Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift to Drag Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Aerodynamic characteristics of some modified conical bodies with low lift-drag ratios at Mach numbers of 2.30 and 4.63

A wind-tunnel investigation was conducted at Mach numbers of 2.30 and 4.63 to determine the static aerodynamic characteristics of three 60 deg half-angle cone models. Configuration 1 was obtained by raking off a symmetrical cone at a base angle of 6.15 deg, and configuration 2 and 3 were obtained by adding flaps to a symmetrical cone. The models were tested at angles of attack from about -5 deg to about 20 deg at roll angles of 0 deg to -180 deg and at a freestream Reynolds number of 1.09 x one million, based on body diameter. The results showed that all three configurations produced finite values of lift-drag ratio useful for lifting planetary entry. All three configurations exhibited increases in yawing moment and side force with roll angle; thus, the capability for lateral trajectory control is provided.

Davenport, E. E.↗

LATERAL-RANGE AND HYPERSONIC LIFT-DRAG-RATIO REQUIREMENTS FOR EFFICIENT FERRY SERVICE FROM A NEAR-EARTH MANNED SPACE STATION

The operation of any long-term manned space station will require some type of ferry vehicle to transport men and equipment to and from the station with regularity and reliability. Such a vehicle, designed for entry at near-orbital speeds, could also be useful in the return from any deeper space mission if either an earth-orbit rendezvous terminal maneuver or a maneuver combining atmospheric braking and a near-earth parking orbit is used. This study was undertaken to determine the class of vehicle which could be most efficiently used as a ferry vehicle between a near-earth space station and the earth. One measure of this efficiency is the ability of the vehicle to reach pre-chosen landing sites with some prescribed frequency. In considering this frequency of return it is necessary to consider not only the normal mode of operation in which only infrequent returns are scheduled at desirable times, but also operation under various degrees of emergency, which dictate quick or even immediate return to earth. In extreme emergencies, when immediate return to earth is necessary, choice of landing site becomes impractical. In most cases, however, although it might be required to abandon the station quickly, the ferry vehicle could remain in orbit for some time before initiating reentry in order to land at a prechosen site. The allowable delay time in orbit would be determined primarily by the capabilities of the ferry life-support system. This paper will examine the geometry of the ferry ranging problem, that is, the lateral ranges required to reach chosen landing sites from various near-earth orbits, and will investigate and compare several means of achieving these ranges. The particular case considered is that of returning from a space station which is in a circular orbit at an altitude of 200 statute miles, but the results obtained are not sensitive to orbit altitude for orbits within a few hundred miles of the surface. From this orbit, the vehicle will retro and reenter at very close to satellite velocity. The downrange problem can be handled by proper timing of the retrofiring , and the desired lateral range can be achieved by aerodynamics, space propulsion to change orbit plane, atmospheric propulsion, or combinations of these methods. The relative cost in terms of weight of using these different methods to achieve lateral range will be discussed.

Hypersonic vehicle↗

Investigation of Minimum Drag and Maximum Lift-drag Ratios of Several Wing-body Combinations Including a Cambered Triangular Wing at Low Reynolds Numbers and at Supersonic Speeds

Theoretical and experimental data for wing-body combinations with wings of triangular, arrow, and diamond plan form are presented for Mach numbers of 1.62, 1.93, and 2.41 and a Reynolds number range of 1.4 x 10 to the 6th power to 0.7 x 10 to the 6th power. Included are two each of triangular and arrow plan-form wings cambered for approximately uniform load at m = 1.62 and lift coefficients of 0.08 and 0.20. Liquid-film studies of the flow over the various configurations are also presented.

Brown, Clinton E↗

Preliminary wind-tunnel investigation of the effects of engine nacelles on a transport configuration with high lift drag ratios to a Mach number of 1.00

Wind tunnel tests to determine the effect of engine nacelles added to a low wing fuselage vertical tail configuration utilizing the NASA supercritical airfoil and a refined area ruled fuselage are discussed. The engine arrangement consisted of two aft fuselage, side mounted flow through nacelles and a solid body of revolution mounted above the fuselage in a manner similar to the Boeing 727. A preliminary analysis of the wind tunnel data shows that favorable interference drag can be obtained with the proper longitudinal locations of the nacelles, by canting the nacelle inlets, and by cusping the rearward region of the nacelle.

Flechner, S. G.↗