Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOAD DISTRIBUTION - WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Composite Structure with Load Distribution Devices, and Method for Making Same

An improved composite structure and method for making same has been provided. The provided improved composite structure has locally strengthened areas within a reinforcement region. The locally strengthened areas within the reinforcement region have load distribution devices to redistribute load in order to (i) locally strengthen an area around damage induced by an initial momentary and direct transmitted load, and (ii) limit growth and propagation of damage induced by an initial momentary and direct transmitted load during a subsequent unbalance load. The improved composite structure reduces the impact of the fan blade out phenomenon in a weight efficient manner.

Watson, Bill Russell↗

Resume of Present Data on Load Distribution on Slots and Flaps, Special Report

This report covers a study of the generally available data on load distribution on slots and flaps. The study was made by the National Advisory Committee for Aeronautics at the request of the Material Division, Army Air Corps to furnish information applicable to design criteria for slots and flaps of various types. The data are presented in three main sections: slots (Handley page type), auxiliary airfoils (fixed), and flaps.

Wenzinger, Carl J.↗

Flight Investigation on a Fighter-type Airplane of Factors which Affect the Loads and Load Distributions on the Vertical Tail Surfaces During Rudder Kicks and Fishtails

Results are presented of a flight investigation conducted on a fighter-type airplane to determine the factors which affect the loads and load distributions on the vertical tail surfaces in maneuvers. An analysis is made of the data obtained in steady flight, rudder kicks, and fishtail maneuvers. For the rudder kicks, the significant loads were the "deflection load" resulting from an abrupt control deflection and the "dynamic load" consisting of a load corresponding to the new static equilibrium condition for the rudder deflected plus a load due to a transient overshoot. The minimum time to reach the maximum control deflection attainable by the pilot in any flight condition was found to be a constant. In the fishtail maneuvers, it was found that the pilot tends to deflect the rudder in phase with the natural frequency of the airplane. The maximum loads measured in fishtails were of the same order of magnitude as those from a rudder kick in which the rudder is returned to zero at the time of maximum sideslip.

Boshar, John↗

On-Orbit Evaluation of a New Treadmill Harness for Improved Crewmember Comfort and Load Distribution

The current design of the International Space Station (ISS) Treadmill Harness has been reported to cause pain and discomfort to crewmembers during exercise. The Harness Station Development Test Objective (SDTO) provided participating crewmembers (n = 6) with a new harness design, the "Glenn Harness," to evaluate for comfort and loading as compared to the current Treadmill Harness. A novel suite of load-sensing instrumentation was developed to noninvasively measure load distribution and provided a first-ever quantification of actual dynamic loads during treadmill exercise. In addition, crew debriefs provided feedback on harness preference and overall impressions. Conclusions: Post-flight analysis in returned Glenn Harnesses (n = 3) showed minimal wear and tear. Four of the six subjects found the Glenn Harness to be more comfortable in this on-orbit, side-by-side comparison as measured by the crew comfort questionnaire and crew debriefs. Specific areas for improvement have been identified, and forward recommendations will be provided to the Human Research Program. The protocol developed for the SDTO provided valuable insight into crew comfort issues, design improvements, and loading preferences for exercise harnessing, which lays the groundwork for better harnessing systems and training protocols.

Perusek, G. P.↗

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Paul W Giel↗

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Turbine↗

Space shuttle: An investigation of the load distribution over the SRB and external tank of a 0.004 scale model of the 049 space shuttle launch configuration

A study was conducted in a trisonic wind tunnel to determine the load distribution over the external tank and solid rocket boosters of the space shuttle launch configuration. The external tank was sting-supported and the solid rocket boosters and orbiter were mounted directly on the external tank. The external tank was, instrumented with 152 pressure orifices and the solid rocket boosters contained 78 orifices. The pressure data were obtained for various combinations of the three geometric components as the gap size between the external tank and the solid rocket boosters, angle of attack, and angle of sideslip were varied. Mach numbers ranged from 0.8 to 1.96.

Lott, R. A.↗

Explicit modeling and computational load distribution for concurrent processing simulation of the space station

Two important aspects of concurrent processing under development at TRW are discussed. These are: (1) the derivation of explicit mathematical models of multibody dynamic systems, and (2) a balanced computational load distribution (BCLD) among loosely coupled computational units (processors) of a concurrent processing system. The developed methodologies are demonstrated by way of an application to the Phase 1 of the Space Station - a task being performed by TRW under NASA/JSC contract NAS9-17778. The mathematical model of the Space Station consists of three interconnected flexible bodies capable of undergoing large, rigid-body motion with respect to each other. Body 1 is the main central body and contains the pressurized modules inboard of the two Alpha gimbals. Bodies 2 and 3 are the starboard and port bodies connected to Body 1 at the Alpha gimbals and include all components on the transverse booms outboard of the Alpha gimbals (including the solar arrays). The control systems in the model maintain Body 1 in a prescribed 3-axis attitude control mode, while producing large-angle rotations of the flexible solar arrays to position them normal to the sun-line.

Gluck, R.↗

Comparison of Water-Load Distributions Obtained during Seaplane Landings with Bureau of Aeronautics Specifications. TED No. NACA 2413

Bureau of Aeronautics Design Specifications SS-IC-2 for water loads in sheltered water are compared with experimental water loads obtained during a full--scale landing investigation. This investigation was conducted with a JRS-1 flying boat which has a 20 degrees dead-rise V-bottom with a partial chine flare. The range of landing conditions included airspeeds between 88 and 126 feet per second, sinking speeds between 1.6 and 9.1 feet per second, flight angles less than 6 degrees, and trims between 2 degrees and 12 degrees. Landings were moderate and were made in calm water. Measurements were obtained of maximum over-all loads, maximum pitching moments, and pressure distributions. Maximum experimental loads include over-all load factors of 2g, moments of 128,000 pound-feet, and maximum local pressures greater than 40 pounds per square inch. Experimental over-all loads are approximately one-half the design values, while local pressures are of the same order as or larger than pressures calculated from specifications for plating, stringer, floor, and frame design. The value of this comparison is limited, to some extent, by the moderate conditions of the test and by the necessary simplifying assumptions used in comparing the specifications with the experimental loads.

Smiley, Robert F.↗

Distributed Load Shedding Application Architecture and Bi-Level Predictive Estimator Algorithm

Increasing penetrations of distributed renewables are decreasing the effectiveness of traditional decentralized under-frequency load shedding (UFLS) schemes. As more distribution circuits begin to back-feed the transmission system, operation of traditional UFLS may exacerbate frequency instability. This paper presents the conceptual framework for a data-rich environment to coordinate UFLS across multiple distribution providers based on the laminar coordination framework in order to ensure optimal adaptive setting of UFLS relays. Communication and control are enabled through a distributed implementation of the IEC 61968-1 Common Information Model message bus structure. In addition to the proposed architecture, a novel adaptive UFLS scheme informed by a bi-level state estimator to create optimal relay setpoints is introduced. Initial simulation results are presented for the IEEE 14-bus test system on scenarios leading to mis-operation of traditional UFLS.

Anderson, Alexander A.↗

T&D LIBRA: Simulation Framework for Transmission and Distribution Load and IBR Assessment

This paper introduces T&D LIBRA, a HELICS-based dynamic co-simulation framework designed for transmission and distribution (T&D) load and inverter-based resource assessment. This framework is designed to model interactions between single-phase induction motors (i.e., Motor-D), distributed energy resources (DERs) and the transmission network, emphasizing system stability during fault conditions. The primary objective of this research is to study the fault-induced delayed voltage recovery (FIDVR) behavior of the T&D networks using the co-simulation framework and to compare the results with conventional PSS/E only simulations. Simulations are validated using T&D co-simulations with a single distribution node and the IEEE 123-bus distribution test case. The co-simulation results demonstrate the value of using T&D co-simulations to capture motor stalling, DER tripping and other sources of voltage diversity on distribution networks.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Overcoming the Technical Challenges of Coordinating Distributed Load Resources at Scale (Final Report)

Significant recent research has investigated the potential for loads to provide balancing services to the grid. However, this research has not addressed key issues that may arise when such schemes are applied at scale including: 1. Distribution Network Issues. Coordination of large numbers of loads could result in power flows that violate distribution network constraints; 2. Stability Issues. Certain strategies to control loads can exhibit nonlinearity in the form of period-adding bifurcations and chaos. Other control strategies can potentially synchronize the behavior of large numbers of loads. In both cases, the outcome can be power oscillations and instability; 3. Communication Network Issues. Bidirectional low-latency communication channels between a central controller (or several distributed controllers) and each resource are expensive and likely not necessary for effective coordination. Our research questions were: What network, stability, and communication issues might arise in practice when we coordinate large aggregations of loads? How can we coordinate loads to achieve performance objectives in a cost effective manner while avoiding these issues? The ultimate technical goal of the project was the development of network-aware, communication-constrained, non-disruptive load control strategies with stability guarantees that achieve the performance requirements of typical balancing services at a sufficiently low cost to enable the load aggregator and customer to profit. The overall goal was to establish credibility for load control at scale and contribute to U.S. energy security and environmental goals. The team succeeded in answering these research questions and developing these control strategies. The overall approach was based on the development of three testing environments: a simulation testbed, an experimental testbed (20 physical model houses with window-box air conditioners) coupled with the simulation testbed, and a field testbed (100 actual homes in Austin, TX) coupled with the simulation testbed, which enabled controller testing, identification of issues, controller development, and controller validation. The resulting controller was used to demonstrate fast timescale grid balancing (frequency regulation) by aggregations of physical and virtual air conditioners, with sufficient quality to participate in the electricity market. Cost benefit analysis showed overall benefits to the participating households, load aggregators, and the grid, especially if the control technology was integrated directly into existing programmable communicating thermostats. The project provides a variety of wider benefits. Our technology transfer and outreach activities lead us to choose an open-source licensing commercialization pathway, enabling the project results to be available to researchers, industry, and the public. Furthermore, new grid balancing technologies will increase grid flexibility and will enable higher penetrations of intermittent renewable energy resources, such as wind and solar, to be connected to the grid, reducing its environmental impact, and mitigating climate change to the benefit of society.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Load distributions in photoeleastic bolted-joint models

An attempt is made to study the stresses in multiple-bolt connectors, focusing on the stress distribution in a two-pin connector, the two pins being in line and in parallel with the direction of the applied load. The photoelastic modeling approach with two-dimensional transmission photoelasticity is used. The joint models and model fringe patterns are discussed, with special attention given to the existence of a photoelastic isotropic point and to the separation of stresses.

Hyer, M. W.↗

Mobility power flow analysis of an L-shaped plate structure subjected to distributed loading

An analytical investigation based in the Mobility Power Flow (MPF) method is presented for the determination of the vibrational response and power flow for two coupled flat plate structures in an L-shaped configuration, subjected to distributed excitation. The principle of the MPF method consists of dividing the global structure into a series of subsystems coupled together using mobility functions. Each separate subsystem is analyzed independently to determine the structural mobility functions for the junction and excitation locations. The mobility functions, together with the characteristics of the junction between the subsystems, are then used to determine the response of the global structure and the MPF. In the considered coupled plate structure, MPF expressions are derived for distributed mechanical excitation which is independent of the structure response. However using a similar approach with some modifications excitation by an acoustic plane wave can be considered. Some modifications are required to deal with the latter case are necessary because the forces (acoustic pressure) acting on the structure are dependent on the response of the structure due to the presence of the scattered pressure.

Cuschieri, J. M.↗

Improved load distribution in parallel sparse Cholesky factorization

Compared to the customary column-oriented approaches, block-oriented, distributed-memory sparse Cholesky factorization benefits from an asymptotic reduction in interprocessor communication volume and an asymptotic increase in the amount of concurrency that is exposed in the problem. Unfortunately, block-oriented approaches (specifically, the block fan-out method) have suffered from poor balance of the computational load. As a result, achieved performance can be quite low. This paper investigates the reasons for this load imbalance and proposes simple block mapping heuristics that dramatically improve it. The result is a roughly 20% increase in realized parallel factorization performance, as demonstrated by performance results from an Intel Paragon system. We have achieved performance of nearly 3.2 billion floating point operations per second with this technique on a 196-node Paragon system.

Rothberg, Edward↗

Calculation of the distributed loads on the blades of individual multiblade propellers in axial flow using linear and nonlinear lifting surface theories

In recent years much attention has been given to the development of methods and programs for the calculation of the aerodynamic characteristics of multiblade, saber-shaped air propellers. Most existing methods are based on the theory of lifting lines. Elsewhere, the theory of a lifting surface is used to calculate screw and lifting propellers. In this work, methods of discrete eddies are described for the calculation of the aerodynamic characteristics of propellers using the linear and nonlinear theories of lifting surfaces.

Pesetskaya, N. N.↗