Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mercury Dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Interim Results from a Study of the Impacts of Tin(II) Based Mercury Treatment in a Small Stream Ecosystem: Tims Branch, Savannah River Site

A research team is assessing the impacts of an innovative mercury treatment system in Tims Branch, a small southeastern stream. The treatment system, installed in 2007, reduces and removes inorganic mercury from water using tin(II) (stannous) chloride addition followed by air stripping. The system results in discharge of inorganic tin to the ecosystem. This screening study is based on historical information combined with measurements of contaminant concentrations in water, fish, sediment, biofilms and invertebrates. Initial mercury data indicate that first few years of mercury treatment resulted in a significant decrease in mercury concentration in an upper trophic level fish, redfin pickerel, at all sampling locations in the impacted reach. For example, the whole body mercury concentration in redfin pickerel collected from the most impacted pond decreased approximately 72% between 2006 (pre-treatment) and 2010 (post-treatment). Over this same period, mercury concentrations in the fillet of redfin pickerel in this pond were estimated to have decreased from approximately 1.45 μg/g (wet weight basis) to 0.45 μg/g - a decrease from 4.8x to 1.5x the current EPA guideline concentration for mercury in fillet (0.3 μg/g). Thermodynamic modeling, scanning electron microscopy, and other sampling data for tin suggest that particulate tin (IV) oxides are a significant geochemical species entering the ecosystem with elevated levels of tin measured in surficial sediments and biofilms. Detectable increases in tin in sediments and biofilms extended approximately 3km from the discharge location. Tin oxides are recalcitrant solids that are relatively non-toxic and resistant to dissolution. Work continues to develop and validate methods to analyze total tin in the collected biota samples. In general, the interim results of this screening study suggest that the treatment process has performed as predicted and that the concentration of mercury in upper trophic level fish, as a surrogate for all of the underlying transport and transformation processes in a complex ecosystem, has declined as a direct result of the elimination of inorganic mercury inputs. Inorganic tin released to the ecosystem has been found in compartments where particles accumulate with notable levels measured in biofilms.

54 ENVIRONMENTAL SCIENCES↗

TREATMENT TANK CORROSION STUDIES FOR THE ENHANCED CHEMICAL CLEANING PROCESS

Radioactive waste is stored in high level waste tanks on the Savannah River Site (SRS). Savannah River Remediation (SRR) is aggressively seeking to close the non-compliant Type I and II waste tanks. The removal of sludge (i.e., metal oxide) heels from the tank is the final stage in the waste removal process. The Enhanced Chemical Cleaning (ECC) process is being developed and investigated by SRR to aid in Savannah River Site (SRS) High-Level Waste (HLW) as an option for sludge heel removal. Corrosion rate data for carbon steel exposed to the ECC treatment tank environment was obtained to evaluate the degree of corrosion that occurs. These tests were also designed to determine the effect of various environmental variables such as temperature, agitation and sludge slurry type on the corrosion behavior of carbon steel. Coupon tests were performed to estimate the corrosion rate during the ECC process, as well as determine any susceptibility to localized corrosion. Electrochemical studies were performed to develop a better understanding of the corrosion mechanism. The tests were performed in 1 wt.% and 2.5 wt.% oxalic acid with HM and PUREX sludge simulants. The following results and conclusions were made based on this testing: (1) In 1 wt.% oxalic acid with a sludge simulant, carbon steel corroded at a rate of less than 25 mpy within the temperature and agitation levels of the test. No susceptibility to localized corrosion was observed. (2) In 2.5 wt.% oxalic acid with a sludge simulant, the carbon steel corrosion rates ranged between 15 and 88 mpy. The most severe corrosion was observed at 75 C in the HM/2.5 wt.% oxalic acid simulant. Pitting and general corrosion increased with the agitation level at this condition. No pitting and lower general corrosion rates were observed with the PUREX/2.5 wt.% oxalic acid simulant. The electrochemical and coupon tests both indicated that carbon steel is more susceptible to localized corrosion in the HM/oxalic acid environment than in the PUREX/oxalic acid environment. (3) The corrosion rates for PUREX/8 wt.% oxalic acid were greater than or equal to those observed for the PUREX/2.5 wt.% oxalic acid. No localized corrosion was observed in the tests with the 8 wt.% oxalic acid. Testing with HM/8 wt.% oxalic acid simulant was not performed. Thus, a comparison with the results with 2.5 wt.% oxalic acid, where the corrosion rate was 88 mpy and localized corrosion was observed at 75 C, cannot be made. (4) The corrosion rates in 1 and 2.5 wt.% oxalic acid solutions were temperature dependent: (a) At 50 C, the corrosion rates ranged between 90 to 140 mpy over the 30 day test period. The corrosion rates were higher under stagnant conditions. (b) At 75 C, the initial corrosion rates were as high as 300 mpy during the first day of exposure. The corrosion rates increased with agitation. However, once the passive ferrous oxalate film formed, the corrosion rate decreased dramatically to less than 20 mpy over the 30 day test period. This rate was independent of agitation. (5) Electrochemical testing indicated that for oxalic acid/sludge simulant mixtures the cathodic reaction has transport controlled reaction kinetics. The literature suggests that the dissolution of the sludge produces a di-oxalatoferrate ion that is reduced at the cathodic sites. The cathodic reaction does not appear to involve hydrogen evolution. On the other hand, electrochemical tests demonstrated that the cathodic reaction for corrosion of carbon steel in pure oxalic acid involves hydrogen evolution. (6) Agitation of the oxalic acid/sludge simulant mixtures typically resulted in a higher corrosion rates for both acid concentrations. The transport of the ferrous ion away from the metal surface results in a less protective ferrous oxalate film. (7) A mercury containing species along with aluminum, silicon and iron oxides was observed on the interior of the pits formed in the HM/2.5 wt.% oxalic acid simulant at 75 C. The pitting rates in the agitated and non-agitated solution were 2 mils/day and 1 mil/day, respectively. A mechanism by which the mercury interacts with the aluminum and silicon oxides in this simulant to accelerate corrosion was proposed.

08 HYDROGEN↗

Catalytic Effects of Silver in Iodine Reactors for Dissolved Used Nuclear Fuel

The dissolution of used nuclear fuel generates a variety of off-gasses including flammable hydrogen and other species that are a concern for environmental release. The H-Canyon facility at the Savannah River Site is currently dissolving aluminum-clad research reactor fuel from material test reactors and the High Flux Isotope Reactor (HFIR) using a mercury-catalyzed nitric acid flowsheet. Savannah River National Laboratory recently developed and deployed a Raman spectrometer to monitor the off-gas stream from the dissolution process. Results from these measurements indicated a lack of the expected hydrogen, nitrous oxide, and nitric oxide in the off-gas stream. It was proposed that the silver on the silver nitrate–coated berl saddles present in the reactors for iodine capture were acting as a catalytic hydrogen recombiner. Nitric oxide is readily oxidized to nitrogen dioxide under normal conditions, but it was unclear what happened to the nitrous oxide. A laboratory-scale iodine reactor was assembled and filled with silver nitrate–coated berl saddles to help ascertain the fate of nitrous oxide and hydrogen. Testing with this laboratory-scale reactor observed the recombination of hydrogen when a simulated dissolver off-gas was passed through the reactor containing silver nitrate–coated berl saddles at the approximate temperatures seen in H-Canyon. However, the nitrous oxide concentration was unchanged, suggesting a more complex process occurring within the off-gas stream before it reaches the iodine reactors at H-Canyon.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ADVANCED OXIDATION: OXALATE DECOMPOSITION TESTING WITH OZONE

At the Savannah River Site (SRS), oxalic acid is currently considered the preferred agent for chemically cleaning the large underground Liquid Radioactive Waste Tanks. It is applied only in the final stages of emptying a tank when generally less than 5,000 kg of waste solids remain, and slurrying based removal methods are no-longer effective. The use of oxalic acid is preferred because of its combined dissolution and chelating properties, as well as the fact that corrosion to the carbon steel tank walls can be controlled. Although oxalic acid is the preferred agent, there are significant potential downstream impacts. Impacts include: (1) Degraded evaporator operation; (2) Resultant oxalate precipitates taking away critically needed operating volume; and (3) Eventual creation of significant volumes of additional feed to salt processing. As an alternative to dealing with the downstream impacts, oxalate decomposition using variations of ozone based Advanced Oxidation Process (AOP) were investigated. In general AOPs use ozone or peroxide and a catalyst to create hydroxyl radicals. Hydroxyl radicals have among the highest oxidation potentials, and are commonly used to decompose organics. Although oxalate is considered among the most difficult organic to decompose, the ability of hydroxyl radicals to decompose oxalate is considered to be well demonstrated. In addition, as AOPs are considered to be 'green' their use enables any net chemical additions to the waste to be minimized. In order to test the ability to decompose the oxalate and determine the decomposition rates, a test rig was designed, where 10 vol% ozone would be educted into a spent oxalic acid decomposition loop, with the loop maintained at 70 C and recirculated at 40L/min. Each of the spent oxalic acid streams would be created from three oxalic acid strikes of an F-area simulant (i.e., Purex = high Fe/Al concentration) and H-area simulant (i.e., H area modified Purex = high Al/Fe concentration) after nearing dissolution equilibrium, and then decomposed to {le} 100 Parts per Million (ppm) oxalate. Since AOP technology largely originated on using ultraviolet (UV) light as a primary catalyst, decomposition of the spent oxalic acid, well exposed to a medium pressure mercury vapor light was considered the benchmark. However, with multi-valent metals already contained in the feed, and maintenance of the UV light a concern; testing was conducted to evaluate the impact from removing the UV light. Using current AOP terminology, the test without the UV light would likely be considered an ozone based, dark, ferrioxalate type, decomposition process. Specifically, as part of the testing, the impacts from the following were investigated: (1) Importance of the UV light on the decomposition rates when decomposing 1 wt% spent oxalic acid; (2) Impact of increasing the oxalic acid strength from 1 to 2.5 wt% on the decomposition rates; and (3) For F-area testing, the advantage of increasing the spent oxalic acid flowrate from 40 L/min (liters/minute) to 50 L/min during decomposition of the 2.5 wt% spent oxalic acid. The results showed that removal of the UV light (from 1 wt% testing) slowed the decomposition rates in both the F & H testing. Specifically, for F-Area Strike 1, the time increased from about 6 hours to 8 hours. In H-Area, the impact was not as significant, with the time required for Strike 1 to be decomposed to less than 100 ppm increasing slightly, from 5.4 to 6.4 hours. For the spent 2.5 wt% oxalic acid decomposition tests (all) without the UV light, the F-area decompositions required approx. 10 to 13 hours, while the corresponding required H-Area decompositions times ranged from 10 to 21 hours. For the 2.5 wt% F-Area sludge, the increased availability of iron likely caused the increased decomposition rates compared to the 1 wt% oxalic acid based tests. In addition, for the F-testing, increasing the recirculation flow rates from 40 liter/minute to 50 liter/minute resulted in an increased decomposition rate, suggesting a better use of ozone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Curing process and pore structure of metakaolin-based geopolymers: Liquid-state 1H NMR investigation

Geopolymers are emerging construction materials with lower carbon dioxide emissions compared to the conventional cementitious materials. The knowledge of the curing process and the related pore structures are important for optimizing the properties of these materials for different applications. The curing process and final pore structure are sensitive to the amount of used water, however the specifics are unclear. The curing process and pore structures of metakaolin-based geopolymers with a narrow water-to-solid (w/s) ratio (0.59–0.66) were monitored by nuclear magnetic resonance (NMR) relaxometry and cryoporometry. The 14-day curing process was investigated by monitoring the change of T{sub 2} and T{sub 1} relaxation times and water signal intensity. After the curing, the pore structures were characterized by 2D T{sub 1}-T{sub 2} correlation and T{sub 2}-T{sub 2} exchange measurements of absorbed water. The pore size distributions (PSDs) were measured with NMR cryoporometry and compared to nitrogen physisorption and mercury intrusion porosimetry (MIP) results. We found that the relaxation times decreased as the pore structure of the geopolymers matured during the curing while the dissolution and the condensation periods of the curing were distinguished by the changes in signal amplitude reflecting the proton density. After the curing, three distinct pore sizes and connectivity between pores were identified from T{sub 1}-T{sub 2} and T{sub 2}-T{sub 2} spectra. Their PSDs were measured, and they were found to correspond to two different pore sizes originating from the arrangement of clusters and defective pores. In the narrow w/s ratio (0.59–0.66), the curing times were the same for all samples when cured at 24 °C while the pore sizes were observed to increase as a function of the w/s ratio.

36 MATERIALS SCIENCE↗

Elemental analysis of printed circuit boards considering the ROHS regulations

The EU RoHS Directive (2002/95/EC of the European Parliament and of the Council) bans the placing of new electrical and electronic equipment containing more than agreed levels of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants on the EU market. It necessitates methods for the evaluation of RoHS compliance of assembled electronic equipment. In this study mounted printed circuit boards from personal computers were analyzed on their content of the three elements Cd, Pb and Hg which were limited by the EU RoHS directive. Main focus of the investigations was the influence of sample pre-treatment on the precision and reproducibility of the results. The sample preparation steps used were based on the guidelines given in EN 62321. Five different types of dissolution procedures were tested on different subsequent steps of sample treatment like cutting and milling. Elemental analysis was carried out using ICP-OES, XRF and CV-AFS (Hg). The results obtained showed that for decision-making with respect to RoHS compliance a size reduction of the material to be analyzed to particles {<=}1.5 mm can already be sufficient. However, to ensure analytical results with relative standard deviations of less than 20%, as recommended by the EN 62321, a much larger effort for sample processing towards smaller particle sizes might be required which strongly depends on the mass fraction of the element under investigation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Life support systems research at the Johnson Space Center

The bioregenerative life support systems research at Johnson Space Center focuses on the use of lunar regolith as a plant growth medium. Current dissolution experiments are being conducted to ascertain the response of lunar regolith to various solvents and weathering environments. The transformation of lunar minerals into minerals such as zeolites which would be more conducive to plant growth is also investigated. A study is currently underway to examine the ability of zeolite/apatite mixtures to provide N, P, and K through dissolution and ion exchange. The development and characterization of simulated lunar regolith for preliminary experimentation are also discussed. The life support systems technology used on the Mercury, Gemini, Apollo, and Shuttle missions is reviewed and current research on regenerative life support systems technology for potential use in Space Station Freedom is discussed.

Henninger, D. L.↗

DISSOLUTION OF IRRADIATED MURR FUEL ASSEMBLIES EFFECT OF INCREASED PURGE RATE AND CATALYST CONCENTRATION ON THE BATCH SIZE

Flowsheets for the dissolution of aluminum-clad spent nuclear fuel have been proposed using 0.002 M mercuric nitrate catalyst in 5 to 6 M nitric acid. Previous calculations for flammable gas control during the dissolution of spent nuclear fuel have been extended to cover a range of dissolver purge rates from 40 to 55 scfm. A range of dissolver solution volumes from 12000 to 15000 liters were considered for the large H-Canyon dissolver (6.4D). Depending on the purge rate, anywhere from four to six bundles of MURR fuel can be initially charged to the dissolver (6.4D). For successive charges where the dissolver solution already contains 0.002 M mercury catalyst and the dissolved aluminum from five bundles of MURR fuel, five to nine bundles of additional fuel can be charged depending on the purge rate and the dissolver solution volume. Similar calculations have been performed for the small H-Canyon dissolver (6.1D) for solution volumes that ranged from 6000 to 7500 liters and purge rates from 40 to 55 scfm. The limitations on the initial charge are four to six bundles depending on the purge rate. The aluminum from four bundles of fuel in an initial charge will allow nine to ten bundles in the second charge to 6.1D depending on the purge rate and dissolver solution volume. Solubility or criticality limitations will restrict the second charge on the small dissolver. The concentration of aluminum from previous charges will slow the dissolution rate to extend the cycle time of repeated charges of fuel. Calculations have been performed to allow a second catalyst addition (up to 0.004 M total catalyst) to reduce the cycle time (as necessary) based on the aluminum concentration and the purge rate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modeling CO 2 -Brine-Rock Interaction Including Mercury and H 2 S Impurities in the Context of CO 2 Geologic Storage

This study uses modeling and simulation approaches to investigate the impacts on injectivity of trace amounts of mercury (Hg) in a carbon dioxide (CO 2 ) stream injected for geologic carbon sequestration in a sandstone reservoir at ~2.5 km depth. At the range of Hg concentrations expected (7-190 ppbV, or ~ 0.06-1.6 mg/std.m 3 CO 2 ), the total volumetric plugging that could occur due to complete condensation of Hg, or due to complete precipitation of Hg as cinnabar, results in a very small porosity change. In addition, Hg concentration much higher than the concentrations considered here would be required for Hg condensation to even occur. Concentration of aqueous Hg by water evaporation into CO 2 is also unlikely because the higher volatility of Hg relative to H 2 O at reservoir conditions prevents the Hg concentration from increasing in groundwater as dry CO 2 sweeps through, volatilizing both H 2 O and Hg. Using a model-derived aqueous solution to represent the formation water, batch reactive geochemical modeling show that the reaction of the formation water with the CO 2 -Hg mixture causes the pH to drop to about 4.7 and then become buffered near 5.2 upon reaction with the sediments, with a negligible net volume change from mineral dissolution and precipitation. Cinnabar (HgS(s)) is found to be thermodynamically stable as soon as the Hg-bearing CO 2 reacts with the formation water which contains small amounts of dissolved sulfide. Liquid mercury (Hg(l)) is not found to be thermodynamically stable at any point during the simulation. Two-dimensional radial reactive transport simulations of CO 2 injection at a rate of 14.8 kg/s into a 400 m-thick formation at isothermal conditions of 106°C and average pressure near 215 bar, with varying amounts of Hg and H 2 S trace gases, show generally that porosity changes only by about ±0.05% (absolute, i.e., new porosity = initial porosity ±0.0005) with Hg predicted to readily precipitate from the CO 2 as cinnabar in a zone mostly matching the single-phase CO 2 plume. The precipitation of minerals other than cinnabar, however, dominates the evolution of porosity. Main reactions include the replacement of primarily Fe-chlorite by siderite, of calcite by dolomite, and of K-feldspar by muscovite. Chalcedony is also predicted to precipitate from the dissolution of feldspars and quartz. Although the range of predicted porosity change is quite small, the amount of dissolution and precipitation predicted for these individual minerals is not negligible. These reactive transport simulations assume that Hg gas behaves ideally. To examine effects of non-ideality on these simulations, approximate calculations of the fugacity coefficient of Hg in CO 2 were made. Results suggest that Hg condensation could be significantly overestimated when assuming ideal gas behavior, making our simulation results conservative with respect to impacts on injectivity. The effect of pressure on Henry’s constant for Hg is estimated to yield Hg solubilities about 10% lower than when this effect is not considered, a change that is considered too small to affect the conclusions of this report. Although all results in this study are based on relatively mature data and modeling approaches, in the absence of experimental data and more detailed site-specific information, it is not possible to fully validate the results and conclusions.

54 ENVIRONMENTAL SCIENCES↗

Investigating Si Bonding Environments in Mercurian Melts

Mercury’s low oxygen fugacity results in lavas with extraordinarily high sulfur contents (> 1 wt%). The high S lowers melt viscosity, but why this occurs is unclear (Mouser et al., 2021). The detection of Si-S bonds (using NMR) in such highly reduced basaltic glasses, suggest that the decreased viscosity is due to changes in the Si bonding environment (Pommier et al., 2023). To investigate further, we synthesized a series of Mercurian glasses at 1 GPa, with S contents ranging from 0-6 wt% and oxygen fugacities from IW-4 to IW-6. The experimental glasses were analyzed by Si K-edge X-ray Absorption Near Edge Structure (XANES) spectroscopy and 29Si Nuclear Magnetic Resonance (NMR). Ongoing analyses will include Raman and Fourier Transform Infrared (FTIR). The 29Si NMR analyses suggest the presence of Si-S bonds in the melts, in agreement with Pommier et al. (2023). The Si K-edge XANES spectra show a decrease in K-edge position of 0.4 to 0.6 eV from terrestrial basalts (at ~IW+3) to the experimental melts at IW-4 to IW-6. This shift suggests a moderate (<20 mole %) amount of Si has shifted to lower valence states (Boujibar et al, 2019). The melts contain 0-6 wt% S, so if the K-edge shifts are the results of Si-S bonding, it implies that the majority of the S in the melts is bonded to Si. However, S K-edge XANES analyses indicate that much of the S is also bonded with Mg and Ca at these low oxygen fugacities (Anzures et al, 2020). The implication is that non-bridging Si-S-(Mg,Ca) bonds are prevalent in the reduced melts, consistent with the decrease in viscosity of the melts being due to melt depolymerization. Overall, our results suggest that dissolution of S into the melts at low fO2 is accomplished through bonding with Si, and is accompanied by significant structural changes that lower melt viscosity. Lower melt viscosities will affect many aspects of Mercury’s evolution, from magma ocean dynamics, to melt migration in the mantle, to eruption dynamics and degassing.

Emily L Fischer↗

Nucleation and Growth of PbBrF Crystals at the Liquid Mercury–Electrolyte Interface Studied by Operando X-ray Scattering

In this work, detailed in operando studies of electrochemically induced PbBrF deposition at the liquid mercury/liquid electrolyte interface are presented. The nucleation and growth were monitored using time-resolved X-ray diffraction and reflectivity combined with electrochemical measurements, revealing a complex potential-dependent behavior. PbBrF deposition commences at potentials above –0.7 V with the rapid formation of an ultrathin adlayer of one unit cell thickness, on top of which (001)-oriented three-dimensional crystallites are formed. Two potential regimes are identified. At low overpotentials, slow growth of a low surface density film of large crystals is observed. At high overpotentials, crossover to a potential-independent morphology occurs, consisting of a compact PbBrF deposit with a saturation thickness of 25 nm, which forms within a few minutes. This potential behavior can be rationalized by the increasing supersaturation near the interface, caused by the potential-dependent Pb2+ deamalgamation, which changes from a slow reaction-controlled process to a fast transport-controlled process in this range of overpotentials. In addition, growth on the liquid substrate is found to involve complex micromechanical effects, such as crystal reorientation and film breakup during dissolution.

36 MATERIALS SCIENCE↗

Nanoscale Interfacial Smoothing and Dissolution during Unconventional Reservoir Stimulation Implications for Hydrocarbon Mobilization and Transport

Hydraulic fracturing of low-permeability rocks significantly enhances hydrocarbon production from unconventional reservoirs. However, fluid transport through low-permeability rocks, and the influence of geochemical transformations on pore networks, are poorly constrained. Mineral reactivity during interactions with injected water may alter the physical nature of the rock, which may affect hydrocarbon mobility. To assess alteration to the rock, we previously conducted a hydrothermal experiment that reacted cubed rock samples (1 cm3) with synthetic hydraulic fracturing fluid to simulate physicochemical reactivity during hydraulic fracturing. We analyzed unreacted and reacted rocks by small-angle neutron scattering and high-pressure mercury intrusion to determine how nanoscale (~1-1400 nm) pore networks of unconventional reservoir rocks are influenced by reaction with hydraulic fracturing injectates. We show that fluid-rock interactions have a two-fold influence on hydrocarbon recovery, promoting both hydrocarbon mobilization and transport. Pore-matrix interfaces smooth via removal of clay mineral surface asperities, reducing available surface area for hydrocarbon adsorption by ca. 12-75%. Additionally, hydraulic fracturing fluid-induced dissolution creates new pores with diameters ranging in size from 800-1400 nm, increasing the permeability of the rocks by a factor of 5-10. These two consequences of mineral dissolution act in concert to release hydrocarbons from the host rock and facilitate transport through the rock during unconventional reservoir production.

Herz-Thyhsen, Ryan↗

Dissolution Flowsheet for High Flux Isotope Reactor Fuel

As part of the Spent Nuclear Fuel (SNF) processing campaign, H-Canyon is planning to begin dissolving High Flux Isotope Reactor (HFIR) fuel in late FY17 or early FY18. Each HFIR fuel core contains inner and outer fuel elements which were fabricated from uranium oxide (U 3 O 8 ) dispersed in a continuous Al phase using traditional powder metallurgy techniques. Fuels fabricated in this manner, like other SNF’s processed in H-Canyon, dissolve by the same general mechanisms with similar gas generation rates and the production of H 2 . The HFIR fuel cores will be dissolved and the recovered U will be down-blended into low-enriched U. HFIR fuel was previously processed in H-Canyon using a unique insert in both the 6.1D and 6.4D dissolvers. Multiple cores will be charged to the same dissolver solution maximizing the concentration of dissolved Al. The objective of this study was to identify flowsheet conditions through literature review and laboratory experimentation to safely and efficiently dissolve the HFIR fuel in H-Canyon. Laboratory-scale experiments were performed to evaluate the dissolution of HFIR fuel using both Al 1100 and Al 6061 T6 alloy coupons. The Al 1100 alloy was considered a representative surrogate which provided an upper bound on the generation of flammable (i.e., H 2 ) gas during the dissolution process. The dissolution of the Al 6061 T6 alloy proceeded at a slower rate than the Al 1100 alloy, and was used to verify that the target Al concentration in solution could be achieved for the selected Hg concentration. Mass spectrometry and Raman spectroscopy were used to provide continuous monitoring of the concentration of H 2 and other permanent gases in the dissolution offgas, allowing the development of H 2 generation rate profiles. The H 2 generation rates were subsequently used to evaluate if a full HFIR core could be dissolved in an H-Canyon dissolver without exceeding 60% of the calculated lower flammability limit (LFL) for H 2 at a given Hg concentration. Complete dissolution of the Al 1100 and Al 6061 T6 alloys up to a final Al concentration of 2 M was obtained using a 7 M HNO 3 solution containing a 0.002 M Hg catalyst. However, following the dissolutions, solids were observed in the solution. The solids were amorphous, but likely originated from the Si present in the alloys. No crystalline materials, such as Al(NO 3 ) 3 were observed. During the course of the dissolution experiments, it was determined that delaying the addition of Hg once the HNO 3 solution reached the boiling point can reduce the total offgas and H 2 generation rates. The delay in starting the Hg addition is not necessary for HFIR fuel dissolution, but could be useful in other research reactor dissolution campaigns. The potential to generate flammable concentrations of H 2 in the offgas during a HFIR fuel dissolution was evaluated using the experimental data. The predicted H 2 concentration in the dissolver offgas stream was compared with 60% of the calculated H 2 LFL at 200 °C using several prototypical experiments. The calculations showed that a full HFIR core can be dissolved using nominally 0.002 M Hg to catalyze the dissolution. The margin between the predicted H 2 concentration and the calculated LFL was greater when the solution was allowed to boil for 45 min prior to initiating the Hg addition. When the Hg was increased to 0.004 M, the predicted H 2 concentration exceeded the calculated LFL early in the dissolution. The dissolution experiments also demonstrated that additional Hg (beyond the initial 0.002 M) could be added as the Al concentration increases. The ability to add more Hg during a HFIR fuel dissolution could be beneficial if slow dissolution rates are observed at high Al concentrations. Experimental data were used to demonstrate that the predicted H 2 concentration in a dissolver was below 60% of the calculated LFL at 200 °C when 0.004 M Hg was used to catalyze the dissolution if the Al concentration is conservatively greater than 0.5 M. Data also show that the Hg concentration during a HFIR fuel dissolution can be increased from 0.002 to 0.008 M at an Al concentration of 1.3 M.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-Synthetic Mannich Chemistry on Metal-Organic Frameworks: System-Specific Reactivity and Functionality-Triggered Dissolution

he Mannich reaction of the zirconium MOF [Zr6O4 (OH)4 (bdc-NH2 )6 ] (UiO-66-NH2 , bdc-NH2=2-amino-1,4- benzenedicarboxylate) with paraformaldehyde and pyrazole, imidazole or 2-mercaptoimidazole led to post-synthetic modification (PSM) through C@N bond formation. The reaction with imidazole (Him) goes to completion whereas those with pyrazole (Hpyz) and 2-mercaptoimidazole (HimSH) give up to 41 and 36% conversion, respectively. The BET surface areas for the Mannich products are reduced from that of UiO-66-NH2 , but the compounds show enhanced selectivity for adsorption of CO2 over N2 at 273 K. The thiol-containing MOFs adsorb mercury(II) ions from aqueous solution, removing up to 99%. The Mannich reaction with pyrazole succeeds on [Zn4O(bdc-NH2 )3 ] (IRMOF-3), but a similar reaction on [Zn2 (bdc-NH2 )2 (dabco)] (dabco=1,4-diazabicyclo[2.2.2]octane) gave [Zn3 (bdc-NH2 )1.32(bdc-NHCH2pyz)1.68(dabco)]·2C7H8 5, whereas the reaction with imidazole gave the expected PSM product. Compound 5 forms via a dissolution–recrystallisation process that is triggered by the “free” pyrazolate nitrogen atom competing with dabco for coordination to the zinc(II) centre. In contrast, the “free” nitrogen atom on the imidazolate is too far away to compete in this way. Mannich reactions on [In(OH)(bdc-NH2 )] (MIL-68(In)-NH2 ) stop after the first step, and the product was identified as [In(OH)(bdcNH2 )0.41(bdc-NHCH2OCH3 )0.30(bdc-N=CH2 )0.29], with addition of the heterocycle prevented by steric interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Toxicity mitigation and solidification of municipal solid waste incinerator fly ash using alkaline activated coal ash

Highlights: Black-Right-Pointing-Pointer Incinerator fly ash (IFA) is added to an alkali activated coal fly ash (CFA) matrix. Black-Right-Pointing-Pointer Means of stabilizing the incinerator ash for use in construction applications. Black-Right-Pointing-Pointer Concrete made from IFA, CFA and IFA-CFA mixes was chemically characterized. Black-Right-Pointing-Pointer Environmentally friendly solution to IFA disposal by reducing its toxicity levels. - Abstract: Municipal solid waste (MSW) incineration is a common and effective practice to reduce the volume of solid waste in urban areas. However, the byproduct of this process is a fly ash (IFA), which contains large quantities of toxic contaminants. The purpose of this research study was to analyze the chemical, physical and mechanical behaviors resulting from the gradual introduction of IFA to an alkaline activated coal fly ash (CFA) matrix, as a mean of stabilizing the incinerator ash for use in industrial construction applications, where human exposure potential is limited. IFA and CFA were analyzed via X-ray fluorescence (XRF), X-ray diffraction (XRD) and Inductive coupled plasma (ICP) to obtain a full chemical analysis of the samples, its crystallographic characteristics and a detailed count of the eight heavy metals contemplated in US Title 40 of the Code of Federal Regulations (40 CFR). The particle size distribution of IFA and CFA was also recorded. EPA's Toxicity Characteristic Leaching Procedure (TCLP) was followed to monitor the leachability of the contaminants before and after the activation. Also images obtained via Scanning Electron Microscopy (SEM), before and after the activation, are presented. Concrete made from IFA, CFA and IFA-CFA mixes was subjected to a full mechanical characterization; tests include compressive strength, flexural strength, elastic modulus, Poisson's ratio and setting time. The leachable heavy metal contents (except for Se) were below the maximum allowable limits and in many cases even below the reporting limit. The leachable Chromium was reduced from 0.153 down to 0.0045 mg/L, Arsenic from 0.256 down to 0.132 mg/L, Selenium from 1.05 down to 0.29 mg/L, Silver from 0.011 down to .001 mg/L, Barium from 2.06 down to 0.314 mg/L and Mercury from 0.007 down to 0.001 mg/L. Although the leachable Cd exhibited an increase from 0.49 up to 0.805 mg/L and Pd from 0.002 up to 0.029 mg/L, these were well below the maximum limits of 1.00 and 5.00 mg/L, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Flammability Control In A Nuclear Waste Vitrification System

The Defense Waste Processing Facility at the Savannah River Site processes high-level radioactive waste from the processing of nuclear materials that contains dissolved and precipitated metals and radionuclides. Vitrification of this waste into borosilicate glass for ultimate disposal at a geologic repository involves chemically modifying the waste to make it compatible with the glass melter system. Pretreatment steps include removal of excess aluminum by dissolution and washing, and processing with formic and nitric acids to: 1) adjust the reduction-oxidation (redox) potential in the glass melter to reduce radionuclide volatility and improve melt rate; 2) adjust feed rheology; and 3) reduce by steam stripping the amount of mercury that must be processed in the melter. Elimination of formic acid in pretreatment has been studied to eliminate the production of hydrogen in the pretreatment systems, which requires nuclear grade monitoring equipment. An alternative reductant, glycolic acid, has been studied as a substitute for formic acid. However, in the melter, the potential for greater formation of flammable gases exists with glycolic acid. Melter flammability is difficult to control because flammable mixtures can be formed during surges in offgases that both increase the amount of flammable species and decrease the temperature in the vapor space of the melter. A flammable surge can exceed the 60% of the LFL with no way to mitigate it. Therefore, careful control of the melter feed composition based on scaled melter surge testing is required. The results of engineering scale melter tests with the formic-nitric flowsheet and the use of these data in the melter flammability model are presented.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of Carbonic Acid-Rock Interactions on CO2/Brine Multiphase Flow Properties in the Upper Minnelusa Sandstones

Summary Carbon dioxide (CO2) injection into a deep saline aquifer can dissolve into formation brine and generate carbonic acid. The resulting acid can drive fluid-rock geochemical reactions. The impact of these fluid-rock geochemical reactions on porosity, permeability, and multiphase flow responses is relevant to the determination of CO2 storage capacity of deep saline aquifers. In this research, carbonic acid flooding experiments were performed on core samples consisting of poorly sorted, quartz-rich sand with laminated bedding from a possible CO2 storage target in northwest Wyoming. Complementary pre- and post-injection porosity and permeability, thin-section, Brunauer-Emmett-Teller (BET) surface area, mercury intrusion capillary pressure (MICP), and time-domain nuclear magnetic resonance (TD-NMR) measurements were conducted. Overall, both core porosity and permeability increased after a 7-day carbonic acid injection, from 6.2 to 8.4% and 1.6 to 3.7 md, respectively. We attributed these changes to carbonate mineral dissolution, which was evidenced by the effluent brine geochemistry, pore-throat size distribution (PTSD), and BET surface area. To be more specific, within the more-permeable section of core samples containing larger pore size, the permeability increment is apparent due to dolomite mineral grains and cements dissolution. However, for the lower-permeability section corresponding to the smaller pore size, mineral precipitation possibly lessened dissolution effects, leading to insignificant petrophysical properties changes. Consequently, the observed heterogeneous carbonic acid-rock interactions resulted in alterations of CO2/brine relative permeability (i.e., the initial CO2 saturation decreased and the CO2 flow capacity was enhanced). This research provides a fundamental understanding regarding effects of fluid-rock reactions on changes in static and multiphase flow properties of eolian sandstones, which lays the foundation for more accurate prediction/simulation of CO2 injection into deep saline aquifers.

Engineering↗