Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOW TEMPERATURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An Experimental and Numerical Investigation to Characterize the Low-Temperature Heat Release in Stoichiometric and Lean Combustion

This work reports on an experimental and modeling study on the low-temperature heat release (LTHR) characteristics for three RON 90 binary blends (n-heptane blended with isooctane, toluene and ethanol) in a Cooperative Fuel Research (CFR) engine at lean and stoichiometric conditions that are representative of homogeneous charge compression ignition (HCCI) and spark-ignition (SI) end-gas combustion conditions, respectively. An analysis of the end-gas temperature-pressure (T-P) trajectories was performed to identify the intake conditions leading to similar T-P trajectories between the two lambdas for each fuel blend. A heat release analysis was then conducted for the identified cases, where fuel-to-fuel differences in LTHR were identified and found to be sensitive to the operating condition. Simulations were conducted for these cases using a recently updated chemical kinetic model and a 0-D engine model, where good qualitative and reasonable quantitative agreements in LTHR were obtained. Sensitivity analysis was also performed directly on the rates of LTHR, to understand the controlling chemical reactions of LTHR, providing further insights into the fuel-to-fuel differences. The results demonstrate the significant promoting effect of n-heptane on LTHR rates, while inhibiting effects were seen for ethanol and toluene. Also highlighted was the importance of H atom abstraction reactions from the chemistry of each fuel component, which could lead to contradictory fuel behavior depending on the locations of the H site of the abstraction reaction due to the different ensuing pathways for the primary fuel radicals.

LTHR, RON 90 binary blends, sensitivity analysis↗
DOE OSTI2022

A New Low-Temperature Approach for Efficient and Low-Cost Group V Doping in CdTe Thin Film Solar Cells (Final Technical Report)

The goal of this project is to develop a highly efficient low-temperature ex-situ Group V diffusion doping approach in the CdCl 2 treated polycrystalline CdTe film using the group V chlorides (i.e., PCl 3 , AsCl 3 , SbCl 3 , and BiCl 3 ) as dopants source. For the first time, our innovative doping strategies through the low-temperature ex-situ Group V doping process in polycrystalline CdSeTe successfully demonstrated a promising power conversion efficiency of ~19% compared to the Cu-doped counterparts. Our newly developed low-temperature ex-situ group V doping allows dedicated control of group V diffusion amount, generates a desirable depth profile, and is completely compatible with commercial CdTe module manufacturing. We built the partnership with the largest CdTe solar module manufacturing in the US, e.g., First Solar, Inc to further develop these low-temperature diffusion doped CdSeTe solar cells. Our technology was granted US Patent No. US11257977B2. In this project, we systematically investigate and characterize the new ex-situ group V doping mechanisms, defect chemistry, microstructure, and device physics in CdTe solar cells by combining experimental and theoretical means to pave the way to achieve lower cost toward $\$$0.02/kWh and higher power conversion efficiency (PCE) toward 25% in polycrystalline CdTe solar technology. This project will benefit the public by providing more affordable solar electricity and provide an effective way to address climate change.

14 SOLAR ENERGY↗
DOE OSTI2022

Extending the low-temperature operation of sodium metal batteries combining linear and cyclic ether-based electrolyte solutions

Nonaqueous sodium-based batteries are ideal candidates for the next generation of electrochemical energy storage devices. However, despite the promising performance at ambient temperature, their low-temperature (e.g., < 0 °C) operation is detrimentally affected by the increase in the electrolyte resistance and solid electrolyte interphase (SEI) instability. Here, to circumvent these issues, we propose specific electrolyte formulations comprising linear and cyclic ether-based solvents and sodium trifluoromethanesulfonate salt that are thermally stable down to –150 °C and enable the formation of a stable SEI at low temperatures. When tested in the Na||Na coin cell configuration, the low-temperature electrolytes enable long-term cycling down to –80 °C. Via ex situ physicochemical (e.g., X-ray photoelectron spectroscopy, cryogenic transmission electron microscopy and atomic force microscopy) electrode measurements and density functional theory calculations, we investigate the mechanisms responsible for efficient low-temperature electrochemical performance. We also report the assembly and testing between –20 °C and –60 °C of full Na||Na 3 V 2 (PO 4 ) 3 coin cells. The cell tested at –40 °C shows an initial discharge capacity of 68 mAh g –1 with a capacity retention of approximately 94% after 100 cycles at 22 mA g –1 .

25 ENERGY STORAGE↗
DOE OSTI2026

A high power, low temperature molten sodium battery

Low temperature molten sodium batteries promise low-cost, grid-scale energy storage using earth-abundant materials. To be economically viable, they must demonstrate high current (power) at relevant discharge times. Here a low temperature (135 °C) molten sodium battery with a NaI–AlCl 3 molten salt catholyte and NaSICON separator is explored, minimizing cell ohmic resistances and avoiding precipitation reactions in the molten salt catholyte. Operating currents were increased by as much as 100× compared to the energy-dense baseline design (197 Wh kg −1 and 248 mAh cm −2 ). Cells were cycled 100 times at 50 mA cm −2 (150 mW cm −2 ), averaging 99.8% coulombic efficiency and 79.7% energy efficiency for 30% of the theoretical capacity. Charging currents up to 250 mA cm −2 (1070 mW cm −2 ) are demonstrated for 10% of the theoretical capacity. Toward extending the accessible capacity in these high current systems, the volume ratio of catholyte molten salt to a graphite felt current collector was varied, altering (1) the local current density in the graphite felt and (2) the discharge time at a fixed current density. Optimizing the catholyte : felt ratio dramatically increased capacity utilization to 60% (102 mAh cm −2 ) at 50 mA cm −2 (150 mW cm −2 ) charge and 10 mA cm −2 discharge. This catholyte : felt ratio of 1.4 significantly decreased the cell impedance, minimizing electrode blocking effects seen previously in NaI–AlCl 3 catholytes. Together, these high areal loadings and impressive power outputs demonstrate how low temperature molten sodium batteries can compete with commercialized sodium systems operating at more than twice the temperature.

NaSICON↗
DOE OSTI2024

HydroGEN: Low Temperature Electrolysis

In low temperature electrolysis (LTE), it is imperative to both enhance and explore durability and demonstrate the opportunities for anion exchange membrane-based water electrolysis (AEMWE). The advantage of alkaline-based systems is primarily reduced capital cost: high pH enabling platinum group metal (PGM)-free catalysts and coatings, and the enhanced stability of those components compared to proton exchange membrane (PEM) -based systems. Compared to the water-only fed AEMWE in previous LTE 2.0 work, supporting electrolytes can allow for a significant improvement in performance through higher site-access and stability by reducing utilization and overpotential stresses that lead to catalyst layer delamination.

HYDROGEN↗