Search NASA⌕ Search

SEARCH · Search NASA

Results for “Longitudinal dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1924

A study of longitudinal dynamic stability in flight

This investigation was carried out by the aerodynamic staff of the National Advisory Committee for Aeronautics for the purpose of studying experimentally the longitudinal dynamic stability of airplanes in flight. The airplanes selected for this purpose were a standard rigged VE-7 advanced-training airplane and a JN4H with special tail surfaces. The airplanes were caused to oscillate by means of the elevator, then the longitudinal control was either locked or kept free while the oscillation died out. The magnitude of the oscillation was recorded either by a kymograph or an airspeed meter. The results show that the engine speed has as much effect on the period and damping as the airspeed, and that, contrary to theory as developed for small oscillations, the damping decreased at the higher airspeeds with closed throttle.

Norton, F H↗
NASA NTRS1992

New literal approximations for the longitudinal dynamic characteristics of flexible flight vehicles

The goal of the literal approximation method is to obtain simple literal (analytical) approximations for key dynamic characteristics of flexible flight vehicles. A basic question regarding the method is its usefulness as an additional design tool for existing design and simulation procedures. Two aspects of this question are: (1) ease of derivation and use of the literal approximations, and (2) the suitability of one set of literal approximations to describe the dynamics of a large set of significantly different vehicles. These issues are addressed by incorporating symbolic manipulation software into the literal approximation method for the analysis of a fifth order model of the longitudinal dynamics of a flexible flight vehicle. The automated literal approximation generated in this fashion reduces the manual derivation time by an approximate factor of four. A single set of literal approximations is shown to provide adequate approximations for the dynamics of significantly different flight vehicles configurations, such as an aircraft, a missile, and a hypersonic vehicle.

Livneh, Rafael↗
NASA NTRS1946

Flight Investigation to Improve the Dynamic Longitudinal Stability and Control-Feel Characteristics of the P-63A-1 Airplane (AAF No. 42-68889) with Closely Balanced Experimental Elevators

Results of flight tests of a control-feel aid presented. This device consisted of a spring and dashpot connected in series between the control stick and airplane structure. The device was tested in combination with an experimental elevator and bobweight which had given unsatisfactory dynamic stability and control-feel characteristics in previous tests. The control-feel aid effected marked improvement in both the control-feel characteristics and the control-feel dynamic longitudinal stability of the airplane.

AIRPLANES - BELL P-63A-1 FLIGHT TESTS (AMER )↗
DOE OSTI2022

Longitudinal dynamics and particle production in relativistic nuclear collisions

This work presents a three-dimensional dynamical initialization model for relativistic heavy-ion collisions, implementing local energy-momentum conservation and baryon charge fluctuations at string junctions. Constraining parameters using experimental data from p + p collisions at various collision energies, the model provides a very good description of the charged hadron and net proton rapidity distributions in Au +Au collisions from 7.7 to 200 GeV and Pb + Pb collisions at 8.77 and 17.3 GeV. Here we demonstrate the importance of fluctuations of baryon densities to string junctions for describing net-proton distributions at collision energies of 62.4 and 200 GeV. Including this improved baryon stopping description along with the requirement of strangeness neutrality also yields a good description of identified particle yields as functions of the collision energy above 7.7 GeV. We further study asymmetric p + Al and (p,d, 3 He) + Au collisions at the top RHIC energy and p + Pb, Xe + Xe, and Pb + Pb collisions at LHC energies. We identify the produced particle rapidity distributions in asymmetric collision systems as particularly useful for constraining models of the early-time longitudinal dynamics.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Start-to-End Simulation of the Drive-Beam Longitudinal Dynamics for Beam-Driven Wakefield Acceleration

Collinear beam-driven wakefield acceleration (WFA) relies on shaped driver beam to provide higher accelerating gradient at a smaller cost and physical footprint. This acceleration scheme is currently envisioned to accelerate electron beams capable of driving free-electron laser *. Start-to-end simulation of drive-bunch beam dynamics is crucial for the evaluation of the design of accelerators built upon WFA. We report the start-to-end longitudinal beam dynamics simulations of an accelerator beamline capable of producing high charge drive beam. The generated wakefield when it passes through a corrugated waveguide results in a transformer ratio of 5. This paper especially discusses the challenges and criteria associated with the generation of temporally-shaped driver beam, including the beam formation in the photoinjector, and the influence of energy chirp control on beam transport stability.

43 PARTICLE ACCELERATORS↗
DOE OSTI2017

The use of BMAD in simulating transverse and longitudinal dynamics in RHIC

In accelerator physics, models of a given machine are used to predict the behaviors of the beam, magnets, and radiofrequency cavities. The use of the computational model has become wide spread to ease the development period of the accelerator lattice. There are various programs that are used to create lattices and run simulations of both transverse and longitudinal beam dynamics. The programs include Methodical Accelerator Design(MAD) MAD8, MADX, Zgoubi, Polymorphic Tracking Code (PTC), and many others. In this discussion the BMAD (Baby Methodical Accelerator Design) is presented as an additional tool in creating and simulating accelerator lattices for the study of beam dynamics in the Relativistic Heavy Ion Collider (RHIC).

43 PARTICLE ACCELERATORS↗
NASA NTRS1957

Analog-computer investigation of effects of friction and preload on the dynamic longitudinal characteristics of a pilot-airplane combination

With an electric analog computer, an investigation has been made of the effects of control frictions and preloads on the transient longitudinal response of a fighter airplane during abrupt small attitude corrections. The simulation included the airplane dynamics, powered control system, feel system, and a simple linearized pseudopilot. Control frictions at the stick pivot and at the servo valve as well as preloads of the stick and valve were considered individually and in combinations. It is believed that the results which are presented in the form of time histories and vector diagrams present a more detailed illustration of the effects of stray forces and compensating forces in the longitudinal control system than has previously been available. Consistent with the results of previous studies, the present results show that any of thesefour friction and preload forces caused some deterioration of the response. However, even a small amount of valve friction caused an oscillatory pitching response during which the phasing of the valve friction was such that it caused energy to be fed into the pitching oscillation of the airplane. Of the other friction and preload forces which were considered, it was found that stick preload was close to 180 degrees out of phase with valve friction and thus could compensate in large measure for valve friction as long as the cycling of the stick encompassed the trim point. Either stick friction or valve preload provided a smaller stabilizing effect primarily through a reduction in the amplitude of the resultant force vector acting on the control system. Some data were obtained on the effects of friction when the damping or inertia of the control system or the pilot lag was varied.

Crane, Harold L↗
NASA NTRS1961

Analog-Computer Investigation of Effects of Friction and Preload on the Dynamic Longitudinal Characteristics of a Pilot-Airplane Combination

With an electric analog computer, an investigation has been made of the effects of control frictions and preloads on the transient longitudinal response of a fighter airplane during abrupt small attitude corrections. The simulation included the airplane dynamics, powered control system, feel system, and a simple linearized pseudopilot. Control frictions at the stick pivot and at the servo valve as well as preloads of the stick and valve were considered individually and in combinations. It is believed that the results which are presented in the form of time histories and vector diagrams present a more detailed illustration of the effects of stray forces and compensating forces in the longitudinal control system than has previously been available. Consistent with the results of previous studies, the present results show that any of these four friction and preload forces caused some deterioration of the response. However, even a small amount of valve friction caused an oscillatory pitching response during which the phasing of the valve friction was such that it caused energy to be fed into the pitching oscillation of the air-plane. Of the other friction and preload forces which were considered, it was found that stick preload was close to 180 deg. out of phase with valve friction and thus could compensate in large measure for valve friction as long as the cycling of the stick encompassed the trim point. Either stick friction or valve preload provided a smaller stabilizing effect primarily through a reduction in the amplitude of the resultant force vector acting on the control system. Some data were obtained on the effects of friction when the damping or inertia of the control system or the pilot lag was varied.

Crane, Harold L.↗
NASA NTRS1959

Dynamic Longitudinal and Directional Stability Derivatives for a 45 deg. Sweptback-Wing Airplane Model at Transonic Speeds

An investigation was made at transonic speeds to determine some of the dynamic stability derivatives of a 45 deg. sweptback-wing airplane model. The model was sting mounted and was rigidly forced to perform a single-degree-of-freedom angular oscillation in pitch or yaw of +/- 2 deg. The investigation was made for angles of attack alpha, from -4 deg. to 14 deg. throughout most of the transonic speed range for values of reduced-frequency parameter from 0.015 to 0.040 based on wing mean aerodynamic chord and from 0.04 to 0.14 based on wing span. The results show that reduced frequency had only a small effect on the damping-in-pitch derivative and the oscillatory longitudinal stability derivative for all Mach numbers M and angles of attack with the exception of the values of damping coefficient near M = 1.03 and alpha = 8 deg. to 14 deg. In this region, the damping coefficient changed rapidly with reduced frequency and negative values of damping coefficient were measured at low values of reduced frequency. This abrupt variation of pitch damping with reduced frequency was a characteristic of the complete model or wing-body-vertical-tail combination. The damping-in-pitch derivative varied considerably with alpha and M for the horizontal-tail-on and horizontal-tail-off configurations, and the damping was relatively high at angles of attack corresponding to the onset of pitch-up for both configurations. The damping-in-yaw derivative was generally independent of reduced frequency and M at alpha = -4 deg. to 4 deg. At alpha = 8 deg. to 14 deg., the damping derivative increased with an increase in reduced frequency and alpha for the configurations having the wing, whereas the damping derivative was either independent of or decreased with increase in reduced frequency for the configuration without the wing. The oscillatory directional stability derivative for all configurations generally decreased with an increase in the reduced-frequency parameter, and, in some instances, unstable values were measured for the model configuration with the horizontal tail removed.

Bielat, Ralph P.↗
DOE OSTI2021

Probing early-time longitudinal dynamics with the Λ hyperon's spin polarization in relativistic heavy-ion collisions

Here, we systematically study the hyperon global polarization's sensitivity to the collision systems' initial longitudinal flow velocity in hydrodynamic simulations. By explicitly imposing local energy-momentum conservation when mapping the initial collision geometry to macroscopic hydrodynamic fields, we study the evolution of systems' orbital angular momentum (OAM) and fluid vorticity. We find that a simultaneous description of the $\Lambda$ hyperons' global polarization and the slope of pion's directed flow can strongly constrain the size of longitudinal flow at the beginning of hydrodynamic evolution. We extract the size of the initial longitudinal flow and the fraction of orbital angular momentum in the produced QGP fluid as a function of collision energy with the STAR measurements in the RHIC Beam Energy Scan program. We find that there is about 100-200 $\hbar$ OAM that remains in the mid-rapidity fluid at the beginning of hydrodynamic evolution. We further exam the effects of different hydrodynamic gradients on the spin polarization of $\Lambda$ and $\bar{\Lambda}$. The gradients of $\mu_B/T$ can change the ordering between $\Lambda$'s and $\bar{\Lambda}$'s polarization.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2016

Modeling Longitudinal Dynamics in the Fermilab Booster Synchrotron

The PIP-II project will replace the existing 400 MeV linac with a new, CW-capable, 800 MeV superconducting one. With respect to current operations, a 50% increase in beam intensity in the rapid cycling Booster synchrotron is expected. Booster batches are combined in the Recycler ring; this process limits the allowed longitudinal emittance of the extracted Booster beam. To suppress eddy currents, the Booster has no beam pipe; magnets are evacuated, exposing the beam to core laminations and this has a substantial impact on the longitudinal impedance. Noticeable longitudinal emittance growth is already observed at transition crossing. Operation at higher intensity will likely necessitate mitigation measures. We describe systematic efforts to construct a predictive model for current operating conditions. A longitudinal only code including a laminated wall impedance model, space charge effects, and feedback loops is developed. Parameter validation is performed using detailed measurements of relevant beam, rf and control parameters. An attempt is made to benchmark the code at operationally favorable machine settings.

43 PARTICLE ACCELERATORS↗
NASA NTRS1996

Navier-Stokes Simulation of the Canard-Wing-Body Longitudinal Dynamic Stability Characteristics

Many modern aircraft are canard-configured for aircraft control and improved aerodynamic performance. Canards can often enhance aircraft cruise performance, maneuverability and agility. For close-coupled canard configurations, the aerodynamic interaction between the canard and wing significantly changes the flow characteristics of the wing. In unsteady flow, such changes in the flow structure and performance of wings can be quite pronounced. Accurate modeling of the unsteady aerodynamics is essential for potential CFD design and analysis of such configurations. A time-accurate numerical simulation is performed to study the unsteady aerodynamic interaction between a canard and wing with emphasis on the effects of the canard on the configuration's dynamic response characteristics. The thin-layer Reynolds-averaged Navier-Stokes Equations with various turbulence models are used in this study. Computations are made on a generic, analytically-defined, close-coupled canard-wing-body configuration which has been the subject of numerous previously published experimental studies during the 1970's to mid-80's. More recently, a series of steady-flow simulations has been performed and published by the author. In the current study, the configuration is given prescribed ramp and oscillatory motions in order to predict characteristics such as the damping-in-pitch and oscillatory longitudinal stability parameters. The current computations are made at high-subsonic and transonic Mach numbers, moderate angles-of- attack from -4 to 20 degrees, and at various pitch rates and reduced frequencies. Comparisons of pressures and integrated force quantities (e.g. lift, drag, pitching moment and selected dynamic parameters) are made with other published computational results and available experimental data. Results showing the unsteady effects of the canard on surface pressures, integrated forces, canard-wing vortex interaction and vortex breakdown will be presented.

Tu, Eugene L.↗
DOE OSTI2018

Longitudinal dynamics of high baryon density matter in high-energy heavy-ion collisions

In high-energy heavy-ion collisions, the two colliding nuclei pass through each other leaving behind an almost baryon-free central rapidity region. Most of the baryons are carried away by the nuclear remnants and are located in the so-called fragmentation regions. In previous papers, it has been argued that very high baryon densities, more than ten times larger than the normal nuclear density, can be achieved in these fragmentation regions. In this paper, we assume the high baryon density matter is thermalized at the same time as the baryon-free quark-gluon plasma in the central rapidity region. We perform a 1+1D (temporal + longitudinal) hydrodynamic simulation covering both the fragmentation regions and the central rapidity region with the baryon diffusion equation included. Baryons are found to diffuse from the fragmentation regions to the central rapidity region driven by fugacity gradients. Here, the baryon chemical potential at freezeout monotonically increases from the central rapidity region to the fragmentation regions, suggesting a rapidity scan in high-energy heavy-ion collisions might be helpful in searching for the critical point of the quantum chromodynamics phase diagram.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗