Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ideality factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Comparison of CdS and Zn(O,S) Buffer Layers in (Ag,Cu)(In,Ga)Se2 Solar Cells

Cu(In,Ga)Se 2 -based solar cells typically use a C dS buffer layer, even though its relatively low bandgap causes parasitic absorption. While alternatives to CdS have been explored in other studies, limited results have been shown for Ag-alloyed CIGS (ACIGS). In this study, ACIGS solar cells with both CdS and Zn(O,S) buffer layers were fabricated and compared for solar cell performance. The Zn(O,S) buffer slightly improved J sc through reduced absorption, although surface optimization is necessary. The Zn(O,S) ACIGS also had improved FF through reduced series resistance and ideality factor, which could be improved further through optimization. However, the Voc in the Zn(O,S) samples was reduced, likely due to increased bulk and front interface recombination. This study shows the promise of Zn(O,S) as a buffer layer in ACIGS solar cells and suggests pathways for further improvement.

absorption↗
DOE OSTI2023

Ultrawide bandgap vertical β-(Al x Ga1 −x )2O3 Schottky barrier diodes on free-standing β-Ga2O3 substrates

Ultrawide bandgap β-(AlxGa1−x)2O3 vertical Schottky barrier diodes on (010) β-Ga2O3 substrates are demonstrated. The β-(AlxGa1−x)2O3 epilayer has an Al composition of 21% and a nominal Si doping of 2 × 1017 cm−3 grown by molecular beam epitaxy. Pt/Ti/Au has been employed as the top Schottky contact, whereas Ti/Au has been utilized as the bottom Ohmic contact. The fabricated devices show excellent rectification with a high on/off ratio of ∼109, a turn-on voltage of 1.5 V, and an on-resistance of 3.4 mΩ cm2. Temperature-dependent forward current-voltage characteristics show effective Schottky barrier height varied from 0.91 to 1.18 eV while the ideality factor from 1.8 to 1.1 with increasing temperatures, which is ascribed to the inhomogeneity of the metal/semiconductor interface. The Schottky barrier height was considered a Gaussian distribution of potential, where the extracted mean barrier height and a standard deviation at zero bias were 1.81 and 0.18 eV, respectively. A comprehensive analysis of the device leakage was performed to identify possible leakage mechanisms by studying temperature-dependent reverse current-voltage characteristics. At reverse bias, due to the large Schottky barrier height, the contributions from thermionic emission and thermionic field emission are negligible. By fitting reverse leakage currents at different temperatures, it was identified that Poole–Frenkel emission and trap-assisted tunneling are the main leakage mechanisms at high- and low-temperature regimes, respectively. Electrons can tunnel through the Schottky barrier assisted by traps at low temperatures, while they can escape these traps at high temperatures and be transported under high electric fields. This work can serve as an important reference for the future development of ultrawide bandgap β-(AlxGa1−x)2O3 power electronics, RF electronics, and ultraviolet photonics.

Materials Science↗
DOE OSTI2024

Low-temperature electrical properties and barrier inhomogeneities in ITO/β-Ga2O3 Schottky diode

This study reports the electronic properties of the indium tin oxide (ITO)/β-Ga2O3 Schottky diode through the temperature (50–320 K)-dependent current density–voltage, capacitance–voltage, and admittance spectroscopy experiments. The room-temperature turn-on voltage of the ITO/β-Ga2O3 diode was observed to be 0.83 V, and it exhibited a slow increase with decreasing temperature. The ITO/β-Ga2O3 diode's ideality factor (n) varied from 3.92 to 1.05, and the zero-bias Schottky barrier height (φbo) varied from 0.31 to 1.28 eV. The temperature-dependent n and φbo indicate the spatial inhomogeneities of the potential barrier at the Ga2O3-ITO interface. We exploit the Gaussian distribution model to explain the Schottky barrier inhomogeneities, which could be associated with the defects observed by the admittance spectroscopy method.

Engineering↗
DOE OSTI2022

Vertical GaN junction barrier Schottky diodes with near-ideal performance using Mg implantation activated by ultra-high-pressure annealing

Here we report a kV class, low ON-resistance, vertical GaN junction barrier Schottky (JBS) diode with selective-area p-regions formed via Mg implantation followed by high-temperature, ultra-high pressure (UHP) post-implantation activation anneal. The JBS has an ideality factor of 1.03, a turn-on voltage of 0.75 V, and a specific differential ON-resistance of 0.6 mΩ·cm 2 . The breakdown voltage of the JBS diode is 915 V, corresponding to a maximum electric field of 3.3 MV cm –1 . These results underline that high-performance GaN JBS can be realized using Mg implantation and high-temperature UHP post-activation anneal.

42 ENGINEERING↗
DOE OSTI2024

High-voltage AlN Schottky barrier diodes on bulk AlN substrates by MOCVD

Abstract This letter reports the demonstration of Aluminum nitride (AIN) Schottky barrier diodes on bulk AlN substrates by metalorganic chemical vapor phase deposition with breakdown voltages exceeding 3 kV. The devices exhibited good rectifying characteristics with ON/OFF ratios of 10 6 –10 8 and excellent thermal stability from 298 to 623 K. The device Schottky barrier height increased from 0.89 to 1.85 eV, and the ideality factor decreased from 4.29 to 1.95 with increasing temperature, ascribed to the inhomogeneous metal/AlN interface. This work demonstrates the potential of AlN as an ultra-wide bandgap semiconductor for developing multi-kV AlN high-voltage and high-power devices.

Physics↗
DOE OSTI2024

High-current, high-voltage AlN Schottky barrier diodes

AlN Schottky barrier diodes with low ideality factor (<1.2), low differential ON-resistance (<0.6 mΩ cm 2 ), high current density (>5 kA cm −2 ), and high breakdown voltage (680 V) are reported. The device structure consisted of a two-layer, quasi-vertical design with a lightly doped AlN drift layer and a highly doped Al 0.75 Ga 0.25 N ohmic contact layer grown on AlN substrates. A combination of simulation, current–voltage measurements, and impedance spectroscopy analysis revealed that the AlN/AlGaN interface introduces a parasitic electron barrier due to the conduction band offset between the two materials. This barrier was found to limit the forward current in fabricated diodes. Further, we show that introducing a compositionally-graded layer between the AlN and the AlGaN reduces the interfacial barrier and increases the forward current density of fabricated diodes by a factor of 10 4 .

Quiñones, C. E. (ORCID:0000000192703747)↗
DOE OSTI2022

Plant-level performance and degradation of 31 GW DC of utility-scale PV in the United States

In this updated study, which samples 50% more capacity than the original and adds two additional years of operating history, we assess the performance of a fleet of 631 utility-scale PV plants totaling 31.0 GW DC (23.6 GW AC ) of capacity that achieved commercial operations in the United States from 2007-2018 and that have operated for at least two full calendar years. We use detailed information on individual plant characteristics, in conjunction with modeled irradiance data, to model expected or “ideal” capacity factors in each full calendar year of each plant’s operating history. A comparison of ideal versus actual first-year capacity factors finds that this fleet has modestly underperformed initial expectations (as modeled) on average, though perhaps due as much to modeling issues as to actual underperformance. We then analyze fleet-wide performance degradation in subsequent years by employing a “fixed effects” regression model to statistically isolate the impact of age on plant performance. The resulting average fleet-wide degradation rate of -1.2%/year (±0.1%) represents a slight improvement (seemingly driven by the oldest plants in our sample) over the -1.3%/year (±0.2%) found in our original study, yet is still of greater magnitude than is commonly found. We emphasize, however, that these fleet-wide estimates reflect both recoverable and unrecoverable degradation across the entire plant, and so will naturally be of greater magnitude than module- or cell-level studies, and/or studies that focus only on unrecoverable degradation. Moreover, when focusing on a sub-sample of newer and larger plants with higher DC:AC ratios—i.e., plants that more-closely resemble what is being built today—we find a more moderate sample-wide average performance decline of -0.7%/year (±0.4%), which is more in line with other estimates from the recent literature.

14 SOLAR ENERGY↗
DOE OSTI2023

Screen printable copper pastes for silicon solar cells

The current work demonstrates the successful metallization of a PERC silicon solar cell with screen-printable copper (Cu) paste that is sintered at elevated temperature in air atmosphere. The existing state of the art in Silicon (Si) solar cell metallization is silver (Ag) paste; Cu cost is 1/100th the cost of Ag and has a comparable conductivity. However, Cu undergoes rapid oxidation at elevated temperatures and the high diffusion of Cu into Si restricts its usage in the metallization of silicon solar cells. In this paper, a Cu paste containing a proprietary mixture of antioxidant additives and diffusion inhibitors was used to make front gridlines on PERC cells. The Cu-printed cells were fired in an IR belt furnace with a peak temperature of 576°C in air atmosphere. The solar cells discussed here reached an efficiency of 19%, which is 88% of the efficiency measured for a commercial Ag-printed cell. The working devices were further characterized using STEM, EDX, ToF-SIMS and long-term suns-V oc studies demonstrating an absence of Cu diffusion. Furthermore, thermally stressing the Cu-printed solar cells yielded a reduction of less than 1.9% of the initial pseudo fill factor (pFF) after 1000 hours at 200°C. Here, the shunt resistance of cells monitored over 3 years remained within 2.5% of its initial value, which demonstrates the effectiveness of the Cu diffusion barrier.

14 SOLAR ENERGY↗
DOE OSTI2020

Quantifying Losses and Assessing the Photovoltage Limits in Metal–Insulator–Semiconductor Water Splitting Systems

Metal–insulator–semiconductor (MIS) photo-electrocatalysts offer a pathway to stable and efficient solar water splitting. Initially motivated as a strategy to protect the underlying semiconductor photoabsorber from harsh operating conditions, the thickness of the insulator layer in MIS systems has recently been shown to be a critical design parameter which can be tuned to optimize the photovoltage. Here we analyze the underlying mechanism by which the thickness of the insulator layer impacts the performance of MIS photo-electrocatalysts. A concrete example of an Ir/HfO 2 /n-Si MIS system is investigated for the oxygen evolution reaction. The results of combined experiments and modeling suggest that the insulator thickness affects the photovoltage i) favorably by controlling the flux of charge carriers from the semiconductor to the metal electrocatalyst and ii) adversely by introducing nonidealities such as surface defect states which limit the generated photovoltage. It is important to quantify these different mechanisms and suggest avenues for addressing these nonidealities to enable the rational design of MIS systems that can approach the fundamental photovoltage limits. The analysis described in this contribution as well as the strategy toward optimizing the photovoltage are generalizable to other MIS systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Power packet networks for wave energy converter arrays

One of the biggest challenges for all renewable energy sources (RES) is that they are variable power generators which will require reactive power or energy storage systems (ESS) to provide reliable power quality (ideally power factor of one) at the power grid generation side. The present invention is directed to a power packet network (PPN) for integrating wave energy converter (WEC) arrays into microgrids. Specifically, an array of WECs can be physically positioned such that the incoming regular waves will produce an output emulating an N-phase AC system such that the PPN output power is constant. ESS requirements are thereby minimized whilst maintaining grid stability with high power quality. This will enable RES integration onto a future smart grid for large-scale adoption and cost reduction while preserving high efficiency, reliability, and resiliency.

Wilson, David G.↗
DOE OSTI2024

Physical discovery in representation learning via conditioning on prior knowledge

Recent advances in electron, scanning probe, optical, and chemical imaging and spectroscopy yield bespoke data sets containing the information of structure and functionality of complex systems. In many cases, the resulting data sets are underpinned by low-dimensional simple representations encoding the factors of variability within the data. The representation learning methods seek to discover these factors of variability, ideally further connecting them with relevant physical mechanisms. However, generally, the task of identifying the latent variables corresponding to actual physical mechanisms is extremely complex. Here, we present an empirical study of an approach based on conditioning the data on the known (continuous) physical parameters and systematically compare it with the previously introduced approach based on the invariant variational autoencoders. The conditional variational autoencoder (cVAE) approach does not rely on the existence of the invariant transforms and hence allows for much greater flexibility and applicability. Interestingly, cVAE allows for limited extrapolation outside of the original domain of the conditional variable. However, this extrapolation is limited compared to the cases when true physical mechanisms are known, and the physical factor of variability can be disentangled in full. We further show that introducing the known conditioning results in the simplification of the latent distribution if the conditioning vector is correlated with the factor of variability in the data, thus allowing us to separate relevant physical factors. We initially demonstrate this approach using 1D and 2D examples on a synthetic data set and then extend it to the analysis of experimental data on ferroelectric domain dynamics visualized via piezoresponse force microscopy.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Modeling and Market Design Considerations for Conventional and Decarbonized Resources

The following paper reviews various market design issues that will need to be reconsidered due to anticipated changes in the resources that supply energy in wholesale electricity markets. As the energy supply continues towards decarbonization, the change in resource technologies will affect the fundamentals of production scheduling and the policies to address supply variability and uncertainty. We show through simple numerical examples that the existing market design approach based on fuel costs will result in $0/MWh prices with intermittent price spikes during reserve shortages, but that incorporating more granular reserve pricing, energy storage participation, and price-responsive demand participation can restore efficient market clearing with reasonable pricing outcomes. The market design approach fundamentally shifts from fuel based to opportunity cost based. We briefly review alternative market design frameworks that can support this shift, including intraday markets, decentralized markets, flexibility options, and swing contracts. Market designs may also be required to accommodate or support various out-of-market policies and agreements; ideally, these external factors can be integrated into the market design to facilitate efficient exchanges across longer time scales, between other markets, and in support of public policy goals. The paper concludes by discussing how decarbonization trends may affect the design and use of production cost models for short term operations and long term planning studies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Magnetics, Inc. 0077894A7 (Datasheet)

Description of Core Under Test (CUT). Magnetics, Inc. 0077894A7 is a powder core material having low loss and high saturation fields. Known for the marketing name Kool Mu, was transformed by taking the known magnetic material, Sendust, and altered the manufacturing process to lower core losses. Possessing these specific properties makes it ideal for power factor correction circuits as well Pulse and Flyback Transformers. In-Line Noise Filters and Inductors are also common due to the near zero magnetostriction. Exhibits a potential saturation induction of 1 T.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High fidelity simulations of contaminant dispersion in an urban environment with comparison to magnetic resonance imaging measurements

The dispersion of a contaminant in an urban environment has the potential to impact a large population of people. In this work, a complex urban canopy flow based on the Oklahoma City downtown business district circa 2003 is studied using Magnetic Resonance Imaging (MRI) and high-fidelity Large Eddy Simulations (LES). MRI is a novel experimental technique that can provide high-resolution measurements in four dimensions (three spatial and temporal) for lab scale models. The experiments and simulations use the same geometry and boundary conditions providing a one-to-one comparison of the two methods. Results are presented on the time-averaged velocity and concentration fields, the temporal dynamics of the concentration plumes for a transient release, and a novel Cloud Identification Algorithm that can separate plumes produced by periodic contaminant releases used for ensemble averaging over many releases. The MRI and LES datasets both include millions of measurement voxels and the comparisons highlight the complex 3D nature of the flow including strong vertical velocities in spanwise street canyons and flow acceleration in streamwise street canyons. The concentration fields are qualitatively similar albeit the LES shows larger dispersion. A quantitative analysis with performance measures compares the datasets pointwise and demonstrates that the two 3D datasets are similar with respect to many measures including a fractional bias of 0.02 (ideal=0.0), correlation coefficient of 0.87 (ideal = 1.0), and the fraction points within a factor of 2 is 0.98 (ideal = 1.0). Plume analysis compares the arrival and residence time of contaminant and is found to vary significantly with location within the urban environment with arrival times between 0 and 1.25 and differences within the contaminant cloud less than 10% at most locations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Beyond Idealized Models of Nanoscale Metal Hydrides for Hydrogen Storage

Metal hydrides are attractive for compact, low-pressure hydrogen storage, yet a foundational understanding of factors governing their thermodynamics and kinetics is still lacking. Predictive modeling from the atomic to the microstructural scale plays a critical role in addressing these gaps, particularly for nanoscale materials, which promise improved performance but are difficult to probe. In this paper, we summarize strategies being developed within the Hydrogen Materials—Advanced Research Consortium (HyMARC) for going beyond conventional models to incorporate more complex physics, more realistic structures, and better approximation of operation conditions in simulations of nanoscale metal hydrides. We highlight four beyond-ideal factors that influence predicted performance: (1) surface anharmonic dynamics, (2) interface and surface energy penalties, (3) mechanical stress under confinement, and (4) the presence of native surface oxide. Approaches for addressing these factors are demonstrated on model materials representative of high-capacity hydrogen storage systems, and implications for understanding performance under operating conditions are discussed.

08 HYDROGEN↗
DOE OSTI2024

KCl-UCl 3 molten salts investigated by Ab Initio Molecular Dynamics (AIMD) simulations

Ab Initio Molecular Dynamics (AIMD) simulations are performed on molten KCl-UCl3 salt mixtures to determine energies, heat capacities, and densities. The density-dependent energy correction (DFT-dDsC), Grimme et al.'s DFT-D3, and Langreth & Lundqvist (vdW-cx) models are used for dispersion forces and combined with the Perdew-Burke-Ernzerhof (PBE) exchange-correlation potential with a Hubbard U parameter for the 5f electrons of uranium. After validating predictions for the end-member systems to literature data, KCl-UCl 3 mixtures are studied at select temperatures. Densities and energies both deviate from ideal solution behavior, with the maximum deviation occurring around 36% UCl 3 for mixing energies and slightly lower (29% UCl3) for densities. Compared to the NaCl-UCl 3 system, which was previously investigated using the same simulation methodologies, the KCl-UCl 3 density and mixing energy deviations from ideal solution behavior are larger by almost a factor of two. No deviation from ideal solution behavior for heat capacity was observed. The AIMD predictions for mixing energies and densities agree qualitatively with experimental data, though the spread in data obtained from the various dispersion force models utilized, measurements, and empirical estimates makes strong conclusions difficult. The dependence of thermodynamic and thermophysical properties on composition is correlated with the local chemistry of the solution phase, in particular, the tendency of UCl 3 to form network structures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

KCl-UCl 3 molten salts investigated by Ab Initio Molecular Dynamics (AIMD) simulations: A comparative study with three dispersion models

Ab Initio Molecular Dynamics (AIMD) simulations are performed on molten KCl-UCl 3 salt mixtures to determine energies, heat capacities, and densities. The density-dependent energy correction (DFT-dDsC), Grimme et al.’s DFT-D3, and Langreth & Lundqvist (vdW-cx) models are used for dispersion forces and combined with the Perdew-Burke-Ernzerhof (PBE) exchange-correlation potential with a Hubbard U param eter for the 5$f$ electrons of uranium. After validating predictions for the end-member systems to literature data, KCl-UCl 3 mixtures are studied at select temperatures. Densities and energies both deviate from ideal solution behavior, with the maximum deviation occurring around 36% UCl 3 for mixing energies and slightly lower (29% UCl 3 ) for densities. Compared to the NaCl-UCl 3 system, which was previously investigated using the same simulation methodologies, the KCl-UCl 3 density and mixing energy deviations from ideal solution behavior are larger by almost a factor of two. No deviation from ideal solution behavior for heat capacity was observed. The AIMD predictions for mixing energies and densities agree qualitatively with experimental data, though the spread in data obtained from the various dispersion force models utilized, measurements, and empirical estimates makes strong conclusions difficult. The dependence of thermodynamic and thermophysical properties on composition is correlated with the local chemistry of the solution phase, in particular, the tendency of UCl 3 to form network structures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Microphysics of liquid water in sub-10 nm ultrafine aerosol particles

Abstract. Ultrafine aerosol particles with sizes smaller than 50 nm have been shown in recent studies to serve as a large source of cloud condensation nuclei that can promote additional cloud droplet formation under supersaturation conditions. Knowledge of the microphysics of liquid water in these droplets remains limited, particularly in the sub-10 nm particle size range, due to experimental and theoretical challenges associated with the complexity of aerosol components and the small length scales of interest (e.g., difficulty of precisely sampling the liquid–air interface, questionable validity of mean-field theoretical representations). Here, we carried out molecular dynamics (MD) simulations of aerosol particles with diameters between 1 and 10 nm and characterized atomistic-level structure and water dynamics in well-mixed and phase-separated systems with different particle sizes, NaCl salinities, and pimelic acid (PML) organic surface loadings as a function of distance from the time-averaged Gibbs dividing interface or instantaneous water–air interface. We define a sphericity factor (ϕ) that can shed light on the phase-mixing state of nanodroplets, and we reveal an unexpected dependence of mixing state on droplet size. Our results also evidence an ion concentration enhancement in ultrafine aerosols, which should modulate salt nucleation kinetics in sub-10 nm droplets, and provide detailed characterization of the influence of droplet size on surface tension and on water self-diffusivity near the interface. Analysis of water evaporation free energy and water activity demonstrates the validity of the Kelvin equation and Köhler theory at droplet sizes larger than 4 nm under moderate salinities and organic loadings and the need for further extension to account for ion concentration enhancement in sub-10 nm aerosols, droplet-size-dependent phase separation effects, and a sharp decrease in the cohesiveness of liquid water in sub-4 nm droplets. Finally, we show that an idealized fractional surface coating factor (fs) can be used to categorize and reconcile water accommodation coefficients (α*) observed in MD simulations and experimental results in the presence of organic coatings, and we resolve the droplet size dependence of α*.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗