SEARCH · Search NASA

Results for “Liquid fragility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

24 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Lessons Learned from the Stardust Sample Return Mission

These are science and mission design and operations lessons learned from the Stardust Mission, which returned grains from comet Wild-2 and fresh interstellar dust to Earth in 2006 [1]. Science Lessons: Major discoveries of the Stardust Wild-2 samples include the presence of numerous chondrules and CAI in a comet, which requires a much more dynamic early solar system than many had envisaged, and verified predictions made by models requiring outward flow of early solar system solids before the early nebular gas had dissipated [1-3]. No evidence has been found for the presence of live Al-26 in the comet, suggesting late accretion [4]. Carbonates and unusual sulfides were found which potentially require activity of liquid water within the comet, but to only a minor degree at best [5-6]. The presence of abundant thermally-metamorphosed silicates in Wild-2 appears to require assembly from an earlier generation of bodies [7]. The abundance of presolar grains in the Wild-2 samples appears to be below what has been found in most chondritic IDPs and primitive chondrites [1]. The bulk mineralogy of Wild-2 grains does not match the mineralogy from any single other known astromaterial [7], and is also strikingly unlike that inferred from Spitzer Telescope spectra of Comet Temple 1 dust [8]. Amino acids and other fragile organics have been detected among the Wild-2 samples [9], which highlights the critical importance of further developing techniques for organic analysis in small samples, and cleaning outbound spacecraft.

Zolensky, M. E.↗

NASA NTRSDate not supplied

Ryugu-Like Phyllosilicate Clast from A Giant Cluster IDP of Probable Cometary Origin: Evidence for Material Exchange Between Asteroidal and Cometary Regions

The presence of hydrous minerals in comets is currently an open question. They were commonly produced inside primitive meteorite parent bodies but apparently not inside the active comets that never contained liquid water. Despite examination of hundreds of particles returned from the Jupiter Family comet Wild 2 by the Stardust(SD) spacecraft, no phyllosilicates have yet been found. Near IR spectra obtained by the Rosetta spacecraft of short-period comet 67P Churyumov-Gerasimenko (67P CG) similarly did not reveal the presence of phyllosilicate minerals. IR spectral features in ejecta from comet Temple 1were interpreted as hydrated minerals but this match is controversial. Studies of a giant cluster interplanetary dust particle (IDP) have demonstrated that the IDP has a large number of chemical and physical properties consistent with its derivation from a comet including 1) its porous aggregate morphology similar to fragile aggregate particles imaged from comet 67P CG, 2) an unequilibrated mineral assemblage, 3) mineral isotopic compositions similar to like minerals in comet Wild 2, 4) uncorrelated Fe-Mn ratios of olivines that mimic those from Wild 2, 5) high presolar silicate abundance [8] and 6) Kool grains which are observed in comet Wild 2 but not in chondrites. Our examination of 70+>5 μm fragments from the IDP have shown that it is overwhelmingly composed of anhydrous silicates. We have observed, however, a 5 x 15 μm porous aggregate fragment (LT10), which contains a rare phyllosilicate clast encased in anhydrous mineral and rock fragments. We conducted detailed TEM and O isotopic analyses of this particle to constrain its origin.

D J Joswiak↗

NASA NTRS1997

Application of NASA's Advanced Life Support Technologies in Polar Regions

The problems of obtaining adequate pure drinking water and disposing of liquid and solid waste in the U.S Arctic, a region where virtually all water is frozen solid for much of the year, has led to unsanitary solutions. Sanitation and a safe water supply are particularly problems in rural villages. These villages are without running water and use plastic buckets for toilets. The outbreak of diseases is believed to be partially attributable to exposure to human waste and lack of sanitation. Villages with the most frequent outbreaks of disease are those in which running water is difficult to obtain. Waste is emptied into open lagoons, rivers, or onto the sea coast. It does not degrade rapidly and in addition to affecting human health, can be harmful to the fragile ecology of the Arctic and the indigenous wildlife and fish populations. Current practices for waste management and sanitation pose serious human hazards as well as threaten the environment. NASA's unique knowledge of water/wastewater treatment systems for extreme environments, identified in the Congressional Office of Technology Assessment report entitled An Alaskan Challenge: Native Villagt Sanitation, may offer practical solutions addressing the issues of safe drinking water and effective sanitation practices in rural villages. NASA's advanced life support technologies are being combined with Arctic science and engineering knowledge to address the unique needs of the remote communities of Alaska through the Advanced Life Systems for Extreme Environments (ALSEE) project. ALSEE is a collaborative effort involving the NASA, the State of Alaska, the University of Alaska, the North Slope Borough of Alaska, Ilisagvik College in Barrow and the National Science Foundation (NSF). The focus is a major issue in the State of Alaska and other areas of the Circumpolar North; the health and welfare of its people, their lives and the subsistence lifestyle in remote communities, economic opportunity, and care for the environment. As advanced technologies are transferred to the commercial sector the ALSEE project Offers the potential for development of new industries in Alaska to supply the products to support remote communities of the globe.

Bubenheim, David L.↗

NASA NTRS2005

Lightweight Thermal Insulation for a Liquid-Oxygen Tank

A proposed lightweight, reusable thermal-insulation blanket has been designed for application to a tank containing liquid oxygen, in place of a non-reusable spray-on insulating foam. The blanket would be of the multilayer-insulation (MLI) type and equipped with a pressure-regulated nitrogen purge system. The blanket would contain 16 layers in two 8-layer sub-blankets. Double-aluminized polyimide 0.3 mil (.0.008 mm) thick was selected as a reflective shield material because of its compatibility with oxygen and its ability to withstand ionizing radiation and high temperature. The inner and outer sub-blanket layers, 1 mil (approximately equals 0.025 mm) and 3 mils (approximately equals 0.076 mm) thick, respectively, would be made of the double-aluminized polyimide reinforced with aramid. The inner and outer layers would provide structural support for the more fragile layers between them and would bear the insulation-to-tank attachment loads. The layers would be spaced apart by lightweight, low-thermal-conductance netting made from polyethylene terephthalate.

Willen, G. Scott↗

NASA NTRS1995

Advanced Life Systems for Extreme Environments: An Arctic Application

The problems of obtaining adequate pure drinking water and disposing of liquid and solid waste in the U.S. Arctic, a region where virtually all water is frozen solid for much of the year, has led to unsanitary solutions (U.S. Arctic Research Commission). These solutions are also damaging to the environment. Sanitation and a safe water supply are particularly problems in rural villages. About one-fourth of Alaska's 86.000 Native residents live in these communities. They are without running water and use plastic buckets for toilets. The outbreak of diseases is believed to be partially attributable to exposure to human waste. Villages with the most frequent outbreaks of disease are those in which running water is difficult to obtain (Office of Technology Assessment, 1994). Waste is emptied into open lagoons, rivers, or onto the sea coast. It does not degrade rapidly and in addition to affecting human health, can be harmful to the fragile ecology of the Arctic and the indigenous wildlife and fish populations. Advanced Life Systems for Extreme Environments (ALSEE) provides a solution to sanitation and safe water problems. The system uses an advanced integrated technology developed for Antarctic and space applications. ALSEE uses the systems approach to address more than waste and water problems. By incorporating hydroponic horticulture and aquaculture into the waste treatment system, ALSEE addresses the quality and quantity of fresh foods available to Arctic residents. A temperate climate is required for year-round plant growth. ALSEE facilities can be designed to include a climate controlled area within the structure. This type of environment is a change from the long periods of darkness and cold found in the Arctic and can help alleviate stress so often associated with these extremes. While the overall concept of ALSEE projects is advanced, system facilities can be operated by village residents with appropriate training. ALSEE provides continuing training and education as a part of the project. Not only is this desirable but necessary. There is ample evidence in "gravoyard" throughout rural Alaska of technologies which failed not because they were not applic4tble, but because they were not integrated and could not be operated or repaired by village residents. Waste streams in villages will vary depending on the human diet and the non-food waste stream. ALSEE units can be adapted to different village situations once the content of the waste stream is known. Units located in population hubs can serve as research, education. and demonstration centers. Appropriate modifications can be determined at these centers to transfer technology to more remote locations where waste stream conditions may differ.

Lewis, Carol E.↗

NASA NTRS2012

Focal Plane Alignment Utilizing Optical CMM

In many applications, an optical detector has to be located relative to mechanical reference points. One solution is to specify stringent requirements on (1) mounting the optical detector relative to the chip carrier, (2) soldering the chip carrier onto the printed circuit board (PCB), and (3) installing the PCB to the mechanical structure of the subsystem. Figure 1 shows a sketch of an optical detector mounted relative to mechanical reference with high positional accuracy. The optical detector is typically a fragile wafer that cannot be physically touched by any measurement tool. An optical coordinate measuring machine (CMM) can be used to position optical detectors relative to mechanical reference points. This approach will eliminate all requirements on positional tolerances. The only requirement is that the PCB is manufactured with oversized holes. An exaggerated sketch of this situation is shown in Figure 2. The sketch shows very loose tolerances on mounting the optical detector in the chip carrier, loose tolerance on soldering the chip carrier to the PCB, and finally large tolerance on where the mounting screws are located. The PCB is held with large screws and oversized holes. The PCB is mounted loosely so it can move freely around. The optical CMM measures the mechanical reference points. Based on these measurements, the required positions of the optical detector corners can be calculated. The optical CMM is commanded to go to the position where one detector corner is supposed to be. This is indicated with the cross-hairs in Figure 2(a). This figure is representative of the image of the optical CMM monitor. Using a suitable tapping tool, the PCB is manually tapped around until the corner of the optical detector is at the crosshairs of the optical CMM. The CMM is commanded to another corner, and the process is repeated a number of times until all corners of the optical detector are within a distance of 10 to 30 microns of the required position. The situation is sketched in Figure 2(b) (the figure also shows the tapping tool and where to tap). At this point the fasteners for the PCB are torqued slightly so the PCB can still move. The PCB location is adjusted again with the tapping tool. This process is repeated 3 to 4 times until the final torque is achieved. The oversized mounting holes are then filled with a liquid bonding agent to secure the board in position (not shown in the sketch). A 10- to 30-micron mounting accuracy has been achieved utilizing this method..

Liebe, Carl Christian↗