Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Tungsten disulfide nanotubes enhance flow-induced crystallization and radio-opacity of polylactide without adversely affecting in vitro toxicity

Treatment of vascular disease, from peripheral ischemia to coronary heart disease (CHD), is poised for transformation with the introduction of transient implants designed to “scaffold” regeneration of blood vessels and ultimately leave nothing behind. Improved materials could expand the use of these devices. Here, we examine one of the leading polymers for bioresorbable scaffolds (BRS), polylactide (PLA), as the matrix of nanocomposites with tungsten disulfide (WS 2 ) nanotubes (WSNT), which may provide mechanical reinforcement and enhance radio-opacity. We evaluate in vitro cytotoxicity using vascular cells, flow-induced crystallization and radio-opacity of PLA-WSNT nanocomposites at low WSNT concentration. A small amount of WSNT (0.1 wt%) can effectively promote oriented crystallization of PLA without compromising molecular weight. And radio-opacity improves significantly: as little as 0.5 to 1 wt% WSNT doubles the radio-opacity of PLA-WSNT relative to PLA at 17 keV. The results suggest that a single component, WSNT, has the potential to increase the strength of BRS to enable thinner devices and increase radio-opacity to improve intraoperative visualization. Here, the in vitro toxicity results indicate that PLA-WSNT nanocomposites are worthy of investigation in vivo. Although substantial further preclinical studies are needed, PLA-WSNT nanocomposites may provide a complement of material properties that may improve BRS and expand the range of lesions that can be treated using transient implants.

36 MATERIALS SCIENCE↗
DOE OSTI2026

3D printed water-stable Cd-doped Cs 4 MnBi 2 Cl 12 /polylactic acid perovskite/polymer composites for high-flux X-ray scintillation

Stable and efficient X-ray scintillators are crucial for medical diagnostics, industrial, and defense applications. However, conventional scintillator technologies face a trade-off between stability, optimal performance, and sustainability. Herein, we introduce 3D-printed Cs 4 MnBi 2 Cl 12 (Pero1) and Cs 4 Cd 0.68 Mn 0.32 Bi 2 Cl 12 (Pero2) perovskite microcrystals embedded within a polylactic acid (PLA) polymer composite as X-ray scintillators, combining efficiency, stability, and sustainability. The orange luminescent perovskite powder phosphors exhibited poor water stability, which was successfully addressed through incorporation into PLA via filament extrusion and fused deposition modeling (FDM) 3D printing. The resulting composite films demonstrated remarkable water stability while maintaining uniform orange emission throughout the polymer matrix, as confirmed by 3D topography scanning and X-ray fluorescence mapping. Structural characterization revealed minimal chemical interaction between the perovskite and PLA matrix, with the composites retaining their crystalline properties. The PLA-Pero2 composite exhibited superior optical properties, with a photoluminescence quantum yield of 47%, nearly 17 times higher than that of PLA-Pero1 (2.8%), attributed to the effective suppression of non-radiative decay pathways through Cd 2+ doping. Under hard X-ray irradiation at synchrotron beamlines, both composites exhibited excellent radioluminescence, with emission peaks at 605 nm, a linear response across a wide X-ray flux range, and remarkable radiation stability, showing less than 3% intensity degradation after 600 seconds of continuous high-dose exposure. The PLA-Pero2 composite achieved a spatial resolution of 5 line pairs per millimeter and a contrast ratio of 0.255. These performance metrics, combined with the polymer's biodegradability and scalability through additive manufacturing, position PLA-based composites as a more sustainable alternative to conventional petroleum-based polymer scintillators for next-generation medical imaging, radiation monitoring, and industrial radiography applications.

3D Printing↗
DOE OSTI2022

Exploiting chitosan to improve the interface of nanocellulose reinforced polymer composites

Cellulose nanofibrils (CNFs) have been widely used as a nanofiller for polymer composite reinforcement due to their excellent mechanical properties. However, CNF is produced in water and needs to be dried prior to use in composite materials. The presence of hydroxyl groups on the surface of CNF creates strong hydrogen bonding that makes it difficult and costly to dry. Additionally, the hydrophilicity at the fiber surface results in agglomeration of CNFs within many polymer matrices. In this study, chitosan (CS) was co-precipitated with CNF to produce a dual-bonding filler for use in poly (lactic acid) (PLA) composites. CS promotes improved interfacial interaction within the polymer matrix by forming strong hydrogen bonds with the CNF and potential covalent bonds with the PLA. Finally, the results confirmed that the addition of a small amount of CS significantly improved the mechanical properties compared to PLA + CNF composites and neat PLA. The detailed study of the PLA + CNF/CS composites reveals the synergetic effect of the hydrogen and covalent bonding mechanism for PLA reinforcement.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Strengthening poly(lactic acid) composites with poly(methyl methacrylate) functionalized flax nanofibrils

Biobased reinforcements for poly(lactic acid) (PLA) are needed for more additive manufacturing applications requiring higher strength and sustainability. Flax nanofibrils (FNFs) produced through mechanical refining were explored as a lower energy alternative to cellulose nanofibril (CNF) reinforcements. To compatibilize the FNFs for the PLA matrix, a grafting-through surfactant free emulsion polymerization (SFEP) was performed to functionalize the FNF surface with poly(methyl methacrylate) (PMMA). FNFs produced using different refining energy were functionalized under varying solid contents in suspension. Polymerizations performed at 0.7 wt% FNFs in water yielded the highest degree of PMMA functionality. These optimal conditions were scaled up and the PMMA modified FNFs melt compounded into PLA yielding a 12% increase in tensile strength and 92% increase in the modulus of elasticity as compared to the original PLA. Interestingly, the FNFs with the lowest refining energy yielded the strongest composites using these methods, surpassing the higher refining energy CNF reinforcements. This increase was attributed to improved dispersion of the FNF reinforcements in the PLA matrix that was enabled by the PMMA coating on the FNF surface preventing interfibrillar adhesion and aggregation within the PLA matrix.

Mulligan, Abigail [University of Maine]↗
DOE OSTI2025

Bacterial-Retted Hemp Fiber/PLA Composites

The push for sustainability in all facets of manufacturing has led to an increased interest in biomass as an alternative to non-renewable materials. Hemp bast fiber mats were produced from a bacterial retting process, named BFM, as the fiber reinforcement. The objective of this study was to evaluate the feasibility of laminating BFM with polylactic acid (PLA) for a composite panel product. Since both BFM and PLA are biodegradable, the resulting BFM-PLA composites will be 100% biodegradable. PLA pallets were processed into thin polymer sheets which served as the matrix. The BFM and PLA plates were laminated in five layers and compression-molded into composite panels. Experiments were conducted on the three BFM-to-PLA ratios (35/65, 45/55, and 50/50). Mechanical properties (tensile and bending properties) and physical properties (thickness swell and water absorption) were tested and compared to the currently commercial sheet molding compound (SMC) from fiber glass. The thermal behavior of the BFM/PLA composites was characterized using dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). The developed BFM/PLA composite product is a sustainable alternative to existing synthetical fiber-reinforced polymer (FRP) that is biodegradable in landfill at the end of life.

Smith, Lee M. (ORCID:0000000264390357)↗
DOE OSTI2020

Life cycle greenhouse gas emissions and energy use of polylactic acid, bio-derived polyethylene, and fossil-derived polyethylene

Bioplastics recently have become an attractive, viable, and popular alternative to conventional petroleum-based plastics, with the hope that replacing fossil-derived plastics with renewable alternatives will reduce greenhouse gas (GHG) emissions and fossil energy consumption (FEC). The bioplastic industry is encouraging creative designs and enhanced properties such as biodegradability, which is considered a sustainable solution for waste plastic management. However, biodegradability also means that carbon in the product is emitted to the atmosphere as GHG emissions. In this paper, a life cycle analysis (LCA) of biodegradable polylactic acid (PLA) and bio-polyethylene (bio-PE) plastics was conducted to understand the environmental effects of these bioplastics from feedstock production to product end-of-life (EOL). In particular, emissions from biodegradability (EOL emissions) are accounted for. The results were compared to those of conventional fossil-based plastics such as high-density polyethylene (HDPE) and low-density polyethylene (LDPE). Results showed that the lowest GHG emissions (-1.0 and 1.7 kg CO 2 e per kg for bio-PE and PLA with no biodegradation, respectively) and FEC (29 and 46 MJ per kg of bio-PE and PLA, respectively) were achieved with bio-derived plastics, particularly bio-PE plastic. However, despite the benefits of biogenic carbon uptake, when landfill and composting emissions were considered for the PLA pathway, the life cycle emissions of PLA increase significantly, from 16% to 163% depending on the biodegradation condition, compared to the case where there is no degradation in the landfill. This study also contributed to understand the effects on the GHG emissions of biodegradability in landfill and composting scenarios, regional electricity mix, and plastics manufacturing technologies. (C) 2020 The Authors. Published by Elsevier Ltd.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

A synergistic approach to improve the cellulose nanofibril dispersion in poly(lactic acid) composites as feedstocks for extrusion-based additive manufacturing

Hybrid fiber-reinforced polymer composites (HFRPs) are multifunctional materials that bear more than one characteristic benefit. In this study, hybrid cellulose fibers, e.g., pulp fiber (PF) and cellulose nanofibril (CNF), were used for reinforcing poly(lactic acid) (PLA). A synergistic approach was applied to disperse CNF. The low-surface-tension solvent (ethanol), together with PF templating, assisted the dispersion of CNF in PLA. The HFRP achieved a higher tensile strength (∼70 MPa, 29% increase from PLA) and modulus (∼7 GPa, 46% increase from PLA), as well as a higher heat deflection temperature (∼60℃, 6℃ increase compared to neat PLA), compared to single-reinforcement FRPs. Additionally, the formulation was demonstrated to be potentially suitable for large-scale additive manufacturing.

Bista, Bivek [University of Maine]↗
DOE OSTI2021

Effect of stereochemistry on nanoscale assembly of ABA triblock copolymers with crystallizable blocks

We report on the nanoscale assembly of poly(lactic acid)-b-poly(ethylene oxide)-b-poly(lactic acid) (PLA-PEO-PLA) triblock copolymers in water, focusing on the effect of stereochemistry, where the PLA blocks are statistical copolymers of l-lactide and d-lactide with l/d ratios of 100/0, 95/5, 90/10, 85/15, 75/25, and 50/50. Small-angle neutron scattering (SANS) shows a nearly constant d-spacing as concentration varies in triblock systems with l/d ratios of 90/10 and 95/5, which we attribute to inhomogeneity in the structure of these gels, supported by previous USANS and confocal microscopy studies. The SANS data fit well to a core-shell ellipsoid form factor model with a hard-sphere structure factor. Polymeric micelles with l/d ratios from 75/25 to 85/15 displayed very high aggregation numbers, consistent with a strong interaction between PLA chains and the enhanced storage modulus observed in rheological studies of these systems. While the 90/10 and 95/5 samples showed lower aggregation numbers, their SANS profiles shows close spacing between micelles, which may promote a high fraction of intermicellar bridging chains, also consistent with a higher storage modulus. Overall, these results provide insight into the micellar assembly behavior of block copolymers with a crystallizable block, and indicate that tuning stereochemistry of PLA-based block copolymers is an effective means of modifying micellar properties for specific applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

On the Interfacial Behavior of Catenated Poly(l-lactide) at the Air–Water Interface

Interfacial properties of polymeric materials are significantly influenced by their architectural structures and spatial features, while such a study of topologically interesting macromolecules is rarely reported. Here, we reported, for the first time, the interfacial behavior of catenated poly(l-lactide) (C-PLA) at the air–water interface and compared it with its linear analogue (L-PLA). The isotherms of surface pressure–area per repeating unit showed significant interfacial behavioral differences between the two polymers with different topologies. Isobaric creep experiments and compression–expansion cycles also showed that C-PLA demonstrated higher stability at the air–water interface. Interestingly, when the films at different surface pressures were transferred via the Langmuir–Blodgett method, successive atomic force microscopy imaging displayed distinct nanomorphologies, in which the surface of C-PLA exhibited nanofibrous structures, while that of the L-PLA revealed a smoother topology with less fiber-like structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Interconnected Nanoporous Polysulfone by the Self-Assembly of Randomly Linked Copolymer Networks and Linear Multiblocks

Porous materials have attracted considerable attention due to their versatile applications, especially in water purification. Interconnected nanoporous structures are distinguished by their high degree of porosity and resistance to clogging, as well as their insensitivity to nanostructural orientation. Previous works on randomly linked copolymer systems have shown that they can effectively produce disordered cocontinuous nanostructures, which upon removal of one component yield interconnected nanoporous materials. However, the cocontinuous nanomaterials previously developed using polystyrene (PS) and poly(d,l-lactic acid) (PLA) strands, and the resulting interconnected nanoporous PS monoliths, were far too brittle to enable practical use as membranes. Here, we study the self-assembly of randomly linked copolymer networks prepared using blocks of the engineering polymer polysulfone (PSU). A wide cocontinuous regime (spanning 40 wt %) was found for randomly end-linked copolymer networks (RECNs) constructed from PSU and PLA strands, via a combination of mechanical testing, gravimetry, small-angle X-ray scattering, and scanning electron microscopy. The PSU/PLA cocontinuous nanomaterial with symmetric composition showed 2.4 times higher Young’s modulus and ~100 times greater toughness than the corresponding PS/PLA sample. The interconnected nanoporous PSU fabricated after etching of PLA even exhibited 1.6 times greater toughness than PS/PLA prior to PLA removal. To facilitate the production of thin films of cocontinuous nanomaterials, we applied solution-processable randomly linked linear PSU/PLA multiblock polymers onto ultrafiltration membranes. Here, the interconnected nanoporous PSU thin film generated by etching PLA was found to effectively reject 50 nm diameter particles without significantly compromising permeability. This discovery presents a valuable addition to the existing techniques used to fabricate PSU membranes. In contrast to traditional methods, which are sensitive to processing conditions, produce a wide range of pore sizes, and offer limited adjustability of pore size, the current technique is anticipated to enable interconnected PSU membranes with more uniform and tailorable porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Polymer-Grafted Cellulose Nanofibrils with Enhanced Interfacial Compatibility for Stronger Poly(lactic acid) Composites

Cellulose nanofibrils (CNFs) are a promising reinforcement for biodegradable composite matrices such as poly(lactic acid) (PLA), but they require commercially scalable drying methods that preserve their fibrillar morphology along with improved interfacial interactions with polymer matrices. In this work, a water-based grafting-through polymerization scheme to modify CNFs improved spray drying behavior and reinforcement capacity in PLA composites. All polymer modifications yielded CNFs with a more fibrillar morphology after spray drying, increasing specific surface area by up to 490% compared to unmodified CNFs, values similar to conventional freeze drying. Polymer-grafted CNFs in PLA composites improved the tensile strength by 16% at 20 wt % loading and stiffness by 22% at a 10 wt % loading with two different graft-polymer chemistries compared to unmodified CNF composites. Surface energy heterogeneity measurements of the reinforcements and PLA matrix were employed to understand the improvements in composite properties. Polymer modifications lowered the total surface energy of the CNFs, and calculated ratios of work of adhesion to work of cohesion suggested improved interfacial compatibility for four of the modified CNFs with PLA. Rheological oscillatory shear studies of the composites correlated solid-like melt behavior, as demonstrated by storage moduli dominance, with higher tensile strength. Thermal analysis of the composites revealed that excessive plasticization by the poly(oligoethylene glycol methyl ether methacrylate)-grafted sample potentially offset mechanical property improvements imparted by the more fibrillar morphology. This work provides an opportunity for large-scale manufacturing of CNF/PLA composites via an entirely aqueous modification scheme and industrially relevant spray drying process.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multiscale Modeling and Experimental Insights into High-Temperature Soil Biodegradation Dynamics of Semi-Crystalline Poly(Lactic Acid) Nonwoven Fabrics

This study investigates the biodegradation of semi-crystalline poly(lactic acid) (PLA) nonwovens (NWs) in soil at 58 °C using both experimental and mathematical modeling approaches. The model utilizes a system of parabolic diffusion-reaction partial differential equations (PDEs) to elucidate chemical transformations over time and in space. It accounts for phenomena such as the diffusion of water and lactic acid monomers through the polymer matrix and into the surrounding soil, along with their microbial breakdown. It also accounts for the initial PLA crystallinity and predicts its evolution in time. The model is solved numerically for a single filament, and the results were used to shed light on PLA NW transformations observed in soil over a 180-day incubation period. Various characterization techniques, including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and Raman spectroscopy, were employed to assess morphological changes, crystallinity, and molecular changes in the NWs throughout the experiment. By comparing the experimental data with the model predictions, the hydrolysis rate coefficient was found to be 3.37 × 10 -7 s -1 , while the rate of microbial degradation of lactic acid monomers was faster, of the order of 9.63 × 10 -7 s -1 . The findings highlight the significant role of crystallinity in the biodegradation process. The PLA degradation ceases when no amorphous material remains, and the crystallinity reaches 0.8, as observed in the experiments by day 120. Furthermore, this research contributes to a deeper understanding of PLA biodegradation dynamics and offers insights for effectively managing biodegradable materials in environmental settings.

Diffusion−reaction modeling↗
DOE OSTI2022

Effects of Testosterone on Mixed-Muscle Protein Synthesis and Proteome Dynamics During Energy Deficit

Effects of testosterone on integrated muscle protein metabolism and muscle mass during energy deficit are undetermined. The objective was to determine the effects of testosterone on mixed-muscle protein synthesis (MPS), proteome-wide fractional synthesis rates (FSR), and skeletal muscle mass during energy deficit. This was a randomized, double-blind, placebo-controlled trial. The study was conducted at Pennington Biomedical Research Center. Fifty healthy men. The study consisted of 14 days of weight maintenance, followed by a 28-day 55% energy deficit with 200 mg testosterone enanthate (TEST, n = 24) or placebo (PLA, n = 26) weekly, and up to 42 days of ad libitum recovery feeding. Mixed-MPS and proteome-wide FSR before (Pre), during (Mid), and after (Post) the energy deficit were determined using heavy water (days 1-42) and muscle biopsies. Muscle mass was determined using the D3-creatine dilution method. Mixed-MPS was lower than Pre at Mid and Post (P < 0.0005), with no difference between TEST and PLA. The proportion of individual proteins with numerically higher FSR in TEST than PLA was significant by 2-tailed binomial test at Post (52/67; P < 0.05), but not Mid (32/67; P > 0.05). Muscle mass was unchanged during energy deficit but was greater in TEST than PLA during recovery (P < 0.05). The high proportion of individual proteins with greater FSR in TEST than PLA at Post suggests exogenous testosterone exerted a delayed but broad stimulatory effect on synthesis rates across the muscle proteome during energy deficit, resulting in muscle mass accretion during subsequent recovery.

Endocrinology & Metabolism↗
DOE OSTI2025

Simultaneous Degradation‐Depolymerization of Bioderived Comb Copolymers

Poly(lactic acid) (PLA) is the most widely explored biodegradable alternative for polystyrene; however, its low toughness and glass transition temperature may limit its wider adoption as a sustainable replacement. To improve its material and thermal properties, PLA can be chemically or physically combined with other polymers, like poly(methyl methacrylate) (PMMA), though the incorporation of vinyl‐based polymer components complicates chemical recycling and reduces the sustainability of the material. Here, in this study, we synthesized polymethacrylate‐PLA comb copolymers designed to be thermally deconstructed. Our design strategically extends current polymer deconstruction methodologies to more complex macromolecular systems. Thermally labile units within the polymethacrylate backbone permitted depolymerization that was concurrent with PLA side chain degradation during heating. This dual degradation‐depolymerization process enhances the overall sustainability of lactide/vinyl‐based copolymers and demonstrates the synergistic potential of integrating multiple deconstruction pathways into a single system. This report elaborates on the design of advanced, degradable copolymers, contributing to the further development of sustainable polymer materials.

PLA↗
DOE OSTI2024

Exploring biofiber properties and their influence on biocomposite tensile properties

Biofibers serve as effective reinforcements for neat polylactic acid (PLA) in biocomposites, offering an attractive opportunity to decarbonize the manufacturing sector of the United States by displacing fossil-based reinforcement fibers such as carbon fibers. Also, biofiber production can stimulate economic growth in rural economies, fueling sustainable development. PLA resins are commonly compounded with biofibers to create biocomposites suitable for additive manufacturing. PLA-biofiber composites often exhibit better overall material properties than neat (pure) PLA, but the associations between biofiber properties and the material properties of their biocomposites remain largely unexplored. Hence, this research delves into a comprehensive exploration of diverse biofibers, scrutinizing their physical and chemical attributes, including size, shape, ash content and biochemical composition. The study meticulously analyzes the flow properties of each biofiber and elucidates the ultimate tensile strengths and Young's modulus of corresponding biocomposite samples. Noteworthy correlations between biofiber and biocomposite tensile properties are uncovered, shedding light on critical interrelationships. The study introduces an approach employing regression models to predict the ultimate tensile strength and Young's modulus of biocomposites. These models, validated with a cross-validation technique, exhibit remarkable predictive accuracy, particularly in estimating ultimate tensile strength. © 2024 Oak Ridge National Laboratory managed by UT-Battelle, LLC and The Author(s). Polymer International published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The effect of polymer grafting on the mechanical properties of PEG-grafted cellulose nanocrystals in poly(lactic acid)

Poly(lactic acid) (PLA) is a commercially available bio-based polymer that is a potential alternative to many commodity petrochemical-based polymers. However, PLA's thermomechanical properties limit its use in many applications. Incorporating polymer-grafted cellulose nanocrystals (CNCs) is one potential route to improving these mechanical properties. One key challenge in using these polymer-grafted nanoparticles is to understand which variables associated with polymer grafting are most important for improving composite properties. In this work, poly(ethylene glycol)-grafted CNCs are used to study the effects of polymer grafting density and molecular weight on the properties of PLA composites. All CNC nanofillers are found to reinforce PLA above the glass transition temperature, but non-grafted CNCs and CNCs grafted with short PEG chains (<2 kg mol –1 ) are found to cause significant embrittlement, generally resulting in less than 3% elongation-at-break. By grafting higher molecular weight PEG (10 kg mol –1 ) onto the CNCs at a grafting density where the polymer chains are predicted to be in the semi-dilute polymer brush conformation (~0.1 chains nm –2 ), embrittlement can be avoided.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Printing polymer blends through in situ active mixing during fused filament fabrication

Fused filament fabrication (FFF) enables production of 3D objects over a range of material compositions at low-cost relative to traditional manufacturing approaches. To date, a limited but growing number of materials are able to be used with FFF, however many applications exist where specific mechanical, thermal, or chemical properties are needed that cannot currently be met with the available feedstock selection. Therefore, a need exists to tune these materials for specific chemical or mechanical properties. One common formulation strategy to address these demanding design parameters is to develop composites or polymer blend filaments. Typically, this is a time-consuming and costly optimization process. Here, we have developed hardware for reproducibly mixing two filaments of similar or dissimilar compositions at the time of printing within individual printed layers. This mixing occurs via software-controlled rotating hardware in the chamber of an extruder’s hot-end. The efficiency of mixing within the printed layers has been characterized in detail as a function of the rotational speed and geometry of the blending hardware. These parameters were exploited to program the ratio and distribution of thermoplastic-based filaments blended within printed extrudate. Example printed specimens were produced with thermoplastic polyurethane (TPU) elastomer blended with rigid polylactic acid (PLA) and Nylon blended with PLA. In addition, a conductive carbon nanotube (CNT)-PLA composite was blended as a function of mixer geometry and input feed ratios with non-conductive PLA and resistance values were measured across the resulting printed specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermal conductivity of 3D-printed block-copolymer-inspired structures

This study primarily focuses on examining the impact that geometric structure has on thermal conductivity of multi-phase constructs in different 3D-printed poly(lactic acid), PLA, samples. The investigated structures are inspired by morphologies formed by diblock copolymers: lamellae, hexagonally packed cylinders, and gyroid. This research also investigates how volume percentage and material combination influence the thermal conductivity of these structures. Further, the samples can be tailored to simulate various thermal management structures observed in practical applications, such as thermal interface materials in electronic devices. Thermal conductivity ratio is controlled using air, the least conductive material at 0.026 W/(m K), PLA at 0.136 W/(m K), and thermal paste at 5.11 W/(m K). Different models were tested against thermal conductivity measurements in order to capture the effect of material type (PLA-Air versus PLA-Thermal Paste), volume percentage, structure, and orientation. Simple, effective medium models were good predictions of thermal conductivity in lamellar structures, but it was necessary to develop models for conduction through cylindrical and gyroid structures. Finally, all results were normalized to find a universal model that is independent of structure and material. This approach provides a simple method to predict how to reduce or enhance transport properties and heat management capabilities of 3D printed objects.

36 MATERIALS SCIENCE↗