SEARCH · Search NASA

Results for “Low temperature heat release”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Possible Sources for Methane and C2-C5 Organics in the Plume of Enceladus

In this paper we consider six possible sources of CH4 and other low-mass (C2 - C5) organics in the plume of Enceladus: initial endowments of cometary organics or Titan- like tholin, in situ production by Fisher-Tropsch type reactions, water-rock reactions, or microbiology, and thermogenesis from heavier organics already present. We report on new laboratory results C2 hydrocarbons released on thermogenesis of laboratory tholin and Fisher-Tropsch type synthesis. Tholin heating produced ratios of CH4/C2H4 and CH4/C2H6 of about 2 for temperatures up to 450 C and about 6 for a temperature of 650 C. Low pressure Fisher-Tropsch type experiments produced CH4/C2H4 of approx 1.5, similar to previous results. No C2H2 was produced by either process. Tests of gas production by four strains of methanogens confirmed the absence of any detectable production of non-methane hydrocarbons. Cometary endowment, Fisher-Tropsch type synthesis, and Titan-like tholin incorporation could be primary inputs of organics and subsequent thermal processing of any of these all are possible sources of low mass organics in the plume. Biological production and water-rock reactions are an alternative source of CH4. Neither water-- ]rock reactions or thermal processing of biomass could be a source C2 . C5 organics due to the low interior pressures. The confirmed detection of CO and C2H2 in the plume of Enceladus would provide an important constraint on sources as we have identified no process . other than the initial volatile component of cometary organics which can supply these gases. Precise determination of the relative concentrations of C1 - C5 hydrocarbons may provide additional constraints on sources but a detailed isotopic analysis of C and H in these organics and a search for amino acids constitute the next important steps in resolving the sources of the organics in Enceladus' plume.

McKay, Chris↗

NASA NTRS1993

Thermal history of comets during residence in the Oort cloud - Effect of radiogenic heating in combination with the very low thermal conductivity of amorphous ice

The thermal history of long-period comets initially composed of amorphous ice is studied. It is shown that such comets with a small nucleus thermal conductivity (kappa) experience a runaway increase in the internal temperature during residence in the Oort cloud. The temperature increase is a result of rapid release of the latent heat at crystallization triggered by gradual heating due to decay of radioactive nuclides. The time of the runaway temperature increase is about ten to a hundred million years after the formation of the nucleus depending on the fraction of refractory grains which contain radioactive nuclides. Most of the amorphous ice in the nuclides except just beneath the surface transforms into crystalline ice due to the runaway temperature increase. This implies that the ice in short-period comets is crystalline from the initial time when the long-period comet becomes a short-period one. In comets with large kappa the temperature does not rise much compared to the small kappa case and the initial amorphous ice is preserved. A criterion for the crystallization of the nucleus ice is derived.

Haruyama, Jun'ichi↗

NASA NTRS1994

A very low shock alternative to conventional, pyrotechnically operated release devices

NiTiNOL is best known for its ability to remember a preset shape, even after being 'plastically' deformed. This is accomplished by heating the material to an elevated temperature up to 120 degrees C. However, NiTiNOL has other material and mechanical properties that provide a novel method of structural release. This combination of properties allows NiTiNOL to be used as a mechanical fuse between structural components. When electrical power is applied to the NiTiNOL fuse(s), the material is annealed reducing the mechanical strength to a small fraction of the as-wrought material. The preload then fractures the weakened NiTiNOL fuse(s) and releases the structure. This paper describes the mechanical characteristics of the NiTiNOL allow used in this invention, structural separation design concepts using the NiTiNOL material, and initial test data. Elimination of the safety hazard, high shock levels, and non-reusability inherent with pyrotechnic separation devices allows NiTiNOL actuated release devices to become a viable alternative for aerospace components and systems.

Robinson, Steven P.↗

NASA NTRSDate not supplied

Asymptotic Analysis of Premixed N-alkane Cool Flame Propagation

A simplified chemical-kinetic cool-flame mechanism for n-alkanes developed recently is applied to premixed laminar cool-flame deflagrations. The present contribution derives the structure of the associated freely propagating cool premixed flame controlled by the low-temperature chemistry and develops formulas for calculating the corresponding laminar burning velocity. Application of activation-energy asymptotics reveals finite-rate chemistry without heat release occurring throughout the preheat zone and leakage of both fuel and oxygen through the thin heat-release zone, there being zones of consumption of an intermediate species on each side of the heat-release zone, thicker than that zone but still thin compared with the preheat-zone thickness. Predicted laminar burning velocities are compared with recently reported measurements for n-dodecane, performed in a newly deigned high-pressure ignition apparatus, resulting in reasonable agreement.

Cool flames↗

NASA NTRSDate not supplied

Asymptotic Analysis of Premixed N-alkane Cool Flame Propagation

cool flames↗

NASA NTRS1979

Regolith layering processes based on studies of low-temperature volatile elements in Apollo core samples

The concentrations of Hg released at at the most 130 C increase with depth in near-surface samples from cores. This is in response to a daytime thermal gradient with temperatures of approximately 400 K at the surface decreasing to approximately 250 K at greater than 10 cm depth (Keihm and Langseth, 1973). The steepness of the slopes and the depths to which the concentration gradients extend appear to be determined by the color, density and possibly the grain size of the soils. Earlier surface layers can be identified and, in general, are in agreement with other indicators of such layers. Low temperature volatilized Br exhibits trends that parallel those of Hg in a number of cases. This is also true of Br and Hg fractions released in stepwise heating experiments at higher temperatures. The coherence, especially in higher temperature fractions, between these chemically dissimilar elements implies a common physical process of entrapment; possibly one related to the presence of vapor deposits on surfaces and to opening and closing of microcracks and pores.

Jovanovic, S.↗

NASA NTRS1979

Silicon Halide-alkali Metal Flames as a Source of Solar Grade Silicon

A program is presented which was aimed at determining the feasibility of using high temperature reactions of alkali metals and silicon halides to produce low cost solar-grade silicon. Experiments are being conducted to evaluate product separation and collection processes, measure heat release parameters for scaling purposes, and determine the effects of the reactants and/or products on materials of reactor construction. During the current reporting period, the results of heat release experiments were used to design and construct a new type of thick-wall graphite reactor to produce larger quantities of silicon. A reactor test facility was constructed. Material compatibility tests were performed for Na in contact with graphite and several coated graphites. All samples were rapidly degraded at T = 1200K, while samples retained structural strength at 1700K. Pyrolytic graphite coatings cracked and separated from substances in all cases.

Olson, D. B.↗

NASA NTRSDate not supplied

Compartment Fire Modeling of a Crew Cabin in 1-g and Lunar-g

A fire inside a spacecraft poses one of the greatest dangers to the crew and mission success. As missions become more complex and longer in duration, the risk of a fire becomes more probable and catastrophic. A greater understanding of the effects of a fire inside a crewed vehicle at potential exploration atmospheres is needed. These exploration atmospheres, such as those being proposed for upcoming Lunar missions, include higher oxygen concentrations and lower pressures, also known as Normoxic conditions. Full scale fire testing, such as those performed during previous space programs, is the most straightforward way to obtain this understanding. These tests are difficult to implement in 1-g and even more challenging to attempt in Lunar-g. Modeling can help inform experiments aimed at determining flammability properties of common materials at exploration atmospheres, as well as determine the effect a fire has inside a spacecraft. A model can also be easily simulated in Lunar-g to predict the effect of gravity on fire propagation. This work focuses on a model of a theoretical partial crew cabin, with potential fire sources being a laptop and a Nomex sleeping bag. A simulation of the crew cabin during a high Heat Release Rate (HRR) fire and low HRR fire at 1-g was compared to simulations at Lunar-g. It was found that in both the low and high HRR cases, the temperature in the cabin was higher in the Lunar-g case than in the 1-g case. This is likely due to the hot products moving out the door of the crew cabin faster in the 1-g case. Modeling case studies like these will help guide future full-scale flammability experiments on Earth and allow for the prediction of fire spread in a Lunar gravity environment in order to design a safer crew cabin.

Fire Safety↗

NASA NTRS1988

Microgravity combustion discipline working group summary of requirements for noncontact temperature measurements

Current efforts of the Microgravity Combustion Working Group are summarized and the temperature measurement requirements for the combustion studies are defined. Many of the combustion systems that are studied in the low gravity environment are near-limit systems, that is, systems that are acting near the limit of flammability in terms of oxygen concentration or fuel concentration. Systems of this type are normally weak in the sense that there is a delicate balance between the heat released in the flame and the heat required to sustain the flame. Intrusive or perturbative temperature measurement probes can be inaccurate in these situations and in the limiting case extinguish the flame. Noncontact techniques then become the only way to obtain the required measurements. Noncontact measurement requirements for each of the three thermodynamic phases are described in terms of spatial and temporal resolution and temperature range.

Sacksteder, Kurt↗

NASA NTRS1980

Development of processes for the production of solar grade silicon from halides and alkali metals

High temperature reactions of silicon halides with alkali metals for the production of solar grade silicon in volume at low cost were studied. Experiments were performed to evaluate product separation and collection processes, measure heat release parameters for scaling purposes, determine the effects of reactants and/or products on materials of reactor construction, and make preliminary engineering and economic analyses of a scaled-up process.

Dickson, C. R.↗

NASA NTRS1996

Dynamics of the Impacts

The SL9 impacts are best known by their plumes, several of which were imaged towering 3000 km above Jupiter's limb. The heat released when they fen back on the atmosphere produced the famous infrared main events. The reentry shock was observed directly in CO emission and indirectly through thermally glowing dust. The relatively low color temperature of the latter implies that most of the energy released on reentry was radiated. If so, the R impact released some 3 x 10(exp 26) ergs, and the larger L, K, and G impacts as much as 3 x 10(exp 27) ergs. These estimates agree well with impact energies deduced from tidal disruption computations. The duration of the infrared events measures time aloft and hence provides a second measure of plume height. These indicate that plume height was only weakly dependent on impact energy. Evidently all the plumes were launched at roughly 10-13 km/s. Using a semi-analytic model for the deceleration, disintegration, and destruction of intruding bodies by an ever-vigilant atmosphere, we find that similar plume heights is a direct consequence of smaller impactors exploding at higher altitudes, in such a way that the different explosions were geometrically similar. We then compare the predictions of our model to the Venerian cratering record, which provides a good statistical test of impact deceleration by a thick atmosphere. Chemistry should have provided an independent measure of explosion altitude: abundant shock-generated CS, CS2 and HCN indicates a source in dry jovian air, above the putative water clouds. However, the Galileo Probe results seem to imply that we should expect no more. Observed water and S2 are consistent with a somewhat oxidized gas (presumably the comet itself), but the absence of SO2 and CO2 shows that conditions were neither too oxidizing nor the shocks too hot.

Zahnle, Kevin↗

NASA NTRS2017

Passive Gas-Gap Heat Switches for Use in Low-Temperature Cryogenic Systems

We present the current state of development in passive gas-gap heat switches. This type of switch does not require a separate heater to activate heat transfer but, instead, relies upon the warming of one end due to an intrinsic step in a thermodynamic cycle to raise a getter above a threshold temperature. Above this temperature sequestered gas is released to couple both sides of the switch. This enhances the thermodynamic efficiency of the system and reduces the complexity of the control system. Various gas mixtures and getter configurations will be presented.

Heat Switches↗

NASA NTRS1982

Thermochemical generation of hydrogen

The direct fluid contact heat exchange with H2SO4 at about 330 C prior to high temperature decomposition at about 830 C in the oxygen release step of several thermochemical cycles for splitting water into hydrogen and oxygen provides higher heat transfer rates, savings in energy and permits use of cast vessels rather than expensive forged alloy indirect heat exchangers. Among several candidate perfluorocarbon liquids tested, only perfluoropropylene oxide polymers having a degree of polymerization from about 10 to 60 were chemically stable, had low miscibility and vapor pressure when tested with sulfuric acid at temperatures from 300 C to 400 C.

Lawson, D. D.↗

NASA NTRS2007

Radiative Extinction of Gaseous Spherical Diffusion Flames in Microgravity

Radiative extinction of spherical diffusion flames was investigated experimentally and numerically. The experiments involved microgravity spherical diffusion flames burning ethylene and propane at 0.98 bar. Both normal (fuel flowing into oxidizer) and inverse (oxidizer flowing into fuel) flames were studied, with nitrogen supplied to either the fuel or the oxygen. Flame conditions were chosen to ensure that the flames extinguished within the 2.2 s of available test time; thus extinction occurred during unsteady flame conditions. Diagnostics included color video and thin-filament pyrometry. The computations, which simulated flow from a porous sphere into a quiescent environment, included detailed chemistry, transport and radiation, and yielded transient results. Radiative extinction was observed experimentally and simulated numerically. Extinction time, peak temperature, and radiative loss fraction were found to be independent of flow rate except at very low flow rates. Radiative heat loss was dominated by the combustion products downstream of the flame and was found to scale with flame surface area, not volume. For large transient flames the heat release rate also scaled with surface area and thus the radiative loss fraction was largely independent of flow rate. Peak temperatures at extinction onset were about 1100 K, which is significantly lower than for kinetic extinction. One observation of this work is that while radiative heat losses can drive transient extinction, this is not because radiative losses are increasing with time (flame size) but rather because the heat release rate is falling off as the temperature drops.

Santa, K. J.↗

NASA NTRS2013

Hydrogen-Enhanced Lunar Oxygen Extraction and Storage Using Only Solar Power

The innovation consists of a thermodynamic system for extracting in situ oxygen vapor from lunar regolith using a solar photovoltaic power source in a reactor, a method for thermally insulating the reactor, a method for protecting the reactor internal components from oxidation by the extracted oxygen, a method for removing unwanted chemical species produced in the reactor from the oxygen vapor, a method for passively storing the oxygen, and a method for releasing high-purity oxygen from storage for lunar use. Lunar oxygen exists in various types of minerals, mostly silicates. The energy required to extract the oxygen from the minerals is 30 to 60 MJ/kg O. Using simple heating, the extraction rate depends on temperature. The minimum temperature is approximately 2,500 K, which is at the upper end of available oven temperatures. The oxygen is released from storage in a purified state, as needed, especially if for human consumption. This method extracts oxygen from regolith by treating the problem as a closed batch cycle system. The innovation works equally well in Earth or Lunar gravity fields, at low partial pressure of oxygen, and makes use of in situ regolith for system insulation. The innovation extracts oxygen from lunar regolith using a method similar to vacuum pyrolysis, but with hydrogen cover gas added stoichiometrically to react with the oxygen as it is produced by radiatively heating regolith to 2,500 K. The hydrogen flows over and through the heating element (HE), protecting it from released oxygen. The H2 O2 heat of reaction is regeneratively recovered to assist the heating process. Lunar regolith is loaded into a large-diameter, low-height pancake reactor powered by photovoltaic cells. The reactor lid contains a 2,500 K HE that radiates downward onto the regolith to heat it and extract oxygen, and is shielded above by a multi-layer tungsten radiation shield. Hydrogen cover gas percolates through the perforated tungsten shielding and HE, preventing oxidation of the shielding and HE, and reacting with the oxygen to form water vapor. The water vapor is filtered through solid regolith to remove unwanted extraction byproducts, and then condensed to a liquid state and stored at 300 to 325 K. Conversion to usable oxygen is achieved by pumping liquid water into a high-pressure electrolyzer, storing the gaseous oxygen at high pressure for use, and diverting the hydrogen back to the reactor or to storage. The results from this design effort show that this oxygen-generating concept can be developed in an efficient system with low specific mass. Advantages include use of regolith as an oxygen source, filter, and thermal insulator. The system can be tested in Earth gravity and can be expected to operate similarly in lunar gravity. The system is scalable, either by increasing the power level and output of a standard module, or by employing multiple modules.

Burton, rodney↗

NASA NTRS2014

Current Ground Test Options for Nuclear Thermal Propulsion (NTP)

About 20 different NTP engines/ reactors were tested from 1959 to 1972 as part of the Rover and Nuclear Engine for Rocket Vehicle Application (NERVA) program. Most were tested in open air at test cell A or test cell C, at the Nevada Test Site (NTS). Even after serious engine breakdowns of the reactor (e.g., Phoebus 1A), the test cells were cleaned up for other engine tests. The engine test stand (ETS) was made for high altitude (approximately 1 psia) testing of an NTP engine with a flight configuration, but still had the exhaust released to open air. The Rover/NERVA program became aware of new environmental regulations which would prohibit the release of any significant quantity of radioactive particulates and noble gases into the open air. The nuclear furnace (NF-1) was the last reactor tested before the program was cancelled in 1973, but successfully demonstrated a scrubber concept on how to filter the NTP exhaust. The NF-1 was demonstrated in the summer of 1972. The NF-1 used a 44MW reactor and operated each run for approximately 90 minutes. The system cooled the hot hydrogen exhaust from the engine with a water spray before entering a particle filter. The exhaust then passed through a series of heat exchangers and water separators to help remove water from the exhaust and further reduce the exhaust temperatures. The exhaust was next prepared for the charcoal trap by passing through a dryer and effluent cooler to bring exhaust temperatures close to liquid nitrogen. At those low temperatures, most of the noble gases (e.g., Xe and Kr made from fission products) get captured in the charcoal trap. The filtered hydrogen is finally passed through a flare stack and released to the air. The concept was overall successful but did show a La plating on some surfaces and had multiple recommendations for improvement. The most recent detailed study on the NTP scrubber concept was performed by the ARES Corporation in 2006. The concept is based on a 50,000 lbf thrust engine (approximately 1 GW) with a maximum burn time of 1 hour. The concept utilized lessons learned from NF-1. The strategy breaks down the exhaust into parallel paths to allow flexibility with engine size and mass flow of exhaust. Similar to NF-1, the exhaust is slowed down, cooled, filtered of particulates, filtered of noble gases, and then the clean hydrogen is flared to open air. Another concept proposed by Steve Howe (currently Director of the Center for Space Nuclear Research) to simplify the NTP exhaust filtering is to run the hydrogen exhaust into boreholes underground to filter the exhaust. The two borehole site locations proposed are at the NTS and at the Idaho National Laboratory (INL). At NTS, the boreholes are 8' diameter and 1200' deep. The permeability of hydrogen through the soil and its buoyancy will allow it to rise up through the soil and allow the filtering of noble gases and radioactive particulates. The exhaust needs to be cooled to 600C before entering the borehole to avoid soil glazing. Preliminary analysis shows a small buildup of back pressure with time which depends on permeability. Noble gases entering the borehole walls deep can take a long time before reaching the surface. Other factors affecting permeability include borehole pressure, water saturation, and turbulence. Also, a possible need to pump out contaminated water collected at the bottom of the borehole. At INL, the borehole concept is slightly different. The underground borehole has openings to the soil at special depths which have impermeable interbeds above the water table and below the surface to allow the exhaust to travel horizontal between the impermeable layers. Preliminary results indicate better permeability than at NTS. The last option is total containment of the exhaust during the test run. The concept involves slowing down the flow to subsonic in a water cooled diffuser. The hydrogen is burned off in an oxygen rich afterburner with the only products being steam, oxygen, and some noble gases. A heat exchanger and water spray pulls heat from the steam and lowers the temperature for condensation. The optimum ratio between the two is being investigated, with a goal to minimize the total volume of the water hold tanks. A water tank farm collects the contaminated water. The amount of water produced from burning the hydrogen is approximately 100,000 gallons (not including cooling water) for a 25k lbf engine operating for 50 minutes. Residual gases (e.g., oxygen and some noble gases) can be captured at cryogenic levels with a liquid nitrogen cooled dewar. After a few weeks post-test, the radiation levels can drop to more favorable levels before slowly draining each capture tank and using existing filters. With today's environmental regulations, the NTP exhaust is filtered to meet 10 mrem/year exposure to the general public (at a DOE site) or 100 mrem/year (via NRC when tested elsewhere), when natural background radiation exposure to the general public is 300- 600 mrem per year. The current society feels more comfortable with filtering even lower to as low as reasonably achievable (ALARA).

Gerrish, Harold P., Jr.↗

NASA NTRS1992

Solar-type xenon - Isotopic abundances in Pesyanoe

Elemental and isotopic abundances of Ar and Xe were measured in three grain-size separates in the dark phase of the enstatite achondrite Pesyanoe by stepwise heating, using a combination of pyrolysis and combustion steps. The data reveal a low-temperature gas fraction with Ar/Xe ratios close to the solar ratio and isotopically similar to solar-type Ar and Xe observed in lunar samples. The gas released at intermediate temperature steps shows that Ar and Xe are isotopically fractionated, compared to the low-temperature components. Pesyanoe does not have excess Ar-40 and fission Xe, which means its parent body was too small for ion reimplantation. It is concluded that solar-type Xe isotopic abundances can be inferred from the low-temperature component. A comparison of Pesyanoe and lunar data shows that isotopic signatures of solar-wind Xe, as sampled at two different points in solar system space and time, are identical within experimental error.

Kim, J. S.↗

NASA NTRS1995

Animal biocalorimeter and waste management system

A biocalorimeter and waste management system is provided for making metabolic heat release measurements of animals or humans in a calorimeter (enclosure) using ambient air as a low velocity source of ventilating air through the enclosure. A shroud forces ventilating air to pass over the enclosure from an end open to ambient air at the end of the enclosure opposite its ventilating air inlet end and closed around the inlet end of the enclosure in order to obviate the need for regulating ambient air temperature. Psychrometers for measuring dry- and wet-bulb temperature of ventilating air make it possible to account for the sensible and latent heat additions to the ventilating air. A waste removal system momentarily recirculates high velocity air in a closed circuit through the calorimeter wherein a sudden rise in moisture is detected in the ventilating air from the outlet.

Poppendiek, Heinz F.↗