Results for “OPTICAL EMISSION SPECTROSCOPY” — Page 2

NASA NTRS1990

Electron cyclotron resonance deposition of diamond-like films

Electron cyclotron resonance (ECR) microwave plasma CVD has been developed at low pressures (0.0001 - 0.01 torr) and at ambient and high substrate temperatures (up to 750 C), to achieve large-area (greater than 4 in. diameter) depositions of diamondlike amorphous carbon (a - C:H) films. The application of a RF bias to the substrate stage, which induces a negative self-bias voltage, is found to play a critical role in determining carbon bonding configurations and in modifying the film morphology. There are two distinct types of ECR-deposited diamondlike films. One type of diamondlike film exhibits a Raman spectrum consisting of broad and overlapping, graphitic D (1360/cm, line width = 280/cm) and G (1590/cm, line width 140/cm) lines, and the other type has a broad Raman peak centered at appoximately 1500/cm. Examination of plasma species by optical emission spectroscopy shows no correlation between the CH-asterisk emission intensity and the deposition rate of diamondklike films.

Shing, Y. H.↗

NASA NTRS2003

Mars Surveyor Program '01 Mars Environmental Compatibility Assessment wet chemistry lab: a sensor array for chemical analysis of the Martian soil

The Mars Environmental Compatibility Assessment (MECA) instrument was designed, built, and flight qualified for the now canceled MSP (Mars Surveyor Program) '01 Lander. The MECA package consisted of a microscope, electrometer, material patch plates, and a wet chemistry laboratory (WCL). The primary goal of MECA was to analyze the Martian soil (regolith) for possible hazards to future astronauts and to provide a better understanding of Martian regolith geochemistry. The purpose of the WCL was to analyze for a range of soluble ionic chemical species and electrochemical parameters. The heart of the WCL was a sensor array of electrochemically based ion-selective electrodes (ISE). After 20 months storage at -23 degrees C and subsequent extended freeze/thawing cycles, WCL sensors were evaluated to determine both their physical durability and analytical responses. A fractional factorial calibration of the sensors was used to obtain slope, intercept, and all necessary selectivity coefficients simultaneously for selected ISEs. This calibration was used to model five cation and three anion sensors. These data were subsequently used to determine concentrations of several ions in two soil leachate simulants (based on terrestrial seawater and hypothesized Mars brine) and four actual soil samples. The WCL results were compared to simulant and soil samples using ion chromatography and inductively coupled plasma optical emission spectroscopy. The results showed that flight qualification and prolonged low-temperature storage conditions had minimal effects on the sensors. In addition, the analytical optimization method provided quantitative and qualitative data that could be used to accurately identify the chemical composition of the simulants and soils. The WCL has the ability to provide data that can be used to "read" the chemical, geological, and climatic history of Mars, as well as the potential habitability of its regolith.

Non-NASA Center↗

NASA NTRS2009

Characterization of a Plasmoid in the Afterglow of a Supersonic Flowing Microwave Discharge

We performed a detailed characterization a plasmoid in the afterglow region of an Ar supersonic microwave cavity discharge. The supersonic flow was generated using a convergent-divergent nozzle upstream of the discharge region. A cylindrical cavity was used to sustain a discharge in the pressure range of 100-600 Pa. Optical emission spectroscopy was used to observe populations of excited and ionic species in the plasmoid region. Plasmoid formation in the supersonic flowing afterglow located downstream from the primary microwave cavity discharge was characterized by measuring the radial and axial distributions of Argon excited states and Argon ions. More experiments are being carried out on the plasmoid to understand the discharge parameters within the region, i.e. rotational temperature, vibrational temperature, electron density, and how the electrodynamic and aerodynamic effects combine to form this plasmoid.

Drake, D. J.↗

NASA NTRS2012

Failure Analysis of T-38 Aircraft Burst Hydraulic Aileron Return Line

During maintenance troubleshooting for fluctuating hydraulic pressures, a technician found that a right hand aileron return line, on the flight hydraulic side, was ruptured (Fig. 1, 2). This tubing is part of the Hydraulic Flight Control Aileron Return Reducer to Aileron Manifold and is suspected to be original to the T-38 Talon trainer aircraft. Ailerons are small hinged sections on the outboard portion of a wing used to generate rolling motion thereby banking the aircraft. The ailerons work by changing the effective shape of the airfoil of the outer portion of the wing [1]. The drawing, Northrop P/N 3-43033-55 (6/1960), specifies that the line is made from 0.375 inch OD, aluminum 5052-0 tubing with a 0.049 inch wall thickness. WW-T-787 requires the tube shall be seamless and uniform in quality and temper [2]. The test pressure for this line is 3000 psi, and the operational pressure for this line is estimated to be between 45 psi and 1500 psi based on dynamic loading during flight. Examination of the fracture surface found evidence of arrest bands originating on the inner diameter (Fig 3). Ductile dimples are observed on the tube fractures (Fig. 4). The etched cross-section revealed thinning and work-hardening in the burst region (Fig. 5). The wall thickness just outside the work-hardened fracture region measured 0.035". Barlow's Formula: P = 2St/D, where P is burst pressure, S is allowable stress, t is wall thickness and D is the outer diameter of tube. Using the ultimate tensile strength of 28 ksi and a measured wall thickness of 0.035 inches at burst, P = 5.2 ksi (burst pressure). Using the yield of 13 ksi (YS) for aluminum 5052-0, plastic deformation will happen at P = 2.4 ksi suggesting plastic deformation occurred at a proof pressure of 3.0 ksi. Conclusion: The burst resulted from high stress, low-cycle fatigue. Evidence of arrest bands originating on the inner diameter. Fracture is predominately shear dimples, characteristic of high load ductile fractures (Fig 6). Section wall reduction in the burst region. Plastic deformation and thinning of the out-of-specification tube wall likely happened during the initial proof testing years ago. Metallography of tubing away from rupture site confirmed tubing was seamless. Based on the tube microstructure, it is likely that the initial wall thickness was about 30 % thinner than the requirement of 0.049 inches. Fracture initiated on the ID and progressed to the OD (shear lip). The tube is made of the correct material of 5052-0 aluminum as verified using Optical Emission Spectroscopy (Table 2). The tubing hardness tested 77 HV100 (77 HRE). This hardness is slightly above the requirement for 70 HRE maximum for aluminum 5052-0 in AMS 2658C [3].

Martinez, J. E.↗

NASA NTRS2013

Optical Emission Characterization of High-Power Hall Thruster Wear

Optical emission spectroscopy is employed to correlate BN insulator erosion with high-power operation of the NASA 300M Hall-effect thruster. Actinometry leveraging excited xenon states is used to normalize the emission spectra of ground state boron as a function of thruster operating condition. Trends in the strength of the boron signal are correlated with thruster power, discharge voltage, discharge current and magnetic field strength. The boron signals are shown to trend with discharge current and show weak dependence on discharge voltage. The trends are consistent with data previously collected on the NASA 300M and NASA 457M thrusters but are different from conventional wisdom.

WIlliams, George J.↗

NASA NTRS2014

High Current Hollow Cathode Plasma Plume Measurements

Plasma plume measurements are reported for a hollow cathode assembly (HCA) operated at discharge currents of 50, 70, and 100 A at xenon flow rates between 19 - 46 standard cubic centimeter per minute. The HCA was centrally mounted in the NASA-300MS Hall Thruster and was operated in the "spot" and "plume" modes with additional data taken with an applied magnetic field. Langmuir probes, retarding potential analyzers, and optical emission spectroscopy were employed to measure plasma properties near the orifice of the HCA and to assess the charge state of the near-field plasma. Electron temperatures (2-6 electron volt) and plasma potentials are consistent with probe-measured values in previous investigations. Operation with an applied-field yields higher discharge voltages, increased Xe III production, and increased signals from the 833.5 nm C I line. While operating in plume mode and with an applied field, ion energy distribution measurements yield ions with energies significantly exceeding the applied discharge voltage. These findings are correlated with high-frequency oscillations associated with each mode.

High frequency analysis↗

NASA NTRS2016

Characterization of Low Pressure Cold Plasma in the Cleaning of Contaminated Surfaces

The characterization of low pressure cold plasma is a broad topic which would benefit many different applications involving such plasma. The characterization described in this paper focuses on cold plasma used as a medium in cleaning and disinfection applications. Optical Emission Spectroscopy (OES) and Mass Spectrometry (MS) are the two analytical methods used in this paper to characterize the plasma. OES analyzes molecules in the plasma phase by displaying the light emitted by the plasma molecules on a graph of wavelength vs. intensity. OES was most useful in identifying species which may interact with other molecules in the plasma, such as atomic oxygen or hydroxide radicals. Extracting useful data from the MS is done by filtering out the peaks generated by expected molecules and looking for peaks caused by foreign ones leaving the plasma chamber. This paper describes the efforts at setting up and testing these methods in order to accurately and effectively characterize the plasma.

cold plasma characterization↗

NASA NTRSDate not supplied

Hydrogen Plasma Reduction of Silicates for Lunar Oxygen Liberation

As crewed missions to the moon become closer, the focus on in-situ resource utilization efforts has increased. Since lunar soil has abundant oxygen on the surface of the moon, work has been done to process this resource in an efficient manner. Hydrogen reduction of lunar regolith has emerged as a method of liberating oxygen that can be used for fuel and water production. Traditional reduction techniques require high temperatures and increased complexity when dealing with high amounts of silicates. Plasma can reduce silicates efficiently and thus has become of high interest for use in the lunar highlands where silicates exist in high quantities. NASA’s Kennedy Space Center is exploring the use of low temperature plasmas for the reduction of silicates. This work shows that exposing silicates to a hydrogen plasma produces water. Residual gas analysis and optical emission spectroscopy were used to measure the relative quantities of water vapor production and OH (A-X) emission for hydrogen plasma interactions with lunar highland simulant and silica. X-ray photo-electron spectroscopy and scanning electron microscopy/energy-dispersive X-ray spectroscopy were also used to observe surface modifications to the silicates that reflect the key chemical reactions that occurred. From this data, plasma has emerged as a promising solution to produce oxygen on the lunar surface. *Work supported by NASA's Science Technology Mission Directorate Center Innovation Fund.

R. P. Gott↗

NASA NTRSDate not supplied

Plasma Reduction of Regolith for Oxygen Liberation

As crewed missions to the moon become closer, the focus on in-situ resource utilization efforts has increased. Since lunar soil has abundant oxygen on the surface of the moon, work has been done to process this resource in an efficient manner. Hydrogen reduction of lunar regolith has emerged as a method of liberating oxygen that can be used for fuel and water production. Traditional reduction techniques require high temperatures and increased complexity when dealing with high amounts of silicates. Plasma can reduce silicates efficiently and thus has become of high interest for use in the lunar highlands where silicates exist in high quantities. NASA’s Kennedy Space Center is exploring the use of low temperature plasmas for the reduction of silicates. This work shows that exposing silicates to a hydrogen plasma produces water. Residual gas analysis and optical emission spectroscopy were used to measure the relative quantities of water vapor production and OH (A-X) emission for hydrogen plasma interactions with lunar highland simulant and silica. X-ray photo-electron spectroscopy and scanning electron microscopy/energy-dispersive X-ray spectroscopy were also used to observe surface modifications to the silicates that reflect the key chemical reactions that occurred. From this data, plasma has emerged as a promising solution to produce oxygen on the lunar surface.

Ryan Gott↗

NASA NTRS2022

Shock Tube Radiation Measurement in Expanding Air Flow

The EAST facility has been widely used in the past to provide experimental data aiming to validate radiative heating models. However, all the past studies involved measurements of compressing flows. In order to study recombining flows, an expansion cone has been installed in the EAST facility. Four spectrometers are mounted at different axial positions of the cone to measure the evolution of the radiation during expansion. Quantitative data from optical emission spectroscopy will be used to get the densities of radiative species. These data are intended to be compared with simulations in order to improve the current models used by the entry community.

Augustin Tibere-Inglesse↗

NASA NTRS2022

Shock Tube Radiation Measurement in Expanding Air Flows

The EAST facility has been widely used in the past to provide experimental data aiming to validate radiative heating models. However, all the past studies involved measurements of compressing flows. In order to study recombining flows, an expansion cone has been installed in the EAST facility. Four spectrometers are mounted at different axial positions of the cone to measure the evolution of the radiation during expansion. Quantitative data from optical emission spectroscopy will be used to get the densities of radiative species. These data are intended to be compared with simulations in order to improve the current models used by the entry community.

Augustin Tibère-Inglesse↗

NASA NTRSDate not supplied

The Material Response of PICA-NuSil to a Hypersonic Flow Environment

Phenolic Impregnated Carbon Ablator (PICA) is NASA’s baseline thermal protection system for missions to Mars. PICA is friable; therefore, NuSil ® CV-1144-0 is applied to the surface of flight hardware to mitigate the contamination of spacecraft sensors. NuSil is composed of a polysiloxane resin system that can transform into an oxidation-resistant coating upon heating. Therefore, a pathfinder campaign was conducted at the Hypersonic Materials Environmental Test System (HyMETS) at the NASA Langley Research Center to investigate the material response of instrumented sphere-cone models made from PICA coated with NuSil ® . Analysis of the post-test data is presented and suggests that NuSil ® impacts the material response of test articles subjected to oxidizing atmospheres, as evidenced by a reduction of the measured surface temperature and in-depth temperature response. Finally, a four-step ablation mechanism is proposed based on observations from high-speed video, optical emission spectroscopy, thermal analysis, and post-test surface characterization.

PICA PICA-NuSil Siloxane Silicone↗

NASA NTRSDate not supplied

Development of Langmuir and Spatially Resolved OES Diagnostics for Arc Jet Shock and Boundary Layer Measurements Relevant to Atmospheric Re-Entry Environments

The second-generation miniature Arc Jet Research Chamber (mARC) ground testing facility at NASA Ames requires physical characterization of its supersonic plasma flow to verify numerical models and material sample testing. Two types of plasma diagnostics will be utilized: Langmuir probes and optical emission spectroscopy (OES). Several single and triple Langmuir probes have been constructed and will be inserted parallel to the flow via a sweep arm to measure post-shock electron temperature and number density along radial profiles at different axial distances. Due to the high heat flux (200-3000 W/cm2) sweep durations are necessarily short (< 0.1 s). Measuring these properties near the probe surface provide characterization of the post-shock environment. This is an important metric for validating coupled CFD-material codes, and will provide insight into longstanding thermocouple anomalies attributed to charging of heatshield surfaces. An OES system has also been assembled to obtain spatially resolved density and temperature for various flow species. The system consists of a convex lens that forms an image of the plasma onto a 16-channel linear fiber array, which will simultaneously capture the spectra from sixteen different locations. The light emission from the plasma is then focused by a spherical mirror into a spectrometer and recorded with a camera. These measurements non-intrusively provide a new spatially resolved flow characterization capability. This will initially be used to resolve issues with shock radiation interference in pyrometer measurements of material surface temperature. The design of each diagnostic and any initial results will be discussed.

Ethan Main-Loam Leong↗

NASA NTRSDate not supplied

The Characterization of a DC Glow Discharge in a Tripped Hypersonic Boundary Layer

A direct current glow discharge plasma was generated on a canonical 2.75° half-angle wedge test article. Experiments were conducted in the Texas A&M University Actively Controlled Expansion tunnel at 𝑀 = 5.7 and 𝑅𝑒 = 6 × 10 6 /m. The effect of Reynolds number, polarity, and upstream perturbation were all independently studied via imaging, power measurements, and optical emission spectroscopy (OES). These measurements are the first to be conducted in a tripped hypersonic boundary layer and allow a deeper understanding of the electrohydrodynamics. The plasma, formally characterized as a normal glow discharge, had negligible Joule and cathode heating effects on the boundary layer. Analogously, the installation of trips upstream of the electrodes changed only the appearance of the plasma, creating periodic streaks corresponding to the wakes and vortices produced by each trip but not altering the power across the electrodes. The plasma power peaked at 47 W, which OES revealed was sufficient to generate NO in the positive column and negative glow.

Casey J. Broslawski↗

NASA NTRSDate not supplied

The Characterization of a DC Glow Discharge in a Tripped Hypersonic Boundary Layer

A direct current glow discharge plasma was generated on a canonical 2.75° half-angle wedge test article. Experiments were conducted in the Texas A&M University Actively Controlled Expansion tunnel at 𝑀 = 5.7 and 𝑅𝑒 = 6 × 10 6 /m. The effect of Reynolds number, polarity, and upstream perturbation were all independently studied via imaging, power measurements, and optical emission spectroscopy (OES). These measurements are the first to be conducted in a tripped hypersonic boundary layer and allow a deeper understanding of the electrohydrodynamics. The plasma, formally characterized as a normal glow discharge, had negligible Joule and cathode heating effects on the boundary layer. Analogously, the installation of trips upstream of the electrodes changed only the appearance of the plasma, creating periodic streaks corresponding to the wakes and vortices produced by each trip but not altering the power across the electrodes. The plasma power peaked at 47 W, which OES revealed was sufficient to generate NO in the positive column and negative glow.

Casey Broslawski↗

NASA NTRSDate not supplied

Characterization of Titan Entry Radiative Heating in the Low Density Electric Arc Shock Tube

Prediction of aftbody radiative heating for Dragonfly’s entry at Titan requires accurate models to inform the design of its thermal protection systems. Previously reported investigations of shock layer aftbody radiation in the Electric Arc Shock Tube (EAST) at NASA Ames Research Center focused on the lower altitude/higher density part of the trajectory. This paper presents the first optical emission spectroscopy measurements of an ongoing test series in the new aluminum Low Density Shock Tube (LDST), recently installed at EAST, focusing on the radiative heating characterization through the higher altitude portion of Dragonfly’s entry path. Experimental data collected at a fill pressure of 0.1 Torr and shock velocities between 5.2 and 6.2 km/s show favorable agreement to similar conditions previously tested in the 4" High-Velocity Shock Tube, as well as improvements in the signal to noise ratio and available test time. Simulations employing DPLR and NEQAIR underpredict the experimental radiance, with increasing discrepancy from the NIR towards the UV wavelength range, thus motivating further efforts in improving the current non-Boltzmann model for the CN molecule.

A Fagnani↗

NASA NTRS1994

Fiber Optic Switch For Broadband Emission Spectroscopy

Many high-temperature processes comprise large-scale phenomena. Studying spatial and temporal correlations of physical processes between several locations within characteristic scales provides desired information on macroscopic physical processes. Achieved with emission spectroscopy by use of multiple optical fibers. Simultaneous coupling of light from these fibers into single available spectrometer and/or monochromator not accomplished without added expense of two-dimensional array and increased complexity of calibration. Quasi-simultaneous coupling, while maintaining optimum alignment and maximum throughput of broadband emission, achieved by use of fiber optic multiscanner. Instrument used successfully in study of frozen-flow losses internal to flow of plasma inside nozzle of arc jet. Instrument includes two hollow disks of different sizes and stepping motor.

De Groot, Wim↗

NASA NTRS1993

Measuring Weld Parameters By Spectroscopy

Optical-emission spectrometric apparatus used to monitor variable-polarity plasma arc welding of aluminum alloys. Spectrometer incorporated into control system to ensure quality of weld because in keyhole, arc fully penetrates weld joint and impurities flushed out. Apparatus helps ensure high quality of weld by monitoring such contaminants as oxygen and hydrogen in shield gas, detecting inadequate flow of shield gas, and sensing changes in temperature of arc with changes in arc current and voltage.

Nunes, Arthur↗