cohesive. These results may explain the overall trend in the literature of increasing apparent adhesion strength with decreasing temperature. Incorporating microstructure trends for various environmental conditions in icing models may increase the certainty in predicting ice adhesion strength and shedding, and will provide a better basis for comparison between adhesive tests on ice produced in different facilities and at different storage times.

• Ice Fabric↗

NASA NTRS2014

Hydrogen-Bonding Surfaces for Ice Mitigation

Ice formation on aircraft, either on the ground or in-flight, is a major safety issue. While ground icing events occur predominantly during the winter months, in-flight icing can happen anytime during the year. The latter is more problematic since it could result in increased drag and loss of lift. Under a Phase I ARMD NARI Seedling Activity, coated aluminum surfaces possessing hydrogen-bonding groups were under investigation for mitigating ice formation. Hydroxyl and methyl terminated dimethylethoxysilanes were prepared via known chemistries and characterized by spectroscopic methods. These materials were subsequently used to coat aluminum surfaces. Surface compositions were based on pure hydroxyl and methyl terminated species as well as mixtures of the two. Coated surfaces were characterized by contact angle goniometry. Receding water contact angle data suggested several potential surfaces that may exhibit reduced ice adhesion. Qualitative icing experiments performed under representative environmental temperatures using supercooled distilled water delivered via spray coating were inconclusive. Molecular modeling studies suggested that chain mobility affected the interface between ice and the surface more than terminal group chemical composition. Chain mobility resulted from the creation of "pockets" of increased free volume for longer chains to occupy.

Smith, Joseph G., Jr.↗

NASA NTRS1989

Generic icing effects on forward flight performance of a model helicopter rotor

An experimental program using a commercially available model helicopter has been conducted in the TAMU 7 ft x 10 ft Subsonic Wind Tunnel to investigate main rotor performance degradation due to generic ice adhesion. Base and iced performance data were gathered as functions of fuselage incidence, blade collective pitch, main rotor rotational velocity, and freestream velocity. The experimental values have shown that, in general, the presence of generic ice introduces decrements in performance caused by leading edge separation regions and increased surface roughness. In addition to the expected changes in aerodynamic forces caused by variations in test Reynolds number, forward flight data seemed to be influenced by changes in freestream and rotational velocity. The dependence of the data upon such velocity variations was apparently enhanced by increases in blade chord.

Tinetti, Ana F.↗

NASA NTRSDate not supplied

NASA Icing Overview 2023

This presentation summarizes NASA icing research for an invited talk to be presented on June 22, 2023, at the SAE International Conference on Icing of Aircraft, Engines, and Structures. The presentation describes the NASA icing portfolio including facilities and computational tools. In addition, high-level summaries of NASA’s current icing research activities are provided. This includes: (1) Transonic Truss Brace Wing, (2) High Lift Common Research Model, (3) Advanced Air Mobility, (4) Characterization of Low Ice Adhesion Materials, (5) High Ice Water Content Flight Research, (6) Simulated Inter-compressor Duct Research Model, (7) Efficient Quiet Integrated Propulsor. Finally, the presentation summarizes collaboration and partnership opportunities with NASA.

Icing↗

NASA NTRSDate not supplied

The Measurement of Shear Strain in Impact Ice Using a Modified Lap Joint Test and Digital Image Correlation

The results of ice adhesion testing efforts are typically quantified using the maximum shear stress sustained at the interface before the ice detaches from the underlying substrate. While this singular value can be useful for understanding the role icing wind tunnel conditions and substrate surface properties have on the strength of the ice-substrate interface, it does not capture the mechanical behavior of the ice during an experiment. To better understand the deformation of the ice sample and ice-substrate interface during testing, digital image correlation was applied to the lap-joint shear test methodology utilized at NASA Glenn Research Center. Preparation of the sample surface for digital image correlation, initial parsing of the correlation data, and the time synchronization of data from multiple sources are discussed. Using the directional components of deformation measured via digital image correlation, a novel approach to calculating the interfacial shear strain is presented. Results from analyzing several impact ice samples consistently reveals a non-linear response in the ice during mechanical loading which occurs prior to sample delamination, a behavior not observable in the force and displacement data gathered from the testing apparatus. Both the full and small angle forms of the engineering shear strain are evaluated, with the full shear strain form providing considerably lower noise levels. The transition of sample response from near the interface to the bulk behavior of the ice under shear loading is discussed with results from several samples being presented.

Ice adhesion↗

NASA NTRSDate not supplied

The Measurement of Shear Strain in Impact Ice Using a Modified Lap Joint Test and Digital Image Correlation

: Ice Adhesion, Digital Image Correlation, Experim↗

NASA NTRS2018

Polymer-Filled Metal Foams for Contamination Resistant Aircraft Leading Edges

Adhesion of contaminants has been identified as a ubiquitous issue for aeronautic exterior surfaces. Organic coatings have been demonstrated to enable reduction in insect residue adhesion as well as a reduction in ice adhesion strength. These approaches however, have yet to demonstrate sufficient durability to enable application to commercial aircraft wing leading edges. High durability materials have been developed in parallel to these efforts; contaminant adhesion issues are not addressed. This work describes a first attempt to identify a solution to the seemingly competing issues of contaminant adhesion and durability. A co-continuous network of organic and metallic domains may provide greater durability, while still enabling the changes in surface-contaminant interactions that have been realized. To that end, unique properties have been achieved through fabrication of composite metal foam materials. Likewise, extensive research has been dedicated toward development of polymeric coatings for mitigation of insect residue adhesion.This work describes initial results from infusion of a low surface free energy epoxy resin into a composite metal foam substrate for the purpose of generating a durable contaminant adhesion-resistant material.

Robbins, Samuel J.↗

NASA NTRSDate not supplied

NASA Icing Research Update 2024

This presentation summarizes NASA’s current icing research portfolio for an invited talk on August 1, 2024, at the AIAA Aviation Forum and Exposition. The presentation overviews NASA facilities, computational tools, and latest research. This research is categorized as application focused research, atmospheric characterization, and fundamental research / capability improvement. The application focused research includes (1) the Transonic Truss Brace Wing, (2) High Lift Common Research Model, (3) Advanced Air Mobility, and (4) Efficient Quiet Integrated Propulsor. The atmospheric characterization work includes High Ice Water Content Flight Research, while the fundamental research / capability improvement area includes (1) the Simulated Inter-compressor Duct Research Model, (2) Characterization of Low Ice Adhesion Materials, (3) Collection Efficiency Measurements, (4) Impedance Based Ice/ Water Sensor, (5) Tomography for Cloud Uniformity in the Icing Research Tunnel, and (6) Supercooled Large Drop Research. Finally, the presentation summarizes collaboration and partnership opportunities with NASA.

Icing↗

NASA NTRSDate not supplied

NASA Icing Update – May 2024

This presentation provides a status update on select NASA icing research activities for the SAE AC-9C Icing Technical Committee Meeting on May 6, 2024. The updates include the following topics: (1) Propulsion Systems Lab (PSL), (2) Adaptive Icing Tunnel (AIT), (3) Ice Adhesion / Deformed Skin Adhesion Test, (4) GlennICE, (5) Efficient Quiet Integrated Propulsor, (6) Icing Research Tunnel (IRT) CFD Characterization, and (7) Supercooled Large Droplet (SLD) Research.

Icing↗

NASA NTRS2019

Incorporation of Functionalized Polyhedral Oligomeric Silsesquioxane Nanomaterials as Reinforcing Agents for Impact Ice Mitigating Coatings

In-flight, aircraft are exposed to a wide range of environments. One commonly exposed environment are clouds containing super-cooled water droplets. These water drop- lets exist in a metastable state below the freezing point of water, in the range of 0 to -20°C. As the vehicle impacts the droplets, latent heat is released and within milliseconds the droplets convert to ice. This process is referred to as impact icing or in-flight icing.1 Impact icing is a major concern for aircraft since it can lead to degraded aerodynamic performance and, if left un- treated, can lead to loss of the vehicle. Active approaches (i.e., pneumatic boots, heated air ducts) typically utilized in mitigating in-flight ice accretion significantly increases vehicle weight and cannot be applied to all aircraft.1-3 A passive approach based on coatings is desired, but durability issues are a concern, especially on the wing leading edge.3 Nanomaterials have been shown to afford significant improvement in coating and composite physical properties at low loading levels.4 In this study, Polyhedral Oligomeric Silsesquioxane (POSS) nanomaterials have been shown to increase coating durability. Also, with wide variety of functionalities present on the arm structure, POSS nanomaterials have been shown to readily alter coating surface chemistry to mitigate impact ice adhesion from -16 to -8°C in a simulated in-flight icing environment.

Beck, Devon M.↗

NASA NTRSDate not supplied

Designed Adhesion - Exploring the Unknown

The ability to design materials and substrates for adhesive properties is highly desirable for the aeronautics industry. This includes the ability to design substrates that have low ice adhesion to increase efficiency of the fleet, as well as the ability to design structural adhesives to improve manufacturing rate. The Designed Adhesion group was chosen during the 2023 Wicked Wild Pitch Event sponsored by CAS and is currently in the discovery phase.

Design↗

NASA NTRSDate not supplied

Idea Evolution ... What's Next?

No research project lasts forever. Even the most wildly successful programs will eventually come to an end. The challenge in that moment, when a project ends, is how to take what was learned in that project and apply it to the next research activity you undertake. Although not always possible, information and insights from a project that is underway or coming to a close can be leveraged to identify a new research direction and advance existing tangentially related activities. In this presentation, a common thread will be followed through a series of sequential research projects where lessons learned in each activity were built into the next enabling each new research project to advance further and faster. Initial research focused on lunar dust adhesion mitigation coalesced into two major contributors to adhesion interactions; which were, not surprisingly, surface chemistry and topography. This knowledge was applied to addressing insect residue adhesion mitigation on commercial aircraft leading edge surfaces. Composite epoxy coatings formulated with controlled surface chemistry and topography were evaluated and led to identification of additional relevant considerations: dynamics and surface morphology. Collectively, these considerations were applied to address impact ice adhesion mitigation where further properties were elucidated: surface mechanical properties and durability. Seeking commonality between these research endeavors led to greater understanding of each new research objective and ultimately, identification of robust, viable pathways toward meaningful results.

Adhesion Mitigation↗

NASA NTRS2019

Polymer Infused Composite Metal Foam as a Potential Aircraft Leading Edge Material

The leading edge of the aircraft wings must be free from three-dimensional disturbances caused by insect adhesion, ice accretion, and particle wear in order to improve flight performance, safety, and fuel efficiency of the aircraft. An innovative solution was explored in this work by infusing stainless steel composite metal foam (SS CMF) with a hydrophobic epoxy resin system. S-S CMF was made with 100% stainless steel using a powder metallurgy technique. The infused epoxy filled the macro- and microporosities, unique to SS CMF’s structure, creating a product with a density similar to that of aluminum. The contact angle, wear rate, erosion resistance, and insect adhesion of the novel infused composite metal foam were measured and compared to aluminum, epoxy and stainless steel. The infusion process was determined to fill up to 88% of the pores within the SS CMF and was found to reduce wettability and insect residue accretion. The contact angle of the infused SS CMF was 43% higher than its parent material, stainless steel, and 130% higher than aluminum. Insect residue maximum height and areal coverage were reduced by 60 and 30%, respectively, compared to aluminum. Grit blast experiments to simulate erosion resulted in a greater roughness increase for aluminum than for the parent epoxy resin or the resin-infused SS CMF. These results suggest that the durability and performance of infused SS CMF was superior compared to aluminum, which is the current leading edge material of choice. Based on the promising results under relevant wear and erosion conditions, it is concluded that the infused SS CMF can offer a potential tailored replacement to aluminum leading edge material.

Jacob C. Marx↗

NASA NTRS1998

NASA Lewis' Icing Research Tunnel Works With Small Local Company to Test Coatings

Dynamic Coatings, Inc., wanted to test coating products that would enable the company to approach new markets. A Space Act Agreement with NASA Lewis Research Center afforded them this opportunity. They used Lewis' Icing Research Tunnel to test coating products for reduced ice adhesion, industrial and aerospace lubrication applications, a tiremold release coating now used in the production of tires for the Boeing 777, and a product that solidifies asbestos fibers (which is being tested as an insulator in a power plant in Iowa). Not only was the testing a success, but during these activities, Dynamic Coatings met another coating company with whom they now have a joint venture offering a barnacle-repellent coating for marine applications, now on the market in Florida.

Source record↗

NASA NTRS2008

NASA Tech Briefs, October 2008

Topics covered include: Control Architecture for Robotic Agent Command and Sensing; Algorithm for Wavefront Sensing Using an Extended Scene; CO2 Sensors Based on Nanocrystalline SnO2 Doped with CuO; Improved Airborne System for Sensing Wildfires; VHF Wide-Band, Dual-Polarization Microstrip-Patch Antenna; Onboard Data Processor for Change-Detection Radar Imaging; Using LDPC Code Constraints to Aid Recovery of Symbol Timing; System for Measuring Flexing of a Large Spaceborne Structure; Integrated Formation Optical Communication and Estimation System; Making Superconducting Welds between Superconducting Wires; Method for Thermal Spraying of Coatings Using Resonant-Pulsed Combustion; Coating Reduces Ice Adhesion; Hybrid Multifoil Aerogel Thermal Insulation; SHINE Virtual Machine Model for In-flight Updates of Critical Mission Software; Mars Image Collection Mosaic Builder; Providing Internet Access to High-Resolution Mars Images; Providing Internet Access to High-Resolution Lunar Images; Expressions Module for the Satellite Orbit Analysis Program Virtual Satellite; Small-Body Extensions for the Satellite Orbit Analysis Program (SOAP); Scripting Module for the Satellite Orbit Analysis Program (SOAP); XML-Based SHINE Knowledge Base Interchange Language; Core Technical Capability Laboratory Management System; MRO SOW Daily Script; Tool for Inspecting Alignment of Twinaxial Connectors; An ATP System for Deep-Space Optical Communication; Polar Traverse Rover Instrument; Expert System Control of Plant Growth in an Enclosed Space; Detecting Phycocyanin-Pigmented Microbes in Reflected Light; DMAC and NMP as Electrolyte Additives for Li-Ion Cells; Mass Spectrometer Containing Multiple Fixed Collectors; Waveguide Harmonic Generator for the SIM; Whispering Gallery Mode Resonator with Orthogonally Reconfigurable Filter Function; Stable Calibration of Raman Lidar Water-Vapor Measurements; Bimaterial Thermal Compensators for WGM Resonators; Root Source Analysis/ValuStream[Trade Mark] - A Methodology for Identifying and Managing Risks; Ensemble: an Architecture for Mission-Operations Software; Object Recognition Using Feature-and Color-Based Methods; On-Orbit Multi-Field Wavefront Control with a Kalman Filter; and The Interplanetary Overlay Networking Protocol Accelerator.

Source record↗

NASA NTRS1930

The Prevention of the Ice Hazard on Airplanes

A review of various methods to prevent ice formation and adhesion to aircraft surfaces is given. It was concluded that the adhesion of ice to a surface may be reduced somewhat by the application of certain waxes and varnishes. In the experiments described, the varnishes containing calcium stearate and calcium oleate gave the best results. In wind tunnel tests, the adhesion was further reduced by the application of these waxes and varnishes to a thin, heat insulating layer of rubber. The adhesion of ice is greatly reduced when the surface consists of a vehicle which carries an oil in sufficient quantity so that the surface of the vehicle is self lubricating. Ice may be removed from wings, struts, wires and other parts of an airplane during flight by the inflation of properly constructed pneumatic rubber members, providing that these members have been previously treated with a suitable low adhesion oil.

Geer, William C↗

NASA NTRS2018

The Adhesion Strength of Impact Ice Measured Using a Modified Lap Joint Test

Numerous methodologies have been utilized to measure the adhesion strength of impact ice, and the data reported in the literature varies significantly from test to test. In order to initiate an investigation to determine the cause of this disparity, a new test methodology has been developed and utilized in the Icing Research Tunnel at the NASA Glenn Research Center. Data was obtained while varying the temperature, test section velocity, and cloud droplet mean volumetric diameter. The first data set acquired using this new test method is presented. New trends demonstrate the effect of annealing ice samples, with temperature being a key variable. Observations during the test and analysis of the results suggest the presence of large residual stresses in the samples.

Work, Andrew H., Jr.↗

NASA NTRSDate not supplied

Icing Formation Strains on Airfoil Skin

Aircraft icing has long presented a safety hazard to the aerospace industry. One problem inherent to aircraft icing is predicting the adhesive properties of the ice-aircraft interface; values commonly reported span multiple orders of magnitude, making shedding prediction and surface evaluation difficult. An effort has been undertaken at the NASA Glenn Research Center to understand the cause of the scatter in the data. Geometry dependencies, variation in testing procedures, and residual stresses in ice samples have previously been identified as significant contributors to the problem. Residual stresses were singled out for this study, which investigated the strains at the leading edge of a Common Research Model (CRM) wind tunnel model in the NASA Glenn Icing Research Tunnel. Sprays were conducted at a particle size median volumetric diameter (MVD) of 20 µm, with liquid water contents (LWC) spanning from 0.4 to 3.0 g/m3. Total temperatures were varied between 0 and -25 °C, and test section velocity between 51 and 118 m/s. The leading edge was instrumented with custom strain gages, resistance temperature detectors (RTDs), optical fibers, and a pressure mat. Results indicate Δ strains, which were the difference between recorded strains and those predicted from isotropic thermal expansion of aluminum, below -400 µε with consistent patterns of strain across a wide variety of tunnel conditions. Isotropic, linear elastic finite element analysis (FEA) was conducted by varying the temperature of simplified airfoil and ice geometries, producing similar strains to those observed in testing. This allowed induced stresses to be predicted. Predicted stresses were above the expected tensile strength for ice, and suggest a source for previously observed cracking in tunnel ice.

Ice Adhesion↗