Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mission Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Mission aware cyber safe mode for spacecraft

Mission-Aware Cyber Safe Mode (MACSM) is spacecraft resilience architecture that enables autonomous containment of software-level cyber intrusions while maintaining control authority and mission continuity. It is analogous to traditional safe modes that preserve vehicle survival by shutting down non-essential subsystems in response to faults or environmental stress.

97 MATHEMATICS AND COMPUTING↗

Demonstrating autonomous controls on hardware test beds is a necessity for successful missions to Mars and beyond

NASA and the Department of Defense are planning for a mission to Mars in the 2030s–2040s using nuclear thermal propulsion (NTP). NTP uses a nuclear reactor to heat flowing hydrogen and create thrust. A serious concern for crewed and uncrewed missions to Mars is the loss of reactor control. The reactor startup and initial rocket impulse are initiated in cislunar or near-earth orbital regions; therefore, radio communications between ground control and the NTP engine should occur in real time. However, radio communications can take more than 20 min, depending on planet positions, to reach Mars orbiters from ground control. To address this delay, local autonomous controls are implemented onboard the NTP engine to ensure acceptable operation. However, autonomous controls have not been demonstrated or implemented in research or power reactor contexts because of safety and reliability concerns. To enable autonomous controls development, demonstration, and validation, Oak Ridge National Laboratory has created a nonnuclear hardware-in-the-loop test bed. Sensors throughout the test bed relay system status and hardware response to the user control algorithm, including measurements of temperature, flow, pressure of a loop, control drum position, and drum speed. This paper discusses the development of this facility and user accessibility.

33 ADVANCED PROPULSION SYSTEMS↗

Resilient Control Systems Practical Metrics Basis for Defining Mission Impact

"Resilience” describes how systems operate at an acceptable level of normalcy despite disturbances or threats. In this paper we first consider the cognitive, cyber-physical interdependencies inherent in critical infrastructure systems and how resilience differs from reliability to mitigate these risks. Terminology and metrics basis are provided to integrate the cognitive, cyber-physical aspects that should be considered when defining solutions for resilience. A practical approach is taken to roll this metrics basis up to system integrity and business case metrics that establish “proper operation” and “impact.” A notional chemical processing plant is the use case for demonstrating how the system integrity metrics can be applied to establish performance, and

42 ENGINEERING↗

A thermal control system for long-term survival of scientific instruments on lunar surface

A thermal control system is being developed for scientific instruments placed on the lunar surface. This thermal control system, Lunar Mission Survival Module (MSM), was designed for scientific instruments that are planned to be operated for over a year in the future Japanese lunar landing mission SELENE-2. For the long-term operations, the lunar surface is a severe environment because the soil (regolith) temperature varies widely from nighttime −200 degC to daytime 100 degC approximately in which space electronics can hardly survive. The MSM has a tent of multi-layered insulators and performs a “regolith mound”. Temperature of internal devices is less variable just like in the lunar underground layers. The insulators retain heat in the regolith soil in the daylight, and it can keep the device warm in the night. We conducted the concept design of the lunar survival module, and estimated its potential by a thermal mathematical model on the assumption of using a lunar seismometer designed for SELENE-2. Thermal vacuum tests were also conducted by using a thermal evaluation model in order to estimate the validity of some thermal parameters assumed in the computed thermal model. The numerical and experimental results indicated a sufficient survivability potential of the concept of our thermal control system.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Combining RHF and HFIR Disposition Campaigns – Analysis, Opportunity, and Lessons Learned

Savannah River Nuclear Solutions has tasked its H-Canyon facility to prepare for disposition of used Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) cores. HFIR cores consist of an inner and outer assembly of highly enriched uranium fuel plates. The two elements are annular, nest inside each other, and the fuel form is a curved plate held between two collars. H-Canyon has a dissolver insert specifically designed for HFIR cores and has performed this type of campaign before between 1976 and 1988. At the H-Canyon facility, a dissolver is a large stainless steel pot loaded with a nitric acid solution into which uranium-alloy fuel is dissolved. The dissolver uses a device called an insert to feed the fuels to the acid solution in a controlled manner. The mission will be to dissolve a number of HFIR cores, purify the uranium, and down blend it to low enriched uranium suitable for commercial power reactors.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Combining RHF and HFIR Disposition Campaigns - Analysis, Opportunity, and Lessons Learned

Savannah River Nuclear Solutions has tasked its H Canyon facility to prepare for disposition of used Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) cores. HFIR cores consist of an inner and outer assembly of highly enriched uranium fuel plates. The two elements are annular, nest inside each other, and the fuel is a curved plate held between two collars. The H-Canyon facility has a dissolver insert specifically designed for HFIR cores and has performed this type of campaign before between 1976 and 1988. At H-Canyon, a dissolver is a large stainless steel pot loaded with a nitric acid solution into which uranium-alloy fuel is dissolved. The dissolver uses a device called an insert to feed the fuels to the acid solution in a controlled manner. The mission will be to dissolve a number of HFIR cores, purify the uranium, and down blend it to low enriched uranium suitable for commercial power reactors. HFIR has a sister core. A French high flux research reactor, called Reactor A Haut Flux (RHF), has nearly the same geometry as the outer element of HFIR. The annulus is only slightly smaller and the RHF active fuel height is {approx}97 cm while the HFIR active fuel height is only {approx}51 cm. SRNS is currently storing RHF cores (repatriated through circa 2003) awaiting a path for disposition. There is now an opportunity. RHF cores fit in the HFIR dissolver insert. Dispositioning them concurrent with HIFR avoids a future facility evolution of just to change dissolver inserts again. This work is the result of an initiative to propose appending the RHF cores to the anticipated HFIR campaign. Geometry and chemistry differences are evaluated and criticality safety assessed. The RHF cores were semi-explicitly modeled in various stages of dissolution. Normal and credible abnormal conditions were assessed. RHF was shown to be bounded by the dissolution of a complete HFIR core in both neutron multiplication and dissolver chemistry. Computational modeling was performed using KENOVI in the SCALE 6.1 code package.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Community-Controlled Transportation: The Western New York E-Bike Library Network: Preprint

Shared Mobility Inc. (SMI) has used their mission of community-controlled transportation to partner with community based organizations on the launch and operations of E-Bike Libraries (EBLs) in Western New York (WNY) and beyond since 2021. For almost four years, the WNY EBLs have provided e-bikes at no cost to underserved communities in Buffalo and Niagara Falls. Participants used the e-bikes for commuting, recreational rides, community bike rides, running errands, and accessing essential services. This program significantly increased e-bike accessibility, with 71% of participants being first-time riders and 78% identifying as Black/African American. Challenges such as bike maintenance, battery charging logistics, and the need for suitable storage were addressed through partnerships with community-based organizations and adjustments to program logistics. Those lessons have been applied to additional EBLs in Pacoima, California and Carlisle, Pennsylvania, which have also been launched by SMI with a continued emphasis on the importance of community based approaches to sustainable transportation. All of these programs demonstrate the potential of e-bikes to provide an affordable, efficient, and fun transportation option, particularly for underserved communities. By leveraging community partnerships and focusing on accessibility and inclusivity, E-Bike Libraries can significantly contribute to sustainable transportation solutions and promote broader participation in the transportation electrification revolution.

33 ADVANCED PROPULSION SYSTEMS↗

Approaches to integrating nuclear weapons stockpile management and arms control objectives.

Historically, U.S. arms control policy and the U.S. nuclear weapons enterprise have been reactive to each other, rather than interdependent and mutually reinforcing. One element of the divergence has been the long timescale necessary to plan and create substantive changes in the infrastructure vs. the inherent unpredictability of arms control outcomes. We explore several examples that illustrate this tension, some of the costs and implications associated with this reactive paradigm, and illustrate that, while the nuclear weapons enterprise has long considered the implications of arms control in sizing capacity of its missions, it has not substantively considered arms control in construction requirement for capabilities and products. Since previous arms control agreements have limited numbers and types of deployed systems, with delivery systems as the object of verification, this disconnect has not been forefront. However, as future agreements unfold, the warhead itself may become the treaty limited item and the object of verification. Such a scenario might offer both the need and the opportunity to integrate nuclear weapons and arms control requirements in unprecedented ways. This paper seeks to inspire new thinking on how such integration could be fostered and the extent to which it can facilitate significant reduction in nuclear stockpiles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

CDP - Adaptive Supervisory Control and Data Acquisition (SCADA) Technology for Infrastructure Protection (Final Report)

Supervisory Control and Data Acquisition (SCADA) Systems are a type of Industrial Control System characterized by the centralized (or hierarchical) monitoring and control of geographically dispersed assets. SCADA systems combine acquisition and network components to provide data gathering, transmission, and visualization for centralized monitoring and control. However these integrated capabilities, especially when built over legacy systems and protocols, generally result in vulnerabilities that can be exploited by attackers, with potentially disastrous consequences. Our research project proposal was to investigate new approaches for secure and survivable SCADA systems. In particular, we were interested in the resilience and adaptability of large-scale mission-critical monitoring and control infrastructures. Our research proposal was divided in two main tasks. The first task was centered on the design and investigation of algorithms for survivable SCADA systems and a prototype framework demonstration. The second task was centered on the characterization and demonstration of the proposed approach in illustrative scenarios (simulated or emulated).

97 MATHEMATICS AND COMPUTING↗

A Minimum Principle-Based Algorithm for Energy-Efficient Eco-Driving of Electric Vehicles in Various Traffic and Road Conditions

Our report presents an optimization algorithm for energy-efficient driving of electric vehicles. The algorithm is based on Pontryagin’s Minimum Principle by considering the driving mission as an optimal control problem. On a planned route, diverse application cases may occur due to various physical traits such as powertrain (e.g., switching between motor and generator operation), environmental variations (e.g., terrain grade change), traffic laws (e.g., speed limits), and safety concerns (e.g., headway to the leading vehicle). The proposed algorithm handles these real-world challenges by considering the perturbation to the system dynamics and the constraints to the control and state variables.

33 ADVANCED PROPULSION SYSTEMS↗

"Development and Commercialization of Alternative Carbon Precursors and Conversion Technologies" (CRADA Final Report)

The overall objective of the collaborative research performed by the Oak Ridge National Laboratory (ORNL) and the Dow Chemical Company under this Cooperative Research And Development Agreement (CRADA NFE-10-02991) was to develop and establish pathways to commercialize new carbon fiber precursor and conversion technology. This technology is to produce alternative polymer fiber precursor formulations as well as scaled energy-efficient advanced conversion technology to enable continuous mode conversion to obtain carbonized fibers that are technically and economically viable in industrial markets such as transportation, wind energy, infrastructure and oil drilling applications. There have been efforts in the past to produce a low cost carbon fiber. These attempts have to be interpreted against the backdrop of the market needs at the time, which were strictly military aircraft and high-end aerospace components. In fact, manufacturing costs have been reduced from those days to current practice, where both process optimization and volume production have enabled carbon fiber to become available at prices below $20/lb. However, the requirements of the lucrative aerospace market limits further price reductions from current practice. This approach is different because specific industrial applications are targeted, most specifically wind turbine blade and light vehicle transportation, where aircraft grade carbon fiber is not required. As a result, researchers are free to adjust both manufacturing process and precursor chemistry to meet the relaxed physical specifications at a lower cost. This report documents the approach and findings of this cooperative research in alternative precursors and advanced conversion for production of cost-effective carbon fiber for energy missions. Due to export control, proprietary restrictions, and CRADA protected data considerations, specific design details and processing parameters are not included in this report.

01 COAL, LIGNITE, AND PEAT↗

The Bikinians

On March 29, 1944, a small contingent of Marines invaded Bikini Atoll. Their mission was to wrest control of the atoll from Japan and, at the same time, prevent the Bikinians from interfering with the ongoing war effort. The Marines found only five Japanese, all dead by suicide, and about 150 starving islanders who also were suffering from such diseases as the Yaws. The Marines fed the Bikinians and secured medical treatment for them. The Bikinians, like all Marshallese, were extremely grateful to be rescued by Americans. Two years later, the Navy landed on Bikini to send the islanders into exile so that their ancestral homeland could be used for Operation Crossroads. On March 7 th , the Bikinians were relocated to uninhabited Rongerik Atoll, where the Navy had built a village complete with twenty-six homes, canvas water tanks, screened toilets, and nine concrete cisterns. Although the accommodations were adequate, the Navy did not understand that uninhabited Marshallese atolls cannot sustain native life. Within two years, the Bikinians would have to be rescued from starvation again.

99 GENERAL AND MISCELLANEOUS↗

Capability to Recover Plutonium-238 in H-Canyon/HB-Line - 13248

Plutonium-238 is used in Radioisotope Thermoelectric Generators (RTGs) to generate electrical power and in Radioisotope Heater Units (RHUs) to produce heat for electronics and environmental control for deep space missions. The domestic supply of Pu-238 consists of scrap material from previous mission production or material purchased from Russia. Currently, the United States has no significant production scale operational capability to produce and separate new Pu-238 from irradiated neptunium-237 targets. The Department of Energy - Nuclear Energy is currently evaluating and developing plans to reconstitute the United States capability to produce Pu-238 from irradiated Np-237 targets. The Savannah River Site had previously produced and/or processed all the Pu-238 utilized in Radioisotope Thermoelectric Generators (RTGs) for deep space missions up to and including the majority of the plutonium for the Cassini Mission. The previous full production cycle capabilities included: Np- 237 target fabrication, target irradiation, target dissolution and Np-237 and Pu-238 separation and purification, conversion of Np-237 and Pu-238 to oxide, scrap recovery, and Pu-238 encapsulation. The capability and equipment still exist and could be revitalized or put back into service to recover and purify Pu-238/Np-237 or broken General Purpose Heat Source (GPHS) pellets utilizing existing process equipment in HB-Line Scrap Recovery, and H-Canyon Frame Waste Recovery processes. The conversion of Np-237 and Pu-238 to oxide can be performed in the existing HB-Line Phase-2 and Phase- 3 Processes. Dissolution of irradiated Np-237 target material, and separation and purification of Np-237 and Pu-238 product streams would be possible at production rates of ∼2 kg/month of Pu-238 if the existing H-Canyon Frames Process spare equipment were re-installed. Previously, the primary H-Canyon Frames equipment was removed to be replaced: however, the replacement project was stopped. The spare equipment is stored and still available for installation. Out of specification Pu-238 scrap material can be purified and recovered by utilizing the HB-Line Phase- 1 Scrap Recovery Line and the Phase-3 Pu-238 Oxide Conversion Line along with H-Canyon Frame Waste Recovery process. In addition, it also covers and describes utilizing the Phase-2 Np-237 Oxide Conversion Line, in conjunction with the H-Canyon Frames Process to restore the H-Canyon capability to process and recover Np-237 and Pu-238 from irradiated Np-237 targets and address potential synergies with other programs like recovery of Pu-244 and heavy isotopes of curium from other target material. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Renovation of Thermal Vacuum Chambers at Idaho National Laboratory (INL) for Testing of Radioisotope Power Systems (RPS)

The Radioisotope Power Systems (RPS) program at Idaho National Laboratory (INL) fuels and performs environmental testing of RPS in support of National Aeronautics and Space Administration (NASA) missions. Recently the programs’ thermal vacuum chambers, housed within INL’s Space and Security Power Systems Facility (SSPSF), underwent successful renovations to improve functional capabilities and system control in support of customer missions. Thermal vacuum system renovations focused primarily on three core functions. The first focus area was integration of semi-automated Programmable Logic Controllers (PLC) to enhance operational feedback and process control. This included the use of numerically controlled vacuum valves and integration of real time feedback from process pressure transducers. Improvements to the system high vacuum pumping technology was the second priority focus. Legacy diffusion pumps were replaced with turbo-molecular and cryogenic pumps to help mitigate the possibility of back streaming diffusion pump oil onto the surface of the test article or radiative cooling surfaces located within the chambers. The third and final core function involved meeting emergent customer thermal requirements. This led to retro-fitting one of the vacuum chambers with a cryogenically cooled Thermal Conditioning Unit (TCU) and thermal shrouds. The TCU utilizes gaseous nitrogen to heat or cool a cylindrical shroud to maintain a set temperature with a programmable range of -I85 °C to I00 °C. With the successful completion of RPS acceptance testing, the newly renovated thermal vacuum chamber systems are operational and better equipped to support testing of Radioisotope Power Systems for space exploration missions.

42 ENGINEERING↗

Renovation of Thermal Vacuum Chambers at Idaho National Laboratory for Testing of Radioisotope Power Systems

The Radioisotope Power Systems (RPS) program at Idaho National Laboratory (INL) fuels and performs environmental testing of RPS in support of National Aeronautics and Space Administration (NASA) missions. Recently the programs’ thermal vacuum chambers, housed within INL’s Space and Security Power Systems Facility (SSPSF), underwent successful renovations to improve functional capabilities and system control in support of customer missions. Thermal vacuum system renovations focused primarily on three core functions. The first focus area was integration of semi-automated Programmable Logic Controllers (PLC) to enhance operational feedback and process control. This included the use of numerically controlled vacuum valves and integration of real time feedback from process pressure transducers. Improvements to the system high vacuum pumping technology was the second priority focus. Legacy diffusion pumps were replaced with turbo-molecular and cryogenic pumps to help mitigate the possibility of back streaming diffusion pump oil onto the surface of the test article or radiative cooling surfaces located within the chambers. The third and final core function involved meeting emergent customer thermal requirements. This led to retro-fitting one of the vacuum chambers with a cryogenically cooled Thermal Conditioning Unit (TCU) and thermal shrouds. The TCU utilizes gaseous nitrogen to heat or cool a cylindrical shroud to maintain a set temperature with a programmable range of -I85 °C to I00 °C. With the successful completion of RPS acceptance testing, the newly renovated thermal vacuum chamber systems are operational and better equipped to support testing of Radioisotope Power Systems for space exploration missions.

42 ENGINEERING↗

Renovation of Thermal Vacuum Chambers at Idaho National Laboratory (INL) for Testing of Radioisotope Power Systems (RPS)

The Radioisotope Power Systems (RPS) program at Idaho National Laboratory (INL) fuels and performs environmental testing of RPS in support of National Aeronautics and Space Administration (NASA) missions. Recently the programs’ thermal vacuum chambers, housed within INL’s Space and Security Power Systems Facility (SSPSF), underwent successful renovations to improve functional capabilities and system control in support of customer missions. Thermal vacuum system renovations focused primarily on three core functions. The first focus area was integration of semi-automated Programmable Logic Controllers (PLC) to enhance operational feedback and process control. This included the use of numerically controlled vacuum valves and integration of real time feedback from process pressure transducers. Improvements to the system high vacuum pumping technology was the second priority focus. Legacy diffusion pumps were replaced with turbo-molecular and cryogenic pumps to help mitigate the possibility of back streaming diffusion pump oil onto the surface of the test article or radiative cooling surfaces located within the chambers. The third and final core function involved meeting emergent customer thermal requirements. This led to retro-fitting one of the vacuum chambers with a cryogenically cooled Thermal Conditioning Unit (TCU) and thermal shrouds. The TCU utilizes gaseous nitrogen to heat or cool a cylindrical shroud to maintain a set temperature with a programmable range of -I85 °C to I00 °C. With the successful completion of RPS acceptance testing, the newly renovated thermal vacuum chamber systems are operational and better equipped to support testing of Radioisotope Power Systems for space exploration missions.

42 ENGINEERING↗