Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ni coarsening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Inhomogeneous Distribution and Coarsening of y″ Precipitates in a Ni-Based Superalloy and Their Effect on Creep

It has been reported that the addition of Nb or Ta in the high Ti/Al ratio alloys promotes the formation of y″ precipitates solely and greatly contributes to the elevated temperature strength and resistance to creep deformation. In this study, the y''-dominant INCONEL alloy 725 (IN725) variants (named M725-Nb/Ta) modified with a high level of Nb/Ta additions and high Ti/Al ratio was chosen as a model alloy for microstructural observation of y'' variants upon creep. Following the high temperature aging (HTA), y'' was found to be the main strengthening precipitate with no detectable y’ in both M725 alloys. After creep, the grip/gage sections of the crept M725-Nb/Ta exhibited preferential coarsening and inhomogeneous distribution of y''. That is, one or two of the variants were preferentially coarsened at the expense of another variant, and sandwich-like structures, comprising of cubic y′ precipitates with small y″ discs on each face, were formed. This variant selection behavior taking place in the grip section with no stress applied was different from the typical stress-induced variant selection in previous literature. However, the sample with prior high temperature exposure (700 °C for 500 hours) with varying y″ characteristics demonstrated a similar trend of creep when compared with those in the HTA sample, suggesting that the coarsening and the inhomogeneous distribution of y'' was not the determinant of creep life in bulk M725-Nb/Ta alloys.

Hung, Chang-Yu↗
DOE OSTI2023

Reversible solid oxide cells: Early performance and microstructural evolution during electrolysis and switched mode operation

Incorporating more renewables into our energy mix will require a diversity of technological solutions. Reversible solid oxide cell systems (RSOCs) operating reversibly between fuel cell and electrolysis modes with high round-trip efficiencies offer one such solution. However, questions remain about the stability of the oxygen and fuel electrodes under reversible operation. Here, in this study, single cells with the configuration Ni-YSZ|YSZ|GDC10|NNO-NDC50|NNO are operated by reversible cycling under potentiostatic conditions. Test conditions are chosen to be representative of average stack conditions that are likely to be encountered during operation of a stack constructed of such cells. The results of reversible cycling over 500 h (21 cycles) are compared with operating the cells under potentiostatic conditions in the electrolysis-only mode (i.e., without cycling). Voltage-current density (DC), AC complex impedance spectroscopy, distribution of relaxation times (DRT) analysis, and scanning electron microscopy (SEM) indicate excellent reversibility and stability of the neodymium nickelate-based oxygen electrodes in both electrolysis and reversible cycling modes. Degradation behavior is attributed to the loss and coarsening of connected Ni particles in the fuel electrode, particularly in the active layer. However, reversible operation mitigates this degradation compared to operation in the electrolysis-only (SOEC-only) mode.

25 ENERGY STORAGE↗
DOE OSTI2022

Scalable Nano-Scaffold SOFC Anode Architecture Enabling Direct Hydrocarbon Utilization

This project is based on WVU’s pending patents, technology and aims to design and modify the internal surfaces of the Ni/YSZ anode from currently commercially viable Solid Oxide Fuel Cells (SOFCs) using the additive manufacturing process of Atomic Layer Deposition (ALD). The surface architecture/scaffold added onto the internal surface of the anode possesses an engineered nanostructure but it features only commonly-used oxide conductors and electro-catalyst materials. The surface layer possesses a minimum thickness of ~2-40 nm and is solely designed to control the surface reforming reactions and to increase catalytic activity. Three-dimensional (3D) nano scaffold architectures with the noble metal nano-catalyst, low-cost bimetallic catalytic alloys, and nano-scale ionic conducting oxide fully compatible with the state-of-the-art Ni/YSZ anode, were applied to the internal surface of the entire porous SOFC anode using ALD. In the present work, the surface scaffold architecture is essentially multi-functional at the nano-scale, facilitated by the multiple heterostructured interfaces. It will significantly enhance the power density and cell durability for direct hydrocarbon utilization by (1) increasing the number of electrochemical reaction sites to enhance the hydrogen/hydrocarbon oxidation reactions; (2) reducing carbon formation; (3) mitigating the coarsening of backbone Ni phase and the oxidation attack of Ni from oxidants (e.g., H2O, CO2); and (4) promoting the internal reforming capabilities, especially for natural gas applications. ALD is employed to generate stable anode surface architectures that are uniform, precisely controllable at the atomic scale, and accurately repeatable for processing. The engineered anode surface nano-scaffold architecture was cataloged and analyzed using High-resolution Transmission Electron Microscopy (TEM), and cell power/durability performance assessed via comprehensive electrochemical performance testing with commercial specimens and relevant environments using hydrocarbon fuels. To the best of our knowledge, this project is the First Report on ALD of Ni/YSZ. The actual achievement of this Project includes (1). Successful demonstration of 7 types of ALD layers on Ni/YSZ anode, including Co, Ni, Mn, Pt, Ru, ZrOx and multi-functional nano-composite. (1). Conformal coating and subsequently spontaneously pinning the discrete nano-catalyst, including the precious metal nano-catalyst and the Ni and Co catalysts, on the YSZ surface upon the electrochemical operation in the reduced atmosphere. Those nano-catalysts on the ionic-conducting YSZ provided excellent sites for promoting internal reforming; (2). Demonstrated ALD coating increased both catalytic activity and conductivity of Ni/YSZ. Conformal coating provided dopants and introduced additional electrical conducting pathways on the YSZ ionic conductor. The doped surface layer of YSZ with mixed conductivity thus further introduces the active triple phase boundaries adjacent to the ALD-coated nano-catalysts such as Pt, Co, and Ni that are pinned on the YSZ surface. The nano-composite ALD coating on Ni/YSZ anode has significantly increased cell durability; and (3). ALD coating of Ni/YSZ anode increased the power density of the entire cell by 300%. For a long time, the SOFC performance, such as the power density, was deemed hindered by the cathode. The sluggish oxygen reduction reaction (ORR) in the cathode was deemed as hindering the power density of the SOFCs. For the anode-supported commercial SOFCs, the cell performance is considered to be limited by the cathode's performance. For the first time in the field of SOFC, this project has demonstrated that (1). the performance of commercial SOFCs can be further increased by the ALD coating on Ni/YSZ anode backbone. (2). ALD coating on Ni/YSZ fuel electrodes results in the enhancement of power density, and increased reliability, robustness, and endurance of SOFCs, for their application using both hydrogen and hydrocarbon fuels over the entire operating temperature range of 650-800ºC for the inherently functional commercial cells. (3). ALD coating provides alternative approaches of exsolutions for introducing the stable catalyst onto the internal surface of the Ni/YSZ electrode. ALD coating could be much more versatile than exsolution in employing the catalysts with various chemistries onto the various backbones. (4). Due to the negligible amount of ALD materials coated onto the internal surface of the porous cathode of the as-fabricated cells, a peak power density increase up to 300 % induced by ALD coating was simultaneously achieved in terms of both power density and specific power. (5). The ALD coating developed through this project was applied to both the SOFC and Solid Oxide Electrolysis Cells (SOEC). SOEC’s face a similar but more demanding need to improve the fuel electrode's performance. It opens further research directions for electrocatalytic surface nanoionics with a wide range of chemistry. It will revolutionize our ability to render the formation of a nanostructured electrode that has been constantly pursued yet barely achieved for practical SOFC/SOEC applications. The research is also immediately transformative since both the preliminary data and the proposed work are on the direct implantation of nanoionics into the state-of-the-art inherently functional SOCs. It represents an immediate impact on the commercial sectors in SOC technology since the applied ALD processing is computer-controlled ALD coating using the commercial ALD systems, and it is scalable to both the single cells and SOC stacks.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Uses of Computed Tomography for Characterizing Materials Grown Terrestrially and in Microgravity

Tomography (CT) has proved to be of inestimable use in providing a rapid evaluation of a variety of samples from Mechanics of Granular Materials (MGM) to electronic materials (Ge-Si alloys) to space grown materials such as meteorites. The system at Kennedy Space Center (KSC), because of its convenient geographical location, is ideal for examining samples before launch and immediately after returning to Earth. It also has the advantage of the choice of fluxes, and in particular the use of a radioactive cobalt source, which is basically monochromatic. This permits a reasonable measurement of density to be made from which chemical composition can be determined. Due to the current dearth of long duration space grown materials, the CT instrument has been used: (1) to characterize materials in preparation for flight, (2) to determine thermal expansion values, and (3) to examine long duration space grown materials, i.e. meteorites. This work will first describe the establishment of the protocol for obtaining the optimum density readings for any material. Included will be the effects of the hardware or instrumental parameters that can be controlled, and the techniques used to process the CT data. Examples will be given of the compositional variation along a single crystal of Ge-Si alloy. Density variation with temperature has been measured in preparation for future materials science experiments; this involved the fabrication at MSFC and installation of a single zone furnace at KSC incorporating a heat pipe to ensure high temperature uniformity. At the time of writing the thermal expansion of lead (Pb) has been measured from room temperature to 900 C. Three methods are available. Digital radiography enables length changes to be determined. Prior to melting the sample is smaller than the container and the diameter change can be measured. Most critical, however, is the density change in solid, through the melting region, and in the liquid state. These data are needed for engineering purposes to aid in the design of containment cartridges, and for enabling fluid flow calculations. A second sample, with the Pb alloyed with Sb is ready for scanning. This corresponds to the planned composition of Dr. Poirier s flight experiment. Other materials pertinent to NASA programs such as Al-Cu (Trivedi), CdTe (Banish), HgCdTe (Lehoczky) will be examined below and above the melting point. Finally, three-dimensional results will be shown of the structure of a two-phase metallic meteorite of metal and sulfide, in which the Fe-Ni phase has coarsened during slow cooling over hundreds of millions of years.

Source record↗
DOE OSTI2021

Microstructure and creep properties of cast near-eutectic Al–Ce–Ni alloys

This study investigates the as-cast and aged microstructures, thermal stability, ambient temperature strengthening, and creep resistance of three ternary Al–Ce–Ni alloys (wt%): near-eutectic Al–10Ce–5Ni (with both eutectic and hypoeutectic regions), hypoeutectic Al-7.5Ce-3.75Ni (with numerous primary Al dendrites), and hypereutectic Al-12.5Ce-6.25Ni (with coarse, blocky primary Al3Ni and Al11Ce3 precipitates and some primary Al dendrites). Depending on the alloy composition and local solidification conditions, the following eutectic morphologies are found: (i) coarse Al–Ce eutectic colonies where Al 11 Ce 3 is in the form of “Chinese script”, (ii) intermingled regions of binary Al–Ce and Al–Ni eutectic colonies, with finer Al 3 Ni and Al 11 Ce 3 fibers, (iii) large ternary eutectic colonies, where the binary Al 3 Ni and Al 11 Ce 3 phases are alternating or intertwining within the individual, fine fibers (diameters of ~60–170 nm, depending on solidification rates), and (iv) ternary eutectic zones (between primary Al dendrites), where fine Al 3 Ni and Al 11 Ce 3 build up a 3D-interconnected network. The high volume fraction of intermetallic phases and extremely fine eutectic spacing/fiber diameter both contribute to high ambient strengthening (higher as-cast microhardness than binary Al–Ce or Al–Ni), and also provide enhanced creep resistance at 300 and 350 °C. Additionally, the alloys are coarsening-resistant up to 425 °C for extended periods, with a gradual decrease in microhardness. The alloys aged at 400 °C to 1050 h show fiber fragmentation and coarsening of the resulting particles, with the faster-diffusing Ni driving more rapid coarsening of the Al 3 Ni particles which engulf finer, more stable Al 11 Ce 3 particles. Severe overaging (performed at 590 °C for 24 h) leads to Al 3 Ni and Al 11 Ce 3 spheroids which remain submicron-sized in eutectic colonies, but micron-sized at colony boundary and at Al dendrite-eutectic interface. Creep resistance at 300 °C of overaged Al–10Ce–5Ni remains substantial, consistent with load-transfer based composite strengthening being an important strengthening mechanism in these alloys, making them excellent candidates for replacement of heavier steel or titanium parts operating under stress up to 300 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A high strength Al-2Ni-0.5Zr conductor alloy fabricated via laser powder bed fusion

There is a current need for new aluminum alloy design strategies to target applications requiring high strength and conductivity with reductions in mass. A new lightweight Al-2Ni-0.5Zr (wt. %) conductor alloy was fabricated using laser powder bed fusion. A design of experiments probed the alloy's solidification cracking susceptibility. It was observed that solidification cracking was generally reduced with fast scan speeds, above 1500 mm/s, and smaller hatch spacings. The different cooling rates throughout the melt pool produced a heterogeneous distribution of cellular and equiaxed Al 3 Ni precipitates in the as-printed alloy. Additionally, the rapid solidification characteristic of laser powder bed fusion created a super-saturated Zr solid solution. An aging heat treatment at 375 °C for 24 h imparted strengthening through the precipitation of L1 2 -Al 3 Zr nanoprecipitates, which counteracted the softening caused by the fragmentation and coarsening of Al 3 Ni precipitates. The yield strength increased from 138 MPa in the as-printed condition to 168 MPa after aging, while the ductility remained constant at ∼21%. The aging treatment simultaneously increased the electrical conductivity from 40.8% IACS (International Annealed Copper Standard) to 53.5% IACS. Modeling of the strengthening mechanisms and electrical conductivity contributions rationalized the simultaneous increase in strength and conductivity upon aging. Furthermore, the strengthening efficacy of the Al 3 Ni and L1 2 -Al 3 Zr precipitates, combined with the low Ni and Zr solubility in the FCC Al matrix, facilitated both high strength and electrical conductivity. Overall, the combination of strength and electrical conductivity positions this alloy as a suitable choice for additively manufactured lightweight conductors.

Additive manufacturing↗
DOE OSTI2025

Modification of Ni-20Cr corrosion dealloying behavior in molten fluorides via cold work induced plastic deformation

The corrosion dealloying behavior of cold-worked (CW) Ni20Cr alloy (wt%) was studied in molten LiF-NaF-KF (or FLiNaK) salts at 600 °C, equal to a homologous temperature (TH) of 0.52. Alloys were cold-rolled to achieve reductions of thickness of 10%, 30%, and 50% introducing plastic deformation and a high density of dislocations. Potentiostatic holds (Eapplied) were applied in two different electrode potential regimes. At 1.75VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, Cr dealloying to Cr(II) and Cr(III) is predominant, while at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, both Ni and Cr are oxidized in molten FLiNaK at 600 °C. In these potential regimes, dealloyed Ni20Cr displayed bicontinuous porosity within the grain interior and at grain boundaries, driven by the high driving force for Cr dissolution and sustained by defect mediated outward solid state diffusion of Cr in parallel with surface diffusion of Ni. The bicontinuous porous structure developed was observed to undergo further coarsening and densification of the Ni-rich ligaments at a higher electrode potential. The main effect of CW observed is the introduction of plastic deformation and dislocation substructures that serve as short-circuit paths for Cr solid state diffusion to surfaces exposed to FLiNaK. This modified the evolution of the bicontinuous porous structure which increased with CW substantially. Kinetic analysis reveals that the Cr dealloying at +1.75 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ and 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ is initially charge transfer controlled, except for the 50% CW condition at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, where the process becomes limited by slow Cr defect mediated bulk diffusion. The rate determining factors are explored and compared to experimental results.

Chan, Ho Lun↗
DOE OSTI2023

Strengthening model development and effects of low diffusing solutes to coarsening resistance in aluminum alloys

A modified Orowan strengthening model is proposed to account for finite rod-shaped precipitates with hemispherical caps in aluminum alloy systems. A combined computational and experimental approach is used to study the influences of anisotropic Orowan looping and solute-dislocation interaction on temperature-dependent yield strength. Here, the strengthening model is validated with a dataset containing 297 experimental precipitate geometries, chemistries, temperatures, and strength measurements, and achieves a strong predictive correlation of 0.8713 with experimentally measured yield strengths. Under conditions that are applicable to coarsening, constant particle volume fraction and aspect ratio, the model predicts that short rod precipitates provide far superior strengthening effects compared to plate precipitates. A cast Al-Si-Mg-Cu alloy with rod-shaped Q-phase (Al 3 Cu 2 Mg 9 Si 7 ) precipitates was developed with a novel chemistry exploring the use of low-diffusivity elements (Mn, Ni, V, Zr) to limit precipitate coarsening. The thermodynamic behavior of Mn, Ni, V, and Zr across the Q-phase interface is examined using transmission electron microscopy (TEM), first-principles density-functional theory (DFT) calculations. and atom-probe tomography (APT). DFT calculations utilizing TEM identified Q-phase/Al-matrix interfaces show that Mn, Ni, V, and Zr preferentially segregate to the Q-phase precipitate boundaries which suggests inhibition of precipitate coarsening and higher strengths after temperature exposure. Atom-probe tomography confirms solute atom partitioning/segregation at the Q-phase/Al-matrix interface, found in the modified commercial AS7GU alloy (A356 +0.5%Cu), which supports these observations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding coarsening of a post-corrosion microstructure in a molten salt by combining phase-field modeling and in situ tomography

Alloys corroding in molten salt have been observed to form bicontinuous, nanoporous microstructures via dealloying, which subsequently undergo coarsening due to facile transport in high-temperature conditions. In this work, we describe a methodology to elucidate the underlying transport mechanisms during coarsening of a bicontinuous microstructure via quantitative comparisons between phase-field simulations and four-dimensional in situ experiments, in this case X-ray nanotomography of the coarsening of a dealloyed 80 wt% Ni-20 wt% Cr microwire in molten KCl-MgCl 2 at 800°C. We conduct phase-field simulations initialized from experimental data to model coarsening via three different transport mechanisms: surface diffusion, solid bulk diffusion, and liquid bulk diffusion. These simulations reproduce key features of the experiment, such as the densification of the outer layer of the dealloyed wire and the reduction in radius over time. We quantitatively compare different microstructural characteristics between the simulations and experiment and extract temporal scaling factors that optimally match the time scales of the simulations to that of the experiment. This allows us to evaluate morphological similarity between the simulations and experiment and relate the experimental coarsening kinetics to fundamental material properties. We find that surface diffusion is most likely to be the dominant coarsening mechanism, and its kinetics imply a surface diffusivity of D S = 8.9 x 10 -20 m 3 /s, which is within the range of reported values for Ni-vacuum interfaces at 800°C. However, the difference between the experiment and the surface diffusion simulation increases substantially at late times, suggesting that other mechanisms, such as the dissolution of residual Cr, may be at play.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Morphological Evolution and Dealloying During Corrosion of Ni20Cr (wt.%) in Molten FLiNaK Salts

The dealloying corrosion behavior of the FCC Ni20Cr (wt%) in molten LiF-NaF-KF (FLiNaK) salts at 600 °C under varying applied potentials was investigated. Using in-operando electrochemical techniques and a multi-modal suite of characterization methods, we connect electrochemical potential, thermodynamic stability, and electro-dissolution kinetics to the corrosion morphologies. Notably, under certain potential regimes, a micron-scale bicontinuous structure, characterized by a network of interconnected pores and ligaments riched with the composition of the more noble (MN) element, becomes prominent. At other potentials both MN and less noble (LN) elements dealloy but at different rates. The dealloying process consists of lattice and grain boundary diffusion of Cr to the metal/salt interface, interphase Cr oxidation, accompanied by surface diffusion of Ni to form interconnected ligaments. At higher potentials, the bicontinuous porous structure undergoes further surface coarsening. Concurrently, Cr(II), Cr(III), and Ni(II) begin to dissolve, with the dissolution of Ni occurring at a significantly slower rate. When solid-state transport of Cr is exceeded by the interfacial rates, dealloying depths are limited.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Design and Characterization of Hierarchically-Strengthened, Cast Al-Ce-Ni-Mn-Sc-Zr Alloys for High-Temperature Applications

We characterize the microstructure and mechanical properties of cast Al-Ce-Ni-Mn-Sc-Zr alloys designed for structural use above 300 °C. We first report on the effect of Ni on the as-cast phase formation, where all alloys consist of fine Al11Ce3 and Ni-rich eutectic phases, but the identity of the Ni-rich phase varies with Ni content. Furthermore, these alloys contain four coarsening-resistant strengthening phases as determined from SEM and APT investigations: (i) Al11Ce3 and (ii) Ni-rich micron-scale platelets formed during eutectic solidification, (iii) L12-Al3(Sc,Zr) nanoprecipitates formed during secondary aging, and (iv) Mn solute in the α-Al matrix. The Al-Ce-Ni-Mn-Sc-Zr alloy possesses higher microhardness and creep resistance than compositionally simpler alloys containing fewer of the strengthening phases, indicating that these strengthening mechanisms synergize to provide increased ambient- and elevated-temperature strength.

Ekaputra, Clement↗
DOE OSTI2024

Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys

Enhancement of thermal stability in Al-Ni alloys through microalloying with slow-diffusing elements, specifically Zr, has been previously reported which is attributed to Zr segregation at the Al/Al 3 Ni interface. In this study, we explore the influence of microalloying Al-Ni alloys with Zr, Ti, V, and Fe on microstructural evolution, hardness, and electrical and thermal conductivity across a range of heat-treatment temperatures from 300 to 450 °C. The distribution of microalloying elements and precipitates after heat treatment is characterized using atom probe tomography (APT). Our investigation confirms Zr segregation to the Al/Al 3 Ni interface, while similar interfacial segregation is absent with the addition of Ti, V, and Fe. Additionally, our analysis of the Al 3 Ni microfiber morphology reveals that their coarsening and spheroidization rates are similar with and without interfacial segregation; thus, retaining the fiber reinforcement through interfacial segregation of slow diffusing elements may not be an effective strategy. Precipitation of L1 2 nanoparticles was found to be the dominant mechanism affecting enhanced hardness and electrical conductivity in Al-Ni-Zr alloys, attributed to precipitation strengthening and solute depletion, respectively. Similar precipitation was not observed for additions of Ti, V, and Fe following heat treatment. We provide a thermodynamic explanation for this limitation. Furthermore, the findings of this study suggest that an effective approach for designing Al-Ni alloys should involve prioritizing microalloying elements to maximize L1 2 precipitation and minimize solute content in the FCC-Al matrix post heat treatment, rather than focusing on Al/Al3Ni interfacial segregation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Co-, Ni- and Fe-rich grain-boundary phases enhance creep resistance in θ'-strengthened Al-Cu alloys

Here, microstructural evolution and creep response were investigated in the cast Al-5.0Cu-0.3Mn-0.2Zr (wt.%) alloy with and without addition of slow-diffusing, intermetallic-forming elements Fe, Ni, or Co. Baseline Al-5.0Cu-0.3Mn-0.2Zr alloy exhibits high creep resistance at 300 °C, up to ~75 MPa, which is attributed to high-aspect-ratio, intragranular θ'-Al 2 Cu precipitates that effectively suppress dislocation climb. However, θ'-Al 2 Cu precipitate-free zones form along grain boundaries upon heat treatment, whose extent is amplified during subsequent creep. Such weak regions experience dislocation creep, leading to strain localization and acceleration of grain-boundary sliding. Adding Ni and Co, individually or in combination, leads to the formation of grain-boundary precipitates (Al 9 Co 2 , Al 3 Ni 2 ) which are resistant to coarsening, thus suppressing the formation of θ'-Al 2 Cu precipitate-free zones. This microstructure provides high creep resistance at stresses up to 75–80 MPa, with strain rates much lower than in unmodified Al-5.0Cu-0.3Mn-0.2Zr. Adding Fe, which results in extensive decoration of grain boundaries with coarsening-resistant Al 7 Cu 2 Fe, and then increasing the Cu content to compensate for the Cu loss to this new phase, leads to a new Al-7.4Cu-1.6Fe-0.3Mn-0.2Zr alloy with creep resistance at 300 °C that surpasses known cast aluminum alloys. Adding Fe to improve the creep resistance of Al-Cu alloys is both cost-effective and sustainable. Our findings offer guidelines applicable to various alloy systems on controlling the evolution of precipitate-free zones and its ensuing effects on creep deformation.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Thoria stability in TD-NiCr at high temperatures in the presence of chromium in solution.

Study of the influence of chromium in solid solution on the coarsening of ThO2 in TD-NiCr. Comparisons were made of ThO2 coarsening in chromium-free TD-Ni and in TD-NiCr, which is known to be low in Cr2O3 as a contaminant. The results of these comparisons indicate that the presence of 20% Cr in solid solution in a nickel-base alloy does not lead to a more rapid coarsening of ThO2 at temperatures of at least 2462 deg F (1350 deg C).

Dalal, H.↗
DOE OSTI2022

A creep-resistant additively manufactured Al-Ce-Ni-Mn alloy

Existing additively manufactured aluminum alloys exhibit poor creep resistance due to coarsening of their strengthening phases and refined grain structures. In this paper, we report on a novel additively manufactured Al-10.5Ce-3.1Ni-1.2Mn wt.% alloy which displays excellent creep resistance relative to cast high-temperature aluminum alloys at 300–400 °C. In this work, the creep resistance of this alloy is attributed to a high volume fraction (~35%) of submicron intermetallic strengthening phases which are coarsening-resistant for hundreds of hours at 350 °C. The results herein demonstrate that additive manufacturing provides opportunities for development of creep-resistant aluminum alloys that may be used in bulk form in the 250–400 °C temperature range. Pathways for further development of such alloys are identified.

36 MATERIALS SCIENCE↗
NASA NTRS2009

Effects of Tantalum on the Temporal Evolution of a Model Ni-Al-Cr Superalloy During Phase Decomposition

The effects of a 2.0 at.% addition of Ta to a model Ni-10.0Al-8.5Cr (at.%) superalloy aged at 1073 K are assessed using scanning electron microscopy and atom-probe tomography. The gamma'(Ll2)-precipitate morphology that develops as a result of gamma-(fcc)matrix phase decomposition is found to evolve from a bimodal distribution of spheroidal precipitates, to {001}-faceted cuboids and parallelepipeds aligned along the elastically soft {001}-type directions. The phase compositions and the widths of the gamma'-precipitate/gamma-matrix heterophase interfaces evolve temporally as the Ni-Al-Cr-Ta alloy undergoes quasi-stationary state coarsening after 1 h of aging. Tantalum is observed to partition preferentially to the gamma'-precipitate phase, and suppresses the mobility of Ni in the gamma-matrix sufficiently to cause an accumulation of Ni on the gamma-matrix side of the gamma'/gamma interface. Additionally, computational modeling, employing Thermo-Calc, Dictra and PrecipiCalc, is employed to elucidate the kinetic pathways that lead to phase decomposition in this concentrated Ni-Al-Cr-Ta alloy.

Booth, Morrison, Christopher↗
DOE OSTI2023

Nanocluster Evolution in D9 Austenitic Steel under Neutron and Proton Irradiation

Austenitic stainless steel D9 is a candidate for Generation IV nuclear reactor structural materials due to its enhanced irradiation tolerance and high-temperature creep strength compared to conventional 300-series stainless steels. But, like other austenitic steels, D9 is susceptible to irradiation-induced clustering of Ni and Si, the mechanism for which is not well understood. This study utilizes atom probe tomography (APT) to characterize the chemistry and morphology of Ni–Si nanoclusters in D9 following neutron or proton irradiation to doses ranging from 5–9 displacements per atom (dpa) and temperatures ranging from 430–683 °C. Nanoclusters form only after neutron irradiation and exhibit classical coarsening with increasing dose and temperature. The nanoclusters have Ni 3 Si stoichiometry in a Ni core–Si shell structure. This core–shell structure provides insight into a potentially unique nucleation and growth mechanism—nanocluster cores may nucleate through local, spinodal-like compositional fluctuations in Ni, with subsequent growth driven by rapid Si diffusion. This study underscores how APT can shed light on an unusual irradiation-induced nanocluster nucleation mechanism active in the ubiquitous class of austenitic stainless steels.

36 MATERIALS SCIENCE↗
NASA NTRS1983

The development of directional coarsening of the gamma-prime precipitate in superalloy single crystals

A study has been made of the kinetics of the directional coarsening of the gamma-prime precipitates in Ni-5.8Al-14.6Mo-6.2Ta single crystals during creep at 982 C. In this alloy, which is characterized by a large negative lattice misfit between the gamma-prime precipitate and the gamma matrix, the formation of gamma-prime rafts begins during primary creep, and the rafts grow in length as the deformation proceeds into steady-state creep. After that, the length of the rafts stabilizes. The thickness of the rafts remains constant from primary up to tertiary creep. The directional coarsening behavior of the alloy studied is similar to that of a more conventional single-crystal superalloy having a substantially smaller negative misfit.

Mackay, R. A.↗