SEARCH · Search NASA

Results for “Inappropriate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2005

Intelligent Engine Systems Work Element 1.2: Malfunction and Operator Error Reduction

Jet engines, although highly reliable and safe, do experience malfunctions that cause flight delays, passenger stress, and in some cases, in conjunction with inappropriate crew response, contribute to airplane accidents. On rare occasions, the anomalous engine behavior is not recognized until it is too late for the pilots to do anything to prevent or mitigate the resulting engine malfunction causing in-flight shutdowns (IFSDs), aborted takeoffs (ATOs), or loss of thrust control (LOTC). In some cases, the crew response to a myriad of external stimuli and existing training procedures is the source of the problem mentioned above. The problem is the reduction of jet engine malfunctions (IFSDs, ATOs, and LOTC) and inappropriate crew response (PSM+ICR) through the use of evolving and advanced technologies. The solution is to develop the overall system health maintenance architecture, detection and accommodation technologies, processes, and enhanced crew interfaces that would enable a significant reduction in IFSDs, ATOs, and LOTC. This program defines requirements and proposes a preliminary design concept of an architecture that enables the realization of the solution.

Wiseman, Matthew↗

NASA NTRS2007

Did Vertigo Kill America's Forgotten Astronaut?

On November 15, 1967, U.S. Air Force test pilot Major Michael J. Adams was killed while flying the X-15 rocket-propelled research vehicle in a parabolic spaceflight profile. This flight was part of a joint effort with NASA. An electrical short in one of the experiments aboard the vehicle caused electrical transients, resulting in excessive workload by the pilot. At altitude Major Adams inappropriately initiated a flat spin that led to a series of unusual aircraft attitudes upon atmospheric re-entry, ultimately causing structural failure of the airframe. Major Adams was known to experience vertigo (i.e. spatial disorientation) while flying the X-15, but all X-15 pilots most likely experienced vertigo (i.e. somatogravic, or "Pitch-Up", illusion) as a normal physiologic response to the accelerative forces involved. Major Adams probably experienced vertigo to a greater degree than did others, since prior aeromedical testing for astronaut selection at Brooks AFB revealed that he had an unusually high degree of labyrinthine sensitivity. Subsequent analysis reveals that after engine burnout, and through the zenith of the flight profile, he likely experienced the oculoagravic ("Elevator") illusion. Nonetheless, painstaking investigation after the mishap revealed that spatial disorientation (Type II, Recognized) was NOT the cause, but rather, a contributing factor. The cause was in fact the misinterpretation of a dual-use flight instrument (i.e. Loss of Mode Awareness), resulting in confusion between yaw and roll indications, with subsequent flight control input that was inappropriate. Because of the altitude achieved on this flight, Major Adams was awarded Astronaut wings posthumously. Understanding the potential for spatial disorientation, particularly the oculoagravic illusion, associated with parabolic spaceflight profiles, and understanding the importance of maintaining mode awareness in the context of automated cockpit design, are two lessons that have direct application to the commercial space industry today.

Bendrick, Gregg A.↗

NASA NTRS2020

Names Don't Fly: Smart Filters for Profanity Detection and Classification in User-Generated Content

Generally, names associate with a person’s identity. But what if in the pretext of a legitimate name and given the opportunity, users of software provide names to online web forms that carry along offensive language, slurs, and other profanity that is then sent to Mars ? The answer is simple: they don’t fly. In this paper,we perform model explorations to detect and classify inappropriate content in the names submitted from people across the world to ‘Send Your Names to MARS’ public engagement campaign.We propose a novel pipeline approach, that can effectively overcome the issues of lack of negative samples, noisy labels by gathering expert knowledge over time with human(s) in the loop and data augmentation, and achieve high accuracy in classifying inappropriate names with very little or no context. We describe cloud-based infrastructure to deploy our application and run predictions on large-scale data through our pipeline and achieve significant speedup over offline processes, with enhanced reliability and security.

Soderstrom, Tomas↗

NASA NTRSDate not supplied

Novel Approach to Simulating Diagnostic Capabilities in Medical Resource Risk Assessment

Diagnostics represent a key subset of medical resources considered for helping mitigate and control spaceflight medical risk. Historically, when modeling the medical risk domain for spaceflight, diagnostic resources have been handled like any other medical resource used for treatment. That is to say, the resource being unavailable will result in the related condition having suboptimal treatment outcomes. However in the real world, should a diagnostic resource be unavailable, a more analogous effect would be that the condition might be misdiagnosed, and thus inappropriate treatment applied. This talk presents an alternative means of representing diagnostic resources within the Medical Extensible Dynamic Probabilistic Risk Assessment Tool (MEDPRAT) that can simulate the effect both in risk, resource consumption, and competition for resources of a missing or depleted diagnostic. The scenario where a differential diagnosis may not be possible for abdominal conditions that use an ultrasound machine as a diagnostic tool is considered. Two approaches for modeling the effect of not having a diagnostic capability on the medical system are demonstrated. In the “simple” approach, it is assumed that any abdominal condition requiring the ultrasound machine for diagnosis is mis-diagnosed and treated as an appendicitis. This is represented by replacing the treatment for the affected conditions with the treatment for appendicitis, thereby changing the optimized medical set available for treatment for the remainder of the mission. In the “complex” approach, MEDPRAT treatment clusters are utilized to capture and represent overlapping treatment between the misdiagnosed condition and appendicitis. This elicits both the effect that inappropriate treatment is applied, resulting in wasted resource consumption, and that treatment which was truly needed for the misdiagnosed condition was not applied, which reduces the treatment effectiveness. In this talk, results comparing the simple and complex diagnostic capability approach to a baseline where the diagnostic is treated as a traditional resource is presented. Either approach provides an option for a more analogous representation of diagnostic resources and provides insight into how the modeled spaceflight medical resources and outcomes change when that diagnostic is unavailable.

C. M. Gasiewski↗

DOE OSTI2024

Revealing the Nature of Binary-Phase on Structural Stability of Sodium Layered Oxide Cathodes

The emergence of layered sodium transition metal oxides featuring a multiphase structure presents a promising approach for cathode materials in sodium-ion batteries, showcasing notably improved energy storage capacity. However, the advancement of cathodes with multiphase structures faces obstacles due to the limited understanding of the integrated structural effects. Herein, the integrated structural effects by an in-depth structure-chemistry analysis in the developed layered cathode system Na x Cu 0.1 Co 0.1 Ni 0.25 Mn 0.4 Ti 0.15 O 2 with purposely designed P2/O3 phase integration, are comprehended. The results affirm that integrated phase ratio plays a pivotal role in electrochemical/structural stability, particularly at high voltage and with the incorporation of anionic redox. In contrast to previous reports advocating solely for the enhanced electrochemical performance in biphasic structures, it is demonstrated that an inappropriate composite structure is more destructive than a single-phase design. The in situ X-ray diffraction results, coupled with density functional theory computations further confirm that the biphasic structure with P2:O3 = 4:6 shows suppressed irreversible phase transition at high desodiated states and thus exhibits optimized electrochemical performance. Finally, these fundamental discoveries provide clues to the design of high-performance layered oxide cathodes for next-generation SIBs.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Comprehensive Performance Calibration Guidance for Perovskites and Other Emerging Solar Cells

Emerging photovoltaic (PV) technologies (e.g., organic, perovskite, and solution processed quantum dot) have attracted remarkable attention with the rapid growth of their efficiencies, and their transition toward commercialization. Accurate and reliable efficiency measurements of these PV technologies are crucial, yet much more complicated than for conventional PV technologies due to the former's pronounced dynamic responses to changes in measurement conditions (e.g., current–voltage (I–V) scan rate and preconditioning) and their susceptibility to degradation. Adjustments to the measurement procedures are therefore necessary so that a reproducible “steady state” is reached during measurement. Furthermore, given the small size of many emerging cells, inappropriate device area definition and solar simulator setup can lead to measurement errors. Here, comprehensive efficiency calibration guidance is offered for emerging solar cells, including area measurement; spectral irradiance translation to standard test conditions; and steady-state electrical performance. The necessity of reporting steady-state efficiency is justified with a statistical performance comparison between conventional and steady-state I–V scans over hundreds of cells the group has received globally for efficiency certifications. The procedures described here do not require specialized measurement instrumentation; what matters most are changes to the measurement protocols. These described changes aim to enable better comparisons between reported efficiencies.

14 SOLAR ENERGY↗

DOE OSTI2021

Instruction Roofline: An insightful visual performance model for GPUs

The Roofline performance model provides an intuitive approach to identify performance bottlenecks and guide performance optimization. However, the classic FLOP-centric approach is inappropriate for the emerging applications that perform more integer operations than floating point operations. In this article, we reintroduce our Instruction Roofline Model on NVIDIA GPUs and expand our evaluation of it. The Instruction Roofline incorporates instructions and memory transactions across all memory hierarchies together, and provides more performance insights than the FLOP-oriented Roofline Model, that is, instruction throughput, stride memory access patterns, bank conflicts, and thread predication. We use our Instruction Roofline methodology to analyze eight proxy applications: HPGMG from AMReX, Matrix Transpose benchmarks, ADEPT from MetaHipMer's sequence alignment phase, EXTENSION from MetaHipMer's local assembly phase, CUSP, cuSPARSE, cudaTensorCoreGemm, and cuBLAS. We demonstrate the ability of our methodology to understand various aspects of performance and performance bottlenecks on NVIDIA GPUs and motivate code optimizations.

Ding, N↗

DOE OSTI2020

Instability and treatments of the coupled discrete element and lattice Boltzmann method by the immersed moving boundary scheme

The immersed moving boundary (IMB) scheme has been extensively used to couple the discrete element method (DEM) with the lattice Boltzmann method (LBM). In the literature, only the formulation of IMB for lattice nodal cells covered by a single-solid particle was given. The treatment of situations where a nodal cell is covered by two or more solid particles is seldom discussed. It is found that some numerical instability can occur for such situations due to an inappropriate computation of the weighting function in the IMB formulation. This work presents an enhanced treatment that can resolve the issue and validates it using some benchmark tests. Furthermore, to avoid the extra costs associated with the treatment and simplify the complicated procedure introduced, a simplified IMB scheme is proposed. The accuracy of both enhanced and simplified IMB schemes are validated by test cases including single-particle sedimentation, two-particle drafting-kissing-tumbling phenomenon, and multiple-particle sedimentation. Then, the robustness of both schemes is examined and discussed using a specially designed flow past cylinders test. Overall, the simplified IMB scheme is proved to be robust and sufficiently accurate and simpler and more effective than the enhanced scheme.

42 ENGINEERING↗

DOE OSTI2021

Long-term single-column model intercomparison of diurnal cycle of precipitation over midlatitude and tropical land

General Circulation Models (GCMs) have for decades exhibited difficulties in modelling the diurnal cycle of precipitation (DCP). This issue can be related to inappropriate representation of the processes controlling sub-diurnal phenomena like convection. In this study, 11 single-column versions of GCMs are used to investigate the interactions between convection and environmental conditions, processes that control nocturnal convections, and the transition from shallow to deep convection on a diurnal time-scale. Long-term simulations are performed over two continental land sites: the Southern Great Plains (SGP) in the USA for 12 summer months from 2004 to 2015 and the Manacapuru site at the central Amazon (MAO) in Brazil for two full years from 2014 to 2015. The analysis is done on two regimes: afternoon convective regime and nocturnal precipitation regime. Most models produce afternoon precipitation too early, likely due to the missing transition of shallow-to-deep convection in these models. At SGP, the unified convection schemes better simulate the onset time of precipitation. At MAO, models produce the heating peak in a much lower level compared with observation, indicating too shallow convection in the models. For nocturnal precipitation, models that produce most of nocturnal precipitation all allow convection to be triggered above the boundary layer. This indicates the importance of model capability to detect elevated convection for simulating nocturnal precipitation. Sensitivity studies indicate that (a) nudging environmental variables towards observations has a minor impact on DCP, (b) unified treatment of shallow and deep convection and the capability to capture mid-level convection can help models better capture DCP, and (c) the interactions of the atmosphere with other components in the climate system (e.g. land) are also important for DCP simulations in coupled models. Finally, these results provide long-term statistical insights on which physical processes are essential in climate models to simulate DCP.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Nondestructive neutron imaging diagnosis of acidic gas reduction catalyst after 400-Hour operation in natural gas furnace

Residential natural gas furnaces are the primary space-heating devices in US homes, leading to substantial environmental impact caused by the acidic components in the furnace combustion gases. Here, to experimentally demonstrate acidic gas reduction in a furnace, a monolithic catalyst was fabricated and was called the AGR. A commercially-available condensing furnace was retrofitted with the AGR, and a 400-hour reliability and durability test was conducted. The results showed that the AGR significantly reduced acidic gases in the flue gas and produced condensate with neutral pH. Challenges were also revealed: inappropriate condensate drainage caused incomplete combustion and amorphous carbon deposits. To nondestructively survey the internal state of the AGR, neutron computed tomography (NCT) was employed to produce spatially resolved 2D and 3D representations of the 2-L, aged AGR component. The NCT results confirm the integrity of the AGR component, which consists of two blocks, without deformation or damage to AGR channels. The distribution of the particle accumulation in the middle of the top block was visibly heavier than the entrance and exit of the top block. The representative cross-section views revealed significant aggregation in the central region but not at the rim. The spatially resolved details provide in-depth diagnosis, evaluation, and understanding of the AGR. The insights can enable new AGR designs that realize a uniform and self-cleaning flow pattern, alleviate significant particle aggregation, and thus enhance AGR-enabled furnace performance. The neutron imaging method demonstrates the good potential that can diagnose faults and improve the design, optimization, and production processes of novel catalysts and other components or systems with heavy metal shell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Empirical evidence that mean soil contaminant concentration is not a conservative indicator of external exposure to wildlife

Adequate information on external exposure is often a limiting factor in ecological risk assessments because of a lack of exposure data for free-ranging animals as they interact with a heterogeneous distribution of contaminants. Instead, most wildlife exposure data are estimated from model simulations. However, empirical exposure data are rarely available to verify model results, or to test fundamental assumptions inherent in exposure assessments. We used novel, GPS-coupled radiation dosimeters on reindeer (Rangifer tarandus) to quantify their external exposure for five months in a Chernobyl fallout affected mountainous area of Norway. The exposure data were then used to test a fundamental assumption in screening-level risk assessments: Mean soil contaminant concentrations can be used to conservatively estimate chronic external exposures to representative animals. External exposure and GPS coordinates were obtained hourly and compared to model simulations of exposure based on airborne surveys of 137 Cs soil contamination. Our objectives were to determine 1) if modelled dose estimates based on mean 137 Cs soil concentrations were conservative, and 2) if modelled dose estimates could be improved by adjusting for spatial–temporal heterogeneity of contaminants using 137 Cs concentrations within reindeers’ GPS-defined home ranges and core areas. We found that external exposure modelled from mean soil contaminant concentrations underestimated exposure by 70% compared to empirical measurements from GPS-dosimeter collars worn on individual animals. Using area-weighted mean contaminant levels within the animals’ home range improved the model estimates, but still underestimated the field dosimeter data by 53%. The best estimate of external exposure was obtained when high-use areas within their home range, along with spatial heterogeneity of the contaminant, was accounted for by using area-weighted mean soil contaminant levels within GPS-derived core areas. Accounting for temporal use of core areas within animals’ home range provided a 24% improvement. Here, a comparison of our analyses to similar work performed on Chernobyl wolves found the two studies concur that risk assessors should be cautious in relying on the paradigm of using averaged soil contaminant levels to provide conservative estimates of external exposure to representative individuals. Results of modelled external exposure based on mean soil contaminant concentrations could misguide assessors and cause inappropriate management decisions.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗

DOE OSTI2020

Landslide monitoring using seismic refraction tomography – The importance of incorporating topographic variations

Seismic refraction tomography provides images of the elastic properties of subsurface materials in landslide settings. Seismic velocities are sensitive to changes in moisture content, which is a triggering factor in the initiation of many landslides. However, the application of the method to long-term monitoring of landslides is rarely used, given the challenges in undertaking repeat surveys and in handling and minimizing the errors arising from processing time-lapse surveys. This work presents a simple method and workflow for producing a reliable time-series of inverted seismic velocity models. This method is tested using data acquired during a recent, novel, long-term seismic refraction monitoring campaign at an active landslide in the UK. Potential sources of error include those arising from inaccurate and inconsistent determination of first-arrival times, inaccurate receiver positioning, and selection of inappropriate inversion starting models. At our site, a comparative analysis of variations in seismic velocity to real-world variations in topography over time shows that topographic error alone can account for changes in seismic velocity of greater than ±10% in a significant proportion (23%) of the data acquired. The seismic velocity variations arising from real material property changes at the near-surface of the landslide, linked to other sources of environmental data, are demonstrated to be of a similar magnitude. Over the monitoring period we observe subtle variations in the bulk seismic velocity of the sliding layer that are demonstrably related to variations in moisture content. This highlights the need to incorporate accurate topographic information for each time-step in the monitoring time-series. The goal of the proposed workflow is to minimize the sources of potential errors, and to preserve the changes observed by real variations in the subsurface. Following the workflow produces spatially comparable, time-lapse velocity cross-sections formulated from disparate, discretely-acquired datasets. These practical steps aim to aid the use of the seismic refraction tomography method for the long-term monitoring of landslides prone to hydrological destabilization.

Whiteley, J. S.↗

DOE OSTI2024

The role of annealing and grain boundary controls on the mechanical properties of limestones and marbles

Chemical and mechanical processes are coupled in many geological and geochemical environments. Reactive processes anneal defects and restructure grain boundaries, modifying their elastic properties, levels of internal friction, wave propagation rates and fracture behaviors. The nature of these changes is, however, contingent on the initial state of the rock. Here, in this study, impulse excitation was used to measure changes in mechanical properties as a function of dry and steam heating time at 300 °C for three carbonate rocks: Carrara marble, Carthage marble (Burlington Limestone), and Texas Cream limestone (Edwards limestone), with initial porosities of about 1 %, 3 %, and 27 %, respectively. Frequency-dependent phenomena along with mineral recrystallization were observed. This was coupled with small-angle X-ray and neutron scattering analysis to determine the relationship between changes in bulk mechanical and microstructural properties. An observed decrease in both the Young's and shear moduli in the experimental limestones as a function of heating time reflects and quantifies a reduction in the stiffness of the rock due to annealing. The internal friction of the samples first increases then decreases with reaction time, reflecting defect annealing, but this was balanced against grain boundary dissolution apparently driven by condensation of steam in the confined grain-boundary environment. This suggests an increase in the boiling point under confinement leading to dissolution, increased porosity and widening of the grain boundaries. In addition, comparison of small-angle X-ray and neutron scattering results suggests that it is inappropriate to assume that pores are empty for quantitative analysis of typical small-angle scattering samples.

58 GEOSCIENCES↗

DOE OSTI2021

Trends in Financial Relationships Between Industry and Radiation Oncologists Versus Other Physicians in the United States from 2014 to 2018

The Open Payments transparency program publishes data on industry-physician payments, in part to discourage relationships considered inappropriate including gifts, meals, and speaker’s bureau fees. We evaluated trends in physician-level payments to test whether implementation of Open Payments resulted in fewer industry–radiation oncologist (RO) interactions or shifted interactions toward those considered more appropriate compared with medical oncologists (MOs) and other hospital-based physicians (HBPs).

62 RADIOLOGY AND NUCLEAR MEDICINE↗

DOE OSTI2021

Catalytic site ensembles: A context to reexamine the Langmuir-Hinshelwood kinetic description

The Langmuir-Hinshelwood formalism describes catalytic reactions of Langmuirian surface species under the assumption that all adsorbates are randomly-distributed – enabling adjacency of surface-bound intermediates to be determined solely by coverages of single-site occupants. We demonstrate herein that this approximation is inappropriate even for simple catalytic reactions (e.g. A + A → A 2 ) and manifestly neglects islanding of slowly-consumed species and partitioning of highly-reactive species inherently engendered by ≥ two-site elementary steps (e.g. A*–A* → A 2(g) + *–*). Rigorous description of kinetically-consequential islanding/partitioning phenomena requires explicit description of the coverage and chemical dynamics of all multi-site ensembles. Higher-order, ensemble-specific rate terms identify the particular microscopic events relevant to each ensemble, and, in doing so, reveal that each elementary step (e.g. A (g) adsorption) describes not one event (e.g. A (g) + * → A*) , but a sum over all ensemble-specific paths (e.g. A (g) + *–* → A*–* and A (g) + A*–* → A*–A*). De-convoluting each elementary step into its constituent multi-site paths proffers kinetic detail otherwise inaccessible – enabling (i) identification of rate- and selectivity-determining site ensembles, (ii) calculation of rates and degrees of rate control of ensemble-specific elementary steps, (iii) incorporation of adsorbate surface diffusion, (iv) incorporation of lateral adsorbate interactions, and (v) quantitative description of catalysis of multi-site-occupying intermediates (e.g. *C n H m * species in hydrocarbon (de-)hydrogenation and C-C bond coupling/cleavage reactions) which we demonstrate here is inaccessible to the Langmuir-Hinshelwood formalism even if adsorbate surface diffusion is infinitely-fast.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Numerical evaluation of photosensitive tracers as a strategy for separating surface and subsurface transient storage in streams

For this work, we numerically evaluated photosensitive tracers as a potential strategy for separating the effects of surface and hyporheic storage zones (SSZs and HSZs, respectively) on stream corridor transport. Correctly separating HSZ and SSZ effects is critical to estimating the hydro-biogeochemical function of a stream because HSZs and SSZs expose solutes to significantly different biogeochemical conditions, like sunlight exposure, microbial processes, and oxygen availability. Our numerical experiments used a multiscale river-corridor transport model implemented in the ATS code, which accommodates multiple storage zones with distinct travel time distributions and biogeochemical reactions. For parameter inferences, we used Bayesian inverse modeling. We found that breakthrough curves for photo-decaying tracers from day and night injection can delineate surface and hyporheic transient storage contributions, but only when interpreted jointly through a two-storage zone model. Numerical experiments that used only daytime injection or interpreted breakthrough curves with a single storage zone model yielded good fit to breakthrough curves, but parameter estimates were biased and controlling processes misattributed, examples of good model fits for the wrong reasons. Using those biased parameter estimates in reactive transport simulations resulted in significantly different projections of denitrification, which underscores the potential for stream function to be mischaracterized if tracer tests are interpreted through an inappropriately simplified model for transient storage. More generally, this study highlights the role of modeling in evaluating the experimental design and identifying the potential of system mischaracterization and its implications.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Surface oxygen exchange kinetics of mixed conducting oxides: Dilatometric vs electrical conductivity relaxation study

The surface oxygen exchange kinetics of mixed ionic-electronic conducting (MIEC) oxides play a crucial role in a variety of applications, including solid oxide fuel/electrolysis cells (SOFCs/SOECs), permeation membranes and sensors. To date, a variety of methods, including isotope exchange, electrical conductivity, optical absorptivity and thermogravimetry relaxation, and impedance spectroscopy have been used to measure the oxygen exchange coefficient of MIEC oxides. Each of these methods have their advantages and limitations, depending on the physical and chemical properties of the investigated materials and their sample dimensions and densities. Here, we demonstrate the ability to precisely measure the surface oxygen exchange coefficient (k chem ) of MIEC model material Pr 0.1 Ce 0.9 O 2-δ (PCO) by use of dilatometric relaxation measurements, particularly of interest for materials that exhibit larger chemical expansion coefficients. This is achieved by use of porous bulk specimens to ensure that the contribution of oxygen exchange to the overall kinetics is dominant. We demonstrate that k chem values extracted from chemical expansion relaxation measurements on PCO are nearly identical to those derived from electrical conductivity relaxation measurements. As a result, this provides the opportunity to precisely investigate the oxygen exchange and chemical expansion kinetics of a wide range of materials used in high-temperature applications, particularly where more conventional methods are difficult or inappropriate to apply.

(Pr,Ce)O2-x↗

DOE OSTI2026

Response to the comments on creep-induced elemental redistribution at grain boundaries of 304L stainless steel – An experimental evidence for diffusional creep mechanisms

Sandström and He reanalyzed our 304L creep data (Acta Materialia 121137, 2025) at 10 MPa/750 °C and proposed that: (i) primary dislocation creep dominates based on the ϕ -model; (ii) measured creep rates deviate from published 304H data and Coble creep predictions using literature grain boundary (GB) diffusivity; and (iii) creep-induced elemental redistribution (CIER) could be explained by dislocation emission/absorption (DEAA) and GB creep (GBC), as opposed to diffusional creep. Here, in this response, we propose that: (i) the creep behavior at 15 MPa/750 °C—for which we demonstrated CIER—is only partially captured by the ϕ -model; (ii) direct comparison between 304L and 304H creep data is inappropriate due to carbides in 304H, and Coble creep predictions estimated from CALPHAD-based bulk diffusivity span experimental rates; and (iii) CIER exhibits distinct fingerprint for diffusional creep characterized by anisotropy and stress orientation dependence whereas neither DEAA nor GBC have been mechanistically substantiated.

36 - MATERIALS SCIENCE↗