Search NASA⌕ Search

SEARCH · Search NASA

Results for “NEQAIR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Coupled Fluids-Radiation Analysis of a High-Mass Mars Vehicle

The NEQAIR line-by-line radiation code has been incorporated into the DPLR Navier-Stokes flow solver such that the NEQAIR subroutines are now callable functions of DPLR. The coupled DPLR-NEQAIR code was applied to compute the convective and radiative heating rates over high-mass Mars entry vehicles. Two vehicle geometries were considered - a 15 m diameter 70-degree sphere cone configuration and a slender, mid-L/D vehicle with a diameter of 5 m called an Ellipsled. The entry masses ranged from 100 to 165 metric tons. Solutions were generated for entry velocities ranging from 6.5 to 9.1 km/s. The coupled fluids-radiation solutions were performed at the peak heating location along trajectories generated by the Traj trajectory analysis code. The impact of fluids-radiation coupling is a function of the level of radiative heating and the freestream density and velocity. For the high-mass Mars vehicles examined in this study, coupling effects were greatest for entry velocities above 8.5 km/s where the surface radiative heating was reduced by up 17%. Generally speaking, the Ellipsled geometry experiences a lower peak radiative heating rate but a higher peak turbulent convective heating rate than the MSL-based vehicle.

Palmer, Grant↗
NASA NTRS2016

DSMC Shock Simulation of Saturn Entry Probe Conditions

This work describes the direct simulation Monte Carlo (DSMC) investigation of Saturn entry probe scenarios and the influence of non-equilibrium phenomena on Saturn entry conditions. The DSMC simulations coincide with rarefied hypersonic shock tube experiments of a hydrogen-helium mixture performed in the Electric Arc Shock Tube (EAST) at NASA Ames Research Center. The DSMC simulations are post-processed through the NEQAIR line-by-line radiation code to compare directly to the experimental results. Improved collision cross-sections, inelastic collision parameters, and reaction rates are determined for a high temperature DSMC simulation of a 7-species H2-He mixture and an electronic excitation model is implemented in the DSMC code. Simulation results for 27.8 and 27.4 kms shock waves are obtained at 0.2 and 0.1 Torr respectively and compared to measured spectra in the VUV, UV, visible, and IR ranges. These results confirm the persistence of non-equilibrium for several centimeters behind the shock and the diffusion of atomic hydrogen upstream of the shock wave. Although the magnitude of the radiance did not match experiments and an ionization inductance period was not observed in the simulations, the discrepancies indicated where improvements are needed in the DSMC and NEQAIR models.

Modeling↗
NASA NTRS2016

DSMC Shock Simulation of Saturn Entry Probe Conditions

This work describes the direct simulation Monte Carlo (DSMC) investigation of Saturn entry probe scenarios and the influence of non-equilibrium phenomena on Saturn entry conditions. The DSMC simulations coincide with rarefied hypersonic shock tube experiments of a hydrogen-helium mixture performed in the Electric Arc Shock Tube (EAST) at the NASA Ames Research Center. The DSMC simulations are post-processed through the NEQAIR line-by-line radiation code to compare directly to the experimental results. Improved collision cross-sections, inelastic collision parameters, and reaction rates are determined for a high temperature DSMC simulation of a 7-species H2-He mixture and an electronic excitation model is implemented in the DSMC code. Simulation results for 27.8 and 27.4 km/s shock waves are obtained at 0.2 and 0.1 Torr, respectively, and compared to measured spectra in the VUV, UV, visible, and IR ranges. These results confirm the persistence of non-equilibrium for several centimeters behind the shock and the diffusion of atomic hydrogen upstream of the shock wave. Although the magnitude of the radiance did not match experiments and an ionization inductance period was not observed in the simulations, the discrepancies indicated where improvements are needed in the DSMC and NEQAIR models.

Higdon, Kyle J.↗
NASA NTRS2019

Full Facility Shock Frame Simulations of the Electric Arc Shock Tube

Radiative heating computations are performed for high speed lunar return experiments conducted in the Electric Arc Shock Tube (EAST) facility at NASA Ames Research Center. The nonequilibrium radiative transport equations are solved via NASA's in-house radiation code NEQAIR using flow field input from US3D flow solver. The post-shock flow properties for the 10 km/s Earth entry conditions are computed using the stagnation line of a blunt-body and a full facility CFD (Computational Fluid Dynamics) simulation of the EAST shock tube. The shocked gas in the blunt-body flow achieves a thermochemical equilibrium away from the shock front whereas EAST flow exhibits a nonequilibrium behavior due to strong viscous dissipation of the shock by boundary layer. The full-tube flow calculations capture the influence of the boundary layer on the shocked gas state and provide a realistic fluid dynamic input for the radiative predictions. The integrated radiance behind the shock is calculated in NEQAIR for wavelength regimes from Vacuum-UltraViolet (VUV) to InfraRed (IR), which are pertinent to the emission characteristics of high enthalpy shock waves in air. These radiance profiles are validated against corresponding EAST shots. The full-tube simulations successfully predict a sharp radiance peak at the shock front which gets smeared in the test data due to the spatial resolution in the measurements. The full facility based radiance behind the shock shows a slightly better match with the test data in the VUV and Red spectral regions, as compared to that from a blunt-body based predictions. The UV radiance is very similar for both geometries and under-predicts the test behavior. The IR test data matches better with the blunt-body based predictions where the full-tube simulations show a significant over-prediction.

Radiation↗
NASA NTRS2019

Simulation Schiaparelli's Entry and Comparison to Aerothermal Flight Data

The European Space Agency recently flew an entry, descent, and landing demonstrator module called Schiaparelli that entered the atmosphere of Mars on the 19th of October, 2016. The instrumentation suite included heatshield and backshell pressure transducers and thermocouples (known as AMELIA - Atmospheric Mars Entry and Landing Investigations and Analysis) and backshell radiation and direct heat flux-sensing sensors (known as COMARS (Combined Aerothermal and Radiometer Sensors Instrument Package) and ICOTOM (narrow band radiometers)). Due to the failed landing of Schiaparelli, only a subset of the flight data was transmitted before and after plasma black-out. The goal of this paper is to present comparisons of the flight data with calculations from NASA simulation tools, DPLR (Data Parallel Line Relaxation) / NEQAIR (NonEQuilibrium AIr Radiation) and LAURA (Langley Aerothermodynamic Upwind Relaxation Algorithm) / HARA (High-temperature Aerothermodynamic RAdiation ). DPLR and LAURA are used to calculate the flowfield around the vehicle and surface properties, such as pressure and convective heating. The flowfield data are passed to NEQAIR and HARA to calculate the radiative heat flux. Comparisons will be made to the COMARS total heat flux, radiative heat flux and pressure measurements. Results will also be shown against the reconstructed heat flux which was calculated from an inverse analysis of the AMELIA thermocouple data performed by Astrium. Preliminary calculations are presented in this abstract.

Brandis, A. M.↗
NASA NTRS2016

DSMC Shock Simulation of Saturn Entry Probe Conditions

This work describes the direct simulation Monte Carlo (DSMC) investigation of Saturn entry probe scenarios and the influence of non-equilibrium phenomena on Saturn entry conditions. The DSMC simulations coincide with rarefied hypersonic shock tube experiments of a hydrogen-helium mixture performed in the Electric Arc Shock Tube (EAST) at NASA Ames Research Center. To directly compare to the experimental results, the DSMC simulations are post-processed through the NEQAIR line-by-line radiation code. Improved collision cross-sections, inelastic collision parameters, and reaction rates are determined for a high temperature DSMC simulation of a 7-species H2-He mixture and an electronic excitation model is implemented in the DSMC code. Simulation results for 27.8 and 27.4 kms shock waves are obtained at 0.2 and 0.1 Torr respectively and compared to measured spectra in the VUV, UV, visible, and IR ranges. These results confirm the persistence of non-equilibrium for several centimeters behind the shock and the diffusion of atomic hydrogen upstream of the shock wave. Although the magnitude of the radiance did not match experiments and an ionization inductance period was not observed in the simulations, the discrepancies indicated where improvements are needed in the DSMC and NEQAIR models.

Saturn↗
NASA NTRSDate not supplied

ANALYSIS OF THE MSL/MEDLI ENTRY DATA WITH COUPLED CFD AND MATERIAL RESPONSE.

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heat-shield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material. PICA is a lightweight carbon fiber/polymeric resin material that offers out-standing performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on Open-FOAM (PATO) using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA, is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Mars Science Laboratory↗
NASA NTRSDate not supplied

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗
NASA NTRSDate not supplied

Aerothermal Analysis of the Dragonfly Titan Entry

The Dragonfly mission will send a rotorcraft lander to the surface of Saturn’s moon Titan as part of the New-Frontiers program. This will be the first spacecraft to land on Titan since the Huygens probe’s descent in January of 2005 and only the second spacecraft to enter Titan’s atmosphere. The Dragonfly entry capsule is significantly larger than the Huygens probe and will experience higher aerothermal environments. This poster will provide an overview of the aerothermodynamic models used in the Dragonfly aeroshell design process. Titan provides a unique entry environment that has several fundamental differences from the environments at the more common entry destinations of Earth and Mars. The lack of atmospheric oxygen significantly reduces heatshield recession (expected to be negligible), which simplifies material response analysis but also reduces the efficiency of the thermal protection system. The atmos-phere is composed of mostly nitrogen and trace amounts of methane. During hypersonic entry this methane dissociates and leads to the formation of the molecule CN, which is known to radiate strongly in the shock layer. Current Dragonfly heating predictions estimate that radiation contributes about 50% of the total heat flux along the forebody and up to 90% on the aftbody, making radiation a key element of aerothermal analysis. To properly address the importance of radiation, a unique radiative-heating correlation was developed that incorporates normal-shock equilibrium chemistry predictions based on work from the Mars 2020 program. These new heating correlations agree well with Computational Fluid Dynamics (CFD) predictions and enable large-scale trajectory analyses by providing rapid heating predictions along candidate trajectories. Dragonfly aerothermal environments are generated with the Data Parallel Line Relaxation (DPLR) finite-volume Navier-Stokes solver alongside the Nonequilibrium Radiative Transport and Spectra (NEQAIR) radiation transport code. DPLR produces shock-aligned flowfields that incorporate the effects of both chemical and thermal nonequilibrium while NEQAIR solves the radiation transport equations along lines-of-sight through the flowfield solutions to predict the radiative heating on the aeroshell. Titan’s atmosphere produces complex thermal and chemical nonequilibria and so classical radiation approximations that extrapolate from a single line-of-sight, such as the Tangent-Slab method, were found to overpredict peak radiative heat fluxes by 10-20%. Therefore, all radiative heating is directly calculated using 3-D transport for both the forebody and aftbody to reduce unnecessary conservatism. A 21-species finite-rate chemistry model, including electrons and ionized species, is used in the CFD to ensure accurate vehicle heating predictions (the level of ionization is particularly for accurate radiative flux predictions). This poster will cover: 1) The models and assumptions used to simulate entry into Titan’s atmosphere, 2) Dragonfly aerothermal engineering correlations alongside statistical heating values, and 3) Driving aerothermal considerations for a Titan entry such as CN formation and radiation-flowfield coupling.

EDL↗
NASA NTRS1985

Nonequilibrium air radiation (Nequair) program: User's manual

A supplement to the data relating to the calculation of nonequilibrium radiation in flight regimes of aeroassisted orbital transfer vehicles contains the listings of the computer code NEQAIR (Nonequilibrium Air Radiation), its primary input data, and explanation of the user-supplied input variables. The user-supplied input variables are the thermodynamic variables of air at a given point, i.e., number densities of various chemical species, translational temperatures of heavy particles and electrons, and vibrational temperature. These thermodynamic variables do not necessarily have to be in thermodynamic equilibrium. The code calculates emission and absorption characteristics of air under these given conditions.

Park, C.↗
NASA NTRS1986

Assessment of two-temperature kinetic model for dissociating and weakly-ionizing nitrogen

The validity of the author's two-temperature, chemical/kinetic model which the author has recently improved is assessed by comparing the calculated results with the existing experimental data for nitrogen in the dissociating and weakly ionizing regime produced behind a normal shock wave. The computer program Shock Tube Radiation Program (STRAP) based on the two-temperature model is used in calculating the flow properties behind the shock wave and the Nonequilibrium Air Radiation (NEQAIR) program, in determining the radiative characteristics of the flow. Both programs were developed earlier. Comparison is made between the calculated and the existing shock tube data on (1) spectra in the equilibrium region, (2) rotational temperature of the N2(+) B state, (3) vibrational temperature of the N2(+) B state, (4) electronic excitation temperature of the N2 B state, (5) the shape of time-variation of radiation intensities, (6) the times to reach the peak in radiation intensity and equilibrium, and (7) the ratio of nonequilibrium to equilibrium radiative heat fluxes. Good agreement is seen between the experimental data and the present calculation except for the vibrational temperature. A possible reason for the discrepancy is given.

Park, C.↗
NASA NTRS1989

Nonequilibrium shock layer temperature profiles from arc jet radiation measurements

Shock layer temperature profiles are obtained through analysis of radiation from shock layers produced by a blunt body inserted in arc jet flow. Spectral measurements have been made in a nitrogen flow of 54.4 gm/s at an enthalpy of 8.72 MJ/kg. Vibrational temperatures for N2+ are obtained by matching spectral regions from arc jet spectra with spectra generated using the NEQAIR code. Temperature profiles obtained from the radiation layers show a vibrational temperature higher than the rotational temperature near the front of the shock and both temperatures decrease as the flow approaches the body. The spectral measurements are made and analysis completed for four distances, from the surface of the blunt body. The corresponding shock layer thickness is approximately 3.6 cm. Although the shock layer appears to be in thermal nonequilibrium, the measured rotational temperature approaches the single temperature results of viscous shock layer calculations at this test condition.

Blackwell, Harvel E.↗
NASA NTRS1990

An approximate method for the calculation of nonequilibrium radiative heat transfer

A simplified method for the calculation of radiative heat transfer in hypersonic reentry flows where local thermal nonequilibrium (LTNE) conditions exist is presented. This method has been incorporated into the computer code RADMC (RADiation/Modified Corrections), which utilizes an approximate 'two-state' model of the electronic levels of atoms and molecules in the determination of the populations of the excited states for both LTNE and local thermal equilibrium (LTE) conditions for each of the relevant chemical species. The population data are used to calculate a correction factor to the radiative cross sections in an eight-step nongray radiative heat-transfer model. Results have been obtained for various points along the proposed trajectory of the Aeroassist Flight Experiment and the Fire II trajectory, and compared with results obtained for the same flowfields from the NEQAIR radiative heat-transfer code.

Greendyke, Robert B.↗
NASA NTRS1991

Calculation of convective and radiative heating on the forebody heatshield of the aeroassist flight experiment vehicle

The total (convective and radiative) heating is calculated over the entire forebody heatshield of the Aeroassist Flight Experiment (AFE) vehicle. The convective heating is calculated using a three-dimensional Navier-Stokes code (LAURA) which includes both chemical and thermal nonequilibrium effects. The flowfield solution is then used to provide inputs to a nonequilibrium air radiation code (NEQAIR) to calculate the nonequilibrium radiative heating. Results are presented at two points on the current Baseline 5A trajectory corresponding to the start of the primary data taking period and peak heating.

Hamilton, H. Harris, II↗
NASA NTRS1991

ARCFLO analysis for high-enthalpy arc heaters

Feasibility, physical constraints, and preliminary design and operating envelope are calculated for a next-generation segmented arc heater with enthalpies of 70-90 MJ/kg, for simulation of fast lunar or Martian return trajectories. The ARCFLO computer program is modified for improved accuracy in high-enthalpy radiation-dominated flows. The ARCFLO band-radiation model is compared with the state-of-the-art spectral-radiation code NEQAIR. The band-radiation model is corrected, and band-absorption coefficients are reduced by up to 40 percent at high temperatures. Parametric studies show that, with conventional wall-heating limitations, high mass flow and high enthalpy are contradictory design goals owing to the increase of radiation losses with pressure, current density, and constrictor diameter. With existing hardware limitations, an enthalpy of 70 MJ/kg with a flow rate of 0.1 kg/s can be achieved in a constrictor with 5-6 cm diameter operating near 3-atm stagnation pressure. The total power is under 100 MW, but the current is very high: 14,000-18,000 amperes.

Milos, Frank S.↗
NASA NTRS1991

Computational methodology for radiation heat transfer in the flowfield of an AOTV

A computational methodology is developed for the calculation of radiation heat transfer in a non-scattering medium where nonequilibrium conditions exist and give rise to complex spectra. The specific problem of radiation in an aeroassisted orbital transfer vehicle (AOTV) flowfield is addressed. Nonequilibrium radiation from the gases around a hypersonic vehicle is evaluated using the NASA-Ames NEQAIR program together with a three-dimensional geometrical flowfield model. Nonequilibrium compositions and temperatures are taken from NASA-Langley 3-D hypersonic flowfield calculations that include real-gas effects and finite-rate chemical kinetics. It is shown that the concept of a transmission path adjustment, together with precomputations of curves of growth based upon local properties at flowfield locations, facilitates radiation calculations. Sample calculations of directional and spectral distributions of gas radiation received upon a hypersonic vehicle are presented.

Fuehrer, P. L.↗
NASA NTRS1992

Experimental study and improved modeling of high-temperature air radiation

Spectral emission measurements were conducted in an atmospheric pressure air plasma. The thermodynamic state of the plasma was determined to be close to local thermodynamic equilibrium (LTE), and the temperature profile was measured. The spectrum emitted by the plasma over the range 2,000 to 8,000 A was recorded and calibrated. This spectrum comprises the major radiating molecular bands and atomic lines in air, and is therefore proposed as a benchmark to test radiative calculations. A comparison of these results with the predictions of the NEQAIR code induced several modeling improvements in the code. In particular, radiative transition probabilities and spectroscopic constants were updated, and additional band systems of NO (NO Delta, Epsilon, Beta prime and Gamma prime) were included. Since the C state from which the NO Delta transition originates is predissociated, a simplified collision-predissociation model for this state was added to the code. These changes are presented, and their effect discussed.

Laux, Christophe O.↗
NASA NTRS1992

A parametric analysis of radiative structure in aerobrake shock layers

A broad-spectrum version of the NEQAIR code was modified to account for self-absorption and applied to AFE flowfields calculated by the LAURA code with a variety of kinetic models. The resulting radiative fluxes were obtained in a decoupled fashion from the flowfield solver along the vehicle's stagnation streamline. The radiative flux obtained was broken down by causative process to study the radiative structure of the AFE's flowfield for the various kinetic models. In addition, the radiative fluxes for several points on a typical AFE trajectory were analyzed to examine how the radiative structure changes as the vehicle completes its aeropass. Only two radiative processes dominated the stagnation radiative flux, and the flow field conditions near the wal were found to exert considerable influence over the radiative flux to the wall.

Greendyke, Robert B.↗