Search NASA⌕ Search

SEARCH · Search NASA

Results for “Module scale model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A wind tunnel flight correlation of Apollo 16 sonic boom

A correlation of sonic boom pressure signatures recorded during reentry of the Apollo 16 command module with wind-tunnel signatures extrapolated to flight distances was made for Mach numbers of 1.83 and 9.71. The flight pressure signatures were recorded by microphones located onboard ships positioned near the ground track, whereas the wind tunnel signatures were measured during a test of a 0.016-scale model of the command module. The agreement between estimates based on wind tunnel data and flight measurements was good at the tested Mach numbers.

Garcia, F., Jr.↗
NASA NTRS1972

A Wind Tunnel Flight Correlation of Apollo 15 Sonic Boom

A correlation of sonic boom pressure signatures recorded during reentry of the Apollo 15 command module with wind-tunnel signatures extrapolated to flight distances has been made for Mach numbers of 1.16 and 4.57. The flight pressure signatures were recorded by pressure sensors located onboard ships positioned near the ground track while the wind-tunnel signatures were measured during tests of a 0.016-scale model of the command module. The agreement between estimates based on wind-tunnel data and flight measurements was better at Mach 4.57 than at Mach 1.16.

Hicks, R. M.↗
NASA NTRS1972

Apollo command module land impact tests

Full-scale-model and actual spacecraft were impact tested to define the emergency land-landing capability of the Apollo command module. Structural accelerations and strains were recorded on analog instrumentation, and a summary to these data is included. The landing kinematics were obtained from high-speed photography. Photographs of the structural damage caused during the tests are included. Even though extensive damage can be expected, the crew will receive nothing more than minor injuries during the majority of the probable landing conditions.

Mccullough, J. E.↗
NASA NTRS1992

Assured crew return vehicle post landing configuration design and test

The 1991-1992 senior Mechanical and Aerospace Engineering Design class continued work on the post landing configurations for the Assured Crew Return Vehicle (ACRV) and the Emergency Egress Couch (EEC). The ACRV will be permanently docked to Space Station Freedom, fulfilling NASA's commitment of Assured Crew Return Capability in the event of an accident or illness aboard Space Station Freedom. The EEC provides medical support and a transportation surface for an incapacitated crew member. The objective of the projects was to give the ACRV Project Office data to feed into their feasibility studies. Four design teams were given the task of developing models with dynamically and geometrically scaled characteristics. Groups one and two combined effort to design a one-fifth scale model of the Apollo Command Module derivative, an on-board flotation system, and a lift attachment point system. This model was designed to test the feasibility of a rigid flotation and stabilization system and to determine the dynamics associated with lifting the vehicle during retrieval. However, due to priorities, it was not built. Group three designed a one-fifth scale model of the Johnson Space Center (JSC) benchmark configuration, the Station Crew Return Alternative Module (SCRAM) with a lift attachment point system. This model helped to determine the flotation and lifting characteristics of the SCRAM configuration. Group four designed a full scale EEC with changeable geometric and dynamic characteristics. This model provided data on the geometric characteristics of the EEC and on the placement of the CG and moment of inertia. It also gave the helicopter rescue personnel direct input to the feasibility study.

Anderson, Loren A.↗
NASA NTRS2012

Modeling a Civil Event Case Study for Consequence Management Using the IMPRINT Forces Module

A critical challenge in the Consequence Management (CM) domain is the appropriate allocation of necessary and skilled military and civilian personnel and materiel resources in unexpected emergencies. To aid this process we used the Forces module in the Improved Performance Research Integration Tool (IMPRINT). This module enables analysts to enter personnel and equipment capabilities, prioritized schedules and numbers available, along with unexpected emergency requirements in order to assess force response requirements. Using a suspected terrorist threat on a college campus, we developed a test case model which exercised the capabilities of the module, including the scope and scale of operations. The model incorporates data from multiple sources, including daily schedules and frequency of events such as fire calls. Our preliminary results indicate that the model can predict potential decreases in civilian emergency response coverage due to an involved unplanned incident requiring significant portions of police, fire and civil responses teams.

Gacy, Marc↗
NASA NTRS1993

Design and Testing of a One-Third Scale Soyuz TM Descent Module Spartan Conversion Project Super Loki Instrumentation

The 1992-1993 senior Aerospace Engineering Design class continued work on the post landing configurations for the Assured Crew Return Vehicle. The Assured Crew Return Vehicle will be permanently docked to the space station fulfilling NASA's commitment of Assured Crew Return Capability in the event of an accident or illness aboard the space station. The objective of the project was to give the Assured Crew Return Vehicle Project Office data to feed into their feasibility studies. Three design teams were given the task of developing models with dynamically and geometrically scaled characteristics. Groups one and two combined efforts to design a one-third scale model of the Russian Soyuz TM Descent Module, and an on-board flotation system. This model was designed to determine the flotation characteristics and test the effects of a rigid flotation and orientation system. Group three designed a portable water wave test facility to be located on campus. Because of additional funding from Thiokol Corporation, testing of the Soyuz model and flotation systems took place at the Offshore Technology Research Center. Universities Space Research Association has been studying the use of small expendable launch vehicles for missions which cost less than 200 million dollars. The Crusader2B. which consists of the original Spartan first and second stage with an additional Spartan second stage and the Minuteman III upper stage is being considered for this task. University of Central Florida project accomplishments include an analysis of launch techniques, a modeling technique to determine flight characteristics, and input into the redesign of an existing mobile rail launch platform.

Anderson, Loren A.↗
NASA NTRS1990

Stratiform clouds and their interaction with atmospheric motion

During 1989 and 1990, the researchers saw the publication of two papers and the submission of a third for review on work supported primarily by the previous contract, NAS8-36150; the delivery of an invited talk at the SIAM Conference on Dynamical Systems in Orlando, Florida; and the start of two new projects on the radiative effects of stratocumulus on the large-scale flow. The published papers discuss aspects of stratocumulus circulations (Laufersweiler and Shirer, 1989) and the Hadley to Rossby regime transition in rotating spherical systems (Higgins and Shirer, 1990). The submitted paper (Haack and Shirer, 1990) discusses a new nonlinear model of roll circulations that are forced both dynamically and thermally. The invited paper by H. N. Shirer and R. Wells presented an objective means for determining appropriate truncation levels for low-order models of flows involving two incommensurate periods; this work has application to the Hadley to Rossby transition problem in quasi-geostrophic flows (Moroz and Holmes, 1984). The new projects involve the development of a multi-layered quasi-geostrophic channel model for study of the modulation of the large-scale flow by stratocumulus clouds that typically develop off the coasts of continents. In this model the diabatic forcing in the lowest layer will change in response to the (parameterized) development of extensive fields of stratocumulus clouds. To guide creation of this parameterization scheme, researchers are producing climatologies of stratocumulus frequency and the authors correlate these frequencies with the phasing and amplitude of the large-scale flow pattern. Researchers discuss the above topics in greater detail.

Clark, John H. E.↗
NASA NTRS1970

Thermal performance and radio-frequency transmissivity of candidate ablation materials for S-band antenna window application on manned spacecraft

A test program was conducted in the MSC 1.5 MW arc-heated facility to evaluate the thermal performance of ablation materials having potential application as radio frequency windows. These tests were conducted for the improvement of omnidirectional antenna operating characteristics during atmospheric reentry. Since a full scale model of the Apollo command service module was available for antenna tests, this mockup was used as a basic for the tests. Test models were subjected to heating conditions simulating the nominal lunar return trajectory (AS-501) and the design trajectories, high heat load and high heating rate. RF measurements were made before and after the arc jet tests to measure attenuation effects due to the thermal degradation of the materials under consideration. The test program demonstrated that additional development is required in materials technology to achieve an ablative system with both good RF transmission characteristics and thermal-structural integrity.

Tillian, D. J.↗
NASA NTRS1967

Dynamic Model Investigation of Water Pressures and Accelerations Encountered During Landings of the Apollo Spacecraft

An experimental investigation was made to determine impact water pressures, accelerations, and landing dynamics of a 1/4-scale dynamic model of the command module of the Apollo spacecraft. A scaled-stiffness aft heat shield was used on the model to simulate the structural deflections of the full-scale heat shield. Tests were made on water to obtain impact pressure data at a simulated parachute letdown (vertical) velocity component of approximately 30 ft/sec (9.1 m/sec) full scale. Additional tests were made on water, sand, and hard clay-gravel landing surfaces at simulated vertical velocity components of 23 ft/sec (7.0 m/sec) full scale. Horizontal velocity components investigated ranged from 0 to 50 ft/sec (15 m/sec) full scale and the pitch attitudes ranged from -40 degrees to 29 degrees. Roll attitudes were O degrees, 90 degrees, and 180 degrees, and the yaw attitude was 0 degrees.

Tests↗
NASA NTRS2013

Modeling and Evaluation of the Global Sea-Salt Aerosol Distribution: Sensitivity to Emission Schemes and Resolution Effects at Coastal/Orographic Sites

One of the major sources of uncertainty in model estimates of the global sea-salt aerosol distribution is the emission parameterization. We evaluate a new sea-salt aerosol life cycle module coupled to the online multi-scale chemical transport model NMMB/BSC-CTM. We compare 5 year global simulations using five state-of-the-art sea-salt open-ocean emission schemes with monthly averaged coarse aerosol optical depth (AOD) from selected AERONET sun photometers, surface concentration measurements from the University of Miami's Ocean Aerosol Network, and measurements from two NOAA/PMEL cruises (AEROINDOEX and ACE1). Model results are highly sensitive to the introduction of sea-surface-temperature (SST)-dependent emissions and to the accounting of spume particles production. Emission ranges from 3888 teragrams per year to 8114 teragrams per year, lifetime varies between 7.3 hours and 11.3 hours, and the average column mass load is between 5.0 teragrams and 7.2 teragrams. Coarse AOD is reproduced with an overall correlation of around 0.5 and with normalized biases ranging from +8.8 percent to +38.8 percent. Surface concentration is simulated with normalized biases ranging from minus 9.5 percent to plus 28 percent and the overall correlation is around 0.5. Our results indicate that SST-dependent emission schemes improve the overall model performance in reproducing surface concentrations. On the other hand, they lead to an overestimation of the coarse AOD at tropical latitudes, although it may be affected by uncertainties in the comparison due to the use of all-sky model AOD, the treatment of water uptake, deposition and optical properties in the model and/or an inaccurate size distribution at emission.

Bias↗
NASA NTRS1990

Turbulence modulation effect on evaporating spray characterization

The effects of turbulence modulation on the evaporating spray characteristics of a liquid fuel jet are numerically investigated. Two modulation models are implemented into the k-epsilon two-equation model. The gas phase is solved by a pressure-based method on a Eulerian frame and droplets are solved by a stochastic discrete particle technique based on Lagrangian formulation. The k-epsilon models are used to characterize the time and length scales of the gas phase turbulence for droplet dispersions and droplet/turbulence interactions. The modulation models are found to have significant effects on gas phase dynamics, and are less important for the droplet dynamics. Numerical predictions are compared with the experimental data of Drallemier and Peters (1990).

Shang, H. M.↗
NASA NTRS1985

Boundary layer control of nocturnal convection associated with a synoptic scale system

Well defined nocturnal convection, together with distinct maximum precipitation events in Nebraska, were associated with strong diurnal wind oscillations at 850 mb in Oklahoma, Kansas and Missouri in the present study of pronounced precipitation and low level circulation variations over the Great Plains on May 5-10, 1979. A numerical prediction model, used to relate boundary layer flow modulations to synoptic scale flow for this case, is driven by a diurnal cycle. Experimental forecasts displayed diurnal wind modulations at 500 m, with rising motions of the order of 4 cm/sec at the 2200 m level, along the leading edge of the nocturnal jet.

Astling, E. G.↗
NASA NTRS1980

Jupiter's magnetopause, bow shock, and 10-hour modulated magnetosheath: Voyagers 1 and 2

Fine scale magnetic field data from the Voyager 1 and 2 magnetopause and bow shock crossings at Jupiter were analyzed. Explicit models of the dawnside magnetopause and bow shock in Jupiter's orbital plane employ an axisymmetric parabola and hyperbola, respectively, and are determined separately for the encounters. A new phenomenon was discovered in the magnetosheath. It is manifested as (5 or) 10 hour quasi-periodic modulation of the direction of the magnetic field in the outbound magnetosheath, predominantly in the northward (N) and southward (S) directions. It was seen to occur during both encounters and appears most evident in Voyager 2 outbound observations, probably due to the extreme tailward extent of the Voyager 2 trajectory through the magnetosheath. The durations of the N to and from S transitions range from tens of minutes to approximately 3 hours. The directional variation of the field during these transitions is fairly well restricted to a plane parallel to the local model magnetopause location. These signatures may be due to magnetosheath field line draping modulated by the large scale motion of the magnetospheric plasma disk.

Lepping, R. P.↗
NASA NTRS1990

A Probable Approx. 2400 Year Solar Quasi-cycle in Atmospheric Delta C-14

A 2200 to 2600 year quasi-periodicity is present in atmospheric delta C-14 records after removal of long-term trends due to the geomagnetic dipole amplitude variation. This periodicity consists of both a long-term variation of the mean and a superposed, approximately recurring pattern of century-scale variations. The strongest of these latter variations occur near maxima of the approx. 2400 year delta C-14 cycles. The residual record can be modeled to first order as an amplitude modulation of a century-scale periodic forcing function by a approx. 2400 year periodic forcing function. During the last millennium, the largest century-scale variations (occurring near the most recent 2400 year delta C-14 maximum) are known to be mainly a consequence of the pronounced Maunder, Sporer, and Wolf solar activity minima, as verified by independent proxy solar activity records. Therefore, during this period, amplitude modulation has been occurring primarily in the sun and not in the terrestrial radiocarbon system. It is therefore inferred that the approx. 2400 year forcing function is mainly solar although some secondary terrestrial feedback into the delta C-14 record is likely. This conclusion has implications for the predictability of future pronounced solar activity minima and for the interpretation of certain minor Holocene climatic variations.

Hood, L. L.↗
NASA NTRS1999

ISS Propulsion Module Crew Systems Interface Analysis in the Intelligent Synthesis Environment

ERGO, a human modeling software for ergonomic assessment and task analysis, was used for the crew systems interface analysis of the International Space Station (ISS) Propulsion Module (PM). The objective of analysis was to alleviate passageway size concerns. Three basic passageway configuration concepts: (1) 45" clear passageway without centerline offset (2) 50" clear passageway, 12" centerline offset, (3) 50" clear passageway, no centerline offset, and were reviewed. 95 percentile male and female models which were provided by the software performed crew system analysis from an anthropometric point of view. Four scenarios in which the crew floats in microgravity through a 50" no-offset passageway as they carry a 16" x 20" x 30" avionics box were simulated in the 10-weeks of intensive study. From the results of the analysis, concept (3) was the preferred option. A full scale, three-dimensional virtual model of the ISS Propulsion Module was created to experience the sense of the Intelligent Synthesis Environment and to evaluate the usability and applicability of the software.

Chen, Di-Wen↗