Search NASA⌕ Search

SEARCH · Search NASA

Results for “OSCILLATING CYLINDER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Mass transfer from a circular cylinder: Effects of flow unsteadiness and slight nonuniformities

Experiments were performed to determine the effect of periodic variations in the angle of the flow incident to a turbine blade on its leading edge heat load. To model this situation, measurements were made on a circular cylinder oscillating rotationally in a uniform steady flow. A naphthalene mass transfer technique was developed and used in the experiments and heat transfer rates are inferred from the results. The investigation consisted of two parts. In the first, a stationary cylinder was used and the transfer rate was measured for Re = 75,000 to 110,000 and turbulence levels from .34 percent to 4.9 percent. Comparisons with both theory and the results of others demonstrate that the accuracy and repeatability of the developed mass transfer technique is about + or - 2 percent, a large improvement over similar methods. In the second part identical flow conditions were used but the cylinder was oscillated. A Strouhal number range from .0071 to .1406 was covered. Comparisons of the unsteady and steady results indicate that the magnitude of the effect of oscillation is small and dependent on the incident turbulence conditions.

Marziale, M. L.↗
DOE OSTI2020

Synergistic Flow-Induced Oscillation of Multiple Cylinders in Harvesting Marine Hydrokinetic Energy

Abstract Flow-induced oscillations/vibrations (FIO/V) of cylinders in tandem can be enhanced by proper in-flow spacing to increase hydrokinetic energy harnessing. In a farm of multiple cylinders in tandem, the effect of interference on harnessing efficiency arises. Three years of systematic experiments in the Marine Renewable Laboratory (MRELab) of the University of Michigan, on an isolated cylinder, and two and three cylinders in tandem have revealed that synergistic FIO can enhance oscillations of cylinders in close proximity. Two cylinders in tandem can harness 2.5–13.5 times the hydrokinetic power of one isolated cylinder. Three cylinders in tandem can harness 3.4–26.4 times the hydrokinetic power of one isolated cylinder. Negative impact on the harnessed energy by multiple cylinders, such as the shielding effect for the downstream cylinder/s, is possible. Specifically for the three-cylinder configuration, at a certain flow speed, the decrease in the power of the middle cylinder can be overcome by adjusting its stiffness and/or damping.

Engineering↗
DOE OSTI2020

Flow-induced oscillation patterns for two tandem cylinders with turbulence stimulation and variable stiffness and damping

Herein, the oscillation patterns of two 1-DOF cylinder oscillators, undergoing VIV and galloping, are investigated in a free surface water channel for 3.2 × 104 ≤ Re ≤ 1.2 × 10 5 . The cylinders are arranged in tandem and supported by springs for a range of different spring stiffness and damping parameters. The efficiency of a current energy converter (CEC), based on flow-induced oscillation (FIO) of multiple cylinders in tandem, is critically related to the cylinder oscillation patterns. Due to the limited number of studies on the FIO for multiple cylindrical or prismatic bodies, their oscillation patterns have neither been identified nor classified. The surfaces of the cylinders are modified by turbulence stimulation to enhance FIO. Three different center-to-center spacing, five stiffness, and six damping ratios, for a total of 90 sets of experiments were conducted. The current velocity range is from 0.34 m/s to 1.32 m/s. From more than 2000 tests, five major patterns, nine sub-patterns are identified and classified. The patterns are defined based on the amplitudes, frequencies and the phase angle differences between the two cylinders. The characteristics and mechanics of each oscillation pattern are explored and explained from the perspective of fluid-structure interaction (FSI). By systematically varying the parameters, the underlying hydrodynamic mechanisms, including the coupling level between vortices and cylinders, the shielding effect, the wake effect, and the stability states are revealed. Few preliminary observations on the connection between oscillation pattern and harnessed power by the tandem cylinders are reported.

42 ENGINEERING↗
DOE OSTI2021

Modelling of a Flow-Induced Oscillation, Two-Cylinder, Hydrokinetic Energy Converter Based on Experimental Data

The VIVACE Converter consists of cylindrical oscillators in tandem subjected to transverse flow-induced oscillations (FIOs) that can be improved by varying the system parameters for a given in-flow velocity: damping, stiffness, and in-flow center-to-center spacing. Compared to a single isolated cylinder, tandem cylinders can harness more hydrokinetic energy due to synergy in FIO. Experimental and numerical methods have been utilized to analyze the FIO and energy harnessing of VIVACE. A surrogate-based model of two tandem cylinders is developed to predict the power harvesting and corresponding efficiency by introducing a backpropagation neural network. It is then utilized to reduce excessive experimental or computational testing. The effects of spacing, damping, and stiffness on harvested power and efficiency of the established prediction-model are analyzed. At each selected flow velocity, optimization results of power harvesting using the prediction-model are calculated under different combinations of damping and stiffness. The main conclusions are: (1) The surrogate model, built on extensive experimental data for tandem cylinders, can predict the cylinder oscillatory response accurately. (2) Increasing the damping ratio range from 0–0.24 to 0–0.30 is beneficial for improving power efficiency, but has no significant effect on power harvesting. (3) In galloping, a spacing ratio of 1.57 has the highest optimal harnessed power and efficiency compared with other spacing values. (4) Two tandem cylinders can harness 2.01–4.67 times the optimal power of an isolated cylinder. In addition, the former can achieve 1.46–4.01 times the efficiency of the latter. (5) The surrogate model is an efficient predictive tool defining parameters of the Converter for improved energy acquisition.

backpropagation neural network↗
DOE OSTI2023

Experimental and numerical study of the shielding effect of two tandem rough cylinders in flow-induce oscillation

The shielding effect of the downstream cylinder in flow induced oscillation (FIO) of two cylinders arranged in tandem is studied experimentally and numerically at Reynolds number 30,000 to 120,000. Both cylinders are in one degree-of-freedom, transverse-oscillations, and have turbulence stimulation in the form of selective surface roughness to expand FIO beyond vortex-induced vibration (VIV) into galloping. Shielding of the downstream cylinder has a negative effect on harnessing hydrokinetic energy. Further, to study its effect and mechanics, selective cases are studied both numerically and experimentally and discussed to demonstrate the shielding effect on the downstream cylinder and understand its cause. The main conclusions are: (1) The shielding effect for the downstream cylinder shows a strong relation to the damping ratio. As the damping ratio increases, the shielding effect is mitigated. Additionally, the oscillation of the rear cylinder becomes stable and shows stable frequency. (2) In the VIV region, as the stiffness and natural frequency increase, the shielding effect decreases substantially. (3) In the VIV region, the vorticity of the vortices shedding from both the upper and the lower sides of the downstream cylinder does not accumulate enough due to the attraction by the vortices shed from the upstream cylinder, thus resulting in partial suppression of the oscillation on the downstream cylinder. (4) In the galloping region, the shielding effect for the downstream cylinder depends on whether the vorticity near the downstream cylinder is strengthened by the vortices generated by the shear layers of the upstream cylinder or weakened.

42 ENGINEERING↗
DOE OSTI2021

Influence of turbulence intensity on vortex pattern for a rigid cylinder with turbulence stimulation in flow induced oscillations

The effect of ambient turbulence intensity on the flow induced oscillations of rigid circular cylinders with symmetric and asymmetric local turbulence stimulation is studied. Cylinders oscillate in one degree of freedom transversely to a steady uniform flow. Two-dimensional unsteady Reynolds-Average Navier-Stokes equations with the Spalart-Allmaras turbulence model are used to solve the problem numerically. Three freestream turbulence intensity values (0.2%, 1%, 5%) are used to study the influence of turbulence intensity on vortex pattern. Simulation results are compared with experimental data measured in the Marine Renewable Energy Laboratory of the University of Michigan in the range of 30,000 ≤ Re ≤ 110,000. The amplitude ratio, lift coefficient, vortex modes, and the interactions between vortices and cylinders are observed and discussed. In conclusion, major conclusions are: (a) Vortex patterns strongly depend on the freestream ambient turbulence intensity. (b) Low turbulence intensity can generate multi-vortex patterns at high Re. (c) High turbulence intensity results in fewer separations of a shed vortex into multiple vortices inducing emergence of elongated vortex patterns.

42 ENGINEERING↗
NASA NTRS1976

Coriolis effects on nonlinear oscillations of rotating cylinders and rings

The effects which moderately large deflections have on the frequency spectrum of rotating rings and cylinders are considered. To develop the requisite solution, a variationally constrained version of the Lindstedt-Poincare procedure is employed. Based on the solution developed, in addition to considering the effects of displacement induced nonlinearity, the role of Coriolis forces is also given special consideration.

Padovan, J.↗
DOE OSTI2022

Hydrokinetic energy conversion using flow induced oscillations of single-cylinder with large passive turbulence control

Various types of flow-induced oscillations (FIOs) have been implemented in development of marine hydrokinetic (MHK) energy converters. With passive turbulence control (PTC), energy harvesting starts at a flow speed of about 0.5 m/s. However, there is worldwide MHK energy available in even slower currents. In the present study, the effect of damping on FIO and power extraction is investigated for a converter with large turbulence stimulation (PTC) consisting of straight strips with a height of 15% of the cylinder diameter and placed symmetrically on the cylinder surface. The oscillating amplitude decreases, as the damping ratio increases, with unchanged sinusoidal pattern of the displacement time-history. The frequency ratio is also affected by damping especially in the VIV initial branch and transition region between VIV and galloping. An important flow characteristic of the large-PTC cylinder is that a recirculation region is formed behind the PTC, causing appreciable disturbance to the flow past the cylinder. Power can be harvested in the whole FIO range and the harnessed power maximum appears at the largest inflow velocity tested. However, the optimum of harnessing efficiency is located at the beginning of the VIV upper branch. The gap between VIV and galloping is bridged when large PTC is used, eliminating the drop in power and efficiency even at higher damping, which would be a weakness of regular-PTC cylinder for energy harvesting. Finally, the mechanism behind the variation of harnessing efficiency with inflow velocity and damping ratio is revealed, and the optimality criterion for the converter design is discussed.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

A Moving Embedded Boundary Approach for the Compressible Navier-Stokes Equations in a Block-Structured Adaptive Refinement Framework

A computational technique has been developed to perform compressible flow simulations involving moving boundaries using an embedded boundary approach within the block-structured adaptive mesh refinement (SAMR) framework of AMReX [1], [91], [92]. We leverage the SAMR capability to obtain quantitatively accurate results whilst using robust, second-order finite volume schemes. A conservative, unsplit, cut-cell approach is utilized and a ghost-cell approach is developed for computing the flux on the moving, embedded boundary faces. A third-order least-squares formulation has been developed to compute the wall velocity gradients, and was found to significantly improve the performance of the solver in terms of the quantitative comparison of surface quantities such as the skin friction coefficient. Various test cases are performed to validate the method, and compared with analytical, experimental, and other numerical results in literature. Inviscid and viscous test cases are performed that span a wide regime of flow speeds - acoustic (harmonically pulsating sphere), smooth flows (expansion fan created by a receding piston) and flows with shocks (shock-cylinder interaction, shock-wedge interaction, pitching NACA 0012 airfoil and shock-cone interaction). A closed system with moving boundaries - an oscillating piston in a cylinder, showed that the percentage error in mass within the system decreases with refinement, demonstrating that the numerical scheme is conservative with grid refinement, but is not discretely conservative. Viscous test cases involve that of a horizontally moving cylinder at Re = 40, an inline oscillating cylinder at Re = 100, and a transversely oscillating cylinder at Re = 185. The judicious use of adaptive mesh refinement with appropriate refinement criteria to capture the regions of interest leads to well-resolved flow features, and good quantitative comparison is observed with the results available in literature.

adaptive refinement↗
DOE OSTI2021

Hydrokinetic Energy Conversion by Flow-Induced Oscillation of Two Tandem Cylinders of Different Stiffness

Abstract The vortex-induced vibration for aquatic clean energy (VIVACE) converter harnesses hydrokinetic energy by enhancing flow-induced oscillations (FIOs) of elastically supported rigid cylinders in a river, tide, or ocean current. The harnessing power depends on the intensity of the oscillation, which is a consequence of the flow–structure interaction. The inflow condition for the downstream (second) cylinder is slowed down and perturbed by the upstream (first) cylinder, due to the shielding effect. Therefore, the optimal structural parameters, i.e., stiffness and damping ratio, for the second cylinder may be different from the first cylinder, in terms of energy harnessing. To improve the performance of the VIVACE converter, a series of experiments are conducted in a recirculating water channel, with various stiffness combinations of two cylinders in tandem. Results show that the stiffness of the second cylinder, K2, does not affect the energy harnessing power in vortex-induced vibration (VIV) occurring at low speeds, because the oscillation of the downstream cylinder in this velocity range is completely dominated by the wake of the upstream cylinder. K2 has a great influence on the harnessing power at higher velocities in the transition region from VIV to galloping and in galloping. Changing K2 onsets and enhances galloping at lower flow velocity and harnesses up to 110% more energy than the case of K1 = K2.

Engineering↗
DOE OSTI2021

Experimental and computational investigation of interactive flow induced oscillations of two tandem rough cylinders at 3×10 4 ≤Re≤1.2×10 5

The interactive flow induced oscillations (FIO) of two adjacent, elastically mounted, rigid, tandem, locally-rough cylinders in transverse flow direction are analyzed utilizing two-dimensional Unsteady Reynolds-Averaged Navier-Stokes (2-D URANS) equations and verified experimentally in the proximity-wake region. Three sets of experiments and simulations (K = 600N/m, ζ = 0.14; K = 600N/m, ζ = 0.26; K = 1,200N/m, ζ = 0.26; K is spring stiffness, ζ is damping ratio) of two tandem cylinders with turbulence stimulation are tested and simulated for Reynolds number in the range of 30,000 = Re ≤ 120,000. The reduced velocity range is U* = 2.48–14.22, the mass ratio is m* = 1.343, and the center-to-center in-flow spacing to diameter ratio is d/D = 2.57. The characteristics of amplitude response, frequency response, lift force, and interactive wake patterns are presented and discussed. The trends of the amplitude and frequency responses from numerical simulations are in good agreement with experimental results. The main conclusions of Reynolds number effect on interactive flow induced oscillations are: (1) Five significant flow patterns between two tandem locally-rough cylinders for different Reynolds numbers are observed through analyzing the complex but stable interactions between vortices and cylinders. (2) In the initial and upper VIV branches, the downstream cylinder's FIO is seriously interfered by the wake of the upstream cylinder. (3) The downstream cylinder is strongly impinged by the vortices shed from the upstream cylinder resulting in nearly 180O out-of-phase oscillations in transition from VIV to galloping and in-phase oscillations in galloping.

42 ENGINEERING↗
NASA NTRS1990

Experimental observations on the relationship between stagnation region flow oscillations and eddy shedding for circular cylinder

Measurements indicate a direct coupling between the dominant frequencies of flow oscillations at the leading-edge stagnation region, laminar-separation unsteadiness, and the vortex shedding. An array of surface mounted, micro-thin hot-films were used to simultaneously determine the state of the boundary layer along the surfaced of a circular cylinder, and vortex shedding was monitored by a hot wire placed in its wake.

Mangalam, S. M.↗