Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low Reactivity Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Additive-Mixing Fuel Injection (AMFI): A device for robust control and improved performance of high-efficiency LTGC engines

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and particulate emissions. Despite these major advantages, methods for controlling LTGC combustion timing, achieving robust autoignition, and good low-load performance have challenged the development of practical LTGC engines. A key reason is that the ideal reactivity of the fuel varies with operating conditions, with low-reactivity fuels working well at high loads and higher-reactivity fuels working better at low loads. This article introduces a new technique called Additive Mixing Fuel Injection (AMFI) that adjusts the reactivity of the gasoline to obtain good performance over the operating map. Moreover, AMFI can provide robust combustion-timing control because it precisely meters very small amounts (0.01–0.6 mm 3 ) of an ignition-enhancing additive into the fuel each engine cycle. The additive used was 2-ethylhexyl nitrate (EHN), a common, inexpensive diesel-fuel ignition improver, but other additives could be used. Because additive amounts are so small, a 2-gal reservoir would be sufficient for medium-duty applications with refilling only at service intervals of about 8000 mi. The AMFI system has been installed on a single-cylinder LTGC research engine and demonstrated to provide robust combustion-timing control over wide ranges of combustion phasing, fueling rate, intake boost, engine speed, and intake temperature. AMFI also increases the fuel’s reactivity sufficiently to greatly reduce or eliminate the need for charge heating, simplifying engine design and significantly increasing thermal efficiency and the maximum load at low-boost conditions. The nitrogen in the EHN produced a modest increase in NOx, but it was mitigated by lower intake temperatures, and NOx emissions remained very low. Finally, the additive increases the sensitivity of autoignition reactions to variations in the local fuel/air mixture within the charge. This allows the use of controlled fuel stratification for improved LTGC-engine performance, and its potential to improve low-load operation was demonstrated.

Dec, John E.↗
DOE OSTI2025

Experimental Studies on Enhanced Ignition for Improved Pre-Chamber Combustion in Gas Engines

Global efforts to reduce greenhouse gas emissions and mitigate climate change have intensified the demand for cleaner and more efficient combustion technologies. Heavyduty engines, which remain essential for transportation and power generation, must operate with significantly lower emissions while maintaining high efficiency and fuel flexibility. Lean combustion and exhaust gas recirculation (EGR) offer promising pathways to reduce emissions and improve thermal efficiency; however, these strategies impose severe challenges for engine operation, especially for low reactivity gaseous fuels like natural gas and ammonia. Pre-chamber combustion has emerged as a viable approach that uses turbulent jets to accelerate main chamber ignition, but its performance can degrade under high dilution or with hard-to-ignite fuels. These limitations motivate the central focus of this dissertation: understanding passive pre-chambers and improving their performance under challenging conditions.

Dhotre, Akash [Univ. of Minnesota, Minneapolis, MN↗
DOE OSTI2022

The influence of thermochemistry on the reactivity of propane, the pentane isomers and $n$-heptane in the low temperature regime

In this study, the influence of thermochemistry on the reactivity of fuels at low temperatures (600–1000 K) is studied here. Specifically, the effect of different sets of thermochemistry on chemical model predictions is explored, where various sets are calculated at different levels of theory in addition to recently updated group additivity values. Experimentally measured ignition delay times for propane, the pentane isomers and n-heptane are simulated using NUIGMech1.2 and replacing the thermochemistry of the low-temperature species with the calculated values. For propane, three different thermochemistry sets were calculated, namely CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//B2PLYP-D3/TZ (QM1), CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//ωB97X-D/TZ (QM2) and B2PLYP-D3/TZ/ωB97X-D/6-31G*//ωB97X-D/6-31G* (QM3). The QM2 results provide parameters to optimize new group additivity (NGA) values which are used to calculate the fourth set of thermochemistry. The model predictions using these four sets are compared to those using NUIGMech1.2 for propane. As the QM1 and QM2 calculations are expensive, the thermochemistry calculated from the QM3 and NGA calculations are used in the pentane isomer and n-heptane models. For all of the models, it is found that the thermochemistry of the species involved in the low-temperature reaction sequence ($RH$, $\dot{R}$, $RO_2H$, $R\dot{O}_2$, $\dot{Q}OOH$ and $\dot{O}_2QOOH$ species) significantly affect fuel reactivity. The NGA values were developed based on all of these species except $\dot{O}_2QOOH$ radicals. The thermochemistry of $\dot{O}_2QOOH$ species cannot be accurately calculated with the NGA representations due to the importance of non-next-nearest neighbor interactions of –OOH substitution. Further development of the NGA method to capture such interactions is in progress. Overall, the model developed using the NGA thermochemistry shows better agreement with experimental data than the model using thermochemistry from affordable and prominent QM methods, such as QM3. Based on the results presented for propane, the pentane isomers and n-heptane, the thermochemistry calculated using the NGA method can be used to model the oxidation of higher order hydrocarbons at low temperatures.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Group additivity values for entropy and heat capacities of C 2 –C 8 alkanes, alkyl hydroperoxides, and their radicals

Group additivity values for the thermodynamic properties of oxygenated radicals are poorly determined due to the absence of high quality reference data. Here, a set of 58 group additive values (GAV) for the standard entropy and heat capacity of relevance to alkane oxidation is derived from fits to an extensive and accurate database of standard entropies (298.15 K) and heat capacities (300–3000 K) recently calculated with the “STAR-1D” formalism. The 192 species in this database represent the alkanes (RH), alkyl radicals ($\dot{R}$), alkyl hydroperoxides (RO 2 H), alkyl-peroxy (R$\dot{O}$ 2 ) and hydroperoxy-alkyl ($\dot{Q}$OOH) radicals for all of the isomers of C 2 –C 5 alkane fuels and a select number of isomers of C 6 –C 9 species. The STAR-1D thermochemical data for this set of species was previously obtained from a coupling of scaled B2PLYPD3/cc-pVTZ vibrational analyses with scaled ωB97X-D/cc-pVTZ one-dimensional hindered rotor corrections. The 2σ uncertainties in the GAV results relative to the STAR-1D data set are 2.4 cal K –1 mol –1 for the entropies and at most 2.0 cal K –1 mol –1 for the heat capacities in the temperature range 500–800 K. The 2σ fitting uncertainties in the heat capacity gradually reduce at higher temperatures reaching a value of 0.8 cal K –1 mol –1 at 2000 K decreasing to only 0.5 cal K –1 mol –1 at 3000 K. The high degree of accuracy for the GAV representations is obtained through the introduction of various new group terms, together with the re-optimization of existing group terms. Among the full set of 58 GAV terms, 25 include non-next-nearest neighbor interactions (NNI) and β-corrections. The updated GAVs can be applied in the prediction of entropies and heat capacities for a wide range of hydrocarbons and hydroperoxide species and their radicals, which is important to the accurate prediction of fuel reactivity at low-temperatures in the range 600–1000 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Influence of gasoline fuel formulation on lean autoignition in a mixed-mode-combustion (deflagration/autoignition) engine

We report stoichiometric spark-ignition engines suffer efficiency penalties due to throttling losses at low loads, a low specific-heat ratio of the stoichiometric working fluid, and limits on compression ratio due to end-gas autoignition leading to undesirable knocking. Mixed-Mode Combustion (MMC) mitigates these shortcomings by using a lean working fluid where a spark-initiated pilot-stabilized deflagrative flame front is followed by controlled end-gas autoignition. This MMC study investigates the effects of initial conditions (intake air temperature, intake pressure, equivalence ratio, and intake oxygen fraction) on autoignition tendency of four gasoline-range fuels with varying properties and composition. The use of fuels with varying octane sensitivity (S) allowed exploring the importance of low-temperature heat release in triggering autoignition. Fuels with high S were less reactive for conditions that promote low-temperature chemistry (operation at high intake air pressure or without N2 dilution). Conversely, an Alkylate fuel with low S showed a greater autoignition resistance at operating conditions that were unfavorable for low-temperature chemistry. Next, the effect of residual gas composition on autoignition tendency of fuels was examined with a chemical-kinetics model. Among the various molecules in the residual gas, nitric oxide (NO) enhanced the low-temperature chemistry and increased the autoignition tendency most significantly. The fuels’ autoignition response to increasing NO amount corroborates the experimental observations. Next, the sequential autoignition of the end-gas was assessed to be less impacted by thermal stratification because of lean mixtures showing relatively less low-temperature chemistry, when compared to stoichiometric mixtures. Next, the effect of changing equivalence ratio on the autoignition was found to be similar for all fuels, regardless of their S. With changing intake air temperature, the response of fuels’ autoignition tendency depended on the dilution level used. At high dilution (i.e. low intake [O2]), fuels’ reactivity increased with increasing intake air temperature. In contrast, for operation without dilution, the autoignition tendency of the low-S Alkylate fuel decreased with increasing intake air temperature, while that of high-S High Cycloalkane fuel still increased with increasing intake air temperature. In conclusion, conventional octane metrics (RON and MON) have utility in assessing the autoignition tendency under lean MMC operation. Moreover, the fuel requirements for MMC align with that of stoichiometric operation: i.e., high RON and high S fuels are desirable for stable non-knocking operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Comparing Cetane Number Measurement Methods

Cetane number is one of the most important fuel performance metrics for mixing controlled compression-ignition “diesel” engines, quantifying a fuel’s propensity for autoignition when injected into end-of-compression-type temperature and pressure conditions. The historical default and referee method on a Cooperative Fuel Research (CFR) engine configured with indirect fuel injection and variable compression ratio is cetane number (CN) rating. A subject fuel is evaluated against primary reference fuel blends, with heptamethylnonane defining a low-reactivity endpoint of CN = 15 and hexadecane defining a high-reactivity endpoint of CN = 100. While the CN scale covers the range from zero (0) to 100, typical testing is in the range of 30 to 65 CN. Alternatively, several constant-volume combustion chamber (CVCC)-based cetane rating devices have been developed to rate fuels with an equivalent derived cetane number (DCN) or indicated cetane number (ICN). These devices measure ignition delay for fuel injected into a fixed volume of high-temperature and high-pressure air to simulate end-of-compression-type conditions. In this study, a range of novel fuel compounds are evaluated across three CVCC methods: the Ignition Quality Tester (IQT), Fuel Ignition Tester (FIT), and Advanced Fuel Ignition Delay Analyzer (AFIDA). Resulting DCNs and ICNs are compared for fuels within the normal diesel fuel range of reactivity, as well as very high (~100) and very low DCNs/ICNs (~5). Distinct differences between results from various devices are discussed. This is important to consider because some new, high-efficiency advanced compression-ignition (CI) engine combustion strategies operate with more kinetically controlled distributed combustion as opposed to mixing controlled diffusion flames. These advanced combustion strategies may benefit from new fuel chemistries, but current rating methods of CN, DCN, and ICN may not fully describe their performance. In addition, recent evidence suggests ignition delay in modern on-road diesel engines with high-pressure common rail fuel injection systems may no longer directly correlate to traditional CN fuel ratings. Simulated end-of-compression conditions are compared for CN, DCN, and ICN and discussed in the context of modern diesel engines to provide additional insight. Results highlight the potential need for revised and/or multiple fuel test conditions to measure fuel performance for advanced CI strategies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Fuel Fabrication Specification Impact Analysis for NBSR LEU Conversion

As part of a national initiative to enhance nuclear security and reduce proliferation risks, significant efforts have been undertaken by the National Nuclear Security Administration Material Management and Minimization Office of Reactor Conversion Program to convert U.S. high performance research reactors (USHPRRs) from the use of highly enriched uranium (HEU) to low-enriched uranium (LEU), including the National Bureau of Standards Reactor (NBSR). The current plan is to procure LEU fuel assemblies from commercial fabricators according to fuel specifications tailored for each USHPRR. The analysis conducted at Brookhaven National Laboratory was part of an effort to identify the sources of uncertainty in the fuel specifications that may impact the performance of the NBSR core after its conversion and, in particular, to assess the range of acceptable tolerance limits from the perspective of core safety and reactor performance. Using the stochastic neutronics code MCNP 6.2, the variations in important NBSR neutronics characteristics were analyzed as a function of the specification parameters independently and in combination. The important NBSR specification parameters analyzed were the fuel isotopic composition, the amount of impurity content in cladding, the fuel plate thickness, and the fuel element 235U mass loading. The range of variation of each specification parameter was based on the technical specification limit or available as-fabricated assay data and uncertainties. The NBSR neutronics characteristics selected for analysis were the reactor reactivity characteristics at equilibrium and the equilibrium fuel cycle length. Results show that with variations in the fabrication parameters of the as-fabricated U-10Mo fuel within the specification limitations, the excess reactivity of the NBSR LEU core remains well below the 15% Δk/k technical specification limit, and the shutdown margin is always significantly greater than the required 0.68% Δk/k. This ensures that the NBSR can be operated safely and reliably shut down for all analyzed cases within the specified fabrication limits after the LEU conversion. In the prototypic case, the fuel cycle length was 1.5 days longer than the targeted 38.5 days. In a credible worst-case scenario, where all low-reactivity parameters were combined, the fuel cycle length was reduced to 35.5 days, which is still considered manageable for reactor operations. Variations in cycle length are primarily driven by changes in 235U loading, with other parameters having secondary effects.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Incorporation of Oxygen Carrier Recycle into Large-Scale Production of Cu-Based Oxygen Carriers

One of the greatest challenges in the chemical looping combustion (CLC) of solid fuels is developing an oxygen carrier material that is reactive and attrition resistant and can be prepared at a reasonable cost. Recent efforts in oxygen carrier development have followed two primary approaches: (1) using natural ores, such as ilmenite, or (2) developing highly attrition-resistant and reactive synthetic materials. Both approaches have shortcomings, namely, the low reactivity and incompatibility of ores with solid fuel CLC and the high cost and low durability of synthetic materials. Here, a different approach is taken where attrition is assumed inevitable and the recycling of spent oxygen carrier materials is incorporated into oxygen carrier manufacture. For solid fuel CLC, Cu-based oxygen carriers are attrited and are collected with fly ash. Copper oxides are more reactive with nitric acid than most ash materials, meaning that a copper-nitrate-rich leachate can be generated. This copper nitrate stream could then be reused in oxygen carrier synthesis by impregnation. For proof of concept, leaching experiments were conducted to verify that copper oxides are selectively leached from ash-containing spent oxygen carriers. Several cases for process design are proposed based on the composition of spent materials, as the degree of copper oxidation and type of solid fuel dictate leaching residence times and general processing intensity. The four stages proposed here include impurity removal, copper leaching and recovery, solid–liquid separation, and evaporation/concentrating. The resulting process should be able to recover up to 95% of copper while minimizing inclusion of undesirable ash-based impurities.

anions↗
DOE OSTI2023

Low-Temperature Plasma Assisted Kinetics Study of Ethanol

Non-equilibrium plasma assisted kinetics of ethanol at 0.5 atm over a temperature range of 523-1203 K were studied at stoichiometric conditions by using a plasma flow reactor (PFR). The effects of plasma chemistry on fuel and its influence on neutral chemistry is decoupled with both experimental and modelling efforts. Enhanced reactivity was observed experimentally in both plasma-assisted oxidation and pyrolysis cases with fuel consumption beginning at temperatures as low as 523 K. Absolute fuel consumption was observed at temperatures nearly 200 K earlier than pure thermal reactions highlighting the effectiveness of non-equilibrium plasma to promote reactivity. Furthermore, modelling results illustrated the effect of electron impact reactions towards accelerating fuel consumption and promoting low temperature chemistry by generating excited state N2 and reactive O and OH radicals.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Kinetics of low temperature plasma assisted NH 3 /H 2 oxidation in a nanosecond-pulsed discharge

Ammonia (NH 3 ) has been widely recognized as one of the carbon-neutral fuels. However, ammonia combustion suffers low reactivity and high N 2 O/NO x emissions. Here, to overcome these issues, this work reports plasma assisted NH 3 /H 2 oxidation and unveils the kinetics of fuel oxidation and N 2 O/NO x formation by combining time-resolved laser diagnostics with plasma modeling. Firstly, we found that the NH 3 consumption is promoted with a H 2 blending ratio of 0.3, due to enhancements of H and OH formation by plasma assisted H 2 dissociation. Secondly, at a high reduced electric field, when the H 2 blending ratio increases, the NH 3 oxidation is promoted due to both the HO 2 formation and strong NO kinetic enhancement via NO-HO 2 and NO 2 -H pathways. In the meantime, it is shown that the NO mole fraction also increases with H 2 blending ratio, because the NO formation is enhanced via N( 2 D)-O 2 pathways, and the DeNO x chemistry is weakened with less NH 2 production. By contrast, at a lower reduced electric field, when the H 2 blending ratio increases, the decreased N( 2 D) formation does not produce enough NO to replenish the NO formation drop caused by lower NH 3 concentration. Thirdly, the reduced electric field non-monotonically affects fuel consumption and N 2 O/NO x formation by manipulating electron energy deposition pathways. The NH 3 consumption is maximized with an optimal reduced electric field where N 2 * excitation and O 2 dissociation are most efficient. When the reduced electric field deviates from its optimum, the NH 3 consumption decreases due to the discharge energy deposition to either vibrational excitation or dissociation of N 2 . The N 2 O/NO x emissions governed by the NH 3 oxidation follow the above NH 3 consumption trend.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Impact of gasoline composition on the effects of nitric oxide on autoignition and knock in a DISI engine

Modern spark-ignition engines use exhaust gas recirculation (EGR) to dilute the charge and suppress knock, enabling the use of higher compression ratios and/or more optimum combustion phasing for higher efficiency. The effectiveness of EGR is affected by the composition of the fuel and its chemical-kinetic interactions with combustion products. Among those, nitric oxide (NO) has been shown to strongly affect autoignition reactivity. However, the impact of fuel composition of the effect of NO on reactivity is not well-understood. Here, in this study, engine experiments were conducted to assess the impact of NO seeded to the intake on knock-limited operation of two gasoline fuels (high cycloalkane content, or HCA, and high olefin content, or HO). Results showed that compositionally-different fuels responded differently to NO. HCA, which was less knock-limited than HO for NO < 200 ppm, became more knock-limited for NO > 200 ppm. Moreover, it was found that differences in knock between fuels were caused by differences in autoignition chemistry and not in the sequential autoignition process of the end gas that occurs due to thermal stratification. Chemical kinetic simulations were performed to better understand the experimental results. For HCA, intermediate-temperature heat release had a greater impact on autoignition reactivity than low-temperature heat release, while the opposite was observed for HO. For both fuels, NO enhances the magnitude of low-temperature heat release via NO + HO 2 → NO 2 + OH. The effect of NO on reactivity was stronger for HCA because OH produced from NO helped to overcome the OH quenching effect of cyclopentane, a main species in HCA. In contrast, HO had relatively strong inherent low-temperature chemistry arising from iso-octane, which reduced the impact of NO on reactivity. For the range of NO mole fractions tested in this study, in-cylinder NO increased fuel’s knock propensity, especially for fuels with mild low-temperature chemistry.

Autoignition↗
DOE OSTI2025

An In Situ Feed Monitoring System for Molten Salt Reactors with Fast Neutron Energy Spectrum Molten Salt Reactor Applications

Molten salt reactors (MSRs) are one of the six promising advanced reactor technologies selected for further research and development by the Generation IV International Forum. More than twenty MSR designs are actively being developed around the world. Several of these designs are liquid-fueled and intended for operation within the fast neutron energy spectrum.1 National regulations will require liquid-fueled MSRs to control and account for nuclear material within licensed facilities. Additionally, states with comprehensive safeguards agreements with the International Atomic Energy Agency (IAEA) are obligated to declare nuclear material quantities within facilities. In return, the IAEA Department of Safeguards independently verifies these quantities and provides assurance that the nuclear material and facility are being used only for peaceful purposes. One key distinction of liquid-fueled MSRs compared with other types of reactors is that in portions of the facility, the nuclear material is in bulk form rather than discrete items. Traditional nuclear material accounting techniques such as physical item counting and verification of serial numbers on fresh fuel assemblies do not translate directly to all process streams within liquid-fueled reactors. Liquid-fueled MSRs are typically designed with low excess reactivity. This feature provides safety benefits but also means that most MSRs require the addition of makeup fuel salt while a reactor is operational. The nuclear material in the initial fuel salt and in any makeup fuel salt must be quantified. Additionally, distinct nuclear material diversion and reactor misuse scenarios form the basis of the detection methods and monitoring systems developed for liquid-fueled MSRs. For example, the IAEA provides assurance that fuel salt containing nuclear material is not being diverted from the system, that the feed salt matches the reported actinide concentrations and uranium enrichment, and that no additional fertile material is being introduced into the system. Measurement systems currently used for nuclear material control and accounting are not directly applicable to achieving MSR safeguards goals. This paper concerns a system being designed to account for the nuclear material added to liquid-fueled MSRs and monitor for diversion and misuse scenarios related to MSR feed systems.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Poly(oxymethylene) Ethers as a High Cetane, Low Sooting Biofuel Blendstock for Use in Medium to Heavy Duty Mixing Controlled Compression Ignition Engines

Compression ignition (CI) engines are currently the most common prime mover for medium and heavy duty vehicles; these engines contribute roughly a quarter of US greenhouse gas emissions from transportation, and even higher percentages of particulate and nitrogen oxide emissions. As a result, there have been significant efforts made to reduce these emissions, particularly through selection of low-emissions alternative fuels. Oxymethylene ethers (OMEs) are a class of molecule, typically structured R-O-(CH2O)n-R', which have been considered as a possible blendstock in CI fuels for the goal of soot reduction. Generally, past work has focused on methyl-terminated OMEs, CH3-O-(CH2O)n-CH3, which by virtue of containing no C--C bonds, produce negligible soot. These molecules show significant reductions in soot emission from engines when blended in moderate to high ratios with traditional diesels, however, they have been shown to have inferior physical properties and poor compatibility with some legacy systems. Recent theoretical work has shown that OMEs with non-methyl alkyl groups may have superior performance, albeit at the cost of increased soot formation. In this work, a variety of OMEs with terminating alkyl groups from methyl to butyl are considered for their suitability as CI fuels. The synthesis of these extended OMEs is studied, including formation of n=1 OMEs from common chemical sources, and extension of the chain length to heavier molecules, via reactions over acidic ion exchange resins. Following the synthesis, the properties of these OMEs are studied with respect to their engine applicability. It is found that heavier (propyl- and butyl-terminated) OMEs have superior properties for diesel compatibility, particularly in reactivity, volatility, and water solubility. Extended-alkyl OMEs are found to have higher soot production than methyl-terminated OMEs, but remain superior to diesel soot production on a per-unit-energy basis. A sample of a butyl-terminated OME mixture, n=2-4, is selected as the ideal OME blend for close compatibility with legacy diesel systems. This mixture is blended with certified diesel and tested for ASTM D975 compatibility, passing all required tests but lubricity; decreased heat of combustion is observed but not governed by the diesel standard. Fundamental combustion tests of various mid-weight OMEs are performed in a rapid compression machine, where it is shown that low-temperature chemistry causes a region of decreased dependence of ignition delay on temperature, consistent with methyl-terminated OME behavior. An isopropyl-terminated OME is observed to have low reactivity compared to other OMEs; this fuel is investigated via further rapid compression machine testing and CFR engine testing. It is found that this OME has strong negative-temperature-coefficient ignition behavior - a first for OMEs - and has reactivity lower than other OMEs, but insufficient for direct spark ignition engine testing.

09 BIOMASS FUELS↗
DOE OSTI2022

MODELING AND PARAMETRIC STUDY OF END-GAS AUTOIGNITION TO ALLOW THE REALIZATION OF ULTRA-LOW EMISSIONS, HIGH-EFFICIENCY HEAVY-DUTY SPARK-IGNITED NATURAL GAS ENGINES

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas (NG) engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by the low emission limits and the wide range of chemical reactivity in pipeline-quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its Methane Number (MN), which is analogous to the Octane Number for liquid SI fuels, can span from 65 to 95. In order to realize diesel-like efficiencies, SI NG engines must be designed to operate at high Brake Mean Effective Pressures (BMEP), near or beyond knock limits, over a wide range of fuel reactivity. This requires a deep understanding of the combustion-engine interactions pertaining to flame propagation and End-Gas Autoignition (EGAI), i.e., the autoignition of the unburned gas (end gas) ahead of the flame front. However, EGAI, if controlled, provides an opportunity to increase SI NG engine efficiency by increasing the combustion rate and the total fraction of burned fuel, mitigating the effects of the slow flame speeds characteristic of natural gas fuels, which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, to realize diesel-like efficiencies and ultra-low emissions on SI NG engines, this work proposes the study of the main parameters influencing the modeling and prediction of NG EGAI to allow for its control. In this work, a novel EGAI detection and onset determination method was developed to reliably quantify EGAI for data analysis and engine control. The new method allowed the prediction of EGAI on SI NG engines without the need to use engine- and operating-condition-dependent thresholds and reduced the error in quantifying the fraction of the total energy released by the EGAI event by up to 40%pts. One- and three-dimensional engine models were then developed to study the engine/fuel interactions that lead to NG EGAI and its performance benefits. These models, although having decent agreement with experimental data, showed the need to account for NOx chemistry when predicting NG EGAI due to a consistently later prediction of the EGAI onset (~1.65 crank-angle degrees) and thus, a new reduced chemical mechanism for real NG fuels was developed containing NOx chemistry. The new reduced mechanism improved the EGAI onset prediction agreement to within ±0.5 crank-angle degrees and decreased simulation time during combustion by nearly 50% when using the further reduced AREIS50NOx chemical mechanism. These models were then used to study the role of NG composition on EGAI, evaluate the engine/fuel interactions leading to NG EGAI, and perform engine optimization while leveraging EGAI to increase thermal efficiency. Piston design optimization combined with a Controlled EGAI (C-EGAI) combustion mode allowed a Heavy-Duty (HD) SI NG engine to operate at diesel-like efficiencies, i.e., Brake Thermal Efficiency (BTE) ≥44%. Experimental and modeling data analysis revealed that earlier and faster heat release increases combustion efficiency by an average of 1%pts, increases work transferred to the piston resulting in a decrease in exhaust losses by 50% depending on the engine operating condition while slightly increasing heat losses. Finally, the simulation results revealed an opportunity to further enhance the BTE (up to 50%) by enabling C-EGAI combustion at leaner conditions, λ=1.4-1.6.

Bestel, Diego Bernardi↗
DOE OSTI2023

Low-Temperature Plasma Assisted Kinetics Study of Ethanol

Abstract: Non- equilibrium plasma assisted kinetics of ethanol at 0.5 atm over a temperature range of 523-1203 K were studied at stoichiometric conditions by using a plasma flow reactor (PFR). The effects of plasma chemistry on fuel and its influence on neutral chemistry is decoupled with both experimental and modelling efforts. Enhanced reactivity was observed experimentally in both plasma-assisted oxidation and pyrolysis cases with fuel consumption beginning at temperatures as low as 523 K. Absolute fuel consumption was observed at temperatures nearly 200 K earlier than pure thermal reactions highlighting the effectiveness of non-equilibrium plasma to promote reactivity. Modelling results illustrated the effect of electron impact reactions towards accelerating fuel consumption and promoting low temperature chemistry by generating excited state N2 and reactive O and OH radicals.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Kinetics and extinction of non-premixed cool and warm flames of dimethyl ether at elevated pressure

Here, the growing demand of clean and efficient propulsion and energy systems has sparked an interest in understanding low-temperature combustion at high pressure. Cool flame transition and extinction limits as well as oxygen concentration dependence at elevated pressures provide insights of the low-temperature and high-pressure fuel reactivity. A new experimental high-pressure counterflow burner platform was designed and developed to achieve the studies of high-pressure cool flames. Dimethyl ether (DME) was chosen to study its non-premixed cool flame in high-pressure counterflow burner at pressure up to 5 atm, perhaps for the first time. This paper investigates the effects of pressure on cool flame structure, extinction and transition limits, and oxygen concentration dependence as well as ozone assisted warm flames of DME in experiments and numerical simulations. The results show that the reignition transition from cool flame to hot flame occurs either with the decrease of the strain rate at a given fuel concentration and pressure or with the increase of fuel mole fraction or pressure at a given strain rate. Furthermore, it is shown that the higher pressure shifts the cool flame to higher strain rates and results in higher cool flame extinction strain rates. However, the existing kinetic model of DME fails in predicting the cool flame extinction limit at elevated pressures. Besides, the cool flame extinction limits are proportional to nth power of the oxygen concentration, [O 2 ] n , and the increase of pressure leads to stronger extinction limit dependence (larger n) on oxygen concentration. The present experiment and detailed kinetic analysis show clearly that increasing pressure promotes the low-temperature chemistry including the oxygen addition reactions. In addition, stable warm flame was first experimentally observed by using DME at elevated pressure with ozone sensitization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emission limits and the wide range of chemical reactivity in pipeline quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its methane number (analogous to the octane number for liquid SI fuels) can span from 65 - 95. In order to realize diesel-like efficiencies, SI natural gas engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding the combustion-engine interactions pertaining to flame propagation and end-gas autoignition (EGAI). However, EGAI, if controlled, provides an opportunity to increase SI natural gas engine efficiency by increasing combustion rate and the total burned fuel, mitigating the effects of the slow flame speeds of natural gas fuels which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, in order to study EGAI phenomenon, the present work highlights multi-dimensional computational fluid dynamics (CFD) models of the Cooperative Fuel Research (CFR) engine. The CFR engine models are used to investigate fuel-engine interactions that lead to EGAI with natural gas, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). A Three-Pressure Analysis, performed with GT-Power, was used to estimate initial and boundary conditions for the three-dimensional CFD model. CONVERGE CFD v2.4 was used for the three-dimensional CFD modeling where the level set G-Equation model and SAGE detailed chemical kinetics solver were used. An assessment of the different modeling approaches is also provided to evaluate their limitations, advantages and disadvantages, and for which situations they are most applicable. Model validation was performed with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction, and IMEP and shows good agreement in Peak Cylinder Pressure (PCP), PCP crank angle, and the location of the 10%, 50%, and 90% mass fraction burned (CA10, CA50, and CA90, respectively). The models can predict the onset crank angle and pressure rise rate for light, medium, and heavy EGAI under a variety of fuel reactivities and engine operating conditions.

Bestel, Diego↗