Search NASA⌕ Search

SEARCH · Search NASA

Results for “Michael Addition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

The Crucial Role of Error Correlation for Uncertainty Modeling of CFD-Based Aerodynamics Increments

The Ares I ascent aerodynamics database for Design Cycle 3 (DAC-3) was built from wind-tunnel test results and CFD solutions. The wind tunnel results were used to build the baseline response surfaces for wind-tunnel Reynolds numbers at power-off conditions. The CFD solutions were used to build increments to account for Reynolds number effects. We calculate the validation errors for the primary CFD code results at wind tunnel Reynolds number power-off conditions and would like to be able to use those errors to predict the validation errors for the CFD increments. However, the validation errors are large compared to the increments. We suggest a way forward that is consistent with common practice in wind tunnel testing which is to assume that systematic errors in the measurement process and/or the environment will subtract out when increments are calculated, thus making increments more reliable with smaller uncertainty than absolute values of the aerodynamic coefficients. A similar practice has arisen for the use of CFD to generate aerodynamic database increments. The basis of this practice is the assumption of strong correlation of the systematic errors inherent in each of the results used to generate an increment. The assumption of strong correlation is the inferential link between the observed validation uncertainties at wind-tunnel Reynolds numbers and the uncertainties to be predicted for flight. In this paper, we suggest a way to estimate the correlation coefficient and demonstrate the approach using code-to-code differences that were obtained for quality control purposes during the Ares I CFD campaign. Finally, since we can expect the increments to be relatively small compared to the baseline response surface and to be typically of the order of the baseline uncertainty, we find that it is necessary to be able to show that the correlation coefficients are close to unity to avoid overinflating the overall database uncertainty with the addition of the increments.

Hemsch, Michael J.↗
NASA NTRS2020

TPSAS-NF1676L-35475-DND

This project would identify a methodology and implement a living solution to map, both visually and utilizing some form of database, the complex network of stakeholders that the Disasters Program routinely interacts with to maximize efficiency and minimize confusion and overlapping effort during disaster responses. This project's solution will take into account factors such as stakeholder data production type, geospatial data maturity, geographic areas of interest, federal mandates, type of relationship, national priorities and many additional relevant attributes.

Lauren Cutler↗
NASA NTRS1999

STS-103 Flight Day 5 Highlights and Crew Activities Report

Highlights of the fifth day of the STS-103 mission on board the space shuttle Discovery are shown in this videotape. The mission was led by Commander Curtis L. Brown, with Pilot Scott J Kelly, and Mission Specialists Steven L. Smith, Jean-Francois Clervoy, John M. Grunsfeld, Michael Foale, and Claude Nicollier. The main purpose of the mission was to service the Hubble Space Telescope (HST). The primary objective of the mission was to replace all six of the gyroscopes that make up the three Rate Sensor Units. In addition the Astronauts installed a new computer. During the 5th day Michael Foale and Claude Nicollier performed the servicing of the HST in an 8 hour 10 minute Extravehicular Activity (EVA). The servicing included the removal of the old computer and the installation of a new, faster computer with more memory. They also installed a new outer thermal layer to protect the computer. After this was finished the astronauts replaced one of the Fine Guidance Sensors (FGS), an optical sensor which allows NASA to point the telescope in the desired direction. The video includes actual live views of the HST in the shuttle's service bay, and footage of the repair and servicing EVA.

Source record↗
NASA NTRSDate not supplied

Assured Performance of Additively Manufactured and Composite Parts through Embedded Sensing and Life Cycle Monitoring: An Enabler for in-Space Use

Lightweight composites have a range of applications in aerospace where operational costs and mission (payload) capabilities depend significantly on component weight. Additive manufacturing of the composite components expands the design and production space allowing for complex part geometries. A limiting factor to the utilization of the composites in high value applications, such as aerospace generally, and particularly for in-space applications, is the ability to determine the part quality both at the time of production as well as through the lifetime of the component. Work on monitoring the performance of additively manufactured and autoclaved composites that encompasses the design and manufacturing as well as use in operational environments will be discussed. Optimization of the component design for manufacturability, the use of process monitoring sensors during the component build as well as embedding of carbon nanotube yarn based structural sensors will be described.

Additive Manufacturing↗
NASA NTRS1985

Transonic rotor tip design using numerical optimization

The aerodynamic design procedure for a new blade tip suitable for operation at transonic speeds is illustrated. For the first time, 3 dimensional numerical optimization was applied to rotor tip design, using the recent derivative of the ROT22 code, program R22OPT. Program R22OPT utilized an efficient quasi-Newton optimization algorithm. Multiple design objectives were specified. The delocalization of the shock wave was to be eliminated in forward flight for an advance ratio of 0.41 and a tip Mach number of 0.92 at psi = 90 deg. Simultaneously, it was sought to reduce torque requirements while maintaining effective restoring pitching moments. Only the outer 10 percent of the blade span was modified; the blade area was not to be reduced by more than 3 percent. The goal was to combine the advantages of both sweptback and sweptforward blade tips. A planform that featured inboard sweepback was combined with a sweptforward tip and a taper ratio of 0.5. Initially, the ROT22 code was used to find by trial and error a planform geometry which met the design goals. This configuration had an inboard section with a leading edge sweep of 20 deg and a tip section swept forward at 25 deg; in addition, the airfoils were modified.

Tauber, Michael E.↗
NASA NTRS1998

Computational Chemistry and Lubrication

Members of NASA Lewis Research Center's Tribology and Surface Science Branch are applying high-level computational chemistry techniques to the development of new lubrication systems for space applications and for future advanced aircraft engines. The next generation of gas turbine engines will require a liquid lubricant to function at temperatures in excess of 350 C in oxidizing environments. Conventional hydrocarbon-based lubricants are incapable of operating in these extreme environments, but a class of compounds known as the perfluoropolyether (PFAE) liquids (see the preceding illustration) shows promise for such applications. These commercially available products are already being used as lubricants in conditions where low vapor pressure and chemical stability are crucial, such as in satellite bearings and composite disk platters. At higher temperatures, however, these compounds undergo a decomposition process that is assisted (catalyzed) by metal and metal oxide bearing surfaces. This decomposition process severely limits the applicability of PFAE's at higher temperatures. A great deal of laboratory experimentation has revealed that the extent of fluid degradation depends on the chemical properties of the bearing surface materials. Lubrication engineers would like to understand the chemical breakdown mechanism to design a less vulnerable PFAE or to develop a chemical additive to block this degradation.

Zehe, Michael J.↗
NASA NTRS2010

Space Weather Products at the Community Coordinated Modeling Center

In addition to supporting space research in the international community, the Community Coordinated Modeling Center (CCMC) has as its second objective to bring to apply the power of modern research models toward space weather specification and forecasting. Initially motivated by the objective to test models and to ease the transition of research models to space weather forecasting organization, the CCMC has developed a number of real-time modeling systems, as well as large number of modeling and data products for space weather forecasting. Over time, these activities have evolved into tailored products for partners, as well as into a direct support of the space weather needs within NASA robotic mission community. Accessible through a customizable interface, users within the US or at partnering institutions internationally have access to space weather tools driven by the most advanced space research models. Through partnering with agencies and institutions in the US and abroad, the CCMC strives to set up further data sharing agreements to the benefit of all participating institutions. In this presentation, we provide an overview of existing CCMC space weather services and products, and we will explore additional avenues for international collaborations.

Hesse, Michael↗
NASA NTRS2011

Emission Spectroscopic Measurements with an Optical Probe in the NASA Ames IHF Arc Jet Facility

An optical probe was designed to measure radiation (from inside the arc heater) incident on a test sample immersed in the arc-heated stream. Currently, only crude estimates are available for this incident radiation. Unlike efforts of the past, where the probe line of sight was inclined to the nozzle centerline, the present development focuses on having the probe line of sight coincide with the nozzle centerline. A fiber-coupled spectrometer was used to measure the spectral distribution of incident radiation in the wavelength range of 225 to 900 nm. The radiation heat flux in this wavelength range was determined by integration of measured emission spectral intensity calibrated to incident irradiance from an integrating sphere. Two arc-heater conditions, corresponding to stream bulk enthalpy levels of 12 and 22 MJ/kg, were investigated in the 13-inch diameter nozzle of the Interaction Heating Facility at NASA Ames Research Center. With the probe placed at a distance of 10 inches from the nozzle exit plane, total radiative heat fluxes were measured to be 3.3 and 8.4 W/sq cm for the 12 and 22 MJ/kg conditions, respectively. About 17% of these radiative fluxes were due to bound-bound radiation from atoms and molecules, while the remaining 83% could be attributed to continua (bound-free and/or free-free). A comparison with spectral simulation based on CFD solutions for the arc-heater flow field and with spectroscopic measurements in the plenum region indicates that more than 95% of the measured radiation is generated in the arc region. The total radiative heat flux from the line radiation could increase by a factor of two through contributions from wavelengths outside the measured range, i.e., from the vacuum ultraviolet (wavelengths less than 225 nm) and the infrared (wavelengths greater than 900 nm). An extrapolation of the continuum radiation to these two wavelength regions was not attempted. In the tested configuration, the measured radiative heat flux accounts for only about 1.4% of the nominal heat flux on a flat face model and therefore is considered negligible. In the 6-inch diameter nozzle, on account of shorter path lengths, the radiation heat flux could be significant. Therefore, future tests in the 6-inch nozzle will have radiometers in addition to the optical probe.

Winter, Michael↗
NASA NTRS2014

Deducing Electronic Unit Internal Response During a Vibration Test Using a Lumped Parameter Modeling Approach

During random vibration testing of electronic boxes there is often a desire to know the dynamic response of certain internal printed wiring boards (PWBs) for the purpose of monitoring the response of sensitive hardware or for post-test forensic analysis in support of anomaly investigation. Due to restrictions on internally mounted accelerometers for most flight hardware there is usually no means to empirically observe the internal dynamics of the unit, so one must resort to crude and highly uncertain approximations. One common practice is to apply Miles Equation, which does not account for the coupled response of the board in the chassis, resulting in significant over- or under-prediction. This paper explores the application of simple multiple-degree-of-freedom lumped parameter modeling to predict the coupled random vibration response of the PWBs in their fundamental modes of vibration. A simple tool using this approach could be used during or following a random vibration test to interpret vibration test data from a single external chassis measurement to deduce internal board dynamics by means of a rapid correlation analysis. Such a tool might also be useful in early design stages as a supplemental analysis to a more detailed finite element analysis to quickly prototype and analyze the dynamics of various design iterations. After developing the theoretical basis, a lumped parameter modeling approach is applied to an electronic unit for which both external and internal test vibration response measurements are available for direct comparison. Reasonable correlation of the results demonstrates the potential viability of such an approach. Further development of the preliminary approach presented in this paper will involve correlation with detailed finite element models and additional relevant test data.

random vibration response↗
NASA NTRS2019

Additive Manufacturing of Multi-Material Systems for Aerospace Applications

Additive manufacturing methods for producing single materials are rapidly improving. The resulting material properties and microstructures are becoming more comparable to those of conventionally fabricated materials. However, the need for multi-functional and complex structures and components requires additional innovations in manufacturing such as multi-material and hybrid additive manufacturing approaches. Additive manufacturing machines with multiple print capabilities and combinations of AM, machining, and conventional processing methods will further open up design spaces and possibilities. In this presentation, several examples of the needs and methods for multi-material fabrication will be discussed with a focus on aerospace applications. Direct printing of silver coils in conjunction with fused deposition modeling, machined parts, and, binder jetting is being developed for innovative stator designs. Binder jetting of silicon-based materials with powder bed additions is being developed for heat exchanger applications. Additive manufacturing of bi-material systems is being pursued to fabricate lightweight, integrated, multifunctional structures.

multi-materials↗
NASA NTRS2020

An Over-the-Rotor Liner Investigation with Configurations Enabled by Additive Manufacturing

This paper presents the results of an investigation of over-the-rotor acoustic liner configurations enabled by additive manufacturing. NASA Langley and Glenn Research Centers have collaborated on the usage of acoustic liners in the turbofan aircraft engine nacelle wall at or very near the tip of the rotor. These liners absorb rotor-alone and rotor-stator interaction noise and, due to their proximity to the rotor tips, serve as a pressure release to inhibit the amount of generated noise. Initial tests with a metallic foam liner demonstrated good acoustic results, but there was concern regarding the durability of the material. NASA then decided to explore configurations enabled by additive manufacturing via tests in the NASA Langley Normal Incidence Tube. Measured data for uniform-depth and variable-depth cores with narrow and wide chambers were compared with predictions via the NASA Langley impedance prediction model. As these configurations were intended for eventual use in an over-the-rotor application, it was necessary to add facesheets to the wide-chamber cores to avoid deleterious flow effects caused by open cavities. A number of facesheets were tested in combination with each wide-chamber core. Finally, it has been shown that grooves near the rotor tips cause an improvement in aerodynamic performance. A small set of grooves were fabricated such that they could be combined with the wide-chamber configurations. The results of these tests were subsequently used to guide designs for further testing in higher technology readiness level test rigs at NASA Glenn Research Center.

acoustic↗
NASA NTRS2015

Material Characterization of Additively Manufactured Components for Rocket Propulsion

To advance Additive Manufacturing (AM) technologies for production of rocket propulsion components the NASA Glenn Research Center (GRC) is applying state of the art characterization techniques to interrogate microstructure and mechanical properties of AM materials and components at various steps in their processing. The materials being investigated for upper stage rocket engines include titanium, copper, and nickel alloys. Additive manufacturing processes include laser powder bed, electron beam powder bed, and electron beam wire fed processes. Various post build thermal treatments, including Hot Isostatic Pressure (HIP), have been studied to understand their influence on microstructure, mechanical properties, and build density. Micro-computed tomography, electron microscopy, and mechanical testing in relevant temperature environments has been performed to develop relationships between build quality, microstructure, and mechanical performance at temperature. A summary of GRCs Additive Manufacturing roles and experimental findings will be presented.

Additive Manufacturing↗
NASA NTRS2015

Materials Characterization of Additively Manufactured Components for Rocket Propulsion

To advance Additive Manufacturing (AM) technologies for production of rocket propulsion components the NASA Glenn Research Center (GRC) is applying state of the art characterization techniques to interrogate microstructure and mechanical properties of AM materials and components at various steps in their processing. The materials being investigated for upper stage rocket engines include titanium, copper, and nickel alloys. Additive manufacturing processes include laser powder bed, electron beam powder bed, and electron beam wire fed processes. Various post build thermal treatments, including Hot Isostatic Pressure (HIP), have been studied to understand their influence on microstructure, mechanical properties, and build density. Micro-computed tomography, electron microscopy, and mechanical testing in relevant temperature environments has been performed to develop relationships between build quality, microstructure, and mechanical performance at temperature. A summary of GRC's Additive Manufacturing roles and experimental findings will be presented.

Additive Manufacturing↗
NASA NTRS2016

Additive Manufacturing of Silicon Carbide-Based Ceramic Matrix Composites: Technical Challenges and Opportunities

Advanced SiC-based ceramic matrix composites offer significant contributions toward reducing fuel burn and emissions by enabling high overall pressure ratio (OPR) of gas turbine engines and reducing or eliminating cooling air in the hot-section components, such as shrouds, combustor liners, vanes, and blades. Additive manufacturing (AM), which allows high value, custom designed parts layer by layer, has been demonstrated for metals and polymer matrix composites. However, there has been limited activity on additive manufacturing of ceramic matrix composites (CMCs). In this presentation, laminated object manufacturing (LOM), binder jet process, and 3-D printing approaches for developing ceramic composite materials are presented. For the laminated object manufacturing (LOM), fiber prepreg laminates were cut into shape with a laser and stacked to form the desired part followed by high temperature heat treatments. For the binder jet, processing optimization was pursued through silicon carbide powder blending, infiltration with and without SiC nano powder loading, and integration of fibers into the powder bed. Scanning electron microscopy was conducted along with XRD, TGA, and mechanical testing. Various technical challenges and opportunities for additive manufacturing of ceramics and CMCs will be presented.

ceramic matrix composites↗
NASA NTRS1987

AIS-2 spectra of California wetland vegetation

Spectral data gathered by Airborne Imaging Spectrometers-2 from wetlands were analyzed. Spectra representing stands of green Salicornia virginica, green Sesuvium verrucosum, senescing Distichlis spicata, a mixture of senescing Scirpus acutus and Scirpus californicus, senescing Scirpus paludosus, senescent S. paludosus, mowed senescent S. paludosus, and soil were isolated. No difference among narrowband spectral reflectance of the cover types was apparent between 0.8 to 1.6 micron. There were, however, broadband differences in brightness. These differences were sufficient to permit a fairly accurate decomposition of the image into its major cover type components using a procedure that assumes an additive linear mixture of surface spectra.

Gross, Michael F.↗
NASA NTRS1991

Space Station Freedom electric power system evolution analysis status

The ability is examined of the SSF baselined EPS to transition to operate at a greater system capacity beyond the SSF Permanent Manned Capability PMC) milestone. Specifically, a status of a current analysis is discussed concerning additions, modifications, changeout, or combination thereof of baseline EPS hardware and/or software needed to accomplish the power generation, distribution, operation, and use needed to meet evolving SSF mission objectives. This discussion results in several EPS architectural options that facilitate the addition or substitution of new technologies.

Zernic, Michael J.↗