Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mesh optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Recent Improvements in Aerodynamic Design Optimization on Unstructured Meshes

Recent improvements in an unstructured-grid method for large-scale aerodynamic design are presented. Previous work had shown such computations to be prohibitively long in a sequential processing environment. Also, robust adjoint solutions and mesh movement procedures were difficult to realize, particularly for viscous flows. To overcome these limiting factors, a set of design codes based on a discrete adjoint method is extended to a multiprocessor environment using a shared memory approach. A nearly linear speedup is demonstrated, and the consistency of the linearizations is shown to remain valid. The full linearization of the residual is used to precondition the adjoint system, and a significantly improved convergence rate is obtained. A new mesh movement algorithm is implemented and several advantages over an existing technique are presented. Several design cases are shown for turbulent flows in two and three dimensions.

Nielsen, Eric J.↗
NASA NTRS2019

Adjoint-Based Mesh Adaptation and Shape Optimization for Simulations with Propulsion

We demonstrate a well-posed formulation of permeable boundary conditions and mass- flow-rate functionals for adjoint-based mesh refinement and shape optimization governed by the steady Euler equations. The boundary conditions are used to model propulsion- system effects of inlets and nozzles. A two-shock diffuser with an analytic solution is used to verify the implementation. Numerical examples show that the adjoint solution is smooth at the boundary, indicating that the discretization is adjoint consistent when exit pressure is specified at subsonic outflow, and stagnation temperature and pressure at subsonic inflow. The results focus on improving simulation techniques for low-boom aircraft analysis and design. By including mass-flow-rate outputs, we obtain reliable estimates of engine flow rates concurrently with nearfield pressure signatures without increasing simulation cost. We also demonstrate the importance of mass-flow-rate constraints in shape optimization by examining trade-offs between maximizing performance of a shrouded supersonic nozzle and minimizing shocks in its nearfield.

Nemec, Marian↗
DOE OSTI2024

Level-set topology optimization with PDE generated conformal meshes

This paper presents a level-set topology optimization approach that uses conformal meshes for the analysis of the displacement field. The structure’s boundary is represented by the iso-contour of a level-set field discretized on a fixed background design mesh. The conformal mesh is updated for each design iteration via a PDE based mesh morphing process that identifies the set of facets in the background mesh that are homeomorphic to the boundary and relaxes the homeomorphic mesh to conform to the structure’s boundary and ensure high element quality. The conformal mesh allows for a more accurate computation of the response versus density and some level-set based methods which interpolate material properties using the volume fraction. Numerical examples illustrate the proposed approach by optimizing linear-elastic two- and three-dimensional structures, wherein insight into the performance of the mesh morphing process is provided. The examples also highlight the scalability of the approach.

42 ENGINEERING↗
DOE OSTI2025

Advancing the STS Neutron Moderator Design with an Automated Optimization Workflow and Unstructured Mesh Modeling

With the Second Target Station approaching its final design phase, a detailed neutronics evaluation of its critical components is necessary. Optimizing the dimensions of the two cold-source moderators that are at the heart of this facility presents a multi-objective optimization problem for which an accurate geometric description is crucial. We have applied a fully automated optimization workflow in which a detailed unstructured mesh geometry is automatically generated with Attila4MC, starting from a parametrized CREO geometry followed by preprocessing with SpaceClaim. With this geometry, a MCNP run is performed to calculate the brightness metrics, which are subsequently provided to the optimization algorithm in DAKOTA that provides new parameters and drives the optimization loop until convergence. In this paper, we show the results of the analysis that are used for the final design of the cylindrical and tube moderator. The optimization simulations provide a refinement to and confirmation of the conclusions of the previous design iteration. Additional to the optimization, a sensitivity study is performed to study the effect of minor geometry changes, which is important for the final engineering design. In conclusion, with these studies, we demonstrate that the automated workflow and high-fidelity unstructured mesh modeling are efficient tools for a thorough design evaluation.

DAKOTA↗
NASA NTRS1973

A mesh gradient technique for numerical optimization

A class of successive-improvement optimization methods in which directions of descent are defined in the state space along each trial trajectory are considered. The given problem is first decomposed into two discrete levels by imposing mesh points. Level 1 consists of running optimal subarcs between each successive pair of mesh points. For normal systems, these optimal two-point boundary value problems can be solved by following a routine prescription if the mesh spacing is sufficiently close. A spacing criterion is given. Under appropriate conditions, the criterion value depends only on the coordinates of the mesh points, and its gradient with respect to those coordinates may be defined by interpreting the adjoint variables as partial derivatives of the criterion value function. In level 2, the gradient data is used to generate improvement steps or search directions in the state space which satisfy the boundary values and constraints of the given problem.

Willis, E. A., Jr.↗
NASA NTRS2019

Adjoint-Based Mesh Adaptation and Shape Optimization for Simulations with Propulsion

Objectives: Reliable evaluation of mass flow rates through permeable boundaries - Estimate and control discretization error- Consider both computational domain outflow and inflow- Applicable to simulating propulsion-system effects, as well as secondary flow paths - Explore feasibility of handling more general outputs at domain boundaries. Design optimization subject to mass-flow-rate constraints - Improve aerodynamic performance and reduce noise due to sonic boom - Control discretization error in design space to improve confidence in final designs.

Nemec, Marian↗
NASA NTRS2014

802.11s Wireless Mesh Network Visualization Application

Results of past experimentation at NASA Johnson Space Center showed that the IEEE 802.11s standard has better performance than the widely implemented alternative protocol B.A.T.M.A.N (Better Approach to Mobile Ad hoc Networking). 802.11s is now formally incorporated into the Wi- Fi 802.11-2012 standard, which specifies a hybrid wireless mesh networking protocol (HWMP). In order to quickly analyze changes to the routing algorithm and to support optimizing the mesh network behavior for our intended application a visualization tool was developed by modifying and integrating open source tools.

Mauldin, James Alexander↗
NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation high-lift 2D airfoil↗
NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation↗
NASA NTRS1987

Constrained sheath optics for high thrust density, low specific impulse ion thrusters

The results of an experimental study showing that a contoured, fine wire mesh attached to the screen grid can be used to control the divergence characteristics of ion beamlets produced at low net-to-total accelerating voltage ratios are presented. The influence of free and constrained-sheath optics systems on beamlet divergence characteristics are found to be similar in the operating regime investigated, but it was found that constrained-sheath optics systems can be operated at higher perveance levels than free-sheath ones. The concept of a fine wire interference probe that can be used to study ion beamlet focusing behavior is introduced. This probe is used to demonstrate beamlet focusing to a diameter about one hundreth of the screen grid extraction aperture diameter. Additional testing is suggested to define an optimally contoured mesh that could yield well focused beamlets at net-to-total accelerating voltage ratios below about 0.1.

Wilbur, Paul J.↗
NASA NTRS1993

Three-dimensional unstructured grid refinement and optimization using edge-swapping

This paper presents a three-dimensional (3-D) 'edge-swapping method based on local transformations. This method extends Lawson's edge-swapping algorithm into 3-D. The 3-D edge-swapping algorithm is employed for the purpose of refining and optimizing unstructured meshes according to arbitrary mesh-quality measures. Several criteria including Delaunay triangulations are examined. Extensions from two to three dimensions of several known properties of Delaunay triangulations are also discussed.

Gandhi, Amar↗
NASA NTRS1997

Error Estimation and h-Adaptivity for Optimal Finite Element Analysis

The objective of adaptive meshing and automatic error control in finite element analysis is to eliminate the need for the application engineer from re-meshing and re-running design simulations to verify numerical accuracy. The user should only need to enter the component geometry and a coarse finite element mesh. The software will then autonomously and adaptively refine this mesh where needed, reducing the error in the fields to a user prescribed value. The ideal end result of the simulation is a measurable quantity (e.g. scattered field, input impedance), calculated to a prescribed error, in less time and less machine memory than if the user applied typical uniform mesh refinement by hand. It would also allow for the simulation of larger objects since an optimal mesh is created.

Cwik, Tom↗
DOE OSTI2025

10-th order of accuracy for numerical solution of 3-D elasticity equations for heterogeneous materials on unfitted Cartesian meshes

We have developed the Optimal Local Truncation Error Method (OLTEM) with 10-th order of accuracy on unfitted Cartesian meshes for a system of 3-D elasticity equations with smooth irregular interfaces. 5 x 5 x 5 = 125-point stencils (similar to those for quadratic finite elements) for elastic heterogeneous materials are used for OLTEM. There are no unknowns at the interface points between different materials; the structure of the global discrete equations is the same for homogeneous and heterogeneous materials. The calculation of unknown stencil coefficients is based on the minimization of the local truncation error of the stencil equations and yields the optimal 10-th order of accuracy for OLTEM on unfitted Cartesian meshes, i.e., the increase by 7 orders in accuracy compared to quadratic finite elements on conformal meshes. A new post-processing procedure provides the 9-th order of accuracy for stresses in the 3-D case. Similar to basic computations it uses OLTEM with the 125-point stencils, the interface conditions and the elasticity equations. It was shown that the use of the elasticity equations for post-processing improves the accuracy of 0.1% stresses by 6 orders compared to post-processing without the use of PDEs. At an accuracy of for stresses, OLTEM with the new post-processing procedure reduces the number of degrees of freedom by 360 - 8000 times compared to quadratic finite elements with similar stencils. OLTEM with the 125-point stencils yields even more accurate results than high-order finite elements with much wider stencils. OLTEM provides accurate numerical results for compressible and nearly incompressible materials.

elasticity equations↗
NASA NTRS2018

NASA Additive Manufacturing Initiatives for Deep Space Human Exploration

Additive Manufacturing (AM) is being infused into aerospace industries at an accelerated pace. Reasons for this rapid adoption include: (1) Innovation Capability e.g. design features such as topology optimization, integrated fluid passages, and mesh structures; (2) Rapid Development and Optimization - ability to quickly iterate the design, development, and test cycle; (3) Affordability - reductions in part counts, cost, and schedule. NASA's Marshall Space Flight Center (MSFC) has taken a leadership role in application of AM technologies for deep space human exploration, leading the Agency's In Space Manufacturing (ISM) initiative and the application of AM for a broad variety of space propulsion systems. MSFC has championed the development of ISM capabilities since our first reduced-gravity aircraft experiment flew in 1999. Partnering with Made In Space, MSFC placed the first 3D Printer on ISS in 2014 and the second generation printer, the Additive Manufacturing Facility, in 2016. The next ISS technology demonstration will be the Refabricator, a recycler/basic printer scheduled to launch in late Fall 2018. Ground-based development is progressing in common use materials, metals 3D printing, printed electronics, and the new cornerstone of ISM, the FabLab. The latest developments in each area will be described. An overview of NASA's In Space Robotic Manufacturing and Assembly (IRMA) ground-based risk reduction projects will also be presented. MSFC has aggressively incorporated AM capabilities for design and development of space propulsion components. The capabilities have been rapidly matured and extensively exercised to produce and hot-fire test the Additive Manufacturing Demonstrator Engine, an in-space class prototype engine. This experience base has been extended to support Aerojet Rocketdyne in the application of AM to the RS-25, the Space Launch System Core Stage engine, and to small propulsion systems and thrusters for small satellites and cubesats. The latest developments will be described. In responding to a request from NASA's Commercial Crew Program for a consistent methodology for evaluation of AM processes and parts, MSFC began development of a draft standard for AM space flight hardware in late 2014. The draft was broadly disseminated for comments in mid-2015, and subsequently revised into two documents, a standard and a specification for AM space flight hardware, which were formally released by MSFC in October 2017. An overview of the key elements of these documents will be presented.

Clinton, Raymond↗
NASA NTRSDate not supplied

Optimization of Plug Nozzles Using CFD Informed Design Space Querying

This paper presents an axisymmetric CFD approach based on Reynolds-averaged Navier-Stokes (RANS) calculations for the shape optimization of plug nozzle contours for both supersonic cruise and landing/takeoff (LTO) conditions. Three key external plug design parameters were defined as independent variables in the optimization scheme, while nozzle performance was evaluated using thrust coefficient (Cfg) and discharge coefficient (Cd) as the primary dependent variables. By varying these parameters, a wide range of axisymmetric conic section plug profiles can be achieved, simplifying the problem. The paper also discusses the supersonic plug nozzle optimization approach, design space seeding, meshing, and CFD simulations for the optimization process. The results demonstrate that the approach is effective in exploring the parameter space and reducing computational expenses, making it a viable option for optimizing nozzle plug contours. Using this optimization toolchain, the study yielded preliminary designs for LTO, cruise, and LTO-cruise balanced plug nozzles.

nozzles↗
NASA NTRSDate not supplied

Optimization of Plug Nozzles Using CFD Informed Design Space Querying

This paper presents an axisymmetric CFD approach based on Reynolds-averaged Navier-Stokes (RANS) calculations for the shape optimization of plug nozzle contours for both supersonic cruise and landing/takeoff (LTO) conditions. Three key external plug design parameters were defined as independent variables in the optimization scheme, while nozzle performance was evaluated using thrust coefficient (Cfg) and discharge coefficient (Cd) as the primary dependent variables. By varying these parameters, a wide range of axisymmetric conic section plug profiles can be achieved, simplifying the problem. The paper also discusses the supersonic plug nozzle optimization approach, design space seeding, meshing, and CFD simulations for the optimization process. The results demonstrate that the approach is effective in exploring the parameter space and reducing computational expenses, making it a viable option for optimizing nozzle plug contours. Using this optimization toolchain, the study yielded preliminary designs for LTO, cruise, and LTO-cruise balanced plug nozzles.

CFD↗
NASA NTRS1996

Quantification of Gear Tooth Damage by Optimal Tracking of Vibration Signatures

This paper presents a technique for quantifying the wear or damage of gear teeth in a transmission system. The procedure developed in this study can be applied as a part of either an onboard machine health-monitoring system or a health diagnostic system used during regular maintenance. As the developed methodology is based on analysis of gearbox vibration under normal operating conditions, no shutdown or special modification of operating parameters is required during the diagnostic process. The process of quantifying the wear or damage of gear teeth requires a set of measured vibration data and a model of the gear mesh dynamics. An optimization problem is formulated to determine the profile of a time-varying mesh stiffness parameter for which the model output approximates the measured data. The resulting stiffness profile is then related to the level of gear tooth wear or damage. The procedure was applied to a data set generated artificially and to another obtained experimentally from a spiral bevel gear test rig. The results demonstrate the utility of the procedure as part of an overall health-monitoring system.

Choy, F. K.↗