Search NASA⌕ Search

SEARCH · Search NASA

Results for “Noise Abatement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Engineering simulation evaluation of the two-segment noise abatement approach in the Douglas DC-8-61

The development and operational evaluation are discussed of a noise abatement two-segment approach which is safe and operationally acceptable for routine use in air carrier service. An engineering simulation evaluation was conducted; it was found that the entry speed and initial configuration are more important in the DC-8-61 than in the 727 because of the DC-8's aerodynamic cleanliness and drag programming constraints. It was also found that the altitude required for the DC-8 upper and lower transitions is less than the 727 transitions principally due to the pitching moment from the underslung DC-8 engines as compared to the 727 engines which produce no pitching moment with a change in thrust. The 727 approach was a reduced flaps (30 degrees) procedure with a 10-knot airspeed bleed in the lower transition; the DC-8 approach is a full flaps (50 degrees) procedure with constant airspeed established as soon as possible after upper segment transition.

Nylen, W. E.↗
NASA NTRS1972

A comparison of optimal and noise-abatement trajectories of a tilt-rotor aircraft

The potential benefits of flight path control to optimize performance and/or reduce the noise of a tilt-rotor aircraft operating in the takeoff and landing phases of flight are investigated. A theoretical performance-acoustic model is developed and then mathematically flown to yield representative takeoff and landing profiles. Minimum-time and minimum-fuel trajectories are compared to proposed noise-abatement profiles to assess the reductions in annoyance possible through flight path control. Significant reductions are feasible if a nearly vertical-takeoff flight profile is flown near the landing site; however, the time expended and fuel consumed increase.

Schmitz, F. H.↗
NASA NTRS1972

Flight evaluation of three-dimensional area navigation for jet transport noise abatement.

The NASA, working with American Airlines, has completed the first phase of research to evaluate the operational feasibility of two-segment approaches for noise abatement. For these tests, area navigation was used to establish the upper glide slope and an ILS was used to establish the lower. The flight director was modified to provide command information during the entire approach. Twenty-eight pilots representing the airlines, professional pilot associations, FAA, and NASA participated. With an ILS approach for comparison, the procedure gave a noise reduction of 18 EPNdB at the outer marker and 8 EPNdB 1.1 n. mi. from touchdown.

Denery, D. G.↗
NASA NTRS1995

Acoustic flight tests of rotorcraft noise-abatement approaches using local differential GPS guidance

This paper presents the test design, instrumentation set-up, data acquisition, and the results of an acoustic flight experiment to study how noise due to blade-vortex interaction (BVI) may be alleviated. The flight experiment was conducted using the NASA/Army Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) research helicopter. A Local Differential Global Positioning System (LDGPS) was used for precision navigation and cockpit display guidance. A laser-based rotor state measurement system on board the aircraft was used to measure the main rotor tip-path-plane angle-of-attack. Tests were performed at Crows Landing Airfield in northern California with an array of microphones similar to that used in the standard ICAO/FAA noise certification test. The methodology used in the design of a RASCAL-specific, multi-segment, decelerating approach profile for BVI noise abatement is described, and the flight data pertaining to the flight technical errors and the acoustic data for assessing the noise reduction effectiveness are reported.

Chen, Robert T. N.↗
NASA NTRS1973

A study to determine the applicability of noise abatement approach procedures to McDonnell Douglas Aircraft

Analyses of McDonnell Douglas DC-8, DC-9, and DC-10 jet transports were conducted to investigate the applicability of two segment approach noise abatement procedures to these airplanes. All models had the required glide slope capability at the certified landing flap settings. The DC-8 models would probably be limited to an upper segment glide slope of 5.5 degrees and would probably not be suitable for the two segment procedure in icing conditions. The DC-8 would not be compatible with this procedure at a reduced landing flap setting. The feasibility of installing a two segment approach system in the Douglas-built fleet of commercial jet transports from a hardware viewpoint is discussed. The candidate system consists of a two segment computer plus the necessary peripheral equipment interfaced with the existing autopilot and associated avionics. The required modifications and additions to existing equipment are described and the attendant costs estimated. Potential problems which may be encountered are also discussed.

Painter, J. A.↗
NASA NTRS1983

Noise Abatement

SMART, Sound Modification and Regulated Temperature compound, is a liquid plastic mixture with exceptional energy and sound absorbing qualities. It is derived from a very elastic plastic which was an effective noise abatement material in the Apollo Guidance System. Discovered by a NASA employee, it is marketed by Environmental Health Systems, Inc. (EHS). The product has been successfully employed by a diaper company with noisy dryers and a sugar company with noisy blowers. The company also manufactures an audiometric test booth and acoustical office partitions.

Source record↗
NASA NTRSDate not supplied

Medium-Sized Helicopter Noise Abatement Flight Test

An extensive flight test campaign was recently completed which aims to reduce the noise generated by helicopters in an effort to improve community acceptance. Using a ground-based microphone array, acoustic measurements were acquired on helicopters in the medium-size vehicle weight class over a number of flight conditions including steady level flight, steady descents, and approaches. While data were collected across four helicopters, the Leonardo AW139 and Sikorsky S-76D will be the focus of this paper. The extent of measured ground noise con- tours was limited due to the site constraints. Thus, the Noise Informed Community Environment Operations Planning System (NICEOPS) in conjunction with the flight test data was used to estimate how changes in the operating procedures impact noise exposure over a wider area during approaches. It was found that even small longitudinal accelerations can have a substantial influence on the noise generation processes during approach and must be modeled appropriately to develop new flight procedures which minimize the acoustic impact on the ground.

Flight Testing↗
NASA NTRSDate not supplied

Development and Validation of Generic Maneuvering Flight Noise Abatement Guidance for Helicopters

An extensive flight test campaign has been conducted to look into developing actionable advice for pilots of today’s vehicles to reduce their acoustic footprints. Ten distinct vehicles were tested at three different test ranges, with nine of the vehicles’ data being documented here. Twelve pairs of turning conditions were tested to determine their effect on blade-vortex interaction noise. Each turning flight condition was evaluated using the peak A-weighted, band-limited (50 Hz - 2500 Hz), sound pressure level measured throughout the maneuver. This metric was a surrogate for blade-vortex interaction noise, and the difference between the peak values of each turning pair was investigated. That peak value difference was subsequently corrected by the offset from the intended vehicle altitude at turn initiation from the actual altitude at initiation. The corrected amplitudes were investigated and grouped into six validated actionable guidance principles that can be given to pilots to immediately reduce their acoustic footprint during operations.

Flight Test↗
NASA NTRS1976

Business jet approach noise abatement techniques - Flight test results

Operational techniques for reducing approach noise from business jet aircraft were evaluated in flight by measuring the noise generated by five such aircraft during modified approaches. Approaches with 4-deg glide slopes were approximately 4.0 EPNdB quieter than approaches with standard 3-deg glide slopes. Noise reductions for low-drag 3-deg approaches varied widely among the airplanes tested; the fleet-weighted reduction was 8.5 EPNdB. Two-segment approaches resulted in noise reductions of 7.0 EPNdB to 8.5 EPNdB 3 nautical miles and 5 nautical miles from touchdown. Pilot workload increased progressively for the 4-deg, low-drag 3-deg, and two-segment approach.

Putnam, T. W.↗
NASA NTRS2015

An Assessment of Flap and Main Landing Gear Noise Abatement Concepts

A detailed assessment of the acoustic performance of several noise reduction concepts for aircraft flaps and landing gear is presented. Consideration is given to the best performing concepts within the suite of technologies that were evaluated in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel using an 18 percent scale, semi-span, high-fidelity Gulfstream aircraft model as a test bed. Microphone array measurements were obtained with the model in a landing configuration (flap deflected 39 degrees and the main landing gear deployed or retracted). The effectiveness of each concept over the range of pitch angles, speeds, and directivity angles tested is presented. Comparison of the acoustic spectra, obtained from integration of the beamform maps between the untreated baseline and treated configurations, clearly demonstrates that the flap and gear concepts maintain noise reduction benefits over the entire range of the directivity angles tested.

Khorrami, Mehdi R.↗
NASA NTRS1980

Transport jet aircraft noise abatement in foreign countries: Growth, structure, impact. Volume 2: Pacific basin, August 1980

Noise control measures at the international airports of Hawaii, New Zealand, Australia, Hong Kong, Japan, and Singapore were studied. Factors in noise control, such as government structure are examined. The increasing power of environmental agencies vis-a-vis aviation departments is noted. The following methods of dealing with aircraft noise are examined by type of control: noise at the source control; noise emmission controls, zoning, building codes, subsidies for relocation, insulation, loss in property values, and for TV, radio and telephone interference; and noise-related landing charges.

Spencer, F. A.↗
NASA NTRS2000

Rotorcraft Noise Abatement Flight Path Modeling

This report addresses development of a rotor state/trim modeling capability for noise modeling of decelerating rotorcraft approaches. The resulting technique employs discretization of the descent trajectory as multiple steady state segments for input to CAMRAD.Mod 1 to predict rotor states for acoustic analysis. Deceleration is included by modifying the CAMRAD.Mod 1 free flight trim options to allow trim to the specified acceleration/deceleration components.

Murty, Hema↗
NASA NTRS1975

Preliminary core-engine noise abatement experimental results of a fluid injection nozzle on a JT-15D turbofan engine

Jet noise, as induced by shear stress, in an jet exhaust is investigated. Experiments were performed on a JT-15D fan jet to verify the inward momentum stress reduction concept. The experiments involved making fan air flow convergently around the high velocity core jet with a small angle. Ring airfoils were used as flow separators for the minimization of the thrust loss. Jet exhaust noise reduction of ll db at 30 deg from the jet axis was recorded and 8 db integrated overall noise reduction over a hemisphere was measured with only 4.6% thrust loss, or 152 db/percent thrust loss.

Cheng, D. Y.↗
NASA NTRS1980

Transport jet aircraft noise abatement in foreign countries: Growth, structure, impact. Volume 1: Europe, July 1980

The development and implementation of aircraft noise control regulations in various European states are described. The countries include the United Kingdom, France, Switzerland, Federal Republic of Germany, Sweden, Denmark, and the Netherlands. Topics discussed include noise monitoring, airport curfews, land use planning, and the government structure for noise regulation.

Spencer, F. A.↗
NASA NTRS1974

Engineering simulation development and evaluation of the two-segment noise abatement approach conducted in the B-727-222 flight simulator

Profile modification as a means of reducing ground level noise from jet aircraft in the landing approach is evaluated. A flight simulator was modified to incorporate the cockpit hardware which would be in the prototype airplane installation. The two-segment system operational and aircraft interface logic was accurately emulated in software. Programs were developed to permit data to be recorded in real time on the line printer, a 14-channel oscillograph, and an x-y plotter. The two-segment profile and procedures which were developed are described with emphasis on operational concepts and constraints. The two-segment system operational logic and the flight simulator capabilities are described. The findings influenced the ultimate system design and aircraft interface.

Nylen, W. E.↗