Search NASA⌕ Search

SEARCH · Search NASA

Results for “PECVD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Electron-beam induced damage in thin insulating films on compound semiconductors

Phosphorus rich plasma enhanced chemical vapor deposition (PECVD) of silicon nitride and silicon dioxide films on n-type indium phosphide (InP) substrates were exposed to electron-beam irradiation in the 5 to 40 keV range for the purpose of characterizing the damage induced in the dielectric. The electron-beam exposure was on the range of 10(exp -7) to 10(exp -3) C/sq cm. The damage to the devices was characterized by capacitance-voltage (C-V) measurements of the metal insulator semiconductor (MIS) capacitors. These results were compared to results obtained for radiation damage of thermal silicon dioxide on silicon (Si) MOS capacitors with similar exposures. The radiation induced damage in the PECVD silicon nitride films on InP was successfully annealed out in an hydrogen/nitrogen (H2/N2) ambient at 400 C for 15 min. The PECVD silicon dioxide films on InP had the least radiation damage, while the thermal silicon dioxide films on Si had the most radiation damage.

Pantic, Dragan M.↗
NASA NTRS2005

Growing Aligned Carbon Nanotubes for Interconnections in ICs

A process for growing multiwalled carbon nanotubes anchored at specified locations and aligned along specified directions has been invented. Typically, one would grow a number of the nanotubes oriented perpendicularly to a silicon integrated-circuit (IC) substrate, starting from (and anchored on) patterned catalytic spots on the substrate. Such arrays of perpendicular carbon nanotubes could be used as electrical interconnections between levels of multilevel ICs. The process (see Figure 1) begins with the formation of a layer, a few hundred nanometers thick, of a compatible electrically insulating material (e.g., SiO(x) or Si(y)N(z) on the silicon substrate. A patterned film of a suitable electrical conductor (Al, Mo, Cr, Ti, Ta, Pt, Ir, or doped Si), having a thickness between 1 nm and 2 m, is deposited on the insulating layer to form the IC conductor pattern. Next, a catalytic material (usually, Ni, Fe, or Co) is deposited to a thickness between 1 and 30 nm on the spots from which it is desired to grow carbon nanotubes. The carbon nanotubes are grown by plasma-enhanced chemical vapor deposition (PECVD). Unlike the matted and tangled carbon nanotubes grown by thermal CVD, the carbon nanotubes grown by PECVD are perpendicular and freestanding because an electric field perpendicular to the substrate is used in PECVD. Next, the free space between the carbon nanotubes is filled with SiO2 by means of CVD from tetraethylorthosilicate (TEOS), thereby forming an array of carbon nanotubes embedded in SiO2. Chemical mechanical polishing (CMP) is then performed to remove excess SiO2 and form a flat-top surface in which the outer ends of the carbon nanotubes are exposed. Optionally, depending on the application, metal lines to connect selected ends of carbon nanotubes may be deposited on the top surface. The top part of Figure 2 is a scanning electron micrograph (SEM) of carbon nanotubes grown, as described above, on catalytic spots of about 100 nm diameter patterned by electron-beam lithography. These and other nanotubes were found to have lengths ranging from 2 to 10 m and diameters ranging from 30 to 200 nm, the exact values of length depending on growth times and conditions and the exact values of diameter depending on the diameters and thicknesses of the catalyst spots. The bottom part of Figure 2 is an SEM of an embedded array of carbon nanotubes after CMP.

Li, Jun↗
DOE OSTI2021

Trap-Assisted Dopant Compensation Prevents Shunting in poly-Si Passivating Interdigitated Back Contact Silicon Solar Cells

Interdigitated back contact (IBC) solar cells achieve the highest efficiencies of single-junction architectures, but complicated patterning of the rear fingers and spreading of dopants during processing inhibit their mainstream adoption due to concerns of shunting between the IBC fingers. One method of simplifying patterning at the rear is by using contact masks combined with plasma-enhanced chemical vapor deposition (PECVD) or ion implantation. However, the intrinsic isolation region becomes contaminated during high-temperature annealing by lateral diffusion of dopants and during masked PECVD by spreading of dopant radicals through region between the mask and the substrate. Despite this contamination, we show through scanning spreading resistance microscopy and Kelvin probe force microscopy that a ~20 µm wide compensating region exists with high enough resistivity to prevent shunting. We model this p-i-n poly-Si system using two simulation models: a simple resistor model considering only the capture of charge carriers by trap defects in poly-Si to reduce the conductivity, and a more refined 1-dimensional finite element model using Poisson’s equation, drift-diffusion equations, and recombination of carriers. Using this model, we show that high defect density significantly decreases the current across the region between the p- and n-type fingers, preventing shunting.

atom probe↗
NASA NTRS2011

High-Throughput Processes and Structural Characterization of Single-Nanotube Based Devices for 3D Electronics

We have developed manufacturable approaches to form single, vertically aligned carbon nanotubes, where the tubes are centered precisely, and placed within a few hundred nm of 1-1.5 micron deep trenches. These wafer-scale approaches were enabled by chemically amplified resists and inductively coupled Cryo-etchers to form the 3D nanoscale architectures. The tube growth was performed using dc plasmaenhanced chemical vapor deposition (PECVD), and the materials used for the pre-fabricated 3D architectures were chemically and structurally compatible with the high temperature (700 C) PECVD synthesis of our tubes, in an ammonia and acetylene ambient. The TEM analysis of our tubes revealed graphitic basal planes inclined to the central or fiber axis, with cone angles up to 30 deg. for the particular growth conditions used. In addition, bending tests performed using a custom nanoindentor, suggest that the tubes are well adhered to the Si substrate. Tube characteristics were also engineered to some extent, by adjusting growth parameters, such as Ni catalyst thickness, pressure and plasma power during growth.

top-down fabrication↗
DOE OSTI2023

Self Assembled Monolayers for Passivated Contacts

Passivated contacts mitigate defects typically encountered due metallization of solar cells. We deposit amorphous silicon (a-Si:H) on an oxidized silicon wafer via PECVD and anneal at high temperature to crystallize into polysilicon passivated contact. One drawback is the absorption of the polysilicon between grid fingers, so removal of this material is desirable to maximize Jsc. Alternatively, interdigitated back contact cells rely on a gap between n- and p- fingers, which is commonly etched to ensure electronic isolation. We utilize a self assembled monolayer (SAM) using hexamethyldisilazane (HMDS) as a precursor to pattern and etch amorphous silicon (a-Si:H) and polysilicon without the need for photoresist. Ultraviolet light exposure oxidizes the HMDS by photocleaving the organic groups [1] of the SAM leaving a patterned SiO2. Directly soaking this in TMAH will eventually etch the SAM and the silicon, where the SiO2 serves as an etch mask. Inversely, a dilute HF dip selectively etches this SiO2 and the SAM remains. A subsequent soak in TMAH selectively etches the underlying silicon, where the SAM serves as an etch mask. Importantly, we find that the SAM can remain intact for metallization, where we measure 10 mO-cm2 specific contact resistivity on n-type polysilicon.

passivation↗
DOE OSTI2023

Nucleation of cubic boron nitride on boron-doped diamond via plasma enhanced chemical vapor deposition

Cubic boron nitride (c-BN), with a small 1.4% lattice mismatch with diamond, presents a heterostructure with multiple opportunities for electronic device applications. However, the formation of c-BN/diamond heterostructures has been limited by the tendency to form hexagonal BN at the interface. In this study, c-BN has been deposited on free standing polycrystalline and single crystal boron-doped diamond substrates via electron cyclotron resonance plasma enhanced chemical vapor deposition (ECR-PECVD), employing fluorine chemistry. In situ x-ray photoelectron spectroscopy (XPS) is used to characterize the nucleation and growth of boron nitride (BN) films as a function of hydrogen gas flow rates during deposition. The PECVD growth rate of BN was found to increase with increased hydrogen gas flow. In the absence of hydrogen gas flow, the BN layer was reduced in thickness or etched. The XPS results show that an excess of hydrogen gas significantly increases the percent of sp2 bonding, characteristic of hexagonal BN (h-BN), particularly during initial layer growth. Reducing the hydrogen flow, such that hydrogen gas is the limiting reactant, minimizes the sp2 bonding during the nucleation of BN. TEM results indicate the partial coverage of the diamond with thin epitaxial islands of c-BN. The limited hydrogen reaction is found to be a favorable growth environment for c-BN on boron-doped diamond.

Physics↗
DOE OSTI2022

Selectively patterned Mg-doped GaN by SiN x -driven hydrogen injection

In this work, we demonstrate a method to achieve selectively patterned Mg-doped GaN layers using hydrogen drive-in through plasma-enhanced chemical vapor deposition (PECVD) silicon nitride (SiN x ) films. Activated Mg-doped GaN layers were selectively deactivated by patterned PECVD SiN x films with low-temperature annealing and showed high-resistive behavior. Spatially resolved photoluminescence measurements were used to optically verify the deactivation of Mg acceptors and showed distinct features corresponding to activated and deactivated Mg in GaN. The method suggested here provides a simple and effective method to achieve patterned Mg-doped GaN regions without thermal and plasma damage, which could cause degradation of device performance. The proposed method could provide a way to achieve future high-performance GaN lateral and vertical devices that rely on laterally patterned doping.

42 ENGINEERING↗
DOE OSTI2021

Demonstration of the DC-Kerr effect in silicon-rich nitride

We demonstrate the DC-Kerr effect in plasma enhanced chemical vapor deposition (PECVD) silicon-rich nitride (SRN) and use it to demonstrate a third order nonlinear susceptibility, χ (3) , as high as (6 ± 0.58) × 10 -19 m 2 /V 2 . We employ spectral shift versus applied voltage measurements in a racetrack resonator as a tool to characterize the nonlinear susceptibilities of these films. In doing so, we demonstrate a χ (3) larger than that of silicon and argue that PECVD SRN can provide a versatile platform for employing optical phase shifters while maintaining a low thermal budget using a deposition technique readily available in CMOS process flows.

42 ENGINEERING↗
DOE OSTI2021

Pushing the efficiency limit of low-cost, industrially relevant Si solar cells to > 22.5% by advancing cell structures and technology innovations (Final Report)

The overall objective of this program is to achieve ~23% bifacial n-type cell efficiencies by developing and implementing optimized homogeneous or selective boron (B) emitter on front and tunnel oxide passivated contact (TOPCon) on rear side, in combination with advanced fine-line screen-printing metallization with floating busbars. During this research project, first we developed a technology roadmap to drive the 21% n-PERT cell efficiency from 21% to 23% by transforming the cell design to n-TOPCon and establishing the requirements for each layer, including B emitter, rear n-TOPCon, n-base Si and screen-printed contacts. Next, consistent with our roadmap, we developed advanced homogeneous implanted B emitter (150-180 Ω/⌫) passivated with ALD Al 2 O 3 layer capped with PECVD SiN x /SiO x double-layer antireflection coating This gave a very low recombination current density of 10-15 fA/cm 2 prior to metallization. In addition, we demonstrated metallized recombination current density of ~31 fA/cm 2 for this advanced homogeneous B emitter with industrial screen-printed, fire-through contacts with 40 μm wide grid lines, floating busbars and implementation of an advanced Ag-Al paste which resulted in local or reduced area metal-Si contact under the grid lines with virtually no emitter surface etching. This paste reduced the full area metallized J oe,metal from >1100 fA/cm 2 to ~700 fA/cm 2 . We also developed novel processes for the formation of p + /p ++ selective B emitter by a) single B diffusion with selective etch back and b) two-steps diffusion with implanted B in field region and APCVD B diffusion under the metal grid. We achieved very low un-metallized recombination current density (J 0 ) of ~18 fA/cm 2 for the selective p ++ p + emitters (30/150 Ω/⌫) and metallized J 0 of ~28 fA/cm 2 with ~3% screen-printed metal contact to p ++ regions. Next, we developed the technology for n-TOPCon by growing phosphorus-doped LPCVD and PECVD poly-Si on top of ~ 15Å chemically grown (NAO) tunnel oxide. After an optimized anneal at 875 °C for 30 min, passivated n-TOPCon have unmetallized J 0 of ~ 5 fA/cm 2 which went down further to ~ 1 fA/cm 2 after a 700 Å SiN x capping layer and simulated contact firing cycle at 770 °C. After screen-printed fire-through metallization on this n-TOPCon with ~13% metal coverage, metallized J 0 value increased to only ~5 fA/cm 2 which is among the lowest reported value to the best of our knowledge for screen-printed metallization. Finally, we integrated all the above technology innovations and enhancements and demonstrated low-cost manufacturable screen-printed n-TOPCon bifacial Si solar cell with ~23% efficiencies. Based on the experimental and theoretical understanding developed in this project, we have developed a new technology roadmap that shows that implementation of busbarless contacts, 10-20 ms bulk lifetime Si, and selective B emitter or selective TOPCon on the front can drive ~23% efficient cells achieved in this research to ~25% at low-cost.

14 SOLAR ENERGY↗
DOE OSTI2021

New Approaches to Low-Cost Scalable Doping of Interdigitated back Contact Silicon Solar Cells (Final Report)

The goal of this project was to develop novel approaches to patterning of dopants in the rear fingers of interdigitated back contact (IBC) Si solar cells to reduce the cost of manufacturing this high-efficiency-potential cell architecture. The work throughout this project can be divided into four categories: (a) development of dopant patterning technique using laser scribed Si contacts masks that are mechanically aligned with ~10 μm resolution to the underlying Si substrate; (b) measuring dopant spreading profiles in the isolation region between n- and p-type dopant fingers during plasma-enhanced chemical vapor deposition (PECVD) of doped hydrogenated amorphous silicon (a-Si:H) via shadow masks, and dopant desorption and re-adsorption during high-temperature annealing; (c) understanding the role of dopant compensation on the shunt resistance in contaminated isolation regions through analysis of defect-enhanced compensation; and (d) simulation and fabrication of passivated two-sided grid and back-contact solar cells to demonstrate the use of direct dopant patterning in cell fabrication. For the passivated two-sided grid solar cells, masked deposition was used to demonstrate an improvement in the blue response of the cell by creating a shallow front emitter. During development of the masked PECVD patterning process, we measured 3-D dopant profiles using secondary ion mass spectrometry. After deposition, in the masked region, the phosphorus dopant tail was >100 µm at concentrations >10 19 cm -3 while the boron dopant tail was shorter. During high-temperature crystallization of doped a-Si:H films to polycrystalline Si (poly-Si), phosphorus atoms spread by desorbing from the poly-Si surface and re-adsorbing onto intrinsic poly-Si on adjacent wafers that were separated by several millimeters. These contamination mechanisms resulted in a decrease in resistivity from ~10 5 Ω·cm for intrinsic poly-Si to ~10 -1 Ω·cm for contaminated poly-Si. Mitigation strategies for each contamination mechanism were developed to maintain a resistivity of ~10 5 Ω·cm between doped fingers. During fabrication of the 209 cells created during this project, it was found that despite contamination of the IBC gap through the abovementioned mechanisms, high shunt resistances and FF ~75% were still reached. Investigation into this led to the discovery of defect-enhanced compensation which exists within highly defective poly-Si when net doping concentrations reach the value of defect density (~10 18 cm -3 for many poly-Si films). Simulations guided us in the fabrication of IBCs and the cells fabricated were able to meet the year-end goals for BP 2 and 3 of 15% and 17% IBC cell efficiency, as well as the BP 4 goal of a 1% absolute increase in efficiency for PERC-like devices. However, the most efficient cell created during this project of 18.6% fell short of the 21% final project target. While the champion device fell short in V oc and J sc , many devices fabricated were able to reach the necessary goals of ~40 mA/cm 2 , ~700 mV, and ~75% FF required for a 21% device. The results generated from this project were disseminated through 11 conference presentations and proceedings. Presentations included oral talks at 2019 IEEE PVSC, 2019 MRS Fall Meeting, 2020 PVSEC-30 and 2021 IEEE PVSC, as well as poster presentations at 2020 IEEE PVSC and 2021 SiPV. The project resulted in 2 peer reviewed publications – one published in IEEE Journal of Photovoltaics and one in ACS Applied Energy Materials. The information gained in this project will aid in development of improved processes for fabrication of high-efficiency solar cells and other areas of the semiconductor device industry as well. The IBC cells will also pave the way for higher efficiency tandem devices. Through further manufacturing of high-efficiency solar cells, more of the world’s energy demands can be met through renewable sources, helping to stave off the worst effects that may come about from global climate change.

14 SOLAR ENERGY↗
NASA NTRS1990

Detection Of Gas-Phase Polymerization in SiH4 And GeH4

Inelastic scattering of laser light found to indicate onset of gas-phase polymerization in plasma-enhanced chemical-vapor deposition (PECVD) of photoconductive amorphous hydrogenated silicon/germanium alloy (a-SiGe:H) film. In PECVD process, film deposited from radio-frequency glow-discharge plasma of silane (SiH4) and germane (GeH4) diluted with hydrogen. Gas-phase polymerization undesirable because it causes formation of particulates and defective films.

Shing, Yuh-Han↗
NASA NTRS2005

Carbon Nanotubes/Nanofibers by Plasma Enhanced Chemical Vapour Deposition

Plasma enhanced chemical vapour deposition (PECVD) has been recently used for the production of vertically aligned carbon nanotubedfibers (CN) directly on substrates. These structures are potentially important technologically as electron field emitters (e.g. microguns, microwave amplifiers, displays), nanoelectrodes for sensors, filter media, superhydrophobic surfaces and thermal interface materials for microelectronics. A parametric study on the growth of CN grown by glow discharge dc-PECVD is presented. In this technique, a substrate containing thin film Ni catalyst is exposed to C2H2 and NH3 gases at 700 C. Without plasma, this process is essentially thermal CVD which produces curly spaghetti-like CN as seen in Fig. 1 (a). With the plasma generated by biasing the substrate at -6OOV, we observed that the CN align vertically during growth as shown in Fig. l(b), and that the magnitude of the applied substrate bias affects the degree of alignment. The thickness of the thin film Ni catalyst was found to determine the average diameter and inversely the length of the CN. The yield and density of the CN were controlled by the use of different diffusion barrier materials under the Ni catalyst. Patterned CN growth [Fig. l(c)], with la variation in CN diameter of 4.1% and 6.3% respectively, is achieved by lithographically defining the Ni thin film prior to growth. The shape of the structures could be varied from very straight nanotube-like to conical tip-like nanofibers by increasing the ratio of C2H2 in the gas flow. Due to the plasma decomposition of C2H2, amorphous carbon (a-C) is an undesirable byproduct which could coat the substrate during CN growth. Using a combination of depth profiled Auger electron spectroscopy to study the substrate and in-situ mass spectroscopy to examine gas phase neutrals and ions, the optimal conditions for a-C free growth of CN is determined.

Teo, K. B. K.↗
NASA NTRS2004

Improvement of thermal contact resistance by carbon nanotubes and nanofibers

Interfacial thermal resistance results of various nanotube and nanofiber coatings, prepared by chemical vapor deposition (CVD) methods, are reported at relatively low clamping pressures. The five types of samples examined include multi-walled and single-walled nanotubes growth by CVD, multi-walled nanotubes grown by plasma enhanced CVD (PECVD) and carbon nanofibers of differing aspect ratio grown by PECVD. Of the samples examined, only high aspect ratio nanofibers and thermally grown multi-walled nanotubes show an improvement in thermal contact resistance. The improvement is approximately a 60% lower thermal resistance than a bare Si-Cu interface and is comparable to that attained by commercially available thermal interface materials.

Evaluation Studies↗
NASA NTRS2015

Thermally-Resilient, Broadband Optical Absorber from UV-to-IR Derived from Carbon Nanostructures and Method of Making the Same

A monolithic optical absorber and methods of making same. The monolithic optical absorber uses an array of mutually aligned carbon nanotubes that are grown using a PECVD growth process and a structure that includes a conductive substrate, a refractory template layer and a nucleation layer. Monolithic optical absorbers made according to the described structure and method exhibit high absorptivity, high site densities (greater than 10.sup.9 nanotubes/cm.sup.2), very low reflectivity (below 1%), and high thermal stability in air (up to at least 400.degree. C.). The PECVD process allows the application of such absorbers in a wide variety of end uses.

Kaul, Anupama B.↗
DOE OSTI2020

Structurally controlled deposition of silicon onto nanowires

Provided herein are nanostructures for lithium ion battery electrodes and methods of fabrication. In some embodiments, a nanostructure template coated with a silicon coating is provided. The silicon coating may include a non-conformal, more porous layer and a conformal, denser layer on the non-conformal, more porous layer. In some embodiments, two different deposition processes, e.g., a PECVD layer to deposit the non-conformal layer and a thermal CVD process to deposit the conformal layer, are used. Anodes including the nanostructures have longer cycle lifetimes than anodes made using either a PECVD or thermal CVD method alone.

25 ENERGY STORAGE↗
DOE OSTI2022

Structurally controlled deposition of silicon onto nanowires

Provided herein are nanostructures for lithium ion battery electrodes and methods of fabrication. In some embodiments, a nanostructure template coated with a silicon coating is provided. The silicon coating may include a non-conformal, more porous layer and a conformal, denser layer on the non-conformal, more porous layer. In some embodiments, two different deposition processes, e.g., a PECVD layer to deposit the non-conformal layer and a thermal CVD process to deposit the conformal layer, are used. Anodes including the nanostructures have longer cycle lifetimes than anodes made using either a PECVD or thermal CVD method alone.

Wang, Weijie↗
DOE OSTI2023

Mechanism of Hydrogen Passivation in Passivated Contact Si Solar Cells

In this abstract, we discuss the mechanism of hydrogen passivation on symmetrical n-Si/ultra-thin SiO2/polySi structures. The hydrogen was introduced from different hydrogen-containing dielectric layers (AlOx:H and SiNx:H and their stacks), as well as by forming gas anneal (FGA). The effusion of hydrogen both from the dielectric layers and in the underlying poly-Si was explored using a quadrupole mass spectrometer (QMS) and FTIR spectroscopy. We show that the strength of hydrogen bonds depend on the deposition technique as well as hydrogenation mechanism. While a PECVD SiNx:H loses hydrogen at a peak temperature of ~450 degrees C, LPCVD SiNx:H, although having less hydrogen compared to PECVD, effuses at a peak temperature of ~850 degrees C. This becomes important to maintain passivation of passivated contacts after firing of metal contacts at high temperatures. On the other hand, it has been observed that SiNx:H provides larger amount of hydrogen to poly-Si after FGA compared to FGA treated AlOx:H, which acts as a capping layer and helps in retaining the hydrogen up to higher temperatures.

hydrogen bonding configuration↗
DOE OSTI2023

Structurally controlled deposition of silicon onto nanowires

Provided herein are nanostructures for lithium ion battery electrodes and methods of fabrication. In some embodiments, a nanostructure template coated with a silicon coating is provided. The silicon coating may include a non-conformal, more porous layer and a conformal, denser layer on the non-conformal, more porous layer. In some embodiments, two different deposition processes, e.g., a PECVD layer to deposit the non-conformal layer and a thermal CVD process to deposit the conformal layer, are used. Anodes including the nanostructures have longer cycle lifetimes than anodes made using either a PECVD or thermal CVD method alone.

Wang, Weijie↗