Results for “Mesh optimization” — Page 2

NASA NTRS2019

Adjoint-Based Mesh Adaptation and Shape Optimization for Simulations with Propulsion

Objectives: Reliable evaluation of mass flow rates through permeable boundaries - Estimate and control discretization error- Consider both computational domain outflow and inflow- Applicable to simulating propulsion-system effects, as well as secondary flow paths - Explore feasibility of handling more general outputs at domain boundaries. Design optimization subject to mass-flow-rate constraints - Improve aerodynamic performance and reduce noise due to sonic boom - Control discretization error in design space to improve confidence in final designs.

Nemec, Marian↗

NASA NTRS2014

802.11s Wireless Mesh Network Visualization Application

Results of past experimentation at NASA Johnson Space Center showed that the IEEE 802.11s standard has better performance than the widely implemented alternative protocol B.A.T.M.A.N (Better Approach to Mobile Ad hoc Networking). 802.11s is now formally incorporated into the Wi- Fi 802.11-2012 standard, which specifies a hybrid wireless mesh networking protocol (HWMP). In order to quickly analyze changes to the routing algorithm and to support optimizing the mesh network behavior for our intended application a visualization tool was developed by modifying and integrating open source tools.

Mauldin, James Alexander↗

NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation high-lift 2D airfoil↗

NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation↗

NASA NTRS1987

Constrained sheath optics for high thrust density, low specific impulse ion thrusters

The results of an experimental study showing that a contoured, fine wire mesh attached to the screen grid can be used to control the divergence characteristics of ion beamlets produced at low net-to-total accelerating voltage ratios are presented. The influence of free and constrained-sheath optics systems on beamlet divergence characteristics are found to be similar in the operating regime investigated, but it was found that constrained-sheath optics systems can be operated at higher perveance levels than free-sheath ones. The concept of a fine wire interference probe that can be used to study ion beamlet focusing behavior is introduced. This probe is used to demonstrate beamlet focusing to a diameter about one hundreth of the screen grid extraction aperture diameter. Additional testing is suggested to define an optimally contoured mesh that could yield well focused beamlets at net-to-total accelerating voltage ratios below about 0.1.

Wilbur, Paul J.↗

NASA NTRS1993

Three-dimensional unstructured grid refinement and optimization using edge-swapping

This paper presents a three-dimensional (3-D) 'edge-swapping method based on local transformations. This method extends Lawson's edge-swapping algorithm into 3-D. The 3-D edge-swapping algorithm is employed for the purpose of refining and optimizing unstructured meshes according to arbitrary mesh-quality measures. Several criteria including Delaunay triangulations are examined. Extensions from two to three dimensions of several known properties of Delaunay triangulations are also discussed.

Gandhi, Amar↗

NASA NTRS2013

Output Error Estimates and Mesh Refinement in Aerodynamic Shape Optimization

No abstract available

Nemec, Marian↗

NASA NTRS1997

Error Estimation and h-Adaptivity for Optimal Finite Element Analysis

The objective of adaptive meshing and automatic error control in finite element analysis is to eliminate the need for the application engineer from re-meshing and re-running design simulations to verify numerical accuracy. The user should only need to enter the component geometry and a coarse finite element mesh. The software will then autonomously and adaptively refine this mesh where needed, reducing the error in the fields to a user prescribed value. The ideal end result of the simulation is a measurable quantity (e.g. scattered field, input impedance), calculated to a prescribed error, in less time and less machine memory than if the user applied typical uniform mesh refinement by hand. It would also allow for the simulation of larger objects since an optimal mesh is created.

Cwik, Tom↗

NASA NTRS2018

NASA Additive Manufacturing Initiatives for Deep Space Human Exploration

Additive Manufacturing (AM) is being infused into aerospace industries at an accelerated pace. Reasons for this rapid adoption include: (1) Innovation Capability e.g. design features such as topology optimization, integrated fluid passages, and mesh structures; (2) Rapid Development and Optimization - ability to quickly iterate the design, development, and test cycle; (3) Affordability - reductions in part counts, cost, and schedule. NASA's Marshall Space Flight Center (MSFC) has taken a leadership role in application of AM technologies for deep space human exploration, leading the Agency's In Space Manufacturing (ISM) initiative and the application of AM for a broad variety of space propulsion systems. MSFC has championed the development of ISM capabilities since our first reduced-gravity aircraft experiment flew in 1999. Partnering with Made In Space, MSFC placed the first 3D Printer on ISS in 2014 and the second generation printer, the Additive Manufacturing Facility, in 2016. The next ISS technology demonstration will be the Refabricator, a recycler/basic printer scheduled to launch in late Fall 2018. Ground-based development is progressing in common use materials, metals 3D printing, printed electronics, and the new cornerstone of ISM, the FabLab. The latest developments in each area will be described. An overview of NASA's In Space Robotic Manufacturing and Assembly (IRMA) ground-based risk reduction projects will also be presented. MSFC has aggressively incorporated AM capabilities for design and development of space propulsion components. The capabilities have been rapidly matured and extensively exercised to produce and hot-fire test the Additive Manufacturing Demonstrator Engine, an in-space class prototype engine. This experience base has been extended to support Aerojet Rocketdyne in the application of AM to the RS-25, the Space Launch System Core Stage engine, and to small propulsion systems and thrusters for small satellites and cubesats. The latest developments will be described. In responding to a request from NASA's Commercial Crew Program for a consistent methodology for evaluation of AM processes and parts, MSFC began development of a draft standard for AM space flight hardware in late 2014. The draft was broadly disseminated for comments in mid-2015, and subsequently revised into two documents, a standard and a specification for AM space flight hardware, which were formally released by MSFC in October 2017. An overview of the key elements of these documents will be presented.

Clinton, Raymond↗

NASA NTRSDate not supplied

Optimization of Plug Nozzles Using CFD Informed Design Space Querying

This paper presents an axisymmetric CFD approach based on Reynolds-averaged Navier-Stokes (RANS) calculations for the shape optimization of plug nozzle contours for both supersonic cruise and landing/takeoff (LTO) conditions. Three key external plug design parameters were defined as independent variables in the optimization scheme, while nozzle performance was evaluated using thrust coefficient (Cfg) and discharge coefficient (Cd) as the primary dependent variables. By varying these parameters, a wide range of axisymmetric conic section plug profiles can be achieved, simplifying the problem. The paper also discusses the supersonic plug nozzle optimization approach, design space seeding, meshing, and CFD simulations for the optimization process. The results demonstrate that the approach is effective in exploring the parameter space and reducing computational expenses, making it a viable option for optimizing nozzle plug contours. Using this optimization toolchain, the study yielded preliminary designs for LTO, cruise, and LTO-cruise balanced plug nozzles.

nozzles↗

NASA NTRSDate not supplied

Optimization of Plug Nozzles Using CFD Informed Design Space Querying

This paper presents an axisymmetric CFD approach based on Reynolds-averaged Navier-Stokes (RANS) calculations for the shape optimization of plug nozzle contours for both supersonic cruise and landing/takeoff (LTO) conditions. Three key external plug design parameters were defined as independent variables in the optimization scheme, while nozzle performance was evaluated using thrust coefficient (Cfg) and discharge coefficient (Cd) as the primary dependent variables. By varying these parameters, a wide range of axisymmetric conic section plug profiles can be achieved, simplifying the problem. The paper also discusses the supersonic plug nozzle optimization approach, design space seeding, meshing, and CFD simulations for the optimization process. The results demonstrate that the approach is effective in exploring the parameter space and reducing computational expenses, making it a viable option for optimizing nozzle plug contours. Using this optimization toolchain, the study yielded preliminary designs for LTO, cruise, and LTO-cruise balanced plug nozzles.

CFD↗

NASA NTRS1996

Quantification of Gear Tooth Damage by Optimal Tracking of Vibration Signatures

This paper presents a technique for quantifying the wear or damage of gear teeth in a transmission system. The procedure developed in this study can be applied as a part of either an onboard machine health-monitoring system or a health diagnostic system used during regular maintenance. As the developed methodology is based on analysis of gearbox vibration under normal operating conditions, no shutdown or special modification of operating parameters is required during the diagnostic process. The process of quantifying the wear or damage of gear teeth requires a set of measured vibration data and a model of the gear mesh dynamics. An optimization problem is formulated to determine the profile of a time-varying mesh stiffness parameter for which the model output approximates the measured data. The resulting stiffness profile is then related to the level of gear tooth wear or damage. The procedure was applied to a data set generated artificially and to another obtained experimentally from a spiral bevel gear test rig. The results demonstrate the utility of the procedure as part of an overall health-monitoring system.

Choy, F. K.↗

NASA NTRS2018

Design of a Modular Monolithic Implicit Solver for Multi-Physics Applications

The design of a modular multi-physics high-order space-time finite-element framework is presented together with its extension to allow monolithic coupling of different physics. One of the main objectives of the framework is to perform efficient high- fidelity simulations of capsule/parachute systems. This problem requires simulating multiple physics including, but not limited to, the compressible Navier-Stokes equations, the dynamics of a moving body with mesh deformations and adaptation, the linear shell equations, non-re effective boundary conditions and wall modeling. The solver is based on high-order space-time - finite element methods. Continuous, discontinuous and C1-discontinuous Galerkin methods are implemented, allowing one to discretize various physical models. Tangent and adjoint sensitivity analysis are also targeted in order to conduct gradient-based optimization, error estimation, mesh adaptation, and flow control, adding another layer of complexity to the framework. The decisions made to tackle these challenges are presented. The discussion focuses first on the "single-physics" solver and later on its extension to the monolithic coupling of different physics. The implementation of different physics modules, relevant to the capsule/parachute system, are also presented. Finally, examples of coupled computations are presented, paving the way to the simulation of the full capsule/parachute system.

Carton De Wiart, Corentin↗

NASA NTRS1991

Local Synthesis and Tooth Contact Analysis of Face-Milled Spiral Bevel Gears

Computerized simulation of meshing and bearing contact for spiral bevel gears and hypoid gears is a significant achievement that could substantially improve the technology and the quality of the gears. An approach to the synthesis of face-milled spiral bevel gears and their tooth contact analysis is presented. The proposed approach is based on the following ideas: application of the principle of local synthesis that provides optimal conditions of meshing and contact at the mean contact point, M, and in the neighborhood of M; and application of relations between principle directions and curvatures for surfaces being in line contact or in point contact. The developed local synthesis of gears provides the following: (1) the required gear ratio at M; (2) a localized bearing contact with the desired direction of the tangent to the contact path on gear tooth surface and the desired length of the major axis of contact ellipse at M; (3) a predesigned parabolic function of a controlled level for transmission errors which enables absorption of linear functions of transmission errors caused by misalignment and reduces the level of vibrations. The proposed approach does not require either the tilt of the head-cutter for the process of generation or modified roll for the pinion generation. Improved conditions of meshing and contact of the gears can be achieved without the above mentioned parameters. A computer program for determination of basic machine-tool settings and tooth contact analysis for the designed gears is presented. The approach is illustrated with a numerical example.

Litvin, Faydor L.↗

NASA NTRS1990

Shape design sensitivities using fully automatic 3-D mesh generation

Previous work in three dimensional shape optimization involved specifying design variables by associating parameters directly with mesh points. More recent work has shown the use of fully-automatic mesh generation based upon a parameterized geometric representation. Design variables have been associated with a mathematical model of the part rather than the discretized representation. The mesh generation procedure uses a nonuniform grid intersection technique to place nodal points directly on the surface geometry. Although there exists an associativity between the mesh and the geometrical/topological entities, there is no mathematical functional relationship. This poses a problem during certain steps in the optimization process in which geometry modification is required. For the large geometrical changes which occur at the beginning of each optimization step, a completely new mesh is created. However, for gradient calculations many small changes must be made and it would be too costly to regenerate the mesh for each design variable perturbation. For that reason, a local remeshing procedure has been implemented which operates only on the specific edges and faces associated with the design variable being perturbed. Two realistic design problems are presented which show the efficiency of this process and test the accuracy of the gradient computations.

Botkin, M. E.↗

NASA NTRS2021

A Study into Validating a Coupled Method of Characteristics and Direct Simulation Monte Carlo Method Against Empirical Data

The following will outline the methodology and results of validating a coupled Method of Characteristics (MOC) and Direct Simulation Monte Carlo (DSMC) method. This research focused specifically on modeling plume impingement, induced by Reaction Control System (RCS) thrusters that flew on the National Aeronautics and Space Administration’s (NASA’s) space shuttle Discovery. For each simulation, the continuum portion of the RCS thruster was simulated using MOC for solving hyperbolic Partial Differential Equations (PDEs) and computed with the NASA code, Reacting and Multi-phase Program (RAMP). The solution was then implemented as a starting condition into the NASA DSMC code, Direct Simulation and Monte Carlo Analysis Code (DAC). Typically, DSMC models rely on code-to-code validation for fidelity. The significance of this research is in its ability to validate its models against empirical data. Prior to computing solutions for these simulations, the mesh size and structure were optimized and many variants of DSMC input parameters were iterated on in order to acquire a reliable, mesh-independent, fully optimized numerical solution. This research will discuss the mathematical formulation of MOC for nozzle flow and DSMC for rarefied gases. Additionally, it will provide an explanation of how to implement these mathematical concepts into the two solvers: RAMP and DAC. Ultimately, this research will demonstrate that the overall process illustrated produces results in good agreement with empirical data. As a consequence, the methodology presented is granted an increased level of confidence and will greatly contribute to the aerospace industry and its effort in understanding and predicting rarefied flow fields.

Direct Simulation Monte Carlo Analysis Code↗

NASA NTRS2021

A Study into Validating A Coupled Method of Characteristics And Direct Simulation Monte Carlo Method Against Empirical Data

The following will outline the methodology and results of validating a coupled Method of Characteristics (MOC) and Direct Simulation Monte Carlo (DSMC) method. This research focused specifically on modeling plume impingement, induced by Reaction Control System (RCS) thrusters that flew on the National Aeronautics and Space Administration’s (NASA’s) space shuttle Discovery. For each simulation, the continuum portion of the RCS thruster was simulated using MOC for solving hyperbolic Partial Differential Equations (PDEs) and computed with the NASA code, Reacting and Multi-phase Program (RAMP). The solution was then implemented as a starting condition into the NASA DSMC code, Direct Simulation and Monte Carlo Analysis Code (DAC). Typically, DSMC models rely on code-to-code validation for fidelity. The significance of this research is in its ability to validate its models against empirical data. Prior to computing solutions for these simulations, the mesh size and structure were optimized and many variants of DSMC input parameters were iterated on in order to acquire a reliable, mesh-independent, fully optimized numerical solution. This research will discuss the mathematical formulation of MOC for nozzle flow and DSMC for rarefied gases. Additionally, it will provide an explanation of how to implement these mathematical concepts into the two solvers: RAMP and DAC. Ultimately, this research will demonstrate that the overall process illustrated produces results in good agreement with empirical data. As a consequence, the methodology presented is granted an increased level of confidence and will greatly contribute to the aerospace industry and its effort in understanding and predicting rarefied flow fields.

DAC↗

NASA NTRSDate not supplied

Overlap Preservation Using Loosely-Coupled Boundary Conditions for Body-Fitted Structured Overset Grids

Several improvements are made to overlap preservation in the automated approach to generating overset structured meshes. A loosely-coupled boundary condition (LCBC) is introduced to maintain optimal overlap for surface meshes generated from overlapping initial curves. Extension of the LCBC scheme to three-dimensional volume meshing is also presented. Test cases include various rotary wing vehicles from NASA’s Revolutionary Vertical Lift Technology (RVLT) project, and the wing-body geometry from the NASA Juncture Flow Experiment. Results demonstrate improvements in donor stencil quality from the enhanced overlap between neighboring surface and volume meshes.

TTT↗