Search NASA⌕ Search

SEARCH · Search NASA

Results for “MISSILE CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

A ram-air-spoiler roll stabilization device for forward control cruciform missiles

An experimental investigation has been made at supersonic Mach numbers to determine the feasibility of using a ram-air-spoiler roll control device on a typical canard control missile configuration. As a basis for roll control comparisons, conventional aileron controls on the tail fins were also tested. Results are presented which indicate that the addition of nacelles on the missile tail fins resulted in satisfactory roll control effectiveness and only small changes in basic missile stability. The ram-air-spoiler roll control effectiveness is relatively constant over the range of vehicle attitudes and Mach numbers investigated.

Blair, A. B., Jr.↗
NASA NTRS1985

Wind-tunnel investigation at supersonic speeds of a remote-controlled canard missile with a free-rolling-tail brake torque system

Wind tunnel tests were conducted at Mach numbers 1.70, 2.16, and 2.86 to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed or free rolling tailfin afterbodies. Mechanical coupling effects of the free-rolling-tail afterbody were investigated by using an electronic electromagnetic brake system providing arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail roll rate. Remote-controlled canards were deflected to provide pitch, yaw, and roll control. Results indicate that the induced rolling moment coefficients due to canard yaw control are reduced and linearized for the free-rolling-tail (free-tail) configuration. The canards of the latter provide conventional roll control for the entire angle-of-attack test range. For the free-tail configuration, the induced rolling moment coefficient due to canard yaw control increased and the canard roll control decreased with increases in brake torque, which simulated bearing friction torque. It appears that a compromise in regard to bearing friction, for example, low-cost bearings with some friction, may allow satisfactory free-tail aerodynamic characteristics that include reductions in adverse rolling-moment coefficients and lower tail roll rates.

Blair, A. B., Jr.↗
NASA NTRS1981

Remote control canard missile with a free-rolling tail brake torque system

An experimental wind-tunnel investigation has been conducted at supersonic Mach numbers to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed and free-rolling tail-fin afterbodies. Mechanical coupling effects of the free-rolling tail afterbody were investigated using an electronic/electromagnetic brake system that provides arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail-roll rate. Results are summarized to show the effects of fixed and free-rolling tail-fin afterbodies that include simulated measured bearing friction torques on the longitudinal and lateral-directional aerodynamic characteristics.

Blair, A. B., Jr.↗
NASA NTRS1959

Analytical Investigation of a Flicker-Type Roll Control for a Mach Number 6 Missile with Aerodynamic Controls Over An Altitude Range of 82,000 to 282,000 feet

An analytical investigation has been carried out to determine the responses of a flicker-type roll control incorporated in a missile which traverses a range of Mach number of 6.3 at an altitude of 82,000 feet to 5.26 at an altitude of 282,000 feet. The missile has 80 deg delta wings in a cruciform arrangement with aerodynamic controls attached to the fuselage near the wing trailing edge and indexed 450 to the wings. Most of the investigation was carried out on an analog computer. Results showed that roll stabilization that may be adequate for many cases can be obtained over the altitude range considered, providing that the rate factor can be changed with altitude. The response would be improved if the control deflection were made larger at the higher altitudes. lag times less than 0.04 second improve the response appreciably. Asymmetries that produce steady rolling moments can be very detrimental to the response in some cases. The wing damping made a negligible contribution to the response.

Lundstrom, Reginald R.↗
NASA NTRS1979

Aerodynamic characteristics of missile configurations based on Soviet design concepts

The aerodynamic characteristics of several missile concepts are examined. The configurations, which are based on some typical Soviet design concepts, include fixed-wing missiles with either forward- or aft-tail controls, and wing-control missiles with fixed aft stabilizing surfaces. The conceptual missions include air-to-air, surface-to-air, air-to-surface, and surface-to-surface. Analytical and experimental results indicate that through the proper shaping and location of components, and through the exploitation of local flow fields, the concepts provide generally good stability characteristics, high control effectiveness, and low control hinge moments. In addition, in the case of some cruise-type missions, there are indications of the application of area ruling as a means of improving the aerodynamic efficiency. In general, a point-design philosophy is indicated whereby a particular configuration is developed for performing a particular mission.

Spearman, M. L.↗
NASA NTRS1984

Missile rolling tail brake torque system

Apparatus for simulating varying levels of friction in the bearings of a free rolling tail afterbody on a canard-controlled missile to determine friction effects on aerodynamic control characteristics is described. A ring located between the missile body and the afterbody is utilized in a servo system to create varying levels of friction between the missile body and the afterbody to simulate bearing friction.

Davis, W. T.↗
NASA NTRS1961

Aerodynamic Characteristics in Pitch of a Series of Cruciform-Wing Missiles with Canard Controls at a Mach Number of 2.01

An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01 to determine the static longitudinal stability and control characteristics of a series of missile configurations with canard controls at angles of attack up to about 28 deg. The missiles had cruciform wings and canard surfaces of delta plan form with 70 deg.swept leading edges. Five bodies having fineness ratios of 19.1, 17.7, 16.7, 15.7, and 14.8 were investigated. The results of the investigation indicated a large nonlinear variation of pitching moment with angle of attack for the body of largest fineness ratio that was progressively reduced by decreasing the fineness ratio until it was essentially eliminated for a body of fineness ratio 14.8. The increased linearity of the moment curve would make it possible to reduce the margin of stability so that, for a given canard size and deflection, a higher trim angle of attack might be obtained for the shortest missile than for the longest missile. The pitching-moment results indicated that methods of prediction which assumed linear variations with angle of attack for the wing-alone and wing-plus-interference characteristics were adequate for angles of attack up to about 12 deg. At higher angles of attack it was evident that the characteristics of these components were nonlinear and that more refined methods would be required for adequate prediction.

Spearman, M. Leroy↗
NASA NTRS1988

Technology transfer: Imaging tracker to robotic controller

The transformation of an imaging tracker to a robotic controller is described. A multimode tracker was developed for fire and forget missile systems. The tracker locks on to target images within an acquisition window using multiple image tracking algorithms to provide guidance commands to missile control systems. This basic tracker technology is used with the addition of a ranging algorithm based on sizing a cooperative target to perform autonomous guidance and control of a platform for an Advanced Development Project on automation and robotics. A ranging tracker is required to provide the positioning necessary for robotic control. A simple functional demonstration of the feasibility of this approach was performed and described. More realistic demonstrations are under way at NASA-JSC. In particular, this modified tracker, or robotic controller, will be used to autonomously guide the Man Maneuvering Unit (MMU) to targets such as disabled astronauts or tools as part of the EVA Retriever efforts. It will also be used to control the orbiter's Remote Manipulator Systems (RMS) in autonomous approach and positioning demonstrations. These efforts will also be discussed.

Otaguro, M. S.↗
NASA NTRS1984

Aerodynamic characteristics of a Sparrow 3 missile model in the flow field of a generalized parent body at Mach 2.86

Longitudinal aerodynamic characteristics of a Sparrow 3 wing control missile model were measured through a range of separation distances relative to a flat plate surface that represented the parent-body configuration. Measurements were obtained with and without two dimensional circular arc protuberances attached to the flat plate surface. The tests were conducted at a Mach number of 2.86 and a Reynolds number per meter of 6.56 million. The behavior of these longitudinal characteristics with varying separation distance in the flow field created by the flat plate and protuberance was generally as would be expected on the basis of flow field boundaries determined from the second order approximation of Friedrich. In general, varying roll angle from 0 deg to 45 deg caused no significant effect on the store separation characteristics.

Stallings, R. L., Jr.↗
NASA NTRS1979

Vortex development on slender missiles at supersonic speeds

A theoretical and experimental effort has been made to develop a vortex-prediction capability on circular and noncircular missiles at supersonic speeds. Predicted vortex patterns are computed by two linear-theory computer codes. One calculates the strengths and initial locations of the vortices, and the other calculates their trajectories. A short color motion picture has been produced from the calculations to illustrate the predicted vortex patterns on a typical missile. Experimental vapor-screen photographs are presented to show the longitudinal development of the vortices on a fin-control missile. Comparisons are made between these data and the predicted vortices to assess the accuracy of the theory. The theory appears to be fairly accurate in predicting the number, locations, and relative strengths of individual vortices which develop over the missile, but cannot predict vortex sheets or diffuse vorticity whenever they occur.

Allen, J. M.↗
NASA NTRS1988

Optimization of slender wings for center-of-pressure shift due to change in Mach number

It is observed that the center of pressure on a wing shifts as the Mach number is changed. Such shifts are in general undesirable and are sometimes compensated for by actively shifting the center of gravity of the aircraft or by using active stability controls. To avoid this complication, it is desirable to design the wings of a high speed aircraft so as to minimize the extent of the center-of-pressure shifts. This, together with a desire to minimize the center-of-pressure shifts in missile control surfaces, provides the motivation for this project. There are many design parameters which affect center-of-pressure shifts, but it is expected that the largest effects are due to the wing planform. Thus, for the sake of simplicity, this study is confined to an investigation of thin, flat, (i.e., no camber or twist), relatively slender, pointed wings flying at a small angle of attack. Once the dependence of the center of pressure on planform and Mach number is understood, we can expect to investigate the sensitivity of the center-of-pressure shifts to various other parameters.

Andersen, Carl M.↗