Search NASA⌕ Search

SEARCH · Search NASA

Results for “MMC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Development of pore-free Ti-Al-C MAX/Al-Si MMC composite materials manufactured by squeeze casting infiltration

Highlights: • Open-porous MAX phase preforms were synthesized by Microwave Assisted Self-propagating High-temperature Synthesis • Manufactured preforms were infiltrated by Al-Si alloy with the use of Squeeze Casting method to create pore-free composites • Obtained materials were characterized by the means of SEM, TEM and XRD analyses • Mechanical properties were tested and discussed in relation to the microstructures An innovative method of manufacturing of Ti-Al-C MAX/Al-Si MMC composite materials was developed using squeeze casting infiltration of open-porous MAX phase preforms. Self-propagating High-temperature Synthesis (SHS) in microwave-assisted mode was applied for the creation of preforms in the Ti-Al-C system, that were subsequently infiltrated with Al-Si alloy to create dense composite materials. Microstructure and phase composition, structural defects and potential impacts between constituents of manufactured composites were characterized by the means of SEM and TEM microscopies and XRD analysis. No undesired reaction at the interface was observed, but TiC inclusions were identified in the material. Among the mechanical properties, the instrumental Young's modulus and Vickers hardness were established. The hardness and the elastic modulus of the matrix were enhanced 4 to 5 times. Wear behaviour was tested with a “pin-on-flat” method with the reciprocating motion for different load values (0.1, 0.2 and 0.5 MPa) for tool steel counterpart. Wear resistance of the composite material (WR = 1.6–2.3 × 10{sup −4} mm{sup 3}/Nm) was twofold higher than for the sole matrix (WR = 3.5–4.8 × 10{sup −4} mm{sup 3}/Nm). The developed manufacturing method allows the effective fabrication of pore-free MAX phase based MMC composite materials, with significantly higher wear resistance than the widely applied Al-Si alloys.

36 MATERIALS SCIENCE↗

Control of MMC-HVDC in low-inertia weak grids

With the inherent benefits of high-voltage direct current (HVDC) transmission systems like long-distance high-power transmission with lesser losses and costs, easy integration of renewables, and others, increased presence of DC-AC grids is expected. One of the consequences of increased presence of power electronics is the reduced inertia in the grid, which is an emerging concern. Moreover, the long length of AC transmission lines result in the presence of weak grids (with low short-circuit ratio). To address these concerns, an advanced control algorithm is proposed to control the modular multilevel converter (MMC) based HVDC substation that is connected to a low-inertia weak-grid. The algorithm is based on optimization of control states like frequency, capacitor voltages, active power, and currents in the MMC. The performance of the proposed algorithm is validated in PSCAD/EMTDC to show the effectiveness of the proposed strategy.

Debnath, Suman↗

Magnetic Microcalorimeter (MMC) Gamma Detectors with Ultra-High Energy Resolution

The goal of this LCP is to develop ultra-high resolution gamma detectors based on magnetic microcalorimeters (MMCs) for accurate non-destructive analysis (NDA) of nuclear materials. For highest energy resolution, we will introduce erbium-doped silver (Ag:Er) as a novel sensor material, and implement several geometry and design changes to improve the signal-to-noise ratio. The detector sensitivity will be increased by developing arrays of 32 Ag:Er pixels read out by 16 SQUID preamplifiers, and by developing a cryogenic Compton veto to reduce the spectral background. Since best MMC performance requires detector operation at ~10 mK, we will purchase a dilution refrigerator with a base temperature <10 mK and adapt it for MMC operation. The detector performance will be tested with radioactive sources of interest to the safeguards community.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NDE of titanium alloy MMC rings for gas turbine engines

Progress in the processing and fabrication of metal matrix composites (MMC's) requires appropriate mechanical and nondestructive testing methods. These methods are needed to characterize properties, assess integrity, and predict the life of engine components such as compressor rotors, blades, and vanes. Capabilities and limitations of several state-of-the-art nondestructive evaluation (NDE) technologies are investigated for characterizing titanium MMC rings for gas turbine engines. The use of NDE technologies such as x-ray computed tomography, radiography, and ultrasonics in identifying fabrication-related problems that caused defects in components is examined. Acousto-ultrasonics was explored to assess degradation of material mechanical properties by using stress wave factor and ultrasonic velocity measurements before and after the burst testing of the rings.

Baaklini, George Y.↗

Cost Models for MMC Manufacturing Processes

The quality cost modeling (QCM) tool is intended to be a relatively simple-to-use device for obtaining a first-order assessment of the quality-cost relationship for a given process-material combination. The QCM curve is a plot of cost versus quality (an index indicating microstructural quality), which is unique for a given process-material combination. The QCM curve indicates the tradeoff between cost and performance, thus enabling one to evaluate affordability. Additionally, the effect of changes in process design, raw materials, and process conditions on the cost-quality relationship can be evaluated. Such results might indicate the most efficient means to obtain improved quality at reduced cost by process design refinements, the implementation of sensors and models for closed loop process control, or improvement in the properties of raw materials being fed into the process. QCM also allows alternative processes for producing the same or similar material to be compared in terms of their potential for producing competitively priced, high quality material. Aside from demonstrating the usefulness of the QCM concept, this is one of the main foci of the present research program, namely to compare processes for making continuous fiber reinforced, metal matrix composites (MMC's). Two processes, low pressure plasma spray deposition and tape casting are considered for QCM development. This document consists of a detailed look at the design of the QCM approach, followed by discussion of the application of QCM to each of the selected MMC manufacturing processes along with results, comparison of processes, and finally, a summary of findings and recommendations.

Elzey, Dana M.↗

Hardware Design of a 1.7 kV SiC MOSFET Based MMC for Medium Voltage Motor Drives

Abstract—This paper presents the hardware design of a 7 kV dc bus,1 MVA, 0-1,000 Hz, 1.7 kV SiC MOSFET based medium voltage variable speed drive (MVVSD)1. The system is based on a 7-level three-phase modular multilevel converter (MMC). The full in-depth design, development, and testing of this prototype are provided, including MMC submodule development, arm inductor design, control hardware realization, system integration and thermal analysis. Finally, experimental results demonstrate the excellent performance of the 1.7 kV SiC MOSFET based submodule and the 1 MW, 7 kV MVVSD as a unity in various operation modes

SiC MOSFET, Modular Multilevel Converter, Medium V↗

The correlation of local deformation and stress-assisted local phase transformations in MMC foams

Cellular structures are of growing interest for industry, and are of particular importance for lightweight applications. In this paper, a special case of metal matrix composite foams (MMCs) is investigated. The investigated foams are composed of austenitic steel exhibiting transformation induced plasticity (TRIP) and magnesia partially stabilized zirconia (Mg-PSZ). Both components exhibit martensitic phase transformation during deformation, thus generating the potential for improved mechanical properties such as strength, ductility, and energy absorption capability. The aim of these investigations was to show that stress-assisted phase transformations within the ceramic reinforcement correspond to strong local deformation, and to determine whether they can trigger martensitic phase transformations in the steel matrix. To this end, in situ interrupted compression experiments were performed in an X-ray computed tomography device (XCT). By using a recently developed registration algorithm, local deformation could be calculated and regions of interest could be defined. Corresponding cross sections were prepared and used to analyze the local phase composition by electron backscatter diffraction (EBSD). The results show a strong correlation between local deformation and phase transformation. - Graphical abstract: Display Omitted - Highlights: • In situ compressive deformation on MMC foams was performed in an XCT. • Local deformation fields and their gradient amplitudes were estimated. • Cross sections were manufactured containing defined regions of interest. • Local EBSD phase analysis was performed. • Local deformation and local phase transformation are correlated.

36 MATERIALS SCIENCE↗

Parallel-in-Time Simulation Algorithm for Power Electronics: MMC-HVdc System

The complexity in simulating power electronics like modular multilevel converters (MMCs) requires simulation algorithms to speed-up the process. Existing simulation algorithms exploit spatial parallelism to speed-up simulation. With rise in complexity of power electronics and presence of increased number of states within them, there are limits in the speed-up using spatial parallelism. In this paper, a temporal parallelism algorithm based on parallel-in-time methods is developed for simulation of power-electronics-systems. The temporal parallelism algorithm is based on computation of power-electronics-states on coarse and fine time-steps using different models. The models of power-electronics-systems used in coarse and fine time-steps are average-value and detailed models, respectively. The updates to states on coarse time-step are computed serially and are used to initialize the states on fine time-step. The updates on fine time-step are computed in parallel. A translation method is proposed in this paper to update the states on fine time-step from the simulations in the coarse time-step, and vice-versa. The proposed algorithm is applied to simulate MMCs and is validated with respect to a detailed reference MMC model. The proposed algorithm recorded a speed-up of up to 3.47× with 5 cores.

42 ENGINEERING↗

Fundamental-Frequency Reactive Circulating Current Injection for Capacitor Voltage Balancing in Hybrid-MMC HVDC Systems During Riding Through PTG Faults

Here, this article presents a comprehensive analysis and a novel solution for the discharge problem on the half-bridge submodules' (HBSMs') capacitors in the hybrid modular multilevel converter (MMC)-based high-voltage direct current transmission systems under a long-term (e.g., several minutes or longer) pole-to-ground fault condition. The mechanism of this issue is analyzed, and then a solution based on fundamental-frequency reactive circulating current (FFRCC) injection is proposed. The influence of FFRCC injection is analyzed in terms of the fluctuated arm capacitor energy and the current stress of semiconductors. Moreover, an enhanced arm voltage modulation method based on HBSMs and full-bridge submodules coordinate control is proposed to accelerate the capacitor voltage balance of HBSMs. Finally, the performance of the proposed control strategy is verified by the simulation results.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Marble MMC v1.0

Software toolchain to program the MMC on Marble boards

Doolittle, LawrenceR↗

Development of Elevated Temperature Aluminum Metal Matrix Composite (MMC) Alloy and Its Processing Technology

The objective of this project was to provide a production capable cast aluminum metal matrix composite (MMC) alloy with an operating temperature capability of 250-300°C. Important industrial sectors as well as the military now seek lightweight aluminum alloy castings that can operate in temperature ranges of 250-300°C. Current needs in this temperature range are being satisfied by the use of titanium alloy castings. These have the desired strength properties but the end components are heavier and significantly more costly. Also, the energy requirements for production of titanium alloy castings are significantly higher than those required for production of aluminum alloys and aluminum alloy castings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Liquid oxygen LOX compatibility evaluations of aluminum lithium (Al-Li) alloys: Investigation of the Alcoa 2090 and MMC weldalite 049 alloys

The behavior of liquid oxygen (LOX) compatibility of aluminum lithium (Al-Li) alloys is investigated. Alloy systems of Alcoa 2090, vintages 1 to 3, and of Martin Marietta Corporation (MMC) Weldalite 049 were evaluated for their behavior related to the LOX compatibility employing liquid oxygen impact test conditions under ambient pressures and up to 1000 psi. The developments of these aluminum lithium alloys are of critical and significant interest because of their lower densities and higher specific strengths and improved mechanical properties at cryogenic temperatures. Of the different LOX impact tests carried out at the Marshall Space Flight Center (MSFC), it is seen that in certain test conditions at higher pressures, not all Al-Li alloys are LOX compatible. In case of any reactivity, it appears that lithium makes the material more sensitive at grain boundaries due to microstructural inhomogeneities and associated precipitate free zones (PFZ). The objectives were to identify and rationalize the microstructural mechanisms that could be relaxed to LOX compatibility behavior of the alloy system in consideration. The LOX compatibility behavior of Al-Li 2090 and Weldalite 049 is analyzed in detail using microstructural characterization techniques with light optical metallography, scanning electron microscopy (SEM), electron microprobe analysis, and surface studies using secondary ion mass spectrometry (SIMS), electron spectroscopy in chemical analysis (ESCA) and Auger electron spectroscopy (AES). Differences in the behavior of these aluminum lithium alloys are assessed and related to their chemistry, heat treatment conditions, and microstructural effects.

Diwan, Ravinder M.↗

Inelastic deformation mechanisms in SCS-6/Ti 15-3 MMC lamina under compression

An investigation was undertaken to study the inelastic deformation mechanisms in (0)(sub 8) and (90)(sub 8) Ti 15-3/SCS-6 lamina subjected to pure compression. Monotonic tests were conducted at room temperature (RT), 538 C and 650 C. Results indicate that mechanical response and deformation characteristics were different in monotonic tension and compression loading whereas some of those differences could be attributed to residual stress effects. There were other differences because of changes in damage and failure modes. The inelastic deformation in the (0)(sub 8) lamina under compression was controlled primarily by matrix plasticity, although some evidence of fiber-matrix debonding was observed. Failure of the specimen in compression was due to fiber buckling in a macroscopic shear zone (the failure plane). The inelastic deformation mechanisms under compression in (90)(sub 8) lamina were controlled by radial fiber fracture, matrix plasticity, and fiber-matrix debonding. The radial fiber fracture was a new damage mode observed for MMC's. Constitutive response was predicted for both the (0)(sub 8) and (90)(sub 8) laminae, using AGLPLY, METCAN, and Battelle's Unit Cell FEA model. Results from the analyses were encouraging.

Newaz, Golam M.↗

In-phase thermomechanical fatigue mechanisms in an unidirectional SCS-6/Ti 15-3 MMC

The objective of this investigation was to identify the inelastic deformation and damage mechanisms under in-phase (IP) thermomechanical fatigue (TMF) in a unidirectional SCS-6/Ti 15-3 metal matrix composite (MMC). Load-controlled IP TMF tests were conducted at 300-538 C at various stress ranges in high-purity argon. A major emphasis of this work was to identify damage mechanism well before final fracture of specimens, rather than to generate life diagrams, to aid development of a realistic deformation/damage and life model.

Newaz, Golam M.↗

Inelastic deformation mechanisms in a transverse MMC lamina under compression

An investigation was undertaken to study the inelastic deformation mechanisms in (90)(sub 8) Ti 15-3/SCS-6 lamina subjected to pure compression. Both mechanical behavior and microstructural evaluation were undertaken at room temperature, 538 and 650 C. Results indicate that mechanical response and deformation characteristics are significantly different in monotonic tension and compression. The inelastic deformation mechanisms in compression are controlled by radial fiber fracture, matrix plasticity and fiber-matrix debonding. The radial fiber fracture is a new damage mode observed for metal-matrix composites (MMC).

Newaz, Golam M.↗

Correlating PMC-MMC Bonded Joint 3D FEA with Test

A viewgraph presentation on the correlation of Polymer Matrix Composites (PMC) and Metal Matrix Composites (MMC) bonded joints using three dimensional finite element analyses with materials tests is shown.

Jacobson, Mindy↗

Ultrasound spectroscopy: application on MMC and PMC materials

Resonant Ultrasound Spectroscopy (RUS) is a simple technique for measuring the second-order elastic constants and ultrasonic attenuation of solids. The technique is based on measuring the spectrum of mechanical resonances for a sample of known shape (usually a sphere, cylinder, or parallelepiped). This spectrum cannot be deconvoluted to deduce the elastic constants. Instead, an approximate spectrum is calculated from the known sample dimensions, its mass, and a set of 'guessed' elastic constants. A multidimensional minimization of the rms difference between the measured and calculated spectra enables us to deduce all the elastic constants of the solid from a single frequency scan. Currently, the technique can be applied to crystals of orthorhombic symmetry (9 elastic constants) or higher using desktop computers and software developed for this purpose. Composite materials, especially fiber composites, can take full advantage of the RUS technique as they typically have low symmetry. In this paper we summarize the RUS technique and provide examples of its application to the elastic characterization of both fiber reinforced MMC's, and fiber reinforced PMC's.

36 MATERIALS SCIENCE↗